Responding to more demand in coming years, the task of the small wind energy industry requires progress on several fronts—the public policy initiatives, technology development, and market growth. One important issue of the wind energy utilization is the conversion efficiency of the usable energy into productive power. Enhanced technologies such as contrarotating blades, gearbox and lubrication, airfoils, generators, and power electronics will lower cost and increase energy production. The purpose of this paper is, therefore, to reinforce the effectiveness of employing contrarotating system to enhance the performance of a small wind energy converter (SWEC). With this concept, the SWEC works more efficiently and therefore produces more energy in a unit turbine area. To verify the SWEC performance, a research model has been built and tested over a range of operating conditions. Wind tunnel tests were carried out to ascertain the overall performance of the contrarotating SWEC. Results are presented for cases of different wind speeds and Reynolds number. The results demonstrated a significant increase in wind energy conversion efficiency and capability of operation at lower wind speeds while keeping up performance compared to a single-rotor system of the same type.
Wind energy has been shown to be one of the most feasible sources of renewable energy. It presents attractive opportunities to a wide range of people, including investors and entrepreneurs. The main goal of wind energy industry is to minimize the cost of wind energy in order to make it more competitive compared to other energy sources. How to reduce the cost of wind energy is a vital engineering challenge presented by the interlocking disciplines of aerodynamics, structure, control, electrical conversion, and electronics. In fact, technologies in these related areas are still under active research and development to achieve high efficiency and low cost.
In the shadows of advancing multimegawatt wind turbines is another growing sector within this industry, the small wind turbines. Small wind energy converters (SWECs) for urban or rural applications range in size from a few hundred watts to thousands of watts (usually with a rated capacity of less than 100 kW) and can be applied economically for a variety of power demands. These systems can be used in connection with an electricity transmission and distribution system, or in stand-alone applications that are not connected to the utility grid and are appropriate for homes, farms, or even entire communities. Investments in this sector are feasible not as stand-alone only, but as components of an integrated power-generating system that include various forms of energy resources. The main technical challenges for SWECs are the design of a system that has maximum efficiency in turbulent low speed winds; ability to comply with both efficiency expectations and the requirements of grid utilities; and have the minimum environmental and health impacts in terms of noise and vibration.
Two facts characterize the urban environment for wind energy: lower annual mean wind speed (AMWS) compared to rural areas or to sea shores and more turbulent flow. The low AMWS is related to the uneven ground created by buildings and other features of the urban landscape, which causes wind speeds to increase with height above the ground more slowly. The turbulent flow is a result of the wind interacting with landscape obstacles, the fact that applies extra stress on the turbine blades. The challenge is to develop wind turbines that operate at lower speeds and cope with the turbulent.
The wind generating technology development is leading to improved performance and efficiency. Most wind turbines are single-rotor systems, which provide simplicity, reliability, and durability. Along the years, improvements have enhanced energy conversion efficiency of these single-rotor systems. For example, blades have better aerodynamic characteristics, gears with reduced noise have better torque transmission efficiency, and alternators have better electrical efficiency. However, despite these improvements, single-rotor systems are able to convert only a small fraction of the total wind stream energy into electrical energy. Moreover, such a system requires high wind velocity (above 4 m/s) which is not available in many places, a part from costal regions. This low velocity and seasonal winds imply a high cost of exploitation of wind energy. Thus, the challenge lies with the design of a wind generator which can operate at lower speeds and be used in a small-scale manner in remote and rural areas.
This paper investigates the performance of the SWEC basing on wind tunnel tests. The paper is organized as follows. Section
The prime mover in wind energy system is the wind turbine. One prevailing trend in wind turbine technology throughout the past couple of decades has been growth in the size of the rotor to realize the advantages of scale and the generally higher winds available at greater heights. Geometrically, consistent upscaling of blade length shows that the surface stresses at the blade surface, vibratory loads, and loading noise due to aerodynamical and gravitational loads grow in proportion to the length of the blade [
According to Betz theory, the maximum power that can be extracted from the wind is about 59% of the available energy in the wind when the axial wind speed is reduced by two-thirds across a single rotor disc. However, practical wind turbines convert less than 40% of the wind energy into electrical energy. Hence, nearly 60% of the potential wind energy escapes without being harnessed. In reality, the energy in the wake behind a single rotor is not very small. Part of this energy may be extracted further by installing a second rotor in the wake. As the wake behind the first rotor is rotating in the opposite direction to the rotational direction of the rotor, the second rotor should rotate in the same direction as the wake in order to extract efficiently the available energy in the wake.
The contrarotating system is a very old concept that was initially proposed more than 100 years ago. A friend of Betz who is sometimes described as the “father of modern wind energy collection theory,” Hans Honneff, wrote a book on the use of contrarotation, using two rotors one behind the other, driving the two halves of an electrical generator, therefore creating a true wind turbine [
A dual-rotor system can be described as a system consisting of two rotors separated by an appropriate distance (Figure
The proposed contrarotating small wind energy converter (SWEC).
Based on evidence in literature, aerodynamic research is poised between experimental and computational: either the wind turbine is studied experimentally in a wind tunnel, or the turbine is investigated computationally using methods that belong to the field of computational fluid dynamics (CFD). The two are closely linked, and as progress is made in the development of more advanced computational fluid models, more comprehensive wind tunnel experimental data is required to validate the models. Experimental and computational research provide results for better understanding of the flow physics and enable investigation of wind energy performance, a requirement in order to adjust the design of wind turbines to the unique aerodynamic conditions in the environment. As with all methods of analysis, the CFD approach has limitations which are essentially related to turbulence modeling. Sumner et al. [
According to [
Research studies provide sufficient evidence to look closer at the concept of contrarotating system to eventually produce quantifiable comparisons to other turbines [
A feasibility study [
The contrarotating SWEC clearly has a promise for wind energy, and after preliminary research and field studies [
The motion of any fluid can be derived from the basic physical principles of mass, momentum, and energy interchange. The torque responsible for power production of the wind turbine mostly arises due to the forces produced by interaction of blades with the wind. The output power
Most turbines extract the maximum possible energy as defined above for lower wind speeds but gradually become less efficient as the on-coming wind speed increases and the flow condition across the blades approaches the stall condition.
The rotor power coefficient
The wind turbine mechanical characteristics are described by the following equation (where the turbine rotor friction is ignored):
The incoming wind flow rate should be equal to the outgoing flow rate to satisfy the mass conservation law if a control volume around a turbine is assumed. The outgoing wind-speed distribution and its direction strongly determine the turbine efficiency. Figure
Stream tube passing the rotor plane.
In this section, laboratory measurement techniques are discussed; however, some of the methods used are conventional and require little elaboration.
An open-return type wind tunnel is used in the present study. A contrarotating model 3-blade wind turbine was placed in the boundary-layer wind tunnel with the goal of studying power performance, turbulence effect, and flow visualization. Figure
Wind tunnel test facility. (a) Electrical part of the setup. (b) Instrumentation setup via LabView.
In order to control the ambient turbulence level, turbulence manipulators are placed upstream of the rotor, including a fine mesh screen and an aluminum honeycomb section. Smoothing is provided by the fine mesh screen. The honeycomb plays the role of a flow straightener. When the wind turbine is stopped, the mean velocity over the center portion of the wind tunnel is uniform and almost steady.
A small model SWEC with two blade sets of 23 cm diameter and a varying distance between the blade sets of 7–54 cm has been built and tested over a range of operating conditions. In order to introduce some degree of uniformity into the way in which users of the wind tunnel record their data, an instrumentation system to measure and display a number of variables that are normally required for all experiments was installed. Two guide rails were used to hold the SWEC inside wind tunnel floor along the centreline using a steel mounting system. The steel mounting system ensured that the system did not move during testing. Measuring sensors were mounted at different locations of the setup. The upwind and downwind velocities are measured by pitot tubes, which use Bernoulli’s principle to convert pressure to velocity readings. The tubes are attached to 2 sensors to convert pressure in volts to velocities in m/s. For measuring the rotational speed of the rotor, two infrared detector and emitter units (photogate sensors) were used. They were mounted behind the rotor.
Measurement depends largely on a data acquisition system utilizing electronic measuring to read instantaneous power produced by the generating system, as various parameters are varied on the turbine or in the environment. The parameters varied include the distance between the two sets of blades, blade profiles, number of blades, wind speeds, and size ratios. To accomplish the objective of this test, three aspects of experimental setup are needed: mechanical, electrical, and measurement software.
All sensors are powered, grounded, and connected to the data acquisition board. All wires are shielded for protection against noise. Measurements are monitored directly and instantaneously in the Graphical User Interface (GUI) of LabView. The user enters numerical values of the blade distance, blade pitch, and blade diameter for the front and back and the relative humidity and temperature. The circuit has 5 sets of measurements on both the front and the back of the generating system. The voltages are measured directly from the potentiometers; these are the total voltages of the circuits. The currents are obtained by measuring the voltages from fixed resistors and dividing that by the resistance. The power is the product of the voltage and the calculated current. The rpm signals go through a frequency measurement tool in LabView and are then multiplied by 60 to obtain the angular velocity in revolutions per minute (rpm). All lines of measurements are connected to the National Instruments Data Acquisition Board NIDAQ USB-6210. Each line is connected to an analog pin which is fed into the LabView program with a USB connection to the computer.
At the beginning of the measurement process, all sensors were checked and calibrated. The pitot tubes are corrected by the offset values to give zero when there is no wind in the tunnel. When starting the program, a path is requested for an Excel file to record the data.
The main factor which characterizes the wind turbine is its power curve, which is defined as a table of data, consisting of connected values of net electric power from the wind turbine and the wind speed. The net electric power from the electric generator is calculated using loss separation
The output power (
Choosing a rotor with the optimal aerodynamic characteristics is a significant step in the design of the SWEC. However, all this will be for nothing if the electrical side of the system is inadequately thoughtout. Based on the maximum speed expected for the SWEC and taking into consideration the cubic relationship between the wind speed and the generated power, the designer must select the generator to match these requirements. The generator can be either fixed or variable speed. Fixed speed generators, like the synchronous machines, operate at speed dictated by the frequency of operation and the number of magnetic poles. Therefore, they are not ideal for wind systems because wind speed is variable. Variable speed generators include DC generators and induction generators. Of the two variable-speed generators, the DC generator is generally used for stand-alone systems, while the induction generator (squirrel cage and wound rotor) is most widely used in applications that supply electricity directly to the grid. For the experimental SWEC setup, two small laboratory-based permanent-magnet machines (18 V; 400 W; 21000 rpm) were used as a generating unit.
Power production tests were conducted with a contrarotating blade system as well as single-rotor system. The testing procedure is conducted to experimentally determine power curves for each blade set and generator at various wind speeds. The maximum power for the corresponding wind speed was calculated using the power equation. For the single-rotor results, the other blade set of the SWEC prototype was taken off. Tests were conducted at the wind tunnel by increasing the wind speed from 14 to 29 m/s in increments of 3 m/s. To test the efficiency of these blades, the peak power extracted from the wind was taken for both sets of blades. Both blade sets produced approximately the same amount of power with the back blade set producing slightly less power than the front set at low and high wind speeds. The results of the measurements have produced the necessary data for the evaluation of the rotor blade performance.
In general, results of the wind tunnel test indicated that a scaled-down version of the contrarotating SWEC may produce up to 60% more energy than a single-rotor system of the same type (Figure
Comparison of power output between single- and contrarotating system.
Effect of wind speed on output power.
Aerodynamic studies are available largely for flows with Reynolds number greater than 106 (Reynolds number is approximately
Effect of Reynolds number on output power.
Understanding of the turbulent properties of wind turbine wakes under different inflow and surface conditions is important to maximize the energy production and ensure the structural reliability of the wind turbines. The structure of wind turbines is known to be affected by the characteristics of the incoming flow. For example, Sheinman and Rosen [
Unwanted turbulence is usually generated in the wind tunnel at the wall (shear stress), at bends of the tunnel (secondary flows), on the model (vortex shedding), and by the fan. To minimize unwanted turbulence, walls should be smooth and carefully sealed, sudden changes in geometry should be avoided, and contraction before the measuring section may increase the mean velocity and decrease the relative turbulence. The most important feature for minimising the turbulence level is the contraction ratio, that is, the ratio of the cross-sectional areas at the wide and narrow ends of the contraction.
Experimentally, we inserted three types of screens (Figure
Three types of screens used in the wind tunnel.
Holes in the above screen are 19 mm × 19 mm (small)
Holes in the above screen are 38 mm × 38 mm (medium)
Holes in the above screen are 76 mm × 76 mm (large)
Output power as a function of screen type.
Flow visualization illustrates the flow on or near an object. It may provide important information on processes which are associated with many problems of fluid flow. In gases, flow visualization is usually accomplished by injection of smoke. Various ways of producing smoke for this purpose have been developed. Although it is not difficult to develop a short-time duration smoke generator, certain problems are encountered when a long-duration smoke of a constant production rate is required. Several techniques are available in literature; however, they cannot be used without “trial and error” approach [
The technique used in this investigation provides long-time duration smoke that forms a plane of closely spaced parallel streak lines. The developed smoke-generating system comprised of compressed air that is ducted through a jar containing a mixture of titanium tetrachloride and carbon tetrachloride and a smoke-dispensing rake. As a result of a chemical reaction and due to the presence of moisture in the air, a dense white smoke (titanium dioxide) is produced. The smoke is supplied through flexible tubing to a brass rake located in the wind tunnel. Smoke jets, approximately 0.0016 m in diameter, are generated downstream of the rake. A honeycomb is placed very close downstream from the rake in order to attenuate disturbances present in the streaklines of the generated smoke.
We used a high speed still-picture camera from HSI Inc. to monitor the fluid visualization in the turbulent wake and for the flow shape around the blades. A white, then black background was used for the back rectangular window, but the effects were not clear. Two 500 W lights with attached reflectors were placed behind the camera, projecting light into the prototype setup, behind the plexiglass of the tunnel window.
Figure
Four camera shots of smoke visualization of a contrarotating SWEC in wind tunnel.
The flow visualization technique described above proved to be effective for qualitative analysis of flow situations. The contrarotating system provides long-time duration, almost stable smoke streaklines, and is easy to operate and maintain.
Combining several or all of the advancements in wind energy technologies makes wind energy systems more efficient; capable to operate at lower wind speeds and keeping up performance, and quieter with gears of reduced noise and better torque transmission efficiency. The following conclusions emerge from this study. The literature indicates that a contrarotating wind energy system could extract additional 20–40% power compared to a single-rotor system from the same wind stream. In this paper, the dependence of the aerodynamic performance of the SWEC on rotor system geometry has been studied by a small-scale model experiment in the wind tunnel. Test results indicate that a contrarotating system may produce up to 60% more energy than a single-rotor system of the same type and is capable to reduce cut-in speed while keeping up performance. In addition to energy conversion efficiency, the main problem that the contrarotating concept solves is improved performance in low-wind conditions.
Although the SWEC under development has great potential, it still needs further studies, including the design of blade construction; the optimization between the rotor and electric generator; power efficiency, power quality, and power factor; and the static and transient stability of the system. In future, the percentage of wind energy on many grids is expected to be a significant part, especially from SWECs thus making them as key grid players. However, these machines still require the best technologies from various disciplines to behave like power plants. The success of SWECs depends strongly on their ability to comply with both efficiency expectations and the requirements of grid utilities. An introductory video about the SWEC under development is available [
Financial support from the University of Ottawa and Ontario Centres of Excellence (OCE) is gratefully acknowledged. Advice and suggestions during the measurement program and data analysis activities from Professor Stavros Tavoularis of the University of Ottawa’s Department of Mechanical Engineering are appreciated.