ISRN OpticsVolume 2012 (2012), Article ID 243672, 5 pagesdoi:10.5402/2012/243672

Research Article

Comparative Analysis of Free Optical Vibration of Lamination Composite Optical Beams Using the Boubaker Polynomials Expansion Scheme and the Differential Quadrature Method

Uğur Yücel,¹ Emna Gargouri-Ellouze,² Karem Boubaker,³ Gökmen Atlıhan,⁴ Hasan Çallıoğlu,⁴ E. Sahin Conkur,⁴ Ahmet Gökdoğan,⁵ Mehmet Merdan,⁶ Muzaffer Topcu,⁴ N. Sher Akbar,⁷ S. Nadeem,³ and Ahmet Yıldırım⁵

¹Department of Mathematics, Faculty of Science and Letters, Pamukkale University, 20020 Denizli, Turkey²Institut Supérieur des Etudes Technologiques de Radès, 2098 Tunis, Tunisia³Equipe de Physique des Dispositifs à Semiconducteurs, Faculté des Sciences de Tunis, Campus Universitaire, 2092 Tunis, Tunisia⁴Department of Mechanical Engineering, Pamukkale University, 20017 Denizli, Turkey⁵Department of Software Engineering, Faculty of Engineering, Gümüşhane University, 29100 Gümüşhane, Turkey⁶Department of Geomatic Engineering, Faculty of Engineering, Gümüşhane University, 29100 Gümüşhane, Turkey⁷Department of Mathematics, Quaid-i-Azam University, Islamabad 45320, Pakistan

Received 22 November 2011; Accepted 4 January 2012

Academic Editor: D. H. Woo

Copyright © 2012 Uğur Yücel et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

The effects of stacking sequences of composite laminated optical beams on free vibration frequencies are investigated using two methods: the Boubaker Polynomials Expansion Scheme (pbes) and the Differential Quadrature Method (dqm). In the last decades, these two techniques have been separately performed for obtaining accurate numerical solutions to several initial boundary value problems (Vo et al. 2010, Li et al. 2008, Chen 2003, Hu et al. 2008, Karami et al. 2003, Malekzadeh et al. 2004, Khare et al. 2004, Della and Shu 2005, Ramtekkar et al. 2002, Adam 2003). Conjointly yielded results are compared and discussed.

1. Introduction

Free optical vibration of generally laminated beams has been of increasing interest in the last decades’ literature [1–12]. Vo et al. [1] investigated free vibration of axially loaded thin-walled composite beams with arbitrary lay-ups. The proposed model was based on equations of motion for flexural-torsional coupled vibration which were derived from the Hamilton’s principle. In the same context, Li et al. [2] studied the free vibration and buckling behaviors of axially loaded laminated composite beams using the dynamic stiffness method. The model took into account influences of axial force, Poisson effect, axial deformation, shear deformation, and rotary inertia. Hu et al. [4] Karami et al. [5], and Malekzadeh et al. [6] proposed a differential quadrature element method (DQEM) by using Hamilton’s principle for free vibration analysis of arbitrary nonuniform Timoshenko beams on elastic supports.

Many other analytical methods of analysis have been used to study the vibration of plates, shells, and beams [7–12].

In this paper, a model on the vibration analysis of laminated composite beam has been developed and studied using two resolution protocols. For the beam used, it is assumed that Bernoulli-Euler hypothesis is valid. The results obtained by the two methods are compared. It has been concluded that all of the results are very close to each other.

2. Problem Formalization

The normal stress in th layer of a composite laminated beam shown in Figure 1 can be written in the following way: According to Bernoulli-Euler hypotheses, the deformation at a certain distance from neutral plane is where is the curvature of the beam. The relationship between normal stress and bending moment is given by or where and are the height and the width of the beam, is the number of layer and is the distance between the outer face of th layer, and the neutral plane. The relationship between the bending moment and the curvature can be written as follows: where is the effective elasticity modulus and is the cross-sectional inertia moment of the beam. Flexural motion of a linear elastic laminated composite beam without shear or rotary inertia effects is described by Bernoulli-Euler equation: As a solution of (6), it can be used a separation of variables solution for harmonic free vibration: where is the frequency and   is the mode shape function of the lateral deflection. Substitution of this solution into (6) eliminates the time dependency and yields the following characteristic value problem: where is the dimensionless frequency of the beam vibrations given by For a cantilever composite laminated beam shown in Figure 1, the boundary conditions at the two ends are due to the deflection and rotation both being zero at the clamped end, and due to the bending moment and shear force both vanishing at the free end.

Figure 1: Cantilever composite laminated optical beam.

The analytical solution of (8) subjected to (10) and (11) yields the frequency equation: which may be found in the relevant literature [13].

3. DQM Solution

DQM method is carried out for the approximate solution of the characteristic value problem in (8) with the boundary conditions given by (10) and (11) by first discretizing the interval such that , where is the number of grid points. Application of the DQM to discrete the derivative in (8) leads to where are the weighting coefficients of the fourth-order derivative which can be calculated using the explicit relations given by Shu [14]. Note that we have two boundary conditions specified at both ends. These two conditions at the same point provoke a great challenge for the DQM, because we have only one quadrature equation at one point in the DQM, which prevents implementing the two boundary conditions. We use -point technique to eliminate the difficulties in implementing two conditions at a single boundary point (Figure 2). Following the same approach presented in [15], the boundary conditions at can be discretized as Similarly, the boundary conditions at can be discretized as The assembly of (13) through (15) yields the following set [14] of linear equations: where the subscripts and indicate the grid points used for writing the quadrature analog of boundary conditions and the governing differential equation, respectively. By matrix substructuring of (17), one has the following two equations: From the first part of (18), one obtains Back-substituting (19) into the second part of (18), one gets where is of order and given by Both the eigenvalues being the frequency squared values and the eigenvectors describing the mode shapes of the freely vibrating beam may be obtained simultaneously from the matrix.

Figure 2: A one-dimensional quadrature grid with adjacent -points.

4. BPES Solution

The BPES [16–23] is applied to (8) through setting the expression where are the -order Boubaker polynomials, is the normalized time, are minimal positive roots, is a prefixed integer, and are unknown pondering real coefficients.

Consequently, it comes for (8) that The related boundary conditions expressed through (10) and (12). The BPES protocol ensures their validity regardless main equation features. In fact, thanks to Boubaker polynomials first derivatives properties are Boundary conditions are inherently verified: The BPES solution is obtained through five steps:(i)Integrating, for a given value of , the whole expression given by (23) along the interval .(ii)Determining the set of coefficients where that minimizes the absolute difference : (iii)Deducing the corresponding frequency using (9).(iv)Incrementing .(v) Ranging the obtained frequencies.

5. Results and Discussion

Natural frequencies of the symmetric laminated composite cantilever beam have been estimated using the Boubaker Polynomials Expansion Scheme (PBES) and the Differential Quadrature Method (DQM), and for parameters values indicated in Table 1. Figure 3 presents the obtained values. The results have been evaluated as quite close to each other.

Table 1: Geometry and material properties of the composite materials.

Descriptions
Present
Unit

(mm)
320
mm

(mm)
36
mm

(mm)
8
mm

(MPa)
26950
MPa

(MPa)
21800
MPa

(MPa)
7540
MPa

0.15

(kg/m³)
2030
kg/m³

Figure 3: Comparison of BPES and DQM frequencies for cross-ply laminated beam.

The natural frequency alteration as a direct result of the change in the stacking sequence causes resonance if the changed frequency becomes closer to the working frequency. Hence, selection of the stacking sequences in the laminated composite beams has to be outlined.

6. Conclusion

This work deals with two protocols for the calculation of natural frequency of the symmetric laminated composite cantilever beam. Calculations performed by means of Boubaker Polynomials Expansion Scheme PBES and Differential Quadrature Method DQM yielded coherent and similar results.

All considered results have been seen to be in accordance with each other. Changes in the stacking sequence, which likely allow tailoring of the material to achieve desired natural frequencies and respective mode shapes without changing its geometry, are the subject of following studies.

References

T. P. Vo, J. Lee, and K. Lee, “On triply coupled vibrations of axially loaded thin-walled composite beams,” Computers and Structures, vol. 88, no. 3-4, pp. 144–153, 2010.

J. Li, H. Hua, and R. Shen, “Dynamic stiffness analysis for free vibrations of axially loaded laminated composite beams,” Composite Structures, vol. 84, no. 1, pp. 87–98, 2008.

C. N. Chen, “Buckling equilibrium equations of arbitrarily loaded nonprismatic composite beams and the DQEM buckling analysis using EDQ,” Applied Mathematical Modelling, vol. 27, no. 1, pp. 27–46, 2003.

Y. J. Hu, Y. Y. Zhu, and C. J. Cheng, “DQEM for large deformation analysis of structures with discontinuity conditions and initial displacements,” Engineering Structures, vol. 30, no. 5, pp. 1473–1487, 2008.

G. Karami, P. Malekzadeh, and S. A. Shahpari, “A DQEM for vibration of shear deformable nonuniform beams with general boundary conditions,” Engineering Structures, vol. 25, no. 9, pp. 1169–1178, 2003.

P. Malekzadeh, G. Karami, and M. Farid, “A semi-analytical DQEM for free vibration analysis of thick plates with two opposite edges simply supported,” Computer Methods in Applied Mechanics and Engineering, vol. 193, no. 45-47, pp. 4781–4796, 2004.

R. K. Khare, T. Kant, and A. K. Garg, “Free vibration of composite and sandwich laminates with a higher-order facet shell element,” Composite Structures, vol. 65, no. 3-4, pp. 405–418, 2004.

C. N. Della and D. Shu, “Free vibration analysis of composite beams with overlapping delaminations,” European Journal of Mechanics, A/Solids, vol. 24, no. 3, pp. 491–503, 2005.

G. S. Ramtekkar, Y. M. Desai, and A. H. Shah, “Natural vibrations of laminated composite beams by using mixed finite element modelling,” Journal of Sound and Vibration, vol. 257, no. 4, pp. 635–651, 2002.

C. Adam, “Moderately large flexural vibrations of composite plates with thick layers,” International Journal of Solids and Structures, vol. 40, no. 16, pp. 4153–4166, 2003.

M. Kisa, “Free vibration analysis of a cantilever composite beam with multiple cracks,” Composites Science and Technology, vol. 64, no. 9, pp. 1391–1402, 2004.

M. Kisa, J. Brandon, and M. Topcu, “Free vibration analysis of cracked beams by a combination of finite elements and component mode synthesis methods,” Computers and Structures, vol. 67, no. 4, pp. 215–223, 1998.

L. Meirovitch, Element of Vibration Analysis, McGraw-Hill, New York, NY, USA, 1986.

C. Shu, Differential Quadrature and Its Application in Engineering, Springer, London, UK, 2000.

C. W. Bert and M. Malik, “Differential quadrature method in computational mechanics: a review,” Applied Mechanics Reviews, vol. 49, no. 1, pp. 1–27, 1996.

J. Ghanouchi, H. Labiadh, and K. Boubaker, “An attempt to solve the heat transfer equation in a model of pyrolysis spray using 4q-order m-boubaker polynomials,” International Journal of Heat and Technology, vol. 26, no. 1, pp. 49–53, 2008.

O. B. Awojoyogbe and K. Boubaker, “A solution to Bloch NMR flow equations for the analysis of hemodynamic functions of blood flow system using m-Boubaker polynomials,” Current Applied Physics, vol. 9, no. 1, pp. 278–283, 2009.

H. Labiadh and K. Boubaker, “A Sturm-Liouville shaped characteristic differential equation as a guide to establish a quasi-polynomial expression to the Boubaker polynomials,” Differential Equations and Control Processes, vol. 2, no. 2, pp. 117–133, 2007.

S. Slama, J. Bessrour, M. Bouhafs, and K. B. B. Mahmoud, “Numerical distribution of temperature as a guide to investigation of melting point maximal front spatial evolution during resistance spot welding using boubaker polynomials,” Numerical Heat Transfer; Part A, vol. 55, no. 4, pp. 401–408, 2009.

S. Slama, M. Bouhafs, and K. B. Ben Mahmoud, “A boubaker polynomials solution to heat equation for monitoring A3 point evolution during resistance spot welding,” International Journal of Heat and Technology, vol. 26, no. 2, pp. 141–145, 2008.

S. A. H. A. E. Tabatabaei, T. Zhao, O. B. Awojoyogbe, and F. O. Moses, “Cut-off cooling velocity profiling inside a keyhole model using the Boubaker polynomials expansion scheme,” International Journal of Heat and Mass Transfer, vol. 45, no. 10, pp. 1247–1251, 2009.

S. Fridjine and M. Amlouk, “A new parameter: an abacus for optimizing PVT hybrid solar device functional materials using the boubaker polynomials expansion scheme,” Modern Physics Letters B, vol. 23, no. 17, pp. 2179–2191, 2009.

A. Belhadj, J. Bessrour, M. Bouhafs, and L. Barrallier, “Experimental and theoretical cooling velocity profile inside laser welded metals using keyhole approximation and Boubaker polynomials expansion,” Journal of Thermal Analysis and Calorimetry, vol. 97, no. 3, pp. 911–915, 2009.