Material Handling Equipment Selection UsingWeighted Utility Additive Theory

�etter utilization of manpower, providing product �exibility, increasing productivity, decreasing lead time, reduction in handling cost, increased efficiency ofmaterial �ow, and enhancement of production process are someof themost important issues in�uencing material handling (MH) equipment selection decision. As a wide variety ofMH equipment is available today, selection of the proper equipment for a designed manufacturing system is a complicated task. Selection of suitable MH equipment for a typical handling environment is found to be amulticriteria decision-making (MCDM)problem.As the selection process is found to be unstructured, characterized by domain dependent knowledge, there is a need to apply an efficient MCDM tool to select the most suitable MH equipment for the given application. is paper applies weighted utility additive (WUTA) method to solve an MH equipment selection problem. e ranking obtained using the WUTA method is compared with that derived by the past researchers which proves its potentiality, applicability, and accuracy to solve complex decision-making problems.


Introduction
Material handling (MH) is an activity that uses the right method to provide the right amount of the right material at the right place, at the right time, in the right sequence, in the right position, and at the right cost [1].An MH system is responsible for transporting materials between workstations with minimum obstruction and joins all the workstations and workshops in a manufacturing system by acting as a basic integrator.e MH task accounts for 30-75% of the total cost of a product, and efficient MH can be responsible for reducing the manufacturing system operations cost by 15-30% [2].ese �gures justify the importance of MH cost as an element in improving the cost structure of a manufacturing organization.An efficient MH system greatly improves the competitiveness of a product through the reduction of handling cost, enhances the production process, increases production and system �exibility, increases efficiency of material �ow, improves facility utilization, provides effective utilization of manpower, and decreases lead time [3].e functions performed by MH equipment can be classi�ed into four broad categories, that is, (a) transport, (b) positioning, (c) unit formation, and (d) storage.Usually, all the MH functions are composed of one or more combinations of these four primary functions.Equipment in transport category simply moves materials from one point to another, which includes conveyors, industrial trucks, cranes, and so forth.Unlike transport equipment, positioning equipment is usually employed at workstations to aid machining operations.Robots, index tables, rotary tables, and so forth are the examples of this type of equipment.Unit formation equipment is used for holding or carrying materials in standardized unit load forms for transport and storage and generally includes bins, pallets, skids, and containers.Storage equipment is used for holding or buffering materials over a period of time.Typical examples that perform this function are AS/RS, pallet racks, and shelves.
e MH equipment selection is an important function in the design of an MH system and, thus, a crucial step for facility planning.e determination of an MH system involves both the selection of suitable MH equipment and the assignment of MH operations to each individual piece of equipment.As a wide variety of equipment is available today, each having distinct characteristics and cost that distinguish from others, selection of the proper equipment for a designed manufacturing system is a very complicated task and is oen in�uenced by the ongoing development of new technology, practices, and equipment.While choosing the best MH equipment, the successful solution would likely involve matching the best solution with the existing or contemplated physical facilities and environment.e major factors contributing to the complexity of MH selection process are constraints imposed by the facility and materials, multiple con�icting design criteria, uncertainty in the operational environment, and the wide variety of equipment types and models available.
When implementing a new MH equipment, the decision makers are faced with the following issues, that is, (a) selection of an MH equipment that would give the desired bene�ts to the manufacturing organization with due consideration to its objectives and operating characteristics, (b) �nancial justi�cation of the investment, and (c) development of a plan to ensure that the set objectives are met when the selected MH equipment is implemented and evaluated.For these reasons, the decision makers have to consider various quantitative (load capacity, energy consumption, reliability, cost, etc.) and qualitative (�exibility, performance, environmental hazard, safety, load shape, load type, etc.) criteria.On the other hand, some of the selection criteria are bene�cial (higher values are preferred) and some are nonbene�cial (lower values are desired).erefore, MH equipment selection can be viewed as a multicriteria decision-making (MCDM) problem in the presence of many con�icting criteria.
As the MH equipment selection is a difficult and knowledge intensive process, various mathematical tools can be effectively applied to solve this problem.However, it is always observed that the evaluation criteria involved in MH equipment selection problems have contradictory effects on the performance of the alternatives, are versatile in nature, and oen expressed in different units with varying ranges.erefore, a strong and unprejudiced mathematical model is essential for selection of the most appropriate MH equipment for a given industrial application.e weighted utility additive (WUTA) method having a sound mathematical background, ability to incorporate preferences for the selection criteria, and competency to handle mixed (cardinal and ordinal) data is a perfect choice to rank and select the best suited MH equipment.In this method, the reference ranking of the alternatives is formulated, and the indifference as well as preference relations between the alternatives are utilized for ranking purpose, deriving almost accurate results.It enhances the strengths of the conventional utility additive (UTA) method by incorporating criteria weights, which are usually observed as essential for solving the decision-making problems.us, the aim of this paper is set to show the viability of the WUTA method to solve decision-making problems with any number of selection criteria and candidate alternatives, with special emphasis on MH equipment selection.It is a variant of UTA family of models.e effectiveness and solution accuracy of any MCDM method can only be validated by comparing the derived rankings with those obtained by the earlier researchers.Here, the rank orderings of the alternatives derived by the past researchers act like some benchmarks.e cited example, already solved using different MCDM methods for ranking of MH equipment alternatives, thus provides sufficient ground for comparison of the performance of the proposed WUTA method.

Literature Review
Since 1990s, research concentrating on the selection and assignment of MH equipment has been carried out, and signi�cant achievements have been attained.Chakraborty and Banik [4] applied analytic hierarchy process (AHP) for selecting the best MH equipment under a speci�c handling environment.e relative importance of each criteria and subcriteria was measured using pair-wise comparison matrices, and the overall rankings of all the alternative equipment were then determined.To identify the most critical and robust criteria in the MH equipment selection process, sensitivity analysis was also performed.Sujono and Lashkari [5] proposed a method for simultaneously determining the operation allocation and MH system selection in a �exible manufacturing environment with multiple performance objectives.A 0-1 integer programming model was developed to select machines, assign operations of part types to the selected machines, allocate MH equipment to transport the parts from machine to machine, and as to handle the part at a given machine.Onut et al. [6] proposed an integrated fuzzy analytic network process (F-ANP) and fuzzy technique for order performance by similarity to ideal solution (F-TOPSIS) methodology for evaluating and selecting the most suitable MH equipment types for a manufacturing organization.Komljenovic and Kecojevic [7] applied coefficient of technical level and AHP methods for selection of rail-mounted boom type bucket wheel reclaimers and stacker-reclaimers as used for material handling at the stockyards.Tuzkaya et al. [8] suggested an integrated F-ANP and fuzzy preference ranking organization method for enrichment evaluation (F-PROMETHEE) approach for solving the MH equipment selection problems.Sawant et al. [9] applied preference selection index (PSI) method to choose automated guided vehicle (AGV) in a given manufacturing environment.An AGV selection index was proposed to evaluate and rank the considered alternatives.Maniya and Bhatt [10] used AHP to assign the relative importance between different AGV selection criteria and then applied modi�ed grey relational analysis (M-GRA) method to determine the corresponding index values for AGV selection.
On the other hand, some researchers have attempted to develop knowledge-based systems for proper selection of equipment used for varying handling tasks.Welgama and Gibson [11] proposed a methodology for automating the selection of an MH system while combining the knowledgebase and optimization approaches.Chu et al. [12] developed a microcomputer-based system called "ADVISOR" to help user to design, select, and evaluate the proper MH equipment for a production shop.Chan et al. [13] proposed an intelligent MH equipment selection advisor (MHESA), composed of a database to store equipment types with their speci�cations, knowledge-based expert system for assisting MH equipment selection, and an AHP model to choose the most appropriate MH equipment.Yaman [14] described a knowledge-based approach for MH equipment selection and re-design of equipment in a given facility layout.Fonseca et al. [15] developed a prototype expert system for industrial conveyor selection which would provide the user with a list of conveyor solutions for their MH needs along with a list of suppliers for the suggested conveyors.Conveyor types were selected on the basis of a suitability score, which was a measure of the ful�llment of MH requirements by the characteristics of the conveyor.Kulak [2] developed a fuzzy multiattribute MH equipment selection system consisting of a database, a rulebased system, and multiattribute decision-making modules.A fuzzy information axiom approach was also introduced and used in the selection of MH equipment in a real case.Cho and Edbelu [16] developed a web-based system, called as "DESIGNER" for the design of integrated MH systems in a manufacturing environment, which could model and automate the MH system design process, including the selection of MH equipment.Mirhosseyni and Webb [17] presented a hybrid method for selection and assignment of the most appropriate MH equipment.At �rst, the system would select the most appropriate MH equipment type for every MH operation in a given application using a fuzzy knowledge-based expert system, and in the second phase, a genetic algorithm would search throughout the feasible solution space, constituting of all possible combinations of the feasible equipment speci�ed in the previous phase, in order to discover the optimal solution.e main disadvantage of the knowledge-based expert systems is that, in these approaches, as the set rules are static in nature and domain-speci�c, it is very difficult for the decision makers to know how the decision for the best MH equipment has been arrived.

The WUTA Method
e WUTA method which is an extension of the UTA approach, proposed by Jacquet-Lagreze and Siskos [18], aims at inferring one or more additive value functions from a given ranking on reference set,   .In MCDM problems, the decision makers usually consider a set of alternatives, called A, which is valued by a family of criteria,    1 ,  2 , … ,   ).A classical operational attitude of assessing a model of overall preference of the decision makers leads to the aggregation of all the criteria into a unique criterion, called a utility function ()).
1 ,  2 , … ,    . ( Let  be the strict preference where     ) is the marginal utility of the attribute,   for the given alternative.When different weight values (relative importance) are assigned to the attributes, the weighted utility function can be expressed as follows: where     )        ), and   is the weight for th attribute.Again, for alternative ", " (4) can be written as Now,  +  and  −  , respectively, denote the most and the least preferred value of th attribute.e most common normalization constraints using the additive form of (4) are as follows: On the basis of the additive model, as shown in ( 5) and taking into account the preference conditions, the value of each alternative,     can be written as follows: where )  0 is a potential error relative to the utility.
To estimate the marginal value functions in a piecewise linear approach, a linear interpolation method is proposed [18][19][20] then one of the following relationships holds: where  is a small positive number to discriminate signi�cantly two successive equivalence classes of .e marginal value functions are �nally estimated using the following linear program (LP), in which the objective function depends on (), indicating the amount of total deviation.
is LP model is solved to obtain the marginal utility values.en, the utility value ([()]) for each alternative is calculated.e higher the [()] value, the better the alternative.
It is observed that the WUTA method generally copes well with noisy or inconsistent data [21], it is least sensitive to changes in preferences for the considered criteria, and it is not as time consuming, redundant, and boring as the other MCDM methods where the decision makers have to de�ne certain preference functions to evaluate the superiority of one alternative over the other.is method is based on two fundamental concessions; that is, (a) it does not allow any situation of incomparability between two alternatives, and (b) it addresses the evaluation (assessment) problem in a synthesizing, exhaustive, and de�nite way.It has also several interesting features, like it makes possible estimation of a nonlinear additive function which is obtained by the use of a linear program that provides convenient piecewise linear approximation of the function, and the only information required from the decision makers is the global stated preferences between different alternatives of the reference set.It also perfectly �ts in those situations where there are difficulties in directly obtaining from the users the values of the preference model.
Generally, the data available for various criteria in a decision-making problem are expressed in different dimensional units with varying ranges.In order to eradicate these effects, it is required to normalize the criteria values within a range of 0 to 1. On the contrary, if criteria values are not normalized, those criteria with higher weights will be more prone to affect the �nal ranking of the alternatives.In case of nonnormalized data, the change in unit for a particular criterion will directly affect the values of the weighted decision matrix, which will ultimately have an effect on the ranking of the alternatives.In order to consider the effects of higher and lower preferences of bene�cial and non-bene�cial criteria in a decision-making problem, they have to be treated separately, which is taken into care in the normalization procedure.In the WUTA method, if the criteria values are not normalized, all the criteria will be treated as bene�cial because in this method, the �nal ranking of the alternatives is based on the reference ranking, which is obtained by adding the weighted normalized criteria values.

Illustrative Example
In order to illustrate and validate the applicability of the WUTA method for solving MH equipment selection problems, a real time example considering the selection of a conveyor [2] is cited here.e �nal ranking of the alternative MH equipment as obtained using the WUTA method is also compared with that derived by the past researchers.
is MH equipment selection problem is aimed to determine the most appropriate conveyor among the alternatives of the same type.e related objective and subjective data of the attributes are given in Table 1 [2].e attributes considered are �xed cost per hour (�C), variable cost per hour (VC), speed of conveyor (SC), item width (IW), item weight (W), and �exibility (�).Among those six attributes, �exibility was de�ned subjectively.Rao [22] converted the linguistic terms for �exibility criterion into corresponding fuzzy scores, and appropriate objective values were subsequently assigned.e conveyor should have low �xed and variable costs, higher speed, ability to handle large item widths and weights, and have higher �exibility.�C and VC are nonbene�cial attributes (where lower values are desired), and the remaining four attributes are considered as bene�cial (where higher values are preferred).
Rao [22] considered equal weights for all the six criteria and obtained the best and the worst choices as conveyor 3 and conveyor 1, respectively, while solving this problem using simple additive weighting (SAW), weighted product method (WPM), AHP, graph theory and matrix approach (GTMA), TOPSIS and modi�ed TOPSIS methods.Giving equal weights to the considered criteria may sometimes lead to wrong and biased decisions.Hence, the criteria weights are recalculated here using AHP method, as shown in Table 2, and are used for subsequent WUTA method-based analysis.For solving this problem using the WUTA method, the criteria values of Table 1 are �rst normalized using the following equations.
For bene�cial attribute: For nonbene�cial attribute: where   is the performance of th alternative with respect to th criterion, and   is the normalized value of   .en, the weighted normalized criteria values (  ) are obtained using the following expression: e normalized and weighted normalized decision matrices are given in Tables 3 and 4, respectively.
From the ∑   values, the reference sequence (  ) for the alternative conveyors is observed as  3 −  2 −  1 −  4 .Now, the range [ −    +  ] for each conveyor selection criterion is divided into equal intervals.e number of intervals and the interval difference for each criterion, as calculated using (8), with their corresponding  −  and  +  values are given in Table 5. e number of intervals (  ) is selected in such a way that the interval for each criterion is almost equal.However, a large number of intervals may cause an increase in the computational complexity as well as time.In order to minimize the computation time, a minimum possible number of intervals is selected here, so that the �nal results are not affected.For example, in case of "VC" criterion, the value for the number of intervals is chosen as 2 because it has the lowest range between [ −  ,  +  ].As the criteria "FC", "SC", and "F" have ranges close to that for "VC" criterion, the same number of intervals is also selected for those criteria.On the other hand, for "IW" and "W" criteria, the number of intervals is selected as 3 for their wider ranges.Now, we have the following set of equations.
For attribute FC: For attribute VC: For attribute SC: For attribute IW: For attribute W: For attribute F: Now, aer solving the above set of equations using (9), the following results are derived.For alternative  1 : Now, the utility values for all the four alternatives are calculated using (7) and are shown below: As the optimal solution of the objective function in the LP problem results in a zero value, the utility functions are perfectly compatible with the reference sequence.Aer arranging these utility values in descending order, the �nal ranking of the four conveyors is  3 −  2 −  1 −  4 , suggesting that  3 is the best conveyor among the considered alternatives, followed by  2 . 4 is the worst choice.Rao [22] also obtained  3 as the best choice and a total ranking for the conveyors as  3 −  2 −  4 −  1 .e Spearman's rank correlation coefficient (  ) between these two rank orderings is calculated as 0.8, which represents the capability of the WUTA method for solving this conveyor selection problem.
Oen the criteria weights in MCDM problems are challenged because of assortment and uncertainty involved in their calculations.erefore, in order to deal with this issue, a sensitivity analysis is performed to study the impact of different criteria weights on the �nal ranking of the alternative conveyors.In this example, the weights for "IW" and "W" criteria are maximum, and hence, they are selected for increasing and decreasing their values in steps on either side.e weights of these two criteria are subsequently changed by −25%, −10%, +10%, and +25% in steps, and the weights of the remaining criteria are equally adjusted, so that the sum of all the criteria weights must add up to one.e results of this sensitivity analysis are exhibited in Table 6.It is observed from this table that changes in weights of the two most important criteria by +10%, +25%, and −10% do not show any variation in the �nal rankings of the alternative conveyors, but when the weights of the two selected criteria are changed by −25%, the positions of the last two alternative conveyors are just reversed.In all the cases, the best chosen conveyor remains unaffected.is result proves the robustness of the WUTA method for solving such types of MCDM problems.
Table 7 compares the rankings of the alternative conveyors as obtained by WUTA and other popular MCDM methods, like VIKOR (VIse Kriterijumska Optimizacija kompromisno Resenje), PROMETHEE, and ELECTRE (ELimination and Et Choice Translating Reality).ese derived rankings are also compared with those obtained by Kulak [2] and Rao [22].Kulak [2] developed a decision support system (FUMAHES: fuzzy multiattribute material handling equipment selection), and Rao [22] mainly applied GTMA method for solving this problem.It is observed that in most of the MCDM methods, the best and the least preferred alternative conveyors remain unchanged.Even though, the results obtained using different MCDM methods are quite similar, the WUTA method requires less computational time, as the LP-based mathematical formulations can be quickly solved employing LINDO soware tool.A sound, systematic and logical base for this method provides almost robust rankings for the candidate alternatives as compared to other MCDM methods, which can be judged through the results of sensitivity analysis.In this method, the decision makers need not to perform tedious and repetitive pair-wise comparisons between the performance of different alternatives with respect to each criterion, thus saving computational time.In addition, the results obtained from this method are completely free from inconsistent and biased judgments of the decision makers.us, it may always be expected that this robust method would provide accurate ranking preorders for the alternatives, having minimally affected by the change in criteria weights and decision makers' perceptions.

Conclusions
e problem of selecting the most appropriate MH equipment for a speci�c task is a strategic issue, greatly in�uencing the performance and pro�tability of the manufacturing organizations.is paper presents the use of WUTA method for solving an MH equipment selection problem.It is observed that the WUTA method is a viable tool in solving the MH equipment selection problems.It allows the decision makers to rank the candidate alternatives more efficiently and accurately.As this method has a strong and sound mathematical foundation, it is capable of deriving more accurate ranking of the considered alternatives.It can not only help in just selecting the best MH equipment, but it can also be applied for any decision-making problem with any number of selection criteria and feasible alternatives while offering a more objective and straightforward approach.It is also observed that this method is quite robust against changes in the criteria weights.