Aerogels are solids with high porosity (<100 nm) and hence possess extremely low density (∼0.003 g/cm3) and very low conductivity (∼10 mW/mK). In recent years, aerogels have attracted more and more attention due to their surprising properties and their existing and potential applications in wide range of technological areas. An overview of aerogels and their applications as the building envelope components and respective improvements from an energy efficiency perspective including performance is given here. This overview covers thermal insulation properties of aerogels and studies regarding structural features which will be helpful in buildings envelope. The improvements of thermal insulation systems have future prospects of large savings in primary energy consumption. It can be concluded that aerogels have great potential in a wide range of applications as energy efficient insulation, windows, acoustics, and so forth.
1. Introduction
Short supply, limited availability, and increasing energy costs all around the world emphasize the need for immediate energy conservation in both oil rich and oil producing countries. An effective way towards saving energy is to improve the thermal insulation of buildings especially in hot climates where the energy demand for cooling by air conditioning is comparatively higher. In addition to the need for energy saving, high insulating materials are further justified by improved comfort levels and increased building life. Thermal characteristics depend largely on the thermal conductivity of the cell walls and the cell matrix, as well as radiation and convection, with the cell matrix being the most significant factor in determining the overall heat transfer characteristics. Thermal properties of some commonly available insulating materials are given in Table 1.
Commonly available thermal insulation materials.
S. number
Material
R-value (per inch)
Green
Flammable
Remark
1
Mineral wool
R—3.1
Yes
No
Does not melt or support combustion
2
Fibreglass
R—3.1
Yes
No
Does not absorb water
3
Polystyrene (EPS)
R—4
No
Yes
Is difficult to use around imperfections; can become costly
4
Polyurethane foam
R—6.3
No
Yes
Makes a great sound insulator
5
Cellulose
R—3.7
Yes
Yes
Contains the highest amount of recycled content
Thermal conductivity varies with time due to changes in the composition of the cell matrix. The ambient air and external building surface temperatures in hot climates of Asia and Africa are much higher than in cold climates of a Australia, Europe and America, temperature of 38°C should be taken into account while calculating thermal conductivities at ageing. In addition to the product specific parameter of the change of the thermal conductivity, mean temperature and water absorption are also other important influencing factors.
As per IUPAC, aerogel is defined as a gel comprised of a microporous solid in which dispersed phase is a gas [1]. Aegerter et al. defined aerogels as gels in which the liquid has been replaced with air, with very moderate shrinkage of a solid network [2]. Aerogel is basically a synthetic porous ultralight material derived from a gel, in which the liquid component of the gel has been replaced with a gas; for example, graphene aerogels are so light that they can rest on top of a grass leaf. The combination of high porosity and extremely small pores provides aerogels with their extreme properties: solid with extremely low density and low thermal conductivity [3]. Aerogels are sometimes also known by different names such as frozen smoke, solid smoke, solid air, or blue smoke owing to translucent nature and the way light scatters in the material [4]. Typical structure of an aerogel is shown in Figure 1.
Nanometer scale particles and pores in an aerogel. (a) Network architecture of an aerogel [77]. (b) Electron micrograph of a silica aerogel [78].
Aerogels together with vacuum insulation panels are one of the new promising high performance thermal and acoustic insulation materials for possible building applications and are currently the main market for aerogels, whereas other applications such as absorbents, shock absorbers, nuclear waste storage, batteries, and catalysts are also possible [5–13]. A list of commercial available aerogels with their trade names is given in Table 2.
Commercial aerogel products.
S. number
Product
Applications
References
1
Cabot
(i) Pellets, composites (ii) Day lighting applications (iii) Oil and gas pipeline insulation (iv) Cryoinsulation
[73, 74]
2
Aspen aerogels
(i) Construction materials (ii) Flexible blanket insulation (iii) Oil and gas pipeline (iv) Aerospace, apparel
Aerogels are typically characterized by low density solid, low optical index of refraction, low thermal conductivity, low speed of sound through materials, high surface area, and low dielectric constant.
In this paper authors gave an overview of aerogels and their applications as the building envelope components and respective improvements from an energy efficiency perspective. This covers thermal insulation properties of aerogels and studies regarding structural features which will be helpful in buildings envelope. This overview is presented in two parts: firstly, the general discussion of aerogels regarding how they have such a high thermal quality and what are their physical properties which will be useful in making insulating materials and secondly, their remarkable properties due to extraordinary physical and chemical structure of aerogels.
2. Aerogels
The passage of thermal energy through an insulating material occurs through three mechanisms: solid conductivity, gaseous conductivity, and radiative (infrared) transmission. The sum of these three components gives the total thermal conductivity of the material. Solid conductivity is an intrinsic property of a specific material. The improvement of thermal resistance of the building envelope can be achieved by decreasing the thermal conductivity.
Fricke et al. observed that both the solid conductivity and the gas conductivity were proportional to the density as shown below:
(1)λgas∝ρ-0.6λsolid∝ρ1.5.
Hümmer et al. using these relations derived the following relation for the radiative conductivity, which is a relative equation for the thermal conductivity of opacified silica aerogels:
(2)λtotal(ρ)=λsolid,0(ρρ0)1.5+λgas,0(ρρ0)-0.6+λrad,0(ρρ0)-1(TT0)3,
where ρ (kg/m3) is the density; λtotal, λgas, λsolid, and λrad (W/m.K) are the total conductivity, the conductivity for gas conduction, the conductivity for solid conduction, and the radiative conductivity, respectively; T(K0) is the temperature, and the index 0 means that parameters are related to a reference material from an aerogel [14].
Aerogel is made of more than 90% of air, having extremely low weight, transparency, and excellent thermal conductivity. Aerogel is an ideal material for thermal insulation due to all these properties [15, 16]. Also their high visible solar transmittance (Tvis) is desirable for application in windows. Further decrease in thermal conductivity of aerogel can be observed if evacuated below 50 hPa; thermal conductivity decreased because of elimination of pore gas. Superinsulations with extremely low thermal conductivities can be implemented with evacuated highly porous powder, fiber, or gel spacers. Due to the Knudsen effect, thermal conductivity can become lower than that for the still air, that is, even less than 25 mW/m.K [17].
For example, silica aerogel is a highly porous material with pore diameters in the range of 10–100 nm. The porosity is more than 90% with a thermal conductivity lower than that of air, which makes these aerogels a highly insulating material. The space not occupied by solids in an aerogel is normally filled with air (or another gas) unless the material is sealed under vacuum. These gases can also transport thermal energy through the aerogel. The pores of silica aerogel are open and allow the passage of gas through the material. The final mode of thermal transport through silica aerogels involves infrared radiation [14]. Soleimani Dorcheh and Abbasi reported the synthesis of nanostructured silicon based transparent aerogels with pore diameter 20–40 nm [18].
Water molecules do not interact strongly with the hydrophobic aerogel pore walls and therefore will not lose much energy in colliding with the wall and the progress of these molecules will not be significantly slowed. Accordingly, the aerogel possesses high breathability, that is, high permeation selectivity between water vapor and agent vapors. Titania aerogels demonstrated an excellent mesoporous structure for application as photoanodes of dye-sensitized solar cells with power conversion efficiency improvement of 16% [19]. Sol-gel derived silica has found tremendous applications as a biocompatible scaffold for the immobilization of cells. A new method for rapid, reproducible, and sensitive detection of rhizobia using aerogels has been reported for the first time [20].
Thermal insulation properties of aerogels are closely related to their acoustic properties too. The acoustic propagation in aerogels depends on the interstitial gas nature and pressure, density, and more generally the texture [21]. Different applications of aerogels are given in Figure 4.
3. Classification of Aerogels
Aerogels can be classified on the basis of the following [22].
On the basis of appearance
Monolith
Powder
Film/felts
On the basis of preparation methods
Aerogel
Xerogel
Cryogel
Other aerogel-related materials
On the basis of different microstructures
Microporous aerogel (<2nm)
Mesoporous aerogel (2–50nm)
Mixed porous aerogel
On the basis of chemical structure
Oxides
Polymers
Mixed
Hybrid
Composite.
4. Preparation of Aerogels
Different type of aerogels can be prepared using alumina, chromium, tin oxide, and carbon, but preparation of silica based aerogel is comparatively easier and reliable. Aerogels are synthesized via a sol-gel process consisting of three main steps [Figure 3].
(1) Gel Preparation. Solid nanoparticles grow crosslink and finally form a three-dimensional solid network with solvent filled pores. To begin with a gel is created in solution and then the liquid is carefully removed to leave the aerogel intact; initially the creation of a colloidal suspension of solid particles known as a “sol” takes place; for example, silica gels are synthesized by hydrolyzing monomeric tetrafunctional and trifunctional silicon alkoxide precursors employing a mineral acid or a base as a catalyst [23, 24]. There are many ways to create silica based sol gels. One is by mixing tetraethoxysilane Si(OC2H5)4 with ethanol and water to make it polymerize and thus producing a water based silica gel as shown in (3). A solvent, such as methanol, is used to extract and replace the water [25]:
(3)Si(OCH2C3)4(liq.)+2H2(liq.)⟶SiO2(solid)+CH2CH3OH(liq.)
(2) Aging of the Gel. It provides strength to the structure of gel. The gel prepared earlier is aged in its mother solution [26]. This aging process strengthens the gel, so that minimum shrinkage occurs during the drying step [27]. After gelification, the gel is left undisturbed in the solvent to complete the reaction. After completion of reaction the aerogel product is formed. Inorganic aerogels can be prepared via sol-gel processing, a technique which requires alkoxides or metal salts in alcoholic or aqueous solutions, and subjecting to supercritical drying.
(3) Drying. The solvent has to be removed whilst preserving the solid aerogel network. This can be done either by supercritical drying or at ambient conditions. Aerogel materials are typically prepared by removing the solvent contained in a gel matrix by extraction in a supercritical fluid medium. This can be accomplished by bringing the gel solvent system above its critical temperature and pressure and subsequently relieving pressure above the critical temperature until only vapor remains.
Alternatively, the gel solvent system can be extracted from the wet gel with an appropriate solvent. Liquid carbon dioxide is the most popular extraction solvent because it is inexpensive and has a relatively low critical temperature and critical pressure [28–31].
Crack-free silica aerogels can also be obtained via solvent exchange and resulting surface modification of wet gels using either isopropyl alcohol, trimethylchlorosilane, or n-hexane solution [32]. The physics and chemistry involved in the synthesis of aerogels are detailed in the literature on aerogels [18, 23, 33–37].
For dense silica, solid conductivity is relatively high (a single pane window transmits a large amount of thermal energy). However, silica aerogels possess a very small (~1–10%) fraction of solid silica. Additionally, the solids that are present consist of very small particles linked in a three-dimensional network with many “dead-ends.” Therefore, thermal transport through the solid portion of silica aerogel occurs through a very tortuous path and is not particularly effective [38]. Use of methyltrimethoxysilane coprecursor makes the aerogel hydrophobic and makes it able to hold water droplets on the surface [39]. Porosity of silica aerogels was determined by helium pycnometry using the following formula and was found to be 1900 kg/m3 [40]:
(4)Porosity(%)=(1-ρbρs),
where ρb is the bulk density and ρs is the skeleton density.
The hydrophobic aerogels have also been obtained via coprecursor method pioneered by Schmidt and Schwertfeger [13]. Hydrolysis and condensation rates of all the coprecursors were observed to be slower than that of TEOS because the former contains one or more nonreactive alkyl/aryl groups, which are nonhydrolysable, and a three-dimensional solid network is achieved as per the following chemical reaction:
(5)nSi(OC2H5)4+2H2O→C2H5OHOxalicAcidSiO2+4nC2H5OH
When sufficient amount of TEOS has hydrolyzed, the silyl groups of the coprecursor get attached to the silica clusters as per the following chemical reactions:(6)As the silica clusters get attached to nonhydrolysable organic groups (silyl) on their surfaces, the aerogels become hydrophobic. Hydrophobicity of aerogels will increase with the numbers of alkyl/aryl groups attached to the surface [41].
In case of organic aerogels derived from the sol-gel polymerization of resorcinol with formaldehyde, thermal conductivity components are clearly correlated with the aerogel structure; that is, the solid conductivity can be determined by the porosity and connectivity between the particles while the gaseous conductivity can be influenced by pore size and mass specific infrared absorption of the building units influences radiative transport [42].
Polymer aerogels were prepared from mixtures containing a fixed stoichiometric amount of formaldehyde and varying proportions of resorcinol (RF) and 2,4-dihydroxybenzoic acid (DHBAF) with the objective of combining the advantages of high mesopore volume and solids content of RF aerogels with the ion exchange capacity of DHBAF aerogels, and results show that the aerogel properties vary systematically as the synthesis conditions are changed. It was found that the addition of R to the synthesis mixture resulted in increased values of surface area, mesopore volume, and mean diameter, while simultaneously maintaining the ion exchange capacity of the wet gel [43, 44].
In the TG-DTA of some of the silica aerogel samples there is rapid increase in the weight loss of hydrophilic silica aerogels at 50–100°C due to evaporation of trapped H2O and alcoholic groups from hydrophilic silica aerogels which were produced by the condensation reactions of Si-OH and Si(OC2H5) groups, whereas the percentage of weight loss is negligible up to the temperature of thermal stability in case of hydrophobic aerogels [42].
The effect of heat treatment on the hydrophobicity and specific surface area has been also investigated by several researchers. The results of these studies indicate that hydrophobicity of silica aerogel decreased with increasing the heating temperature to 350°C. On further increasing the heating temperature to 500°C, silica aerogel becomes completely hydrophilic (Figure 2). Some results for MTES coprecursor based aerogels show that the hydrophobicity of the silica around 573 K corresponding to oxidation of aerogel could be maintained up to 350°C [45, 46].
TGA and DTA analyses of the hydrophobic silica aerogels. (a) PTES/TEOS = 0.5. (b) MTES/TEOS = 0.5 [79].
Distinct step of aerogel production [80].
Different applications of aerogels.
5. Structural Features
Aerogels have an unusual combination of high porosity and small pore size, making porosity characterization by conventional techniques, such as mercury intrusion, thermoporometry, and nitrogen adsorption/desorption, very difficult. All these techniques are based on the application of capillary pressures on the aerogel network, which may cause large volumetric compressions, leading to incorrect values for pore size and volume [27]. Aerogels are characterized with a very low permeability which can be explained in terms of pore size suitable for transport of water vapours/gases but not for water molecules [46]. Some aerogels such as carbon aerogels can be obtained in the form of monoliths, beads, powders, or thin films and make them promising materials for application in adsorption and catalysis [47, 48]. Organic polymer aerogels are important nanoporous materials and their nanopore structures can be modified by the chemical reactions. These properties enable carbon nanotube aerogels potential improvement over current carbon aerogels for applications such as sensors, actuators, electrodes, and thermoelectric devices [49]. The porosity provides both molecular accessibility and rapid mass transport via diffusion and for these reasons aerogels have been part of the heterogeneous catalytic materials field for over 50 years. The high porosity and mesoscopic pore diameters of aerogel structures enable the electrolyte to penetrate the entire aerogel particle [50].
An aerogel possesses the following characteristics [22].
Property characteristics
Ultralow thermal conductivity
Ultralow refractive index
Ultralow dielectric constant
High surface area
High refractive index
Ultralow relative density
Ultrahigh porosity
Structure characteristics
Gel-like structure on nanoscale coherent skeletons and pores
Hierarchical and fractal microstructure
Macroscopic monolith
Randomly crosslinking network
Noncrystalline matter.
6. Advantages of Aerogels
Aerogels are regarded as one of the most promising high performance thermal insulation materials for building applications today. With a low thermal conductivity (~13 mW/mK), they show remarkable characteristics compared to traditional thermal insulation materials. Also higher transmittances in the solar spectrum are of great interest for the construction sector. Another advantage of aerogels is their visible transparency for insulation applications which will allow their use in windows and skylights which give architects and engineers the opportunity of reinventing architectural solutions [51]. For example, the low thermal conductivity, a high solar energy, and daylight transmittance in monolithic silica aerogel make it a very interesting material for use in highly energy efficient windows [52]. For cryogenic systems, multilayered insulation (MLI) is the insulation of choice. However, MLI requires a high vacuum for optimal effectiveness. Powder insulations such as glass microspheres and aerogel beads have shown promise at soft vacuums and have a structural advantage in that they are far simpler to install and maintain [53, 54]. Due to porous structure and low density, aerogels can trap space projectiles travelling with hypervelocity speed (order of km s−1). NASA used aerogel to trap space dust particles and for thermal insulation of space suits [55–57]. One of the promising applications that promote the development of high quality transparent silica aerogel was the use of this low density material in physics as Cherenkov detector [58].
Our indoor environments are polluted by releasing many pollutants like chloride from tap-water, VOCs from organic solvents, formalin from furniture and paints, SOx and NOx from incomplete combustion of gasses and many hydrocarbons, and so on. Airborne contaminants are responsible for increasing some respiratory problems and allergies like asthma. The conversion of airborne contaminants into nontoxic compounds is an effective pathway for their removal and to protect our environment. Aerogels can also be used in air purification by removal of airborne contaminants and protect our environment by pollutants [59]. Aerogels are potentially more environmentally friendly than noble metal catalysts due to the negative environmental impact associated with mining and processing the metals [60].
Modification of aerogels is essential to achieve specific functionality and this tailoring can start during the sol-gel process either after gelation or after obtaining the aerogel. This can be done via (a) surface functionalization of aerogels for regulating the adsorption capacity and (b) applying a polymeric coating on aerogel surface. Hybrid aerogels can encompass the intrinsic properties of aerogels (high porosity and surface area) with the mechanical properties of inorganic components and the functionality and biodegradability of biopolymers [61–63].
7. Limitations of Aerogels
Widespread uses of aerogel materials are restricted at present mainly due to their
High production costs,
Poor mechanical properties,
Health issues.
Supercritical drying is the most expensive and risky aspect of aerogel making process [64]. A highly desirable goal in aerogel preparation is the elimination of the supercritical drying process. For example, Guo and Guadalupe have succeeded in synthesizing a silica based aerogel from a metastable lamellar composite through cooperative interaction between silica and surfactant species [65]. The surfactant molecules used to generate pores can be removed from the silica network through conventional solvent extraction. The porous structure is stable during this procedure, in which no supercritical extraction is used [66]. Silica aerogels are very fragile but strength of silica aerogel monoliths has been improved by a factor of >100 through crosslinking the nanoparticle building blocks of preformed silica hydrogels with poly(hexamethylene diisocyanate). These composite monoliths are much less hygroscopic than native silica, and they do not collapse when in contact with liquids [67].
Aerogels are a mechanical irritant to the eyes, skin, respiratory tract, and digestive system. Small aerogel particles can potentially cause silicosis, and so forth, when inhaled and can induce dryness of the skin, eyes, and mucous membranes. Therefore, protective gear including respiratory protection, gloves, and eye goggles must be worn while handling aerogels [68].
8. Conclusions
Paints and coatings can be used for thermal insulation of buildings and work has been done also in CSIR-CBRI [69]. But aerogels are fast becoming alternate material of choice for thermal insulation due to their ultralow thermal conductivity. In the preparation of aerogels supercritical drying is the most effective process. In the conventional preparation of aerogels, expensive raw materials and supercritical drying are used which prohibit commercialization. It is clear that for the large scale commercial aerogel production cost and risk have to be reduced. Aerogels can only be used as building material if we can utilize their highly thermal insulation properties with light weight and low cost.
There is little that can be done to reduce thermal transport through the solid structure of aerogels. Lower density aerogels can be prepared (as low as 0.003 g/cm3), which reduces the amount of solid present, but this leads to aerogels that are mechanically weaker. Additionally, as the amount of solids decreases the mean pore diameter increases (with an increase in the gaseous component of the conductivity). These are, therefore, generally not suitable for insulation applications. Carbon is an effective absorber of infrared radiation and, in some cases, actually increases the mechanical strength of the aerogel. At ambient pressure the addition of carbon lowers the thermal conductivity from 0.017 to 0.0135 W/mK [Figure 5]. The minimum value for the carbon composite of ~0.0042 W/mK corresponds to ~R30/inch. Hence, conclusion can be drawn that aerogels have great future potential in a wide range of applications as energy efficient insulation, windows, acoustics, and so forth [41, 70, 71].
Thermal conductivity versus pressure curves for (i) pure silica aerogel and (ii) single-step silica aerogel with 9% (wt/wt) carbon black [70].
Chiral mesoporous SiO2 (CMS) as shown in Figure 6 can be synthesized with amino acid block copolymers and their acoustically induced optical Kerr effects (AIOKE) were found very high compared to nonchiral SiO2 and therefore CMS can be used in acoustically operated quantum electronic devices [72]. Recently cellulose nanofibril (CNF) aerogels with superior wet resilence and water activated shape recovery were fabricated without chemical crosslinking by ice crystal templated self assembly of TEMPO oxidised CNFs via cyclic freezing thawing method.Main challenge lies in the strengthening of aerogels either by crosslinking with cellulosic polymers or the incorporation of cellulose-based nanofibres. Other challenge is lowering the production cost of composite/hybrid aerogel materials via ambient drying and continuous production technology.
HRTEM images of chiral Ex-SiO2-CBC, (a) at low and (b) at high resolution [72].
Conflict of Interests
The authors declare that there is no conflict of interests regarding the publication of this paper.
Acknowledgment
The authors are grateful to the Director, CSIR-CBRI, for his continuous guidance and encouragement.
McNaughtA. D.WilkinsonA.2ndIUPAC Goldbook, PAC, 2007, 791801Oxford, Cambridge, UKBlackwell Science10.1351/goldbook.A00173AegerterM. A.LeventisN.KoebelM. M.2011New York, NY, USASpringerGuinness Records Names JPL's Aerogel World's Lightest SolidNASA Jet Propulsion Laboratory, 2002HigaK.Aerogel—the insulative frozen smoke20141431KistlerS. S.Coherent expanded aerogels and jellies193112732117412-s2.0-0000903815SmithD. M.DeshpandeR.BrinkerC. J.Preparation of low-density aerogels at ambient pressure for thermal insulation1993317180MayerS. T.PekalaR. W.KaschmitterJ. L.Aerocapacitor. An electrochemical double-layer energy-storage device199314024464512-s2.0-0027541981LeventisN.ChandrasekaranN.Sotiriou-LeventisC.MumtazA.Smelting in the age of nano: iron aerogels200919163652-s2.0-5754910529810.1039/b815985hTappanB. C.HuynhM. H.HiskeyM. A.ChavezD. E.LutherE. P.MangJ. T.SonS. F.Ultralow-density nanostructured metal foams: combustion synthesis, morphology, and composition200612820658965942-s2.0-3364674417910.1021/ja056550kHüsingN.SchubertU.Aerogels—airy materials: chemistry, structure, and properties1998371-222452-s2.0-0031906650RichterK.NorrisP. M.ChangC. L.PrasadV.JaluriaY.ChenG.Aerogels: applications, structure and heat transfer phenomena19956chapter 261114HrubeshL. W.Aerogel applications19982251–33353422-s2.0-0032044566SchmidtM.SchwertfegerF.Applications for silica aerogel products19982251–33643682-s2.0-0032044935FrickeJ.FrickeJ.Thermal transport in porous superinsulations1986694103Springer Proceedings in PhysicsNovakZ.KnezŽ.Diffusion of methanol-liquid CO2 and methanol-supercritical CO2 in silica aerogels19972212-31631692-s2.0-0031358135TamonH.KitamuraT.OkazakiM.Preparation of silica aerogel from TEOS199819723533592-s2.0-003251812910.1006/jcis.1997.5269SmithD. M.MaskaraA.BoesU.Aerogel-based thermal insulation19982251–32542592-s2.0-0032044780Soleimani DorchehA.AbbasiM. H.Silica aerogel; synthesis, properties and characterization2008199110262-s2.0-3754905626110.1016/j.jmatprotec.2007.10.060ChiangY. C.ChengW. Y.LuS. Y.Titania aerogels as a superior mesoporous structure for photoanodes of dye-sensitized solar cells20127869106919AroraP.SharmaS.GhoshalS. K.DilbaghiN.ChaudhuryA.A functional approach toward xerogel immobilization for encapsulation biocompatibility of Rhizobium toward biosensor20138662663110.1007/s11515-013-1286-7ForestL.GibiatV.WoignierT.Biot's theory of acoustic propagation in porous media applied to aerogels and alcogels19982251–32872922-s2.0-0032041138DuA.ZhouB.ZhangZ.ShenJ.A special material or a new state of matter: a review and reconsideration of the aerogel20136394196810.3390/ma6030941BrinkerC. J.SehgalR.HietalaS. L.DeshpandeR.SmithD. M.LoyD.AshleyC. S.Sol-gel strategies for controlled porosity inorganic materials199494851022-s2.0-002850073010.1016/0376-7388(93)E0129-8GuravJ. L.NadargiD. Y.RaoA. V.Effect of mixed Catalysts system on TEOS-based silica aerogels dried at ambient pressure20082555301930272-s2.0-5694909097110.1016/j.apsusc.2008.08.059AcharyaA.JoshiD.GokhaleV. A.AEROGEL—a promising building material for sustainable buildings2013916SmirnovaI.SuttiruengwongS.ArltW.Feasibility study of hydrophilic and hydrophobic silica aerogels as drug delivery systems200435054602-s2.0-1064428134410.1016/j.jnoncrysol.2004.06.031PatelR. P.PurohitN. S.SutharA. M.An overview of silica aerogels200914105210572-s2.0-77953442083PierreA. C.PajonkG. M.Chemistry of aerogels and their applications200210211424342652-s2.0-003685435610.1021/cr0101306AkimovY. K.Fields of application of aerogels (review)20034632872992-s2.0-394310205310.1023/A:1024401803057PajonkG. M.Some applications of silica aerogels200328176376512-s2.0-003838239010.1007/s00396-002-0814-9BissonA.RigacciA.LecomteD.RodierE.AchardP.Drying of silica gels to obtain aerogels: phenomenology and basic principles200321459362810.1081/DRT-120019055LeeC. J.KimG. S.HyunS. H.Synthesis of silica aerogels from waterglass via new modified ambient drying20023711223722412-s2.0-003660321910.1023/A:1015309014546PierreA. C.The chemistry of precursors solutions19981chapter 21189AmbekarA. P.BagadeP.A review on: aerogel—world’s lightest solid20065196102PierreA. C.RigacciA.AegerterM. A.LeventisN.KoebelM. M.SiO2 aerogels20112145Advances in Sol-Gel Derived Materials and TechnologiesCarraherC. E.Jr.General topics: silica aerogels—properties and uses2005301238638810.1080/00323910500402961CarraherC. E.Jr.Silica aerogels—synthesis and history200530626410.1080/00323910500459185PajonkG. M.Transparent silica aerogels19982251-33073142-s2.0-0032041548Venkateswara RaoA.PajonkG. M.Effect of methyltrimethoxysilane as a co-precursor on the optical properties of silica aerogels20012851–32022092-s2.0-003536956610.1016/S0022-3093(01)00454-9RaoA. V.KaleshR. R.Comparative studies of the physical and hydrophobic properties of TEOS based silica aerogels using different co-precursors2003465095152-s2.0-164231311910.1016/j.stam.2003.12.010LuX.CapsR.FrickeJ.AlvisoC. T.PekalaR. W.Correlation between structure and thermal conductivity of organic aerogels199518832262342-s2.0-33645048115KangS.-K.ChoiS.-Y.Synthesis of low-density silica gel at ambient pressure: effect of heat treatment20003519497149762-s2.0-003429936710.1023/A:1004842728314PekalaR. W.KongF. M.Resorcinol-formaldehyde aerogels and their carbonized derivatives1989301221223CarrottP. J. M.MarquesL. M.CarrottM. M. L. R.Core-shell polymer aerogels prepared by co-polymerisation of 2,4-dihydroxybenzoic acid, resorcinol and formaldehyde20121581701742-s2.0-8485965207310.1016/j.micromeso.2012.03.040ShiF.WangL.LiuJ.ZengM.Effect of heat treatment on silica aerogels prepared via ambient drying20072334024062-s2.0-34347225516HostickaB.NorrisP. M.BrenizerJ. S.DaitchC. E.Gas flow through aerogels19982251–32932972-s2.0-0032041198Moreno-CastillaC.Maldonado-HódarF. J.Carbon aerogels for catalysis applications: an overview20054334554652-s2.0-1084425656610.1016/j.carbon.2004.10.022BryningM. B.MilkieD. E.IslamM. F.HoughL. A.KikkawaJ. M.YodhA. G.Carbon nanotube aerogels20071956616642-s2.0-3425061398610.1002/adma.200601748TaoY.EndoM.KanekoK.A review of synthesis and nanopore structures of organic polymer aerogels and carbon aerogels20081192200DongW.SakamotoJ. S.DunnB.Electrochemical properties of vanadium oxide aerogels2003413112-s2.0-003867957710.1016/S1468-6996(03)00012-3BaetensR.JelleB. P.GustavsenA.Aerogel insulation for building applications: a state-of-the-art review20114347617692-s2.0-7995151832210.1016/j.enbuild.2010.12.012JensenK. I.Passive solar component based on evacuated monolithic silica aerogel19921452372392-s2.0-0026903997FesmireJ. E.AugustynowiczS. D.RouanetS.Aerogel beads as cryogenic thermal insulation system613Proceedings of the Cryogenic Engineering Conference (CEC '01)July 200115411548Advances in Cryogenic Engineering10.1063/1.1472188NayakA. L.TienC. L.Thermal conductivity of microsphere cryogenic insulation1977222512622-s2.0-0017426749WawrykR.RafalowiczJ.The influence of residual gas pressure on the thermal conductivity of microsphere insulations1988946116252-s2.0-002403768610.1007/BF00503159BurchellM. J.ColeM. J.PriceM. C.KearsleyA. T.Experimental investigation of impacts by solar cell secondary ejecta on silica aerogel and aluminum foil: implications for the Stardust Interstellar Dust Collector20124746716832-s2.0-8486033796510.1111/j.1945-5100.2011.01294.xFesmireJ. E.Aerogel insulation systems for space launch applications2006462-31111172-s2.0-3324446655610.1016/j.cryogenics.2005.11.007TabataM.AdachiI.IshiiY.KawaiH.SumiyoshiT.YokogawaH.Development of transparent silica aerogel over a wide range of densities201062313393412-s2.0-7795782645310.1016/j.nima.2010.02.241DunnaN. J. H.CarrollaM. K.AndersonA. M.Characterization of alumina and nickel-alumina aerogels prepared via rapid supercritical extraction2011521250251YangR.ZhangY.-P.ZhaoR.-Y.An improved model for analyzing the performance of photocatalytic oxidation reactors in removing volatile organic compounds and its application20045412151615242-s2.0-10244279126KanamoriK.Organic-inorganic hybrid aerogels with high mechanical properties via organotrialkoxysilane-derived sol-gel process2011119138516222-s2.0-78651257230PlawskyJ. L.LittmanH.PaccioneJ. D.Design, simulation, and performance of a draft tube spout fluid bed coating system for aerogel particles201019921311382-s2.0-7674911282710.1016/j.powtec.2009.12.009RamadanH.CoradinT.MasseS.El-RassyH.Synthesis and characterization of mesoporous hybrid silica-polyacrylamide aerogels and xerogels20113263752-s2.0-7995806498110.1007/s12633-010-9064-5FrickeJ.EmmerlingA.Aerogels—recent progress in production techniques and novel applications1999131–32993032-s2.0-0032314549GuoY.GuadalupeA. R.Functional silica aerogel from metastable lamellar composite199943153162-s2.0-0033590718DaiS.JuY. H.GaoH. J.LinJ. S.PennycookS. J.BarnesC. E.Preparation of silica aerogel using ionic liquids as solvents200032432442-s2.0-0034615004LeventisN.Sotiriou-LeventisC.ZhangG.RawashdehA.-M. M.Nanoengineering strong silica aerogels2002299579602-s2.0-003855490010.1021/nl025690eCryogel 5201, 10201 Safety Data Sheet, Aspen Aerogels. 11/13/07ThapliyalP. C.KaradeS. R.Studies on physico-mechanical behavior of thermal insulating coatings for buildingsProceedings of the International Conference on Advanced Materials for Energy Efficient Buildings (AME2B '13)2013TS452RettlebachT.SauberlichJ.KorderS.FrickeJ.Thermal conductivity of silica aerogel powders at temperatures from 10 to 275K199518627828410.1016/0022-3093(95)00051-8AccorsiJ. V.The impact of carbon black morphology and dispersion on the weatherability of polyethylene20015463213262-s2.0-0035360529PaikP.MastaiY.KitykI.RakusP.GedankenA.Synthesis of amino acid block-copolymer imprinted chiral mesoporous silica and its acoustically-induced optical Kerr effects20121921271312-s2.0-8485955061710.1016/j.jssc.2012.03.058http://www.cabot-corp.comMeadorM. A. B.NguyenB. N.GuoH.VivodS.HeZ.MalowE.SilvaR.Aerogels: thinner, lighter, stronger2011, www.nasa.gov/topics/technology/features/aerogels.htmlAspen AerogelsInsulated building materialsUS Patent 7771609, 2010Aspen AerogelsInsulated building materialsUS Patent 8277676, 2012http://www.aerogel.com2011, http://www.chem-eng.kyushu-u.ac.jp/e/research.htmlJeongA.-Y.KooS.-M.KimD.-P.Characterization of hydrophobic SiO2 powders prepared by surface modification on wet gel2000191–34834872-s2.0-034389807810.1023/A:1008716017567BłaszczyńskiT.ŚlosarczykA.MorawskiM.Synthesis of aerogel by supercritical drying method20135720020610.1016/j.proeng.2013.04.028