Material feeding and handling systems have been cited as one of the most common causes of process downtime where thermochemical conversion processes are concerned. New and emerging fuels come in a variety of forms, and if such fuels are to be deployed widely it is imperative that material feeding and handling systems are designed appropriately. This study proposes an approach for designing material feeding and handling systems for use with coarse solid fuels. The data obtained from this study indicates particle size to be one of the key issues affecting the flowability of bulk solids further to the uniformity in particle shape. Coarse bulk solid samples were shown to flow more freely than their milled and pulverised counterparts, generating higher degrees of flowability. The results from this study were also applied to a new feed system used for feeding solid fuels to high pressure processes named the Hydraulic Lock Hopper. In this study the Hydraulic Lock Hopper demonstrated the feeding of wood pellets, torrefied spruce pellets, and ground anthracite coal grains against a pressure of 25 barg in two modes of operation. Energy savings compared to conventional lock hopper systems were recorded in the region of 80%.
The number of biomass fed systems has increased dramatically in recent years and with this much has been learnt about the dynamics of operating a biomass fired plant. Due to the apparent similarities to coal plants, many mistakes have been made in the development and utilisation of biomass fuels in thermochemical conversion processes, not least where material handling and feeding are concerned [
The assessment of a material’s properties is of paramount importance when handling bulk solids. Where combustion and gasification systems are concerned, material feeding and handling systems have been cited as one of the most common causes of process downtime, especially when handling new and emerging fuels [
But aside from the difference in inherent safety when handling such fuels in their milled form, attention should be focused on how parent materials behave in their coarse bulk form. Fuels are present in their coarse bulk form for the majority of their lifetime, and therefore systems should be designed appropriately to handle fuels in this form to avoid feeding and handling problems. Much work has been carried out regarding the handling of fine and milled materials, most notably that carried out by Jenike and Janssen [
The aim of this study is to scale up and apply the same design procedure used for fine materials to coarse bulk solids and to determine the physical properties of a range of new and emerging fuels key to the design of storage and feeding devices. Physical properties of coarse bulk solids will be compared to fine and milled materials, and such fuels will be assessed alongside a new feeding system used for feeding solid fuels to high pressure processes, named the Hydraulic Lock Hopper (HLH).
Six fuels were tested: wood pellets (Ø6 mm), torrefied wood pellets (Ø8 mm), ground anthracite coal grains (~10 mm), torrefied wood chips (20–50 mm), milled wood pellets (200–600
Particle and bulk density of each material.
Material | Particle density |
Bulk density |
---|---|---|
Wood pellets | 1.26 ± 0.006 | 0.651 ± 0.004 |
Torrefied wood pellets | 1.27 ± 0.004 | 0.677 ± 0.002 |
Ground anthracite | 1.35 ± 0.004 | 0.731 ± 0.001 |
Torrefied wood chips | 0.43 ± 0.005 | 0.170 ± 0.001 |
Milled wood pellets | 1.53 ± 0.005 | 0.344 ± 0.007 |
Pulverised coal | 1.51 ± 0.010 | 0.542 ± 0.007 |
The wood pellets used are commercially available and were procured from CPL Distribution Ltd. They are made from chemically untreated residues from the wood processing industry and comprise a physically stable low ash pellet conforming to the standard ENplus A1. The pellets described were used as the starting material for the milled wood pellets and were milled using a hammer mill fitted with a trapezoidal screen of size 1.5 mm. The coarsely ground anthracite coal grains were also procured from CPL Distribution Ltd. and have an average particle size of approximately 10 mm. The coal grains are characteristic of anthracite and display a submetallic lustre. Both the torrefied wood pellets and wood chips were made available by the Energy Centre of the Netherlands (ECN), were made from spruce, and were torrefied at a temperature of 260°C for approximately 40 minutes. The pulverised coal was of bituminous rank and was sized approximately 220
The approach used for assessing coarse bulk solids physical properties was adapted from that proposed by Jenike for hopper design incorporating fine materials [
As the work carried out by Jenike largely concerned fine materials, the associated apparatus, namely, the Jenike Shear Cell, is scaled accordingly. Where coarse materials are concerned, such apparatus is unable to be used [
Two types of annular shear testers were used. A large scale Ø1 m annular shear tester shown in Figure
Large scale annular shear tester (a) and large scale wall friction tester (b) used for measuring coarse bulk solids.
Due to the scale of the apparatus used, the lowest consolidation stress used in this study (approximately 1.0 kPa) was limited by the inherent mass of the shear cell lid. Consolidation stresses greater than this were chosen and spaced to ensure shear planes in different regions of the bulk material being sheared were generated.
As with the material shear test, two types of wall friction shear tester were used. A large scale Ø28 cm annular shear tester shown in Figure
The principle of both wall friction shear testers is the same; however, they differ slightly in how they are operated. In the case of the Brookfield PFT, the operational procedure is similar to that carried out for the material shear test. However, in place of the cupped lid used to measure the interparticle friction, an annular sample of wall material is fitted. Material is loaded into the same annular shear cell used for the material shear tests, levelled, and the annular sample of wall material is applied to the material at a known load. The shear cell containing the bulk solid is rotated at a constant velocity and in turn the material is sheared by the sample of wall material.
The large scale linear wall friction tester shears the bulk solid in a single direction. It is comprised of a circular ring and lid, a bracket, and a mechanical shearing arm. The bracket and shearing arm are connected and attached to the circular ring via a load cell which measures the shear stress generated. The circular ring is placed on top of a sample of wall material and a known mass of a bulk solid is placed inside the ring. A lid of known mass is then placed on top of the bulk solid and in turn a normal load is applied to the lid to create a stress normal to the bulk solid. The shearing arm is engaged and the bulk solid is sheared against the sample of wall material.
The general wall shear principle detailed above for both cases can be used for a broad range of wall materials. In this study stainless steel, mild steel, and TIVAR 88 were assessed in relation to all six of the stated bulk solids. TIVAR 88 is a low friction lining material commonly implemented in hoppers handling cohesive bulk solids. It acts to reduce phenomena such as arching and ratholing.
The HLH embodies an alternative system to conventional lock hoppers for feeding solid fuels to high pressure processes. Initial work with the HLH is detailed in [
The HLH is comprised of two hoppers, equal in volume, running in series, and separated by a valve. In addition to this principal valve, a pipe runs external to both of the hoppers and acts to connect and separate the two via an additional valve. A high pressure water pump is connected to the top of the two hoppers and is used in the compression stage of the feeding operation. No pressurising gas is needed to operate the HLH and the only work required in the compression stage is that to pump water against a back pressure.
The initial configuration of the HLH is such that the top hopper is at atmospheric pressure and the bottom hopper is at a desired operating pressure. Fuel is fed to the top hopper and is sealed at atmospheric pressure. The principal valve connecting the two hoppers is opened and fuel is fed to the bottom hopper. During this stage, pressure equalisation takes place and both hoppers are contained at an equal pressure higher than that of the atmosphere but lower than that of the operating pressure. The principal valve is then shut and the valve in the external pipe connecting the two hoppers is opened. Water is pumped to the top hopper against a back pressure and acts to displace the gas in the top hopper at high pressure. Fuel does not become contaminated with water during this stage as the fuel being fed is located in the bottom hopper during the compression phase. Water is only ever present in the top hopper during the compression phase and therefore does not contaminate the fuel being fed. As the water level in the top hopper increases, the pressure in both the head space above the liquid level and the bottom hopper containing the fuel increases. The water pump is disengaged once the desired operating pressure is reached and the valve in the external pipe is closed. A valve at the exit of the bottom hopper is opened and the fuel is fed to the high pressure process with no net change in pressure. The water is then drained from the top hopper and the process is able to start anew. This describes Mode 1. The HLH can be operated in an additional mode: Mode 2.
The operational procedure for Mode 2 is broadly similar to Mode 1, with the exception that only the top hopper is required. When the primary valve is opened, the fuel is fed directly to the process at pressure. The difference between the two modes comes in the compression stage. Mode 2 requires the top hopper to be completely filled with water, thus displacing a maximum of gas at high pressure, whereas the volume of water required to be pumped in Mode 1 is approximately equal to the void space present between the fuel prior to feeding. This typically varies between 40 and 60% for most solid fuels [
A linear relationship of increasing shear stress with increasing normal stress is shown in Figure
Family of yield loci for each material.
The reason for both fine materials requiring a larger shear stress to shear the material at the same normal stress but where the consolidation stress is increased is due to material cohesion and an increased level of cohesion. Materials cohesion is generally found to increase as mean particle size decreases due to interparticle forces representing the dominant forces in the bulk material [
Applying Mohr stress analysis to the plots shown in Figure
Broad classification of the material flow function and definition of flowability for each material.
Material | Material flow |
Flow function |
---|---|---|
Wood pellets | 6.12 | Easy-flowing |
Torrefied wood pellets | 24.0 | Free-flowing |
Ground anthracite | 6.37 | Easy-flowing |
Torrefied wood chips | 6.49 | Easy-flowing |
Milled wood pellets | 2.91 | Cohesive |
Pulverised coal | 3.72 | Cohesive |
Material flow function for each material.
Coarse materials can generally be considered to be easy-flowing when dry. This is due to inertial and gravitational forces being the dominant forces in the bulk material. In the case of all of the coarse materials, the material flow function indicates that a low stress is required to generate incipient flow and deformation of the material even after a significant consolidation load has been applied. In the case of both the milled wood pellets and pulverised coal, a strong linear relationship between consolidation stress and unconfined yield stress is observed. Both materials are indicated to be cohesive with the milled wood pellets being observed to be more cohesive than the pulverised coal. This can be attributed to the relative particle size variation and the respective particle shape. In the case of the milled wood pellets, a broader range of particle sizes is present and further to this a broad range of particle shapes. The milled wood pellets are largely made up of needle-like structures interspersed with finer material. It is supposed that it is these needle-like structures that interact to form more stable bulk structures which in turn require a larger stress to create a deformation. Comparatively, the pulverised coal is seen to be broadly uniform in size and shape.
In addition to the material flow function, Mohr stress circle analysis allows both the effective angle of internal friction and the angle of internal friction of each material to be determined. Figure
Effective angle of internal friction and angle of internal friction with varying consolidation stress.
Both trends are observed in all materials and both angles are observed to be broadly similar in all cases. This is with the exception of the milled wood pellets which highlights a greater degree of interparticle friction, reflected by the marginally higher effective angle of internal friction recorded.
Due to the HLH being predominantly manufactured out of mild steel and the HLH incorporating water during its operation, the mild steel sample was tested when being both dry and wet. The kinematic angle of wall friction is a pivotal parameter when determining the angle at which a material will flow and in the case of the HLH, when determining the hopper half angle required to generate flow. Assessing the mild steel wall sample when wetted provides a more accurate value for design in the case of the HLH.
Figure
Kinematic angle of wall friction with varying normal stress.
In the majority of cases either the TIVAR 88 or mild steel sample require the smallest shear force to be imparted to generate displacement. Therefore, hoppers constructed from either of these materials are required to be the least steep when compared to the remaining materials. It is observed from Figure
The wood pellets, torrefied pellets, and torrefied wood chips display similar wall friction angles for all wall material samples. Values of approximately 30° are recorded for both wet mild steel and stainless steel and between 15° and 20° for dry mild steel and TIVAR 88, where normal stresses in excess of 2 kPa are generated. Ground anthracite coal presents an anomaly, recording lower friction angles with all wall material samples. The anthracite coal has a hard and smooth surface and thus inherently has a lower coefficient of friction than any of the remaining coarse materials. Further to this, as the particle size is significantly larger than the pulverised coal, the bulk solid is able to hold its shape more readily and slide freely over the wall material.
Comparing the milled wood pellets with the pulverised coal, it can be seen from Figure
When designing a hopper for storing and feeding a bulk solid, a series of hopper flow factor plots developed by Jenike detailed in Bulletin number 123 [
Table
Hopper half angle for all fuels using TIVAR 88, stainless steel, and mild steel as wall materials.
Material | Hopper half angle (°) | |||
---|---|---|---|---|
TIVAR 88 | Stainless steel | Mild steel | Wet mild steel | |
Wood pellets | 33 | 17 | 34 | 10 |
Torrefied wood pellets | 29 | 17 | 34 | 15 |
Ground anthracite | 31 | 31 | 38 | 34 |
Torrefied wood chips | 32 | 12 | 28 | 11 |
Milled wood pellets | 31 | 37 | 38 | 14 |
Pulverised coal | 13 | 14 | 13 | 0 |
In the case of the wood pellets, torrefied pellets, ground anthracite, and torrefied wood chips, an intersection of the material flow function with the hopper flow factor does not occur in the stress range measured. This is due to the easy-flowing nature of the coarse bulk solids. As a consequence, a critical stress for flow cannot be determined and in turn neither can a minimum outlet diameter for a conical hopper. Where this is found, the general rule of sizing the outlet diameter to a value of 10 to 12 times the average particle diameter (
Table
Minimum outlet diameter as a multiple of average particle diameter (
Material | Minimum hopper outlet diameter/ | |||
---|---|---|---|---|
TIVAR 88 | Stainless steel | Mild steel | Wet mild steel | |
Milled wood pellets | 492 | 553 | 557 | 418 |
Pulverised coal | 582 | 614 | 582 | 495 |
Each of the hoppers used in the experimental setup of the HLH has an outlet diameter of 76 mm and a hopper half angle of 28.5°. While this diameter is smaller than any of those stated in Table
In addition to the HLH being operated in Mode 1 and Mode 2, the HLH was operated as a conventional single and dual lock hopper to provide a to-scale comparison to a widely deployed high pressure feed system. Both systems (single and dual lock hopper) were operated using a three-stage compressor in the compression stage, and thus the energy requirements for all systems (HLH, single and dual lock hopper) were determined experimentally.
Referencing Table
Figure
Energy requirement of the HLH (Mode 1 and Mode 2), a conventional single lock hopper and a dual lock hopper.
Mode 1 is seen to generate a higher energy saving compared to Mode 2 in all cases and the greatest energy saving comes when feeding the ground anthracite coal in Mode 1 compared to a conventional single lock hopper. This is followed by the torrefied pellets and then the standard wood pellets. This trend is observed due to the smaller void space present in the top hopper prior to feeding when operating with the ground anthracite compared to the two pelletised fuels and in turn the lower energy requirement by the high pressure water pump operating in Mode 1. Although this also affects both types of conventional lock hopper as this means a smaller volume of gas has to be compressed; energy saving is relative and so this benefit does not translate to a decrease in energy saving.
Comparatively, this benefit is not felt when both the conventional and dual lock hopper are compared to Mode 2. As the energy required by the high pressure water pump remains constant for all fuels in Mode 2, it is only the mass per batch that affects the energy required per unit mass fed. The reduction in void space presented by the torrefied pellets over the standard wood pellets and in turn the ground anthracite over the torrefied pellets does not constitute an advantage for Mode 2, whereas it does for both a conventional and a dual lock hopper. Figure
Energy saving generated by the HLH operating in Mode 1 and Mode 2 compared to a conventional single lock hopper (a) and a dual lock hopper (b).
It is important to examine the effect the HLH has on the moisture content of the fuel due to the inherent use of water in the system. The effect of wet conditions can be very significant due to the formation of interparticle liquid bridges. This is especially true where moisture unstable fuels are being fed, as slight changes in moisture content can dramatically alter a fuel’s physical properties and promote flow problems. Therefore, analysing the effect the HLH has on the moisture content of a fuel being fed allows an assessment to be made regarding the compatibility of a feedstock with the system.
Moisture content variations were analysed using wood pellets as the primary feedstock as wood pellets present an absorbent fuel able to most accurately monitor moisture uptake brought about during feeding. Moisture content was assessed assuming that any mass increase across the pressure boundary was due to the uptake of water by the pellets and so the mass of each batch of wood pellets was assessed before and after feeding was completed. Table
Effect of the HLH on the moisture content of wood pellets.
Pressure (barg) | Moisture content increase (%) | |
---|---|---|
Mode 1 | Mode 2 | |
10 | 0.37 ± 0.25 | 0.54 ± 0.21 |
15 | 0.27 ± 0.03 | 0.81 ± 0.22 |
20 | 0.31 ± 0.12 | 0.22 ± 0.01 |
25 | 0.60 ± 0.07 | 0.50 ± 0.37 |
It can be seen from Table
In addition to work with wood pellets, moisture content increases were also recorded when feeding torrefied wood pellets and ground anthracite grains. Measurements were taken for an operating pressure of 25 barg and during operation in Mode 1. Moisture contents were found to increase by approximately 0.2% and 0.6% when feeding torrefied wood pellets and ground anthracite grains, respectively.
The Jenike design procedure was explored for a broad range of materials with varying particle size and shape for use in new high pressure solids feed system, the Hydraulic Lock Hopper. Large scale shear testing equipment was used to quantify the interparticle friction effects of four coarse fuels: wood pellets, torrefied wood pellets, torrefied wood chips, and ground anthracite grains, and the Brookfield Powder Flow Tester was used in conjunction with two fine fuels: milled wood pellets and pulverised bituminous coal. Tests showed all of the coarse fuels to be either free-flowing or easy-flowing materials, whereas both of the fine fuels were found to be cohesive. Wood pellets, torrefied wood pellets, and ground anthracite grains were successfully fed to pressures as high as 25 barg using the Hydraulic Lock Hopper, in two modes of operation. Energy savings in the region of 80% for Mode 1 and 75% for Mode 2 compared to a conventional lock hopper were consistently achieved while feeding all fuels. Energy savings were found to peak at 82.9% when feeding ground anthracite grains at a pressure of 25 barg in Mode 1 compared to a conventional lock hopper operating at the same pressure. In addition to this, it was found that the Hydraulic Lock Hopper has a negligible effect on the moisture content of the fuel being fed, with moisture content increases less than 1 wt% being recorded in all cases.
The authors declare that there is no conflict of interests regarding the publication of this paper.
The authors gratefully acknowledge the Engineering and Physical Science Research Council (EPSRC) and the Biomass and Fossil Fuels Research Alliance (BF2RA) for their financial support. Special thanks go to ECN for supplying the torrefied material and to the Wolfson Centre for Bulk Solids Handling Technology for their guidance and use of their laboratory facilities. Thanks also go to Mike O’Meara and David Palmer (University of Sheffield) for their technical assistance in the construction of the experimental rig.