Advances in Materials Science and Engineering
Volume 2015 (2015), Article ID 504628, 5 pages
http://dx.doi.org/10.1155/2015/504628

Research Article

Design and Micromagnetic Simulation of Fe/L1₀-FePt/Fe Trilayer for Exchange Coupled Composite Bit Patterned Media at Ultrahigh Areal Density

Warunee Tipcharoen,¹ Arkom Kaewrawang,¹ and Apirat Siritaratiwat²

¹Magnetic Materials & Data Storage Research Laboratory, Department of Electrical Engineering, Faculty of Engineering, Khon Kaen University, Thailand
²KKU-Seagate Cooperation & EMC/EMI Research Laboratory, Department of Electrical Engineering, Faculty of Engineering, Khon Kaen University, Thailand

Received 16 December 2014; Accepted 13 January 2015

Academic Editor: Pavel Lejcek

Copyright © 2015 Warunee Tipcharoen et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

Exchange coupled composite bit patterned media (ECC-BPM) are one candidate to solve the trilemma issues, overcome superparamagnetic limitations, and obtain ultrahigh areal density. In this work, the ECC continuous media and ECC-BPM of Fe/L1₀-FePt/Fe trilayer schemes are proposed and investigated based on the Landau-Lifshitz-Gilbert equation. The switching field, , of the hard phase in the proposed continuous ECC trilayer media structure is reduced below the maximum write head field at interlayer exchange coupling between hard and soft phases, , higher than 20 pJ/m and its value is lower than that for continuous L1₀-FePt single layer media and L1₀-FePt/Fe bilayer. Furthermore, the of the proposed ECC-BPM is lower than the maximum write head field with exchange coupling coefficient between neighboring dots of 5 pJ/m and over 10 pJ/m. Therefore, the proposed ECC-BPM trilayer has the highest potential and is suitable for ultrahigh areal density magnetic recording technology at ultrahigh areal density. The results of this work may be gainful idea for nanopatterning in magnetic media nanotechnology.

1. Introduction

An ultrahigh areal density of magnetic recording media over 1 Tb/in² and overcoming the superparamagnetic limit of conventional perpendicular magnetic recording are required for the development of hard disk drive technology. Magnetic recording media must have smaller magnetic grains, higher magnetocrystalline anisotropy constant, , and lower exchange coupling [1]. The high is the cause of increasing coercivity, , of the media; however, it may be over the maximum write field of about 24-25 kOe of heads because the saturation magnetization, , of the write head material is limited [2]. These problems are called the magnetic recording trilemma [3]. There are three conditions of the trilemma that limits areal density growth of magnetic recording technology: (i) the write head field can record data on the media, (ii) the bits must be thermally stable, and (iii) the number of grains per bit is sufficient to obtain the high signal to noise ratio.

From the above writing head field problem, several future magnetic recording technologies are proposed to reduce switching field, , to the maximum write head field or lower. Heat-assisted magnetic recording technology allows a reduced of the media during the writing process [4]. The of the media under a microwave-assisted field in microwave-assisted magnetic recording technology is lower [5]. The magnetization reversal of the media is excited by the microwave field. The tilted media were proposed to reduce and areal density achieved was 62% higher than that of a perpendicular media with 45° easy-axis-tilted media under the same thermal stability and recording process [6]. In addition, the exchange coupled composite (ECC) media proposed by Victora and Shen and the exchange spring and exchange coupled graded media proposed by Suess provide better thermal stability, writability, and improved signal to noise ratio [1, 7]. The of the media is reduced with the same thermal stability. Due to these media comprising soft and hard magnetic materials, the soft phase helps to reverse the magnetization of the hard phase. Therefore, the of the media can be reduced.

At ultrahigh density magnetic recording, the magnetic transition noise also becomes a significant problem. However, this problem is completely eliminated by bit patterned media (BPM) because of the separation of bits by nonmagnetic material [8]. Therefore, it is the candidate for magnetic recording technology to overcome the superparamagnetic limit at areal density of 1 Tb/in². Recently, the concepts of ECC-BPM of [Co/Pd]₅/Pd/[Co/Ni]₃/Co multilayer have been introduced, showing that can be reduced by inserting a Pd layer while maintaining thermal stability [9]. The ECC-BPM and graded BPM media for L1₀-FePt material are investigated with of 1–4 MJ/m³ [10]. After that the structure of high of L1₀-FePt and low of a Co/Pd-Co/Ni multilayer with various the interlayer exchange couplings between hard and soft phases, , can reduce the [11]. In addition, both the and saturation field are reduced by 50% owing to exchange coupling between L1₀-FePt and the Fe interface after the postannealing process [12].

To achieve the reduction of below the maximum write head field at ultrahigh areal density, ECC media of Fe/L1₀-FePt/Fe trilayer structure for BPM are proposed and investigated in this work. Exchange coupling coefficient between neighboring dots, , for the structure becomes a challenge due to magnetic bits being close to other bits [13]. Magnetic flux from individual bit will disturb neighboring bits. Therefore, the and on the of the hard layer, its hysteresis loop, magnetization reversal, and magnetic energy are investigated by the object oriented micromagnetic framework (OOMMF) program [14] based on the Landau-Lifshitz-Gilbert (LLG) equation [15].

2. Micromagnetic Simulation and Modeling

The LLG equation is used to describe the magnetization dynamics of magnetic particles, as shown in the following [15, 16]:

where is the gyromagnetic ratio, is the magnetization vector of the magnetic particles, is the effective field vector, as illustrated in (2), and is the Gilbert damping constant. For the first term, the magnetization is affected by the , so the magnetization rotates around with the precession torque term. For the second term, the magnetization is damped to the called the damping torque term. The in the LLG equation includes anisotropy, demagnetization, exchange, and external (Zeeman) fields that result from the derivative of the total magnetic energy density, , with respect to . The includes anisotropy, demagnetization, exchange, and Zeeman energy densities [15, 16]:

ECC media comprise soft and hard magnetic materials and L1₀-FePt is used for the hard magnetic material of the recording layer because it has a high . The ideal value is about 7 MJ/m³ [17] and can be achieved with a minimum stable grain size of about 2.81 nm, but that value will be difficult to produce by the magnetron sputtering method. Therefore, we use of 2.8 MJ/m³ [16, 18] for this work and the minimum stable grain size increases to 3.59 nm [16]. Fe material is used for the soft magnetic material because of epitaxial growth [19]. The of soft and hard phases is 1200 and 500 kA/m, respectively [18, 20]. The of the soft phase is 100 J/m³ [18, 21]. The exchange coupling constant of soft and hard phases is 28 and 12 pJ/m, respectively [18, 21]. The and are varied to investigate the effects of exchange coupling behavior on the reduction of . In the present work, is defined as the applied magnetic field that completely reverses the magnetization in the hard phase. The continuous media have width and length of 250 nm. The thickness of L1₀-FePt hard phase, , is 10 nm. The Fe soft phase thickness, , of the ECC bilayer is 10 nm and the proposed ECC trilayer continuous media are 5 and 10 nm. For the proposed ECC-BPM, the dot dimension is 10 nm × 10 nm with the same and of the continuous media. The dot spacing is 2.5 nm to achieve an ultrahigh areal density, as shown in Figure 1. The mesh size of the finite difference time domain calculation is 2.5 nm × 2.5 nm × 2.5 nm by OOMMF program based on the LLG equation.

Figure 1: Structures of the proposed ECC-BPM trilayer: Fe/L1₀-FePt/Fe with 400 dots at areal density over 4 Tb/in².

3. Results and Discussions

3.1. Fe/L1₀-FePt/Fe Trilayer Structure for Continuous Media

To demonstrate the advantage and performance of the proposed ECC trilayer structure, a comparison between the bilayer and the proposed ECC trilayer is investigated. The effective for the trilayer structure is 5 and 10 nm to reduce below the maximum write head field. Figure 2 shows the dependence of normalized (divided by of single layer continuous media) on for bilayer and trilayer. The of the continuous single layer medium is independent of and constant at 1 while the normalized of the bilayer and trilayer continuously decreases. The normalized of the bilayer decreases faster than that of the proposed trilayer media with increasing from 0 to 9 pJ/m, but it is not in the writing head field region. For of 12.5–30 pJ/m, the of the trilayer media continuously decreases below the maximum write head field and its value is lower than the of the bilayer media. This result indicates that the proposed ECC trilayer media can reduce the lower than the bilayer media because of the double interface area [22].

Figure 2: Normalized and of single layer continuous media, ECC bilayer, and proposed ECC trilayer.

Reduction of the corresponds to calculation of energy barrier height; both of them decrease with increasing exchange energy per unit area [23] or . Energy barrier of the hard magnetic phase, , in the proposed trilayer structure is calculated by the Stoner-Wohlfarth model as given in the following:

where is of hard magnetic materials, is the thickness of hard phase, is external magnetic field, is exchange coupling constant, is of hard magnet, and () is the anisotropy field of hard phase. We have also found that a hard phase of the proposed ECC media trilayer structure has a lower energy barrier than the bilayer structure with high thermal stability.

Moreover, the exchange energy density at full reversal (not shown here) of the ECC bilayer and trilayer rapidly increases at of 8–12.5 pJ/m for bilayer and trilayer ( = 5 nm) and 8–15 pJ/m for trilayer ( = 10 nm). Therefore, the in these ranges suddenly reduces. For over 15 pJ/m, the is almost constant according to the exchange energy. These results indicate that is important for ECC media in reducing the below the maximum write head field at ultrahigh recording density. Thus, the proposed ECC trilayer continuous media structure has more potential reduction than the ECC bilayer continuous media at the same for ultrahigh density magnetic recording technology.

3.2. Fe/L1₀-FePt/Fe Trilayer Structure for BPM

The proposed ECC-BPM structure with of 5 and 10 nm, as shown in Figure 1, is expected to achieve the goal of reducing below the maximum write head field at ultrahigh areal density. The of the bit patterned dots is normalized by the of the single layer without , as shown in Figure 3. It significantly decreases because of the and . The values of of ECC-BPM trilayer and bilayer tend to decrease unlike the BPM single layer. This indicates that the influence on the ECC structure is highly significant for BPM. Although there is no in the trilayer structure, the can be kept within the maximum head field region at very high . Under the influence of and , the of the ECC-BPM trilayer with of 10 nm is the lowest. ECC-BPM bilayer ( = 10 nm) and trilayer ( = 5 nm) can reduce the close to the maximum write head field. However, the ECC-BPM trilayer with of 10 nm is the most effective in reducing below the maximum write head field. This indicates that the also affects the reduction of . Therefore, this structure has benefit for magnetic recording technology to solve the magnetic recording trilemma issues at ultrahigh areal density.

Figure 3: Dependence of normalized on with various .

Figure 4 shows the hysteresis loops and magnetic domain of the ECC-BPM bilayer and the proposed trilayer. The bilayer and the first trilayer structure denoted by trilayer 1 have and of 10 pJ/m and the second trilayer structure denoted by trilayer 2 has of 10 pJ/m and without . There are different steps in the hysteresis loop shapes. Principally, the reasons are that (i) magnetization reversal of soft and hard phases is separate and the soft phase reverses early because the magnetic properties of the soft magnetic material allow the magnetization to reverse easily and after that the hard phase will reverse and (ii) exchange coupling between interface of soft and hard phases is not enough [1, 24, 25]. Therefore, magnetization reversal of soft and hard phases is separate. The proposed trilayer 1 has a sharp loop and no step because of its structure and the existence of and .

Figure 4: Hysteresis loops of ECC-BPM bilayer with and of 10 pJ/m (solid line), trilayer 1 with and of 10 pJ/m (dotted line), and trilayer 2 with of 10 pJ/m and without (dashed line). Magnetization reversal process of single dot in bilayer: (a) and (d), trilayer 1: (b) and (e), and trilayer 2: (c) and (f). Magnetization reversal of (a)–(c) without and (d)–(f) at of −18 kOe.

Magnetization reversal processes in Figures 4(a)–4(c) and 4(d)–4(f) are shown without and with an applied external magnetic field, , of −18 kOe, respectively. Without , the magnetization of soft phases in trilayer 2 and bilayer structures begins to reverse but the hard phase magnetization still remains in the + direction (pointing up). When increases in the − direction (pointing down), the magnetic domain wall moves to the interface between soft and hard phases. All magnetization of soft phases will be reversed but hard phase magnetization is still in the same direction, as shown in Figures 4(d) and 4(f). Magnetization of the ECC-BPM trilayer 1 is fully reversed, as shown in Figure 4(e). The magnetic domain shows that an added Fe soft layer to the proposed trilayer structure can reduce the below the maximum write head field.

4. Conclusions

The proposed Fe/L1₀-FePt/Fe ECC trilayer structure for continuous media and BPM was investigated by a micromagnetic model. The proposed trilayer continuous media has lower than that of bilayer and the maximum write head field at over 20 pJ/m. For the proposed ECC-BPM structure, the and have more influence on the reduction of . The of the ECC-BPM is lower than the maximum write field at of 10 pJ/m and of 5 pJ/m. The magnetization of the L1₀-FePt hard phase of the proposed ECC-BPM trilayer easily reverses compared to the bilayer. To the best of the authors’ knowledge, the proposed ECC-BPM trilayer is the most effective in reducing the compared to the other structure schemes in literature. The results of this work will lead to the nanomaterials development of the magnetic recording technology at ultrahigh areal density, potentially solving the writability issue of the trilemma.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

This work is financially supported by Khon Kaen University, Thailand, under Incubation Researcher Project. This work is also financially supported by Thailand Research Fund (TRF) and Khon Kaen University, Grant no. TRG5780125. TRF and Khon Kaen University are not always necessarily in agreement with the authors’ discussions in this paper. The authors deeply thank Assistant Professor Dr. Anupap Meesomboon, Dr. Sataporn Pornpromlikit, and Dr. Ian Thomas for suggestions.

References

D. Suess, J. Lee, J. Fidler, and T. Schrefl, “Exchange-coupled perpendicular media,” Journal of Magnetism and Magnetic Materials, vol. 321, no. 6, pp. 545–554, 2009.

M. H. Kryder and R. W. Gustafson, “High-density perpendicular recording—advances, issues, and extensibility,” Journal of Magnetism and Magnetic Materials, vol. 287, pp. 449–458, 2005.

H. J. Richter, “The transition from longitudinal to perpendicular recording,” Journal of Physics D: Applied Physics, vol. 40, no. 9, pp. R149–R177, 2007.

M. H. Kryder, E. C. Gage, T. W. McDaniel et al., “Heat assisted magnetic recording,” Proceedings of the IEEE, vol. 96, no. 16, pp. 1810–1835, 2008.

J.-G. Zhu, X. Zhu, and Y. Tang, “Microwave assisted magnetic recording,” IEEE Transactions on Magnetics, vol. 44, no. 1, pp. 125–131, 2008.

Y. Y. Zou, J. P. Wang, C. H. Hee, and T. C. Chong, “Tilted media in a perpendicular recording system for high areal density recording,” Applied Physics Letters, vol. 82, no. 15, pp. 2473–2475, 2003.

R. H. Victora and X. Shen, “Composite media for perpendicular magnetic recording,” IEEE Transactions on Magnetics, vol. 41, no. 2, pp. 537–542, 2005.

C. A. Ross, “Patterned magnetic recording media,” Annual Review of Materials Science, vol. 31, pp. 203–235, 2001.

T. Hauet, E. Dobisz, S. Florez et al., “Role of reversal incoherency in reducing switching field and switching field distribution of exchange coupled composite bit patterned media,” Applied Physics Letters, vol. 95, no. 26, Article ID 262504, 2009.

P. Krone, D. Makarov, T. Schrefl, and M. Albrecht, “Exchange coupled composite bit patterned media,” Applied Physics Letters, vol. 97, no. 8, Article ID 082501, 2010.

A. T. McCallum, P. Krone, F. Springer et al., “ FePt based exchange coupled composite bit patterned films,” Applied Physics Letters, vol. 98, no. 24, Article ID 242503, 2011.

H. Wang, M. T. Rahman, H. Zhao et al., “Fabrication of FePt type exchange coupled composite bit patterned media by block copolymer lithography,” Journal of Applied Physics, vol. 109, no. 7, Article ID 07B754, 2011.

M. Hwang, M. Farhoud, Y. Hao et al., “Major hysteresis loop modeling of two-dimensional arrays of single domain particles,” IEEE Transactions on Magnetics, vol. 36, no. 5, pp. 3173–3175, 2000.

M. J. Donahue and D. G. Porter, The object oriented micromagnetic framework (OOMMF) program release 1.2 α5, 2002, http://math.nist.gov/oommf

Y. Wang, Physics and micromagnetic analysis of advanced recording technologies [Ph.D. Dissertation], Carnegie Mellon University, Pittsburgh, Pa, USA, 2011.

J. Zhang, Y. Liu, F. Wang, R. Zhang, Z. Wang, and X. Xu, “Design and micromagnetic simulation of the L10-FePt/Fe multilayer graded film,” Journal of Applied Physics, vol. 111, no. 7, Article ID 073910, 2012.

N. H. Nam, N. T. T. Van, N. D. Phu, T. T. Hong, N. H. Hai, and N. H. Luong, “Magnetic properties of FePt nanoparticles prepared by sonoelectrodeposition,” Journal of Nanomaterials, vol. 2012, Article ID 801240, 4 pages, 2012.

W. Tipcharoen, A. Kaewrawang, A. Siritaratiwat, and K. Tonmitra, “Investigation on magnetic properties of L1₀-FePt/Fe graded media multilayer,” Advanced Materials Research, vol. 802, pp. 189–193, 2013.

J.-L. Tsai, P.-R. Chen, Y.-H. Chen, and Q.-S. Luo, “Magnetic properties and microstructure of FeOx/Fe/FePt and FeOx/FePt films,” Journal of Nanomaterials, vol. 2013, Article ID 954621, 8 pages, 2013.

F. Wang, X.-H. Xu, Y. Liang, and J. Zhang, “Perpendicular -FePt/Fe and -FePt/Ru/Fe graded media obtained by post-annealing,” Materials Chemistry and Physics, vol. 126, no. 3, pp. 843–846, 2011.

E. E. Fullerton, J. S. Jiang, M. Grimsditch, C. H. Sowers, and S. D. Bader, “Exchange-spring behavior in epitaxial hard/soft magnetic bilayers,” Physical Review B—Condensed Matter and Materials Physics, vol. 58, no. 18, pp. 12193–12200, 1998.

Y. Wang, R. Wang, H.-L. Xie, J.-M. Bai, and F.-L. Wei, “Micromagnetic simulation with three models of FeCo/L10 FePt exchange-coupled particles for bit-patterned media,” Chinese Physics B, vol. 22, no. 6, Article ID 068506, 2013.

H. Zeng, J. Li, J. P. Liu, Z. L. Wang, and S. Sun, “Exchange-coupled nanocomposite magnets by nanoparticle self-assembly,” Nature, vol. 420, no. 6914, pp. 395–398, 2002.

Z. S. Shan, J. P. Liu, V. M. Chakka, H. Zeng, and J. S. Jiang, “Energy barrier and magnetic properties of exchange-coupled hard-soft bilayer,” IEEE Transactions on Magnetics, vol. 38, no. 5, pp. 2907–2909, 2002.

M. Kapoor, X. Shen, and R. H. Victora, “Effect of intragranular exchange on exchange-coupled composite media,” Journal of Applied Physics, vol. 99, no. 1, Article ID 08Q902, 2006.