BioMed Research International
Volume 2016 (2016), Article ID 5081653, 7 pages
http://dx.doi.org/10.1155/2016/5081653

Research Article

Evaluation of Culture Conditions to Obtain Fatty Acids from Saline Microalgae Species: Dunaliella salina, Sinecosyfis sp., and Chroomonas sp.

D. A. Castilla Casadiego,1,2 A. R. Albis Arrieta,¹ E. R. Angulo Mercado,² S. J. Cervera Cahuana,¹ K. S. Baquero Noriega,¹ A. F. Suárez Escobar,³ and E. D. Morales Avendaño⁴

¹Engineering Faculty, Chemical Engineering Program, Bioprocess Research Group, Universidad del Atlántico, Km 7 Antigua Vía a Puerto Colombia, Barranquilla, Colombia
²Basic Sciences Faculty, Chemistry Program, Biotechnology of Microalgae Research Group, Universidad del Atlántico, Km 7 Antigua Vía a Puerto Colombia, Barranquilla, Colombia
³Engineering Faculty, Universidad de Bogotá Jorge Tadeo Lozano, 4 Avenue No. 22-61, Bogotá, Colombia
⁴Sciences Experimental Faculty, Universidad del Zulia, Calle 61 con Prolongación Avenida 77, Maracaibo 4011, Venezuela

Received 3 January 2016; Revised 26 April 2016; Accepted 12 May 2016

Academic Editor: Wenguang Zhou

Copyright © 2016 D. A. Castilla Casadiego et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

The use of the saline microalgae, Dunaliella salina, Sinecosyfis sp., and Chroomonas sp., was explored as an alternative source for the production of fatty acids using fertilizer and glycerol as culture media. The nutrient medium used contained “Nutrifoliar,” a commercial fertilizer, and/or glycerol, in natural sea water. The microalgae were placed in cultures with different conditions. The parameters that favored the largest production of fatty acids were 24 hours of agitation and illumination, 1620 L/day of air supply, 2.25 L of air/min, and a temperature of 32°C using “Nutrifoliar” as the culture media. Results indicated that, from 3 g of microalgae in wet base of Chroomonas sp., 54.43 mg of oil was produced. The chromatographic characterization of oil obtained revealed the presence of essential fatty acids such as 9,12,15-octadecatrienoic acid (omega-3) and 4,7,10-hexadecatrienoic acid (omega-6) from the species Dunaliella salina. On the other hand, 9,12-octadecadienoic acid (omega-6) and cis-11-eicosenoic acid (omega-9) were identified from the species Chroomonas sp. The temperature variations played an important role in the velocity of growth or the production of the algae biomass, the amount of oil, and the ability to produce fatty acids.

1. Introduction

Essential fatty acids are divided into two main families: omega-3 (n-3) and omega-6 (n-6), which are denominated as polyunsaturated fatty acids (PUFAs). This is due to the fact that its carbon chains are not saturated with hydrogen atoms and have more than one double bond between carbon atoms [1]. There are certain fatty acids that our organism is not able to synthesize, called essential fatty acids. These are of vital importance, contributing to the health of human beings and therefore must be administered through a person’s diet [2].

A normal consumption of PUFAs has been associated with good health of human beings [3]. Fatty acids play a role in the development and maintenance of correct cerebral function, especially in the gestation period and childhood [4]. Several researches show that PUFAs protect and help reduce risk of contracting cardiovascular illnesses [5], diseases in premature babies [6], in the lactation and pregnancy period [7], ocular diseases associated with age [8], Alzheimer’s disease [9], inflammatory illnesses [10], diabetes prevention [11], and certain types of cancer [12]. Finally, these lipids can be used for treatment of mental illnesses [13] and weight loss [14].

Currently, omega-3 fatty acids are obtained from sources such as fish oil, salmon, tuna, halibut, anchovy or herring, shrimp, and dried fruit oils [15]. Also, omega-6 fatty acids can be found in foods such as vegetable oil like soy, safflower, or corn; in dried fruit and seeds [16]; and in small amounts in meat, birds, and eggs [17].

One of the biggest problems to obtain these fatty acids from fish oil is their residual taste, which is not pleasant for the human palate, reducing its consumption and market sales. Due to the refinement process of this oil, necessary to eliminate the residual taste, the final product is more expensive, and on account of this alternative ways to obtain these lipids have been proposed in order to replace PUFAs from fish oil, using as feedstock another type of marine life like microalgae [15].

Recently, it has been proved that certain species of microalgae accumulate, under specific culture conditions, a good amount of fatty acids [15]. In particular, some saline strains present high percentages of omega oils that allow the exploration of obtaining, on a commercial scale, essential fatty acids such as docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA). Various studies developed with different microalgae used to obtain these fatty acids are shown in Table 1.

Table 1: Values (%) of EPA and DHA fatty acid contents with relations to total lipids in some microalgae [16].

Microalgae
% of EPA and DHA production
Reference

Nannochloropsis salina
~28 EPA
[17]

Thraustochytrium sp.
45.1 EPA + DHA
[18]

Dunaliella salina
21.4 EPA
[19]

Pavlova viridis
36.0 EPA + DHA
[20]

Isochrysis galbana
~28.0 EPA + DHA
[21]

With the purpose of understanding which other species of saline algae can be good precursors to obtain fatty acids, this study presents as the principal objective to determine the potential of the species of saline microalgae, Dunaliella salina, Sinecosyfis sp., and Chroomonas sp., as sources of essential fatty acids, evaluating the best culture conditions that could help generate a larger production of algae biomass, amount of oil, and the ability to produce fatty acids of interest. Besides, this study explores the alternative of using commercially available feedstock, such as commercial fertilizers and glycerol, for the formulation of the growth medium of the culture of saline microalgae in order to reduce the cost associated with nitrogen and carbon sources for the production of fatty acids omega-3 using microalgae.

2. Materials and Methods

2.1. Microorganisms

The microalgae used correspond to three species: Dunaliella salina, Chroomonas sp., and Sinecosyfis sp. These species were donated by the Ceparium of Photosynthetic Microorganism’s Laboratory of the Biology, Department of the Experimental Science Faculty, the Universidad del Zulia, Maracaibo, Venezuela. These strains were provided in test tubes with 10 mL of algal culture medium containing 4 mM of nitrogen and a salinity of 3.5%.

2.2. Nutrients and Culture Conditions

The algae were submerged in different conditions of growth, alternating the nutrient medium to obtain biomass: commercial “Nutrifoliar” fertilizer with a 4 mM concentration of nitrogen and glycerol at 4 mM of carbon, both in filtrated sea water and autoclaved. The cultures were at controlled temperatures of 20°C and 32°C. The artificial illumination was supplied through fluorescent lamps (Sylvania Daylight plus F96T12/DLP) of 75 W for all the cultures, with a luminous flow of 16880 lm, (16 lamps). The illumination source was regulated: a continuous exposition was supplied for selected cultures and others were submerged at a photoperiod of light : darkness 12 h : 12 h. The agitation and supply of air were provided through air pumps (PowerLife P -500), which provide 2.25 L of air/min with the purpose of avoiding the sedimentation of algae and permit culture homogenization.

Natural sea water was obtained from Salgar Beach in the Atlantic Coast, Colombia, coordinate latitude 11°1′16.62′′N, longitude 74°56′7.24′′W. The salinity of the sterile sea water was measured with conductivity electrodes, WTW brand and Multi 3420 model. The registered value was 37.5% and 56.2 mS/cm, for salinity and conductivity, respectively. All the materials used were previously sterilized in autoclave at 121°C.

2.3. Cell Growth

Cell growth was determined by taking daily samples of 5 mL from each of the different cultures and determining the concentration of microalgae spectroscopically (Spectronic Genesys 2), measuring the absorbance at a wavelength of 647 nm and monitoring each culture in fixed 24-hour intervals. Moisture content in centrifuged microalgae was obtained, drying samples of microalgae at 105°C until constant weight.

2.4. Lipid Extraction

The lipid fraction of microalgae was extracted using Soxhlet method, which is based on the constant evaporation and condensation through stages of a volatile solvent for posterior contact with the sample studied. Quantities of the biomass between 1.5 and 2.4 grams were weighed for each microalga and were subjected to Soxhlet extraction using analytic hexane (JT Baker) as solvent.

A mixture of hexane and lipids was obtained from the process of extraction. This mixture was separated through a rotary evaporator Büchi Heating Bath Model B-490 at 48°C, with a rotation velocity 64–66 rpm, for 45 minutes.

2.5. Determination of the Fatty Acids Profile

The extracted oils were transesterified, adding 1 mL of a methanolic solution of NaOH 1%. The mixture was heated to 55°C for 15 min and then 2 mL of a methanol solution containing 2% of HCl was added and heated for another 15 min [22]. Later, the obtained FAMEs were dissolved in 1 mL of hexane and injected to an Agilent 7890 A gas chromatograph, coupled to a selective mass detector 5975C (Agilent), with an Agilent Select Biodiesel for FAME column (30 m, 0.20 mm, 0.25 μm), using Helium as a carrier gas with a flow of 1 mL/min and a volume of injection of 1 μL, with a temperature programmed at 60°C for 2 minutes and then incremented in 15°C/min until a final temperature of 240°C was reached, with a time duration of 10 minutes. The injector and detector temperature were of 250°C according to EN 14103. The total time of analysis was 36.3 minutes.

2.6. Experimental Design

The experimental conditions evaluated are presented in Table 2.

Table 2: Variables and factors of experimentation.

Factors ()
Variables
Levels

: nutrient type
Nutrifoliar

Glycerol
+

: temperature (°C)
20

32
+

: agitation time (h)
12

24
+

: photoperiod light : darkness (h)
12 : 12

24 : 0
+

: air supply (L/day)
810

1620
+

Six experiments were established to develop this investigation and these are presented in Table 3, alternating the levels (− or +) which symbolize the different conditions or factors of experimentation presented in Table 2. Experiments were done in triplicate.

Table 3: Experimental factors level combinations.

Experimental condition

1

+
+
+
+

2

+

3

+
+
+

4
+
+
+
+
+

5
+
+

6
+

+
+
+

3. Results and Discussion

Some of the conditions studied according to the experimental design were no favorable for the algae growth. In Table 4, the conditions where the algae showed an increase of population are marked with “YES,” and those where the algae was not able to adapt are marked with “NO.”

Table 4: Results of culture condition evaluations and treatment of the microalgae species subject to studies.

Experimental condition
Microalgae/evaluation of culture conditions and treatment

Dunaliella salina
Sinecosyfis sp.
Chroomonas sp.

1
YES
YES
YES

2
NO
NO
YES

3
YES
YES
YES

4
NO
NO
NO

5
YES
NO
YES

6
NO
NO
NO

Table 4 allows concluding that the microalgae have a higher affinity for the media formulation composed by the commercial fertilizer, “Nutrifoliar,” when compared to the culture media enriched with glycerol. Clearly, this can be observed for experimental conditions 4 and 6 reported in Table 4, where it is demonstrated that none of the microalgae species were able to survive in the media containing glycerol under these experimental conditions, but an acceptance of glycerol was seen when the experimental conditions 5 showed Table 3 were employed, which refers to the conditions of agitation, illumination, and air supply in low levels. The strains, Dunaliella salina and Chroomonas sp., were able to show a pattern of effective growth. The opposite effect was presented under the fourth-experimental conditions with high levels of agitation time, illumination, and air supply, which led to the death of this microalga. The species, Sinecosyfis sp., did not grow at any of the experimental conditions with glycerol. These can be explained either by the rapid depletion of the initial nitrogen contained in sea water when no additional nitrogen is added as it was done in the experiment that uses the culture media enriched with glycerol, or by osmotic stress due to the presence of glycerol in the enriched media, or by the combination of both phenomena.

Evaluating the effect of the variable temperature, experiments 1 and 3 reported that microalgae can grow under established conditions of 20 and 32°C. On the other hand, the species Chroomonas sp. was able to live through the established conditions of low levels of agitation time, illumination, and air supply, which make reference to experiment 2, Table 4.

Figures 1 and 2 show kinetics of growth of the microalgae species that were able to adapt and grow, under different conditions established in Table 4.

Figure 1: Comparative growth curves of Dunaliella salina, Sinecosyfis sp., and Chroomona sp. microalgae, employing the commercial fertilizer, in conditions 20 and 32°C of temperature, agitation and illumination of 24 hours, and air supply of 1620 L/day.

Figure 2: Comparative growth curves that represent absorbance versus time in days of microalgae Dunaliella salina and Chroomonas sp., employing glycerol and “Nutrifoliar” as nutrient mediums, at 20°C, an agitation and illumination of 24 hours, and an air supply of 1620 L/day.

Figure 1 shows that the temperature at which the microalgae culture grew is an influential and selective parameter for the microalgae species, exerting an effect in the concentration of biomass in time. The microalgae culture of Sinecosyfis sp. and Chroomonas sp. at 32°C showed the highest concentrations of biomass, generating a reason for accumulation each day of 1.53 and 1.23 times more for the Chroomonas sp. and Sinecosyfis sp. microalgae, respectively, in the 11 days of culture, in comparison with the same strains of microalgae exposed to a growth below 20°C. The growth of Dunaliella salina microalgae under these two conditions of temperature demonstrated that this microalga is selective at temperatures around 20°C, presenting a higher concentration of almost double the biomass, in comparison with cultures exposed at 32°C. Other researchers that had studied the Chlorella sp., Nannochloropsis sp. [23], and Isochrysis galbana microalgae [24] have reported that cultures exposed to moderately warm temperatures and high levels of light are able to grow significantly more. This is due to the increment in temperature, which favorably contributes to the photosynthesis [25] and respiration [26], reflecting an accelerated algal growth [23, 27]. Table 5 describes the behavior or stages of kinetic growth of microalgae seen in Figure 1. These cultures were recollected once they achieved the stationary growing phase to proceed with the oil extraction. One control for each culture was allowed to continue its growing, showing the final death phase for every culture. After centrifugation, wet microalgae showed average moisture of 68.8%.

Table 5: Kinetic growth behavior of microalgae presented in Figure 1.

Microalgae
Behavior at 20°C
Behavior at 32°C

Dunaliella salina
Linear, exponential, stationary
Adaptation, exponential, stationary

Sinecosyfis sp.
Linear, stationary
Linear, exponential, stationary

Chroomonas sp.
Linear, stationary
Linear, exponential, stationary

Figure 2 shows that microalgae have a favorable acceptance of “Nutrifoliar” as its nutrient medium. This is due to the fact that the adaptation phase of the culture was less relevant in the kinetics described in Table 5, going straight to the linear phase, followed by the exponential phase (in some cases), stationary phase, and death phase. The highest absorbance data was achieved at 32°C, with 1.187 absorbance units with Chroomonas sp. microalgae and 1.127 absorbance units with Sinecosyfis sp. Both results were reported after 15 days of culture growth. At 32°C, the microalgae Dunaliella salina demonstrated little acceptance, due to the fact that it presented an adaptation phase for more than seven days, starting with an absorbance of 0.17 at the first day to 0.317 after seven days at 32°C. Evaluating its growth at 20°C, its concentration went from 0.18 of absorbance the first day to 0.77 after the seven days of culture. At 20°C, the exponential phase was not projected for Sinecosyfis sp. and Chroomonas sp. microalgae, causing it not to be able to grow with vitality and firmness; for this reason the lowest biomass concentration was generated.

Figure 2 shows glycerol as a promising nutrient medium to achieve high concentrations of biomass in a short period of time. Observing Figure 2 in detail, the amount of biomass obtained in three days using this nutrient source was able to surpass the amount obtained using a Nutrifoliar culture in 11 days, for Dunaliella salina cultures, with a ratio of biomass concentration of about 3 times more per day. The Chroomonas sp. microalgae cultures, nourished with glycerol, also showed the same behavior observed in the Dunaliella salina cultures: the amount of biomass that was accumulated using “Nutrifoliar” in 11 days was obtained in only 5 days in a glycerol culture, at a growth ratio of about twice as much.

It could also be appreciated in the useful culture lifetime. The strains were only able to bear 4 to 5 days for the cultures nourished with glycerol, in comparison with “Nutrifoliar,” which kept them alive for 11 days. The beginning of the cellular death phase occurred at an early stage for cultures with glycerol. This suggests that the microalgae studied, due to its mixotrophic character, can use this substance as a source of carbon for growth, causing a vertiginous growth during the exponential phase, with the absence of the adaptation stage. However, this rapid growth also caused an early disappearance of other nutrients in the culture medium (possibly nitrogen), and therefore its unviability, generating a rapid decay in biomass concentration. Gallardo and Cobelas [28] presented that one of the factors for the massive production of algae is the source of carbon and nitrogen, due to the fact that the absence of these would generate disequilibrium in the cultures. For this reason, even though it generated great density of microalgae biomass, the reported results of this work with the use of glycerol (carbon source) as a culture medium did not have the capacity necessary to maintain the culture without invigorated nitrogen.

Table 6 presents the results of the oil characterization produced by each microalgae biomass using different culture conditions, revealing the fatty acids that were identified in the samples.

Table 6: Identified fatty acids and quantity of oil produced for the studied microalgae.

Experiment number

1
2
3

Nutrifoliar medium, period of agitation and illumination for 24 hours, supplied 1620 L/day of air, temperature 32°C
Nutrifoliar medium, period of agitation and illumination of 12 : 12 hours, supplied 810 L/day of air, temperature 32°C
Nutrifoliar medium, period of agitation and illumination of 24 hours, supplied 1620 L/day of air, temperature 20°C

Microalgae species
Chroomonas sp.
Dunaliella salina
Chroomonas sp.
Chroomonas sp.
Sinecosyfis sp.

Quantity of wet microalgae (g)
3
4
1.5
15.5
24

Oil produced (mg)
54.43
73.14
24.99
40.69
88.76

mg of oil/g of wet biomass
18.14
18.29
16.66
2.62
3.69

Extracted fatty acids
(1) Hexadecanoic acid, methyl ester. (palmitic acid)
(2) 9,12-Octadecadienoic acid, methyl ester. Linoleic acid, omega-6
(3) Hexadecanoic acid, 1-(hydroxymethyl)-1,2-ethanediol ester.
(4) 16-Octadecenoic acid, methyl ester (stearic acid).
(1) Hexadecanoic acid, methyl ester.
(2) 4,7,10-Hexadecatrienoic acid methyl ester. Omega-6
(3) Octadecadienoic acid, methyl ester.
(4) 9,12,15-Octadecatrienoic acid, methyl ester (Z, Z, Z). alpha-linolenic acid, omega-3
(5) 16-Octadecenoic acid, methyl ester.
(1) Hexadecanoic acid, methyl ester.
(2) Hexadecanoic acid 1-(hydroxymethyl)-1,2-ethanediol ester.
(3) Cis-11-eicosanoic acid, omega-9
(1) Hexadecanoic acid, methyl ester.
(2) Octadecanoic acid, methyl ester.
(3) 8,11-Octadecadienoic acid, methyl ester.
(1) Hexadecanoic acid, methyl ester.
(2) Octadecanoic acid, methyl ester.
(3) 8,11-Octadecadienoic acid, methyl ester

Table 6 shows the results of the chromatographic characterization of the experiments that succeeded in the production of oil. These correspond to experimental conditions 1, 2, and 3 of Table 3, in which the nutrient medium employed was “Nutrifoliar.” Those cultures that reported growth and generation of high levels of biomass, with glycerol as a nutrient source, did not provide a significant amount of oil after the extraction process. This led to the conclusion that the series of culture conditions expressed in experiment 5 of Table 3, even though a high level of biomass was produced in a short period of time, were not able to stress the microalgae to concentrate oil in its interior.

From the experimental conditions 1 (Table 3), only the results for Chroomonas sp. and Dunaliella salina microalgae are shown. Sinecosyfis sp. did not produce a significant amount of oil. From the experimental conditions 2, only the results for Chroomonas sp. are showed. For the conditions studied in experiment 3, Chroomonas sp. and Sinecosyfis sp., cultures that were able to survive, did not guarantee a considerable production of oil.

Temperature was a crucial variable that favored the production of oil and the extraction of fatty acids, because, by submitting the cultures at 20°C, the amount of oil obtained and the extraction of fatty acids decreased in comparison with the conditioning of the cultures at 32°C. Our results reported that, for each gram of wet microalgae biomass of Chroomonas sp. at 32°C (experimental conditions 1), 18.14 mg of oil was produced and 5 different fatty acids were extracted, while, for each gram of biomass of Chroomonas sp. at 20°C (experimental condition 3), 2.62 mg of oil was obtained and only 3 types fatty acids were extracted. For the experimental conditions 2, where only the agitation and illumination period were fixed at 12 : 12 h, supplied with 810 L/day of air and at 32°C, the generation of oil was 16.66 mg for each gram of wet microalgae, obtaining a very small variation in comparison with results obtained in experiment 1, stressing the fact that the temperature has more influence in the production of oil than the other variables. The production of oil of the Sinecosyfis sp. microalga was also affected by temperature, reporting that, for each gram of biomass, 3.69 mg of oil was obtained. This is due to the fact that the increment in temperature was able to stress the microalgae, favoring a greater generation in the amount of oil.

Within the culture conditions evaluated, the one that favored the production of essential fatty acids with microalgae was 24 hours of agitation and 1620 L/day of air supply, 32°C, employing Nutrifoliar at 4 mM of nitrogen as the culture medium (experimental conditions 1). At these conditions, microalgae Chroomonas sp. and Dunaliella salina produced 4 and 5 different fatty acids (Table 6), respectively, among them 9,12,15-octadecatrienoic acid (omega-3) and 4,7,10-hexadecatrienoic acid (omega-6) for Dunaliella salina; these fatty acids were also identified in the research developed by Bhosale and collaborators in 2010 [19] with this same microalgae and 9,12-octadecadienoic acid (omega-6) with Chroomonas sp. microalgae. Also, hexadecanoic acid and heptadecanoic acid were the most common fatty acids, reported in all the analysis for the samples of different microalgae, at diverse culture conditions.

4. Conclusions

The nutrient source is the main variable that affected the growth and biomass production of the microalgae. The results showed that the glycerol, which only provides the carbon source to the cultures, was useful to produce around of the same microalgae biomass concentration that “Nutrifoliar” gained in 11 days in only 3 days with the microalgae Dunaliella salina and 5 days to Chroomonas sp. Low yields of oil production were obtained using glycerol as nutrient source; therefore, the extraction of fatty acids was not successful. “Nutrifoliar” was the nutrient source that all the studied microalgae accepted the most, with almost all the different experimental conditions being favorable for the cultures. The temperature was the most influential variable, generating significant contributions on the microalgae biomass and oil production and for obtaining fatty acids. At 32°C, the microalgae, Sinecosyfis sp. and Chroomonas sp., were able to grow and produced oil. At 20°C, the microalgae Dunaliella salina grew but did not produce oil in a quantifiable amount. The parameters that favored the largest production of oil and extraction of essential fatty acids were 24 hours of agitation and illumination, 1620 L/day of air supply and 2.25 L of air/min, and a temperature of 32°C using Nutrifoliar as culture medium. At these conditions, the Chroomonas sp. and Dunaliella salina produced polyunsaturated fatty acids of the omega-3 and omega-6 families.

Competing Interests

The authors declare that they have no competing interests.

Acknowledgments

This work was financially supported by the Universidad del Atlántico, Colombia, and by the “Programa de Jóvenes Investigadores e Innovadores de COLCIENCIAS.” The author acknowledge Universidad del Zulia, Experimental Faculty of Sciences, Maracaibo, Venezuela, for the donation of microalgae and the Universidad Libre, Faculty of Engineering, Bogotá, Colombia, for the execution of chromatographic analysis.

References

A. López Farré and C. Macaya, “Efectos antitrombóticos y antiinflamatorios de los ácidos grasos omega-3,” Revista Española de Cardiología, vol. 6, supplement, pp. 31–37, 2006.

V. Díaz-Argüelles Ramírez-Corría, “Deficiencia de ácidos grasos esenciales en el feto y en el recién nacido pretérmino,” Revista Cubana de Pediatria, vol. 73, no. 1, pp. 43–50, 2001.

M. Rodríguez-Cruz, A. R. Tovar, M. del Prado, and N. Torres, “Mecanismos moleculares de acción de los ácidos grasos poliinsaturados y sus beneficios en la salud,” Revista de Investigación Clínica, vol. 57, no. 3, pp. 457–472, 2005.

M. S. Reece, J. A. McGregor, K. G. D. Allen, and M. A. Harris, “Maternal and perinatal long-chain fatty acids: possible roles in preterm birth,” American Journal of Obstetrics and Gynecology, vol. 176, no. 4, pp. 907–914, 1997.

J. J. Carrero, E. Martín-Bautista, L. Baró et al., “Efectos cardiovasculares de los ácidos grasos Omega-3 y alternativas para incrementar su ingesta,” Nutrición Hospitalaria, vol. 20, no. 1, pp. 63–69, 2005.

N. I. Velázquez Quintana, J. L. Masud Yunes Zárraga, and R. Ávila Reyes, “Recién nacidos con bajo peso; causas, problemas y perspectivas a futuro,” Boletín Médico del Hospital Infantil de México, vol. 61, no. 1, pp. 73–86, 2004.

V. Díaz-Argüelles Ramírez-Corría, “Lactancia materna: evaluación nutricional en el recién nacido,” Revista Cubana de Pediatría, vol. 77, no. 2, 2005.

J. P. SanGiovanni and E. Y. Chew, “The role of omega-3 long-chain polyunsaturated fatty acids in health and disease of the retina,” Progress in Retinal and Eye Research, vol. 24, no. 1, pp. 87–138, 2005.

R. Valenzuela B, K. Bascuñan G, and A. Valenzuela B, “Ácido docosahexaenoico (DHA): una perspectiva nutricional para la prevención de la enfermedad de Alzheimer,” Revista Chilena de Nutrición, vol. 35, pp. 250–260, 2008.

C. Pérez Tárrago, A. Puebla Maestu, and A. Miján de la Torre, “Tratamiento nutricional en la enfermedad inflamatoria intestinal,” Nutricion Hospitalaria, vol. 23, no. 5, pp. 418–428, 2008.

A. Nasiff-Hadad, E. Meri, and E. Meriño-Ibarra, “Ácidos grasos omega-3: pescados de carne azul y concentrados de aceites de pescado. Lo bueno y lo malo,” Revista Cubana de Medicina, vol. 42, no. 2, pp. 128–133, 2003.

D. Cardona, “Tratamiento farmacológico de la anorexia-caquexia cancerosa,” Nutrición Hospitalaria, vol. 21, pp. 17–26, 2006.

J. Quintero and J. Rodríguez-Quirós, “Aspectos nutricionales en el trastorno por déficit de atención/hiperactividad,” Revue Neurologique, vol. 49, pp. 307–312, 2009.

M. Sekiya, N. Yahagi, T. Matsuzaka et al., “Polyunsaturated fatty acids ameliorate hepatic steatosis in obese mice by SREBP-1 suppression,” Hepatology, vol. 38, no. 6, pp. 1529–1539, 2003.

J. Singh and S. Gu, “Commercialization potential of microalgae for biofuels production,” Renewable and Sustainable Energy Reviews, vol. 14, no. 9, pp. 2596–2610, 2010.

T. C. Adarme-Vega, D. K. Y. Lim, M. Timmins, F. Vernen, Y. Li, and P. M. Schenk, “Microalgal biofactories: a promising approach towards sustainable omega-3 fatty acid production,” Microbial Cell Factories, vol. 11, article 96, 2012.

J. Van Wagenen, T. W. Miller, S. Hobbs, P. Hook, B. Crowe, and M. Huesemann, “Effects of light and temperature on fatty acid production in Nannochloropsis salina,” Energies, vol. 5, no. 3, pp. 731–740, 2012.

S. D. Scott, R. E. Armenta, K. T. Berryman, and A. W. Norman, “Use of raw glycerol to produce oil rich in polyunsaturated fatty acids by a thraustochytrid,” Enzyme and Microbial Technology, vol. 48, no. 3, pp. 267–272, 2011.

R. A. Bhosale, M. P. Rajabhoj, and B. B. Chaugule, “Dunaliella salina Teod. as a prominent source of eicosapentaenoic acid,” International Journal on Algae, vol. 12, no. 2, pp. 185–189, 2010.

C. Hu, M. Li, J. Li, Q. Zhu, and Z. Liu, “Variation of lipid and fatty acid compositions of the marine microalga Pavlova viridis (Prymnesiophyceae) under laboratory and outdoor culture conditions,” World Journal of Microbiology and Biotechnology, vol. 24, no. 7, pp. 1209–1214, 2008.

T. Yago, H. Arakawa, T. Morinaga, Y. Yoshie-Stark, and M. Yoshioka, “Effect of wavelength of intermittent light on the growth and fatty acid profile of the haptophyte Isochrysis galbana,” in Global Change: Mankind-Marine Environment Interactions, H.-J. Ceccaldi, I. Dekeyser, M. Girault, and G. Stora, Eds., pp. 43–45, Springer, Dordrecht, Netherlands, 2011.

A. Sahu, I. Pancha, D. Jain et al., “Fatty acids as biomarkers of microalgae,” Phytochemistry, vol. 89, pp. 53–58, 2013.

C. M. James, S. Al-Hinty, and A. E. Salman, “Growth and 3 fatty acid and amino acid composition of microalgae under different temperature regimes,” Aquaculture, vol. 77, no. 4, pp. 337–351, 1989.

L. A. Velasco, J. Barros-Gómez, G. H. Ospina-Salazar, and C. A. Trujillo, “Efecto de la intensidad lumínica, temperatura y salinidad sobre el crecimiento de la microalga isochrysis galbana (clon T-ISO),” INTROPICA, vol. 4, no. 1, pp. 93–99, 2009.

C. Lobban, P. Harrison, and M. Duncan, The Physiological Ecology of Seaweeds, Cambridge University Press, New York, NY, USA, 1985.

E. Y. Dawson, Marine Botany: An Introduction, Holt, Rinehart and Winston, New York, NY, USA, 1966.

S. M. Renaud and D. L. Parry, “Microalgae for use in tropical aquaculture II: effect of salinity on growth, gross chemical composition and fatty acid composition of three species of marine microalgae,” Journal of Applied Phycology, vol. 6, no. 3, pp. 347–356, 1994.

T. Gallardo and M. Á. Cobelas, “Una revisión sobre la biotecnología de las algas,” Botanica Complutensis, vol. 15, p. 9, 1989.