RBF Nonsmooth Control Method for Vibration of Building Structure with Actuator Failure

In order to accommodate the actuator failure, the finite-time stable nonsmooth control method with RBF neural network is used to suppress the structural vibration. The traditional designed control methods neglect influence of actuator failure in structural vibration. By Lyapunov stable theory, the designed control method is demonstrated to suppress the building structural vibration with actuator failure. Finally, there are some examples to numerically simulate the three-layer building structure which is affected by El Centro seismic wave. Control effect of nonsmooth control is compared with no control and LQR control. The simulation results demonstrate that the designed control method is great for vibration of building structure with actuator failure and great antiseismic effect.


Introduction
How to reduce the severe and persistent vibration for structure under the earthquake vibration and wind resistance is a hot topic.In the last few decades, the structural vibration control was proved as an active and effective measure to suppress vibration.And international and domestic academics have brought up many kinds of effective control algorithm such as LQR (Linear Quadratic Regulator), LQG (Linear Quadratic Gaussian), ILC (Iterative Learning Control), and pole placement [1][2][3][4][5].The aforementioned results do not consider the case of actuator failure.However, actuator failure is inevitable in the real project.
Thus, more and more researchers make contributions to control strategy in the case of actuator failure.And many effective ways have some development in respect of compensation of actuator failure.The study of actuator failure is started with dealing with linear system fault [6,7].Nevertheless, the control of actuator failure is very limited in the application of building structure.
In addition, the convergence of control system is an important index [8].However, many linear control methods are to make system Lyapunov stable.What is more, they belong to asymptotic stable research field that motion track is converged to the system's equilibrium point in the case of time that tends to infinity.In the view of making control system of structural vibration rapidly stabilize, it is necessary to study control methods making closed-loop system converge in finite time.
With the study and development of Lyapunov stable theory [9] and theorem of homogeneity, continuous nonsmooth control has made certain breakthrough [8][9][10].Nonsmooth control has been widely applied [11][12][13][14][15] such as attitude control of spacecraft [12], high-precision guidance laws [14], and position control of permanent magnet synchronous motors [15].Nevertheless, this control method is not applied on the building structure.At the same time, it cannot approximate well for uncertain part.The problem causes difficulty and challenge for design and analysis of control method.By learning literature [16][17][18][19][20][21][22][23][24][25], it is not hard to find out that neural network has wide prospect.And the neural network has great approximation effect for unknown model.Meanwhile, RBF neural network has great generalization and approximates any nonlinear function at random.
The paper carries out mathematical modeling and analysis for a building structure.According to the RBF neural 2 Complexity network, the seismic wave is made by autoadaptable approximation.Then, according to finite-time stable theory and analysis of actuator failure, the finite-time stable nonsmooth algorithm is designed for the problem of structural vibration.Finally, the control system is under seismic wave called El Centro.And numerical analysis of the strong nonlinear model is studied.The control effects of nonsmooth control and LQR control are analyzed contrastively.
The main contributions of this dissertation are as follows: The impact of uncertain actuator failures on building structure vibration is considered.Meanwhile, the actuator failure is compensated with RBF neural network.Building structure vibration is suppressed in a fast speed by applying the method of finite-time nonsmooth vibration control, which prevents building structure from vibration in a long time.

The Modeling and Analysis of Building Structure
Interlaminar shear model is used.The  layers' building structure is simplified into building structure  degrees of freedom.
Effected under one-dimensional horizontal earthquake, the equation of motion is as follows [1]: In this equation,  = [ 1 ,  2 , . . .,   ]  is displacement vector of the structure relative to the ground, where   ( = 1, 2, . . ., ) is displacement of the building structural th floor relative to the ground. is mass matrix. is damping matrix. is stiffness matrix. =  is transform matrix of the ground seismic acceleration where  = [1 1 ⋅ ⋅ ⋅ 1] is the unit column of  × 1. ẍ  is the ground seismic acceleration. is a matrix denoting the location of actuators. is the control input.
We define a state-space vector  = [ where According to the rank criterion, the system (see ( 2)) is controllable.Hence, structural vibration can be suppressed effectively via designing control variable.
According to the finite-time stability theory, considering the motion equation of the structure, an actuator has been installed in each layer. is  ×  full rank matrix called invertible matrix.We use variable  = [ 1 ,  2 , . . .,   ]  and choose Equation ( 4) is plugged into (2) as The system can be decomposed into  mutual independent subsystems as The th actuator failure mathematic model can be modeled as where 0 ≤   ≤ 1 and   and   are uncertain constants.
When the constants   = 1 and   = V  , this indicates that the th actuator works normally (i.e., the actuators work in the failure-free case).Thus, the following 2 patterns of failures are considered.
(1) 0 ≤   ≤ 1: this case indicates that the systems lose partial performance during the operation, which is known as Partial Loss of Effectiveness (PLOE); that is,   =   V  .
(2)   = 0: this case implies that actuator output   is no longer affected by V  .V  indicates Total Loss of Effectiveness (TLOE); that is,   =   .
According to the above analysis, system mathematical model is rewritten as follows:

Design of Control Algorithm
In the failure of the period, the controller is designed as V  =   ,  = (, 1), and  = ( 1 ,  2 ) for any th subsystem, where  is designed as the finite-time stable nonsmooth control law [27].
On the basis of the above controller design, in order to guarantee the system stability, we must design  to meet the following formula: However, the failure model parameters of the actuator are unknown so that k is defined as the estimated value for  and k =  − k is defined.
The above analysis includes unknown seismic wave ẍ  disturbance, so subsequent analysis faces difficulty and challenge.Thus, the paper uses RBF neural network to approximate ẍ  .RBF network has characteristics of universal approximation.We use theory that uses RBF network to approximate ().The network algorithm is as follows: where  is an input of network,  is the th joint of network's hidden layer,  is the number of network's hidden layers, ℎ = [ℎ 1 , ℎ 2 , . . ., ℎ  ]  ,  * is the desirable permission of network,  is an approximation error of network, and  ≤   .
The input of network is  = [ 1  2 ]  .Then the output of network is as follows: According to RBF theory, we make the following definitions:  = [ Ḋ ], f() = Ŵℎ(), and () = ẍ  =  * ℎ().It is proved accordingly that the nonsmooth control law can make system globally finite-time stable.We can prove the following: the th subsystem of Lyapunov function is built as where Γ is definite matrix. > 0; W =  * − Ŵ.

Analysis of Numerical Simulation
The effectiveness of the finite-time stable nonsmooth control algorithm based on the building structural vibration of actuator failure is verified.A three-layer building structure is simulated by three control methods including nonsmooth control, LQR control, and no control.Each floor is equipped with actuators to provide control force resisting earthquake action for structure.And the system subjected to the earthquake wave called El Centro of external disturbance signal and 15% of the actuator failure after 3 seconds is assumed.Maximum of earthquake acceleration is  max = 3.417 m/s 2 .The parameters of finite-time stable nonsmooth control are  1 = 0.3,  2 = 0.46,  1 = 4, and  2 = 3.
The mass matrix, damping matrix, stiffness matrix, and position matrix of example 1 are as follows: (N/m) , In example 1, the contrast simulation curves of the displacement, velocity, acceleration response, and the control force for each floor are shown in Figures 1-4 under no control, LQR control, and nonsmooth control.
As is shown in Figures 1-4, nonsmooth control algorithm has been more effective than LQR control algorithm with actuator failure.The required control forces of two control methods have a little difference.However, nonsmooth control algorithm has been improved more than LQR control algorithm.In order to further analyze the effect of nonsmooth control, LQR control, and no control, the maximum displacement and maximum acceleration of each layer in the above simulation results are counted.The results are shown in Tables 1 and 2.
As is shown in Tables 1 and 2, compared with no control, the maximum displacement of the first, second, and third floor decreased by 85%, 88%, and 91% in LQR control.The maximum acceleration is also reduced by 23%, 8%, and 9%.Nevertheless, compared with LQR control, the maximum displacement of the first, second, and third floor is decreased by 74%, 77%, and 77% in nonsmooth control, respectively.And the maximum acceleration values are all reduced by 93%.] In example 2, the contrast simulation curves of the displacement, velocity, acceleration response, and the control force for each floor are shown in Figures 5-8 under no control, LQR control, and nonsmooth control.
As is shown in Figures 5-8, nonsmooth control algorithm is also more effective than no control and LQR control algorithms.At the same time, the maximum displacement and acceleration of each layer from the results of the second example are counted.The results are shown in Tables 3 and 4.
As is shown in Tables 3 and 4, compared with no control, the nonsmooth control declined 96%, 98%, and 98% in the maximum displacement of the first, second, and third floor.The maximum acceleration values are all reduced  nonsmooth control, structural vibration is suppressed effectively better than LQR control.And interstory displacement is controlled within a small range.The displacement, velocity, and acceleration tend to a small range of vibration better and to be stable lastly.Thus, nonsmooth control algorithm can better protect the building structure from damage of the earthquake compared with LQR control algorithm.

Conclusion
Aiming at the problem restraining nonlinear vibration of the building structure, a structure is mathematically modeled and analyzed.Then, according to the theory of finite-time stability and the analysis of actuator failure, nonsmooth control with RBF neural network is designed for the problem of structural vibration.And the stable analysis of the system is demonstrated.Finally, nonsmooth control, LQR control, and no control are compared by analysis.The control system is affected by seismic wave called El Centro.At the same time, the numerical simulation of the model with strong nonlinearity is studied.The above works verified the feasibility and effectiveness of nonsmooth control algorithm.In this paper, uncertainty and external perturbation estimation of the parameters are taken into account in the simulation.On this basis, further analyses of the systematic robustness and antijamming have theoretical and practical significance, which are worth studying further.

Table 1 :
Maximum displacement of each layer for example 1 (mm).

Table 2 :
Maximum acceleration of each layer for example 1 (m/s 2 ).

Table 3 :
Maximum displacement of each layer of example 2 (mm).

Table 4 :
Maximum acceleration of each layer of example 2 (m/s 2 ).