The metamorphic interaction between carbonate and silica-rich fluid is common in geological environments. The formation of talc from dolomite and silica-rich fluid occurs at low temperatures in the metamorphism of the CaO–MgO–SiO2–CO2–H2O system and plays important roles in the formation of economically viable talc deposits, the modification of dolomite reservoirs, and other geological processes. However, disagreement remains over the conditions of talc formation at low temperatures. In this study, in situ Raman spectroscopy, quenched scanning electron microscopy, micro-X-ray diffraction, and thermodynamic calculations were used to explore the interplay between dolomite and silica-rich fluids at relatively low temperatures in fused silica tubes. Results showed that talc formed at ≤200°C and low CO2 partial pressures (PCO2). The reaction rate increased with increasing temperature and decreased with increasing PCO2. The major contributions of this study are as follows: (1) we confirmed the formation mechanism of Mg-carbonate-hosted talc deposits and proved that talc can form at ≤200°C; (2) the presence of talc in carbonate reservoirs can indicate the activity of silica-rich hydrothermal fluids; and (3) the reactivity and solubility of silica require further consideration, when a fused silica tube is used as the reactor in high P–T experiments.
National Natural Science Foundation of China4123031241573054Knowledge Innovation ProgramSIDSSE-201302Hadal-trench Research ProgramXDB060601001. Introduction
The common metamorphic interaction between dolomite and silica-rich fluids plays important roles in many geological processes. For example, the interaction is closely associated with the formation of skarn ore deposits [1–3]. Talc was reported to form at low temperatures in the metamorphism of the CaO–MgO–SiO2–H2O–CO2 system [4–6]. Talc is characterized by a trioctahedron structure [7] and is chemically inert, soft, white, and highly thermally conductive [8]. As a result, talc is used in various industrial applications [7, 9, 10]. Previous studies showed that talc mineralization can occur in various geological settings, such as the alteration of ultra-mafic rocks (e.g., [11–15]), the mixing of seafloor hydrothermal fluids and seawater [16], and the alteration of Mg-carbonate rocks [17–21]. However, it is most economical to extract from deposits associated with the hydrothermal alteration of dolostone/Mg-carbonate [17].
Hydrothermal dolomite and hydrothermally altered dolomite are important hydrocarbon reservoirs (e.g., [22–25]). Geologically pervasive silica-rich hydrothermal fluids derived from sources, such as deep formation brines or magma intrusions (e.g., [26–28]), can react with dolomite to form talc in carbonate reservoirs, influencing the reservoirs’ physical properties [29–31]. In addition, talc has a low friction coefficient, so its formation along faults in carbonate rocks can promote the stable creep of a fault, releasing accumulated elastic strain and preventing strong earthquakes [32–35]. Therefore, thorough investigation of the CaMg(CO3)2–SiO2–H2O interaction can help elucidate many geological processes.
However, disagreements remained regarding the formation temperature of talc through the reaction between dolomite and a silica-rich fluid. The reaction has been theoretically calculated to occur at ≥150°C [5, 35, 36], but most geological studies have indicated that talc mainly forms at 250–400°C (e.g., [21, 37, 38]). For example, in the Saint-Barthélemy deposits in Switzerland, oxygen isotope thermometric calculations showed that talc mineralization occurred at about 300°C [21], which is consistent with fluid inclusion data (250–300°C) [39, 40]. Experimental studies have sought to construct a phase diagram of the CaO–MgO–SiO2–CO2–H2O system, but hydrothermal experimental studies have only been conducted above 250°C (e.g., [4, 41–44]). Consequently, further experiments at lower temperatures are necessary to fully explore the formation temperature of talc.
In this study, the reactions for the CaMg(CO3)2–SiO2–H2O system were conducted in fused silica tubes at temperatures from 100 to 200°C. In situ Raman spectroscopy was used to characterize the vapor products. The quenched solid products were investigated with Raman spectroscopy, scanning electron microscopy (SEM) equipped with an energy dispersive spectrometer (EDS), and micro-X-ray diffraction (micro-XRD). In addition, the Gibbs free energy of the reaction was also calculated using the geochemical modelling program.
2. Materials and Methods2.1. Sample Preparation
Dolomite powder was prepared from dolomite rocks of the Neoproterozoic Dengying Formation in the Sichuan Basin, Southwest China. Powder XRD analyses showed that the dolomite rock is comprised of >97% dolomite and <3% quartz. Calcite grains were prepared from colorless, transparent, rhombohedral calcite crystals. Distilled deionized water (18.2 KΩ·cm) was used throughout. Amorphous SiO2 originated from the fused silica tubes.
Chou et al. [46] have reported detailed procedures for constructing fused silica capillary capsules (FSCCs). The protective polyimide layer of the fused silica tube (0.5 mm in inner diameter and 0.65 mm in outer diameter) was burnt off in an oxyhydrogen flame, and one end of the tube was sealed. The dolomite/calcite powder and a 0.5-cm long water column were loaded into the tube and centrifuged to the sealed end. The open end was then connected to a pressure line. The air in the tube was evacuated, and the open end of the tube was sealed by fusion in the oxyhydrogen flame. As shown in Figure 1, the prepared FSCC is about 2 cm long and consists of the dolomite powder (~0.5 cm in length), water (~0.5 cm in length), and a vapor phase (~1 cm in length).
Setup for in situ analyses of the vapor phase within a FSCC containing dolomite and water.
High-pressure optical cells (HPOCs, Figure 2(a)) containing dolomite and water were also constructed for pressure measurements. The dolomite powder and deionized water were first loaded into a one-end-sealed fused silica tube (~20 cm in length). Approximately 2 cm long mercury was then injected to separate the reaction system and the pressurization medium—water. The detailed procedures for preparing HPOCs are described in Chou et al. [47].
(a) The setup for measurements of the internal pressures within a HPOC containing dolomite and water; (b) the batch stainless reactor in the oven. The left schematic diagram showing the structure of the reactor. SCR represents the stainless cup of the reactor, RC represents the reactor cover, IC represents internal cup, and CIC represents cover of the internal cup.
HPOC setup
2.2. Experimental Procedures2.2.1. In Situ Vapor-Phase Analyses
The reaction between dolomite and a silica-rich fluid to form talc involves decarbonation of dolomite and the generation of CO2:(1)3CaMgCO32+4SiO2+H2O⟶Mg3Si4O10OH2+3CaCO3+3CO2Raman spectroscopy is sensitive to CO2 and can detect CO2 at pressures lower than 0.6 bar [48, 49]. Therefore, in situ Raman spectroscopy of the vapor phase was used to detect the reaction. FSCCs containing dolomite and water were heated in a heating stage (Linkam CAP500) calibrated with a K-type thermocouple, which had been previously calibrated with the triple point (0°C) and boiling point (100°C) of water at 0.1 MPa. The temperature difference along the 4 cm central line of the heating stage was less than 0.5°C at 300°C. The setup of in situ Raman spectroscopic analysis is shown in Figure 1. The target temperature was increased at increments of 10°C from an initial 60°C, until a CO2 signal was detected in the vapor phase after heating for ~24 h. To characterize the mechanism of CO2 generation (metamorphic alteration or decomposition of dissolved CO32-), Raman spectra of the vapor phase within FSCCs containing calcite and water were also acquired for comparison.
Raman spectra were collected in situ for the vapor phase within FSCCs containing dolomite and water at 200°C (higher than the reaction threshold) to investigate the kinetics of the reaction. The experimental duration was increased from 2 h to ~240 h.
2.2.2. Pressure Measurements
The setup for the pressure measurement is shown in Figure 2(a). The HPOC containing dolomite and water was connected to a pressurization system. Pressures were monitored by a Setra 206D digital pressure transducer with Datum 2002 manometer (69 MPa full scale, accurate to ±0.14%). The HPOC containing dolomite and water was heated to 200°C using a Linkam CAP 500 heating stage. The position of mercury in the HPOC was fixed by adjusting the pressure with a pressure generator, and then the pressure of the whole system was recorded with experimental duration (Figure 2(a)).
2.2.3. Analyses of Solid Products
Several one-end-open fused silica tubes containing dolomite and water were placed in a 10 mL batch stainless steel reactor equipped with a Teflon (PTFE) internal cup (Figure 2(b)). The reactor was then heated at 150 and 200°C for 20–90 days in an oven with a temperature accuracy of ±5°C. During the reaction, the reactor was opened and the product CO2 was released several times to promote the reaction. After heating, micro-XRD and Raman spectroscopy were used to characterize the composition of the quenched solid product at room temperature. Then, the SEM was used to observe the morphology of the product. The chemical composition was analyzed using EDS.
2.3. Analytical Methods
Raman spectra were collected with a high-resolution Raman spectrometer (LabRAM HR800, JY/Horiba) using a 532.11 nm laser from an air-cooled, frequency-doubled Nd:YAG laser excitation, a 50x objective (Olympus), and a 1800 groove/mm grating with a spectral resolution of about 1 cm−1. An approximate 9.5 mW laser was focused on the central level of the horizontal tube for vapor spectra acquisition and on the surface of the solid phase for solid spectra acquisition. Spectra were collected from 100 to 1600 cm−1. To obtain a high signal-to-noise ratio spectrum, three accumulations were collected in denoise mode (120 s for the vapor phase and 30 s for the solid phase), and averaged for each spectrum. Before collection, the Raman spectrometer was calibrated with the v1 band of silicon at 520.2 cm−1 [50]. Labspec 5 software was used for Raman spectral analyses.
Micro-XRD investigations of the quenched reacted dolomite were carried out with a diffractometer (D/max Rapid II, Rigaku) equipped with a Mo tube and a 300-μm diameter collimator. The diffractometer was operated at 50 kV and 90 mA with an angular velocity of 6°/s and an exposure time of 15 min. Jade 6 software was used to characterize the compositions of the solid phase.
The morphology of the quenched reacted dolomite was observed using a field emission (FE) SEM (Supra55, Zeiss) with an accelerating voltage of 15 kV. The approximate chemical composition of the solid phase was analyzed by an EDS (Oxford Instruments, Inca X-Max 150 mm2). All experiments were performed at the Institute of Energy Sciences and the State Key Laboratory for Mineral Deposits Research hosted in School of Earth Sciences and Engineering, Nanjing University.
In addition, we calculated the Gibbs free energy of talc formation from the CaMg(CO3)2–SiO2(aq)–H2O system for the P–T conditions covered in these experiments, using the Hch program (version 4.4) and its incorporated Unitherm database [51].
3. Results3.1. Vapor-Phase Characterization
The linear CO2 molecule has four vibrational modes: a symmetric stretching mode (v1), two bending modes (2v2: v2a and v2b), and an antisymmetric stretching mode (v3) (e.g., [48, 52, 53]). The modes v1 and 2v2 are both Raman active and have a similar energy (~1335 cm−1) and the same symmetry species, resulting in a Fermi resonance [48]. Fermi resonance causes the excited admixed states to split into two prominent peaks: an upper band at ~1388 cm−1 and a lower band at ~1285 cm−1 [48, 54]. Weak hot bands flanking the Fermi diads may also appear in the spectrum [48]. Raman spectroscopy has very low detection limits for CO2 and thus is used frequently for CO2 characterization in fluid inclusions [53, 55–58].
Figure 3(a) shows the Raman spectra of the vapor phase in FSCCs containing CaMg(CO3)2–H2O and CaCO3–H2O after heating at 90–150°C for 24 h. For the FSCCs containing dolomite and water, no CO2 signal was observed after heating at ≤90°C. Weak but clear CO2 Fermi bands at ~1285 and 1384 cm−1 were observed after heating at 100°C. The Raman intensity of CO2 was much stronger after heating at 150°C than that at 100°C (Figure 3(a)). That is to say, CO2 was generated in the CaMg(CO3)2–SiO2–H2O system when heated at ≥100°C with an experimental duration of 24 h. However, the signals of CO2 were not observed in FSCCs containing calcite and water after heating at 100–200°C for 24 h. Considering that a greater concentration of CO32- dissolved from calcite than from dolomite in pure water at temperatures of 100–150°C [59, 60], we suggest that the CO2 from the dolomite-bearing system was generated by decarbonation via metamorphic reaction (1) instead of the decomposition of dissolved CO32-.
Raman spectra of the vapor phase in FSCCs containing (a) CaCO3–H2O and CaMg(CO3)2–H2O after heating at 90–150°C for 24 h and (b) CaMg(CO3)2–H2O after heating at 200°C from 2 to 41 h.
The intensity and wavenumber of the CO2 Fermi diad bands vary with changes in the CO2 pressure and temperature [48, 53, 56]. Previous studies have suggested that the Fermi diad splits increase with increasing CO2 pressure at a constant temperature (e.g., [61]). Accordingly, several equations were constructed for quantitative measurements of the CO2 density based on the Fermi diad splits by using reference samples with PCO2 > 0.6 bar ([49] and references therein). In this study, the Fermi diad peak positions and splits of CO2 produced from CaMg(CO3)2–SiO2–H2O interaction were also obtained (Table 1). However, negative density values were obtained when applying these calibration curves to quantitatively measure the CO2 content in the FSCC. This result indicates that only a small amount of CO2 was produced in the FSCC and that the CO2 pressure was lower than 0.6 bar. Table 2 shows the variation of the internal pressure of a HPOC containing dolomite and water with experimental duration. Results showed that the internal pressure fluctuated with reaction time. Consequently, the exact partial pressure of CO2 generated from the metamorphic reaction (1) cannot be obtained; this should also result from the very low PCO2.
Fermi diad bands, splits, and peak areas of CO2 generated in the FSCC containing dolomite and water at 200°C, and the calculated degree of reaction.
Reaction time (h)
Fermi diads and splits (cm−1)
Peak area
Degree of reaction (%)a
v1
v2
Δ
v1
v2
v1+v2
0
—
—
—
0
0
0
0
2
1285.21
1387.92
102.71
315.87
366.62
682.49
15.8
4
1285.19
1387.77
102.58
530.83
775.21
1306.04
30.2
6
1285.09
1387.7
102.61
551.64
817.14
1368.78
31.6
8
1285.14
1387.72
102.58
599.66
955
1554.66
35.9
10
1284.84
1387.49
102.65
731.41
1023.21
1754.62
40.6
20
1285.51
1388.04
102.53
900.65
1419.02
2319.67
53.6
22
1285.45
1388
102.55
1000.18
1483.36
2483.54
57.4
28
1285.37
1387.95
102.58
1155.19
1718.56
2873.75
66.4
40
1285.43
1387.98
102.55
1327.9
1910.84
3238.74
74.8
43
1285.66
1388.21
102.55
1270.99
1887.07
3158.06
73.0
46
1285.76
1388.23
102.47
1388.06
1995.8
3383.86
78.2
49
1285.63
1388.17
102.54
1346.42
1921.19
3267.61
75.5
60
1285.39
1387.94
102.55
1370.6
2163.74
3534.34
81.7
65
1285.62
1388.16
102.54
1433.07
2208.62
3641.69
84.2
70
1285.59
1388.14
102.55
1454.65
2172.31
3626.96
83.8
87
1285.01
1387.57
102.56
1561.79
2307.84
3869.63
89.4
92
1285.49
1387.93
102.44
1623.26
2288.82
3912.08
90.4
104
1285.73
1388.11
102.38
1713.6
2457.37
4170.97
96.4
137
1285.67
1388.04
102.37
1729.76
2589.05
4318.81
149
1285.26
1387.99
102.73
1746.57
2501.63
4248.2
159
1285.38
1387.97
102.59
1836.27
2553.95
4390.22
171
1285.31
1387.93
102.62
1797.81
2599.46
4397.27
193
1285.24
1387.77
102.53
1697.12
2681.04
4378.16
203
1285.37
1387.95
102.58
1755.2
2555.08
4310.28
213
1285.66
1388.21
102.55
1740.85
2548.89
4289.74
224
1285.6
1388.15
102.55
1725
2559.7
4284.7
Thea total Raman peak area of CO2 at equilibrium state is an average of those after reaction for ~120 h. Then, the degree of reaction can be regarded as 100% when the reaction time exceeds 120 h.
Variations in the internal pressures of the HPOC containing dolomite and water with experimental duration at 200°C.
t (h)
P (psi)
0
209
3
221
6.3
224
9.2
223
12.2
224
22.2
210
25
215
28.5
215
32.5
215
34.6
216
46.3
217
49.2
217
52.9
219
58.9
219
70.4
221
73.6
221
76.8
223
79.7
224
82.9
227
94.3
222
97.3
212
99.9
218
107.5
206
127.6
208
The variation in the Raman intensity of CO2 as a function of the experimental duration can reflect the kinetics of reactions yielding CO2 [57]. Increasing the experimental duration could increase the CO2 intensity (Figure 3(b)). The peak areas of the CO2 Fermi diad bands increased with experimental duration up to about 120 h (200°C) before eventually leveling off (Figure 4, Table 1). Solid-phase characterization (see Section 3.2) indicated that the dolomite was unlikely to run out over the length of the experiment. Consequently, the reaction reached an equilibrium state after reaction for ~120 h. The degree of the reaction (R) can be calculated using the ratio between the total Raman peak area of CO2 at time t (A) and that at equilibrium state (A∗):(2)R%=AA∗×100%.As shown in Figure 4 (diamonds), the slope of R decreases with the increase of reaction time, indicating that the reaction rates decrease with the increase of experimental duration/PCO2. The results also showed that the reaction rate increased with increasing temperature. For example, the Raman intensity of CO2 was stronger at higher temperature within a given period of time (Figure 3(a)).
Raman peak areas of CO2 and the degree of reaction versus reaction time at 200°C. Black rectangles and red circles denote the peak areas of the lower band at ~1285 cm−1 and the upper band at ~1385 cm−1, respectively. Blue triangles represent the total peak areas of both bands. The green diamonds represent the degree of the reaction. Data plotted are from Table 1.
3.2. Solid-Phase Characterization
Figure 5 shows XRD patterns of the quenched solid relicts in the fused silica tubes. After heating at 200°C for ~20 days, the talc signals were weak. However, heating for 80 days produced calcite and talc as the main phases in the solid relicts, whereas dolomite signals were hardly visible in the XRD pattern (Figure 5).
X-ray patterns of the solid relicts in FSCCs containing dolomite and water after heating at 150°C for ~40 days (lower blue line) and at 200°C for ~20 days (middle orange line) and ~80 days (upper black line).
The Raman spectrum of the solid phase before heating (Figure 6) showed only dolomite peaks (~177, 300.5, 1098 cm−1; [62]), indicating that the dolostone was of high purity, consistent with the XRD analysis. However, in addition to dolomite, characteristic calcite signals (~282 and 1086 cm−1; [63]) and talc signals (190.5, 360.5, and 675 cm−1; [64]) appeared after heating at 200°C for 60 days.
Raman spectrum of solid relicts after heating at 200°C for 60 days. The reference spectra of dolomite, calcite, and talc were also shown for comparison. The dolomite spectrum was acquired from the sample before heating. The calcite spectrum was acquired from crystalline calcite, and the reference spectrum of talc was cited from an open database hosted by the Department of Geosciences at the University of Arizona (RRUFF Project, http://rruff.info/index.php).
Figure 7 shows the morphology of the solid phase after heating at 200°C for 60 days. The solid phase has a honeycomb-like texture and was widely distributed in the relicts (Figures 7(a)–7(d)). It was identified by EDS as talc (Figure 7(c)). The talc exhibited unoriented textures because it formed under strain-free conditions [21]. Some cylindrical talc also occurred along the inner surface of the FSCC (Figure 7(d)). The dolomite grains had smooth edges (Figure 7(c)), indicating dissolution during heating. Some products of rhombohedral calcite (Figure 7(d)) were also present in the solid phase, which formed along with the talc via reaction (1).
SEM micrographs and EDS analyses of the solid relicts in an FSCC containing dolomite and water after heating at 200°C for ~60 days. (a, b) Honeycomb-like talc; (c) dolomite grains with smooth edges and EDS result of talc (yellow arrow); (d) euhedral calcite formed in the relicts (white arrow) and cylindrical talc growing on the inner surface of the tube (yellow arrow).
The amount of Mg-silicate mineral produced at 150°C for 40 days was below the detection limit of the micro-XRD equipment. Only dolomite and a small amount of calcite were observed in the XRD pattern after heating at 150°C for 40 days (Figure 5). This further supports the view that the metamorphic reaction rate is largely dependent on temperature. Some researchers view talc as the initial metamorphic mineral for the CaMg(CO3)2–SiO2–H2O system (e.g., [4–6]). However, serpentine minerals, like lizardite and chrysotile, are also likely to form at low temperatures during metamorphism of the CaO–MgO–SiO2–H2O–CO2 system, especially in contact or regional metamorphic settings [65–67]. Some researchers have even pointed out that serpentine forms at lower temperatures than talc during metamorphism of the MgO–SiO2–H2O–CO2 system [68, 69]. In fact, while serpentine is likely to form in a low-silica environment, further introduction of SiO2 will make talc stable relative to serpentine [70–73]. Considering the fact that talc was characterized as the product of Mg-silicate mineral in the 200°C experiment via reaction (1), we speculate that, while not detected by XRD, talc also formed below 200°C since CO2 was generated during the experiment (see above).
3.3. Thermodynamic Calculations
Due to the limits of the Unitherm database, we used aqueous silica as the SiO2 species that participated in the reaction. Considering that the solubility of amorphous silica was high at elevated temperatures [74], the calculated results should approximate the conditions of the experiments. The Gibbs free energy (ΔG) of formation for talc from CaMg(CO3)2, aqueous SiO2, and H2O at the pressure and temperature of interest are given in Table 3. The ΔG of reaction decreases with increasing temperature at the saturation pressure. This indicates that the reaction is more favorable at higher temperatures. The ΔG becomes negative at T≥80°C, which implies that the formation of product talc from dolomite and a silica-rich fluid is thermodynamically favored. However, this reaction may not commence until even higher temperatures are reached due to the probable initial kinetic barrier to the reaction. These thermodynamic calculations support the implication from the experimental results that talc formation can occur at temperatures above 100°C.
The Gibbs free energies of the reaction 3CaMg(CO3)2 + 4SiO2(aq) + H2O = Mg3(Si4O10)(OH)2 + 3CaCO3 + 3CO2 at the temperatures of interest and their corresponding saturation pressures.
Temperature (°C)
ΔGa (kJ/mol)
Psatb (bar)
Temperature (°C)
ΔG (kJ/mol)
Psat (bar)
25
7.709
0.032
100
–7.083
1.014
50
4.663
0.124
110
–9.951
1.434
60
2.771
0.199
120
–12.938
1.987
70
0.609
0.312
130
–16.032
2.703
80
–1.778
0.474
140
–19.223
3.615
90
–4.351
0.702
150
–22.502
4.761
ΔGa refers to the Gibbs free energy of the reaction; Psatb represents the corresponding saturation pressures, which are calculated based on the thermodynamic model proposed by Zhang and Duan [45].
4. Discussion4.1. Implications for the Formation of Mg-Carbonate-Hosted Talc
Geologically, Prochaska [18] grouped the talc deposits into five types: (1) talc related to ultramafics (e.g., [13–15]); (2) Mg-carbonate-hosted talc (e.g., [20, 37]); (3) metamorphic talc (e.g., [75, 76]); (4) talc related to banded iron formations (mostly minnesotaite; [77, 78]); and (5) secondary talc deposits [18]. The most economically viable of these deposits are usually related to the metamorphic reaction between an Mg-carbonate infiltrated by a silica-rich hydrothermal fluid [18, 20, 21, 37]. Intense fractures that increase the permeability of geological fluid flow generally develop near such deposits [18, 20, 21, 37, 38].
Investigating the formation temperature of talc can improve our understanding of its mineralization process. This has previously been done using several methods. These include microthermometric measurements of relevant fluid inclusions (e.g., [39, 40, 79]) and calculations using talc–dolomite oxygen isotope thermometry, assuming that the mineral pairs achieve oxygen isotope equilibrium [21, 36]. In addition, the phase diagram of the CaO–MgO–SiO2–CO2–H2O system has often been referred to for evaluating the formation temperature of talc [5, 35]. The diagram was established based on hydrothermal experiments, geological case studies, and thermodynamic calculations [4, 5, 43, 44]. However, the experiments used to chart out this system have been generally conducted at >250°C [4, 41–44]. The reaction path of the phase diagram at low temperatures was mainly established through thermodynamic calculations implying the need for talc forming experiments at temperatures below 250°C.
Some geological case studies attribute low talc mineralization temperatures (<200°C) derived from adjacent talc and dolomite oxygen isotope thermometry, to actually reflect isotopic disequilibrium [36]. This study shows that talc deposits can still form at temperatures below 200°C on geological time scales, especially if the product CO2 can be released (cf. reaction (1)). However, large-scale talc mineralization is more likely to form at higher temperatures (e.g., 250–400°C). Firstly, PCO2 controls the lower thermal limit of talc stability. The onset temperature of the transformation increases with increasing PCO2, because CO2 is a product of the metamorphic reaction (1) and its presence greatly decreases the solubility of SiO2 in the fluid [80]. CO2 is a common component in geological fluids and can be either released from magmas (e.g., [81–84]) or generated from the hydrothermal alteration of carbonate (e.g., [85–87]). The oxidation (e.g., [88]) and hydrothermal maturation of organic matter are also natural sources of CO2 [89, 90]. Therefore, talc mineralization should occur at relatively high temperatures in the presence of CO2. Secondly, as our results have shown, the reaction rate for reaction (1) increases sharply with increasing temperature, facilitating talc deposits to form at higher temperatures.
This study can also contribute to understanding the fault weakening mechanism in the upper crust. The elastic strain accumulation along a fault can be released through a sudden seismic slip (earthquake) or aseismic creep slip [32]. A lower frictional coefficient for a fault will facilitate stable creep, weakening the fault and suppressing the occurrence of strong earthquakes [35]. The frictional coefficient of a fault generally decreases with increasing temperature [35]. Therefore, faults are likely to be weakened due to high temperatures in the deep crust, but not in the cool shallow crust. The pervasive distribution of clay minerals along faults has also been thought to weaken faults [33–35, 91–94], because layered clay minerals exhibit much lower frictional coefficients than other minerals [95]. For example, talc discovered along the San Andreas fault zone is responsible for helping in aiding slippage along the fault [35, 95]. As shown here, dolomite could react at ≤200°C with silica-rich fluids traveling along fault planes to form talc and hence might be an important mechanism of fault weakening in carbonate sequences in the upper crust.
4.2. Implications for Hydrothermal Dolomite Reservoir Research
Carbonate rock is the main type of hydrocarbon reservoir worldwide, hosting over 60% of petroleum reserves [31]. Dolomite hydrocarbon reservoirs are important, comprising about half of the carbonate hydrocarbon reservoirs worldwide [96]. Recent research has suggested that hydrothermal alteration can increase the porosity and permeability of dolomite reservoirs substantially and is an important factor affecting the development and distribution of dolomite reservoirs [24, 25, 97–101]. The Tarim basin is one of the most important petroliferous basins in China and contains a lower Palaeozoic carbonate series, which is also an important hydrocarbon reservoir. Recent exploration has shown that silica-rich hydrothermal fluids have infiltrated these carbonate series, improving the physical properties of the reservoirs considerably (e.g., the Shunnan area of the Tarim Basin; [102, 103]). It has been proposed that silica-rich hydrothermal fluids were transported through extensional faults from the deep strata to the shallow carbonate sequence, where they migrated laterally through porous and permeable carbonate formations (~6670 m in the Shunnan area; [104]). Hydrothermal fluids originating in deep basins are generally hot. Microthermometric measurements have indicated that the silica-rich hydrothermal fluids in the Tarim basin reach over 200°C [101, 103]. Given that the lower part of the lower Palaeozoic sequence is mainly composed of dolomite, silica-rich hydrothermal fluids could react with the dolomite to form talc and thus change the physical properties of the reservoir. Recently, petrologic and diagenetic research have revealed pervasive silicification in Early Cretaceous ultra-deep water carbonate reservoirs in the Atlantic Ocean, offshore from Brazil [105]. The presence of talc, calcite, quartz, and dolomite on the thin-section scale may indicate that the dolomite was strongly corroded by a silica-rich hydrothermal fluid.
Alteration of dolomite to talc will also modify the porosity and permeability of carbonate hydrocarbon reservoirs [29–31]. The silica required for the mineral alteration can be provided by either silica-rich hydrothermal fluids or silica (e.g., quartz, chert, and opal) within the carbonate reservoirs [106]. If SiO2 derives from quartz/chert in the dolomite sequences, the hydrothermal alteration would increase the porosity of the dolomite reservoirs. McKinley et al. [29] reported that the total volume of minerals within a dolomite reservoir can be reduced by 13% to 17% through the reaction between dolomite and quartz in reaction (1). In addition, the reaction between dolomite and silica-rich hydrothermal fluids can act as an important source of CO2 in hydrocarbon reservoirs. The presence of CO2 can lower the pH of the formation water and thus promote the dissolution of carbonate minerals [60, 107, 108], increasing the porosity of the reservoirs [109–111]. However, the pore throats may be blocked by the formation of talc or other clay minerals [29, 112]. Therefore, more detailed factors should be considered in order to unequivocally evaluate the effects of silica-rich hydrothermal fluids in dolomite reservoirs.
Although talc can form from the interaction between dolomite and silica-rich fluids at low temperatures, it is seldom observed in hydrocarbon reservoirs [29, 31] for the following two reasons. (1) A large amount of CO2 can be produced by the maturation of organic matter and the reaction between carbonate minerals and organic acid [98, 101]. The presence of CO2 decreases the lower thermal stability field of talc [113]. (2) The reaction path is dependent on the composition of the hydrothermal fluid. For example, K+ and Al3+ are also important components of geological fluids. Montmorillonite instead of talc is more likely to form in the presence of only a small quantity of Al3+ [41], and the formation of talc can also be inhibited by K+ [29].
4.3. Implications for High P–T Experiment Using Fused Silica Capillary Tubes as Reactors
FSCCs are used to construct synthetic fluid inclusions containing organic and inorganic components [46]. They offer advantages such as being inert to many components, especially acids and S, allowing for the convenient synthesis of fluid inclusions, and facilitating in situ optical and Raman spectroscopic observations (e.g., [57, 114–117]). Fused silica tubes can tolerate relatively high temperatures up to 600°C and pressures up to 300 MPa. As a result, FSCCs are used in many research fields. For example, in addition to construction of synthetic fluid inclusions [46, 53, 118], FSCCs were used in studying the properties of hydrothermal fluids as optical and Raman spectroscopic cells [115–117, 119–121]. FSCCs were also used as reactors in investigating the mechanism of thermochemical sulfate reduction [114] and the decomposition of organic matter [57].
However, SiO2 in the FSCC acted as a reagent in this study and was partially dissolved, as indicated by the pits on the inner surface of the tube (Figures 8(a)–8(d)). The dissolution of silica from FSCCs containing alkali sulfate solutions was also observed after quenching from ≥350°C (Figures 8(e) and 8(f)). The severe dissolution of fused silica can be ascribed to three factors. (1) Amorphous silica is more soluble than quartz, especially at high temperatures. In neutral solutions, its solubility increases sharply with temperature from 100 ppm at 20°C to 1500 ppm at 310°C [74, 122, 123]. (2) Under basic conditions, the solubility of amorphous silica is greatly enhanced by the ionization of silicic acid (H4SiO4 + OH− → H3SiO4- + H2O; [124]). (3) SiO2 may act as a reagent as it did in this experiment. The presence of dissolution pits will weaken the mechanical strength of the silica tube. In addition, the presence of dissolved silica can make the system more complicated than expected. Therefore, the solubility and reactivity of silica under hydrothermal conditions should be evaluated before FSCCs are used as reactors.
SEM images of the inner surface of the silica tube. (a) Smooth inner surface before the reaction; (b) magnification of the square area shown in (a); (c) dissolution pits on the inner surface after heating at 200°C for ~60 days; (d) magnification of (c); severe erosion of the silica on the inner surface of FSCCs containing (e) 1.0 m Na2SO4 and (f) 1.0 m Li2SO4 after heating at 350°C for 1 h.
5. Conclusion
The reactions in the CaMg(CO3)2–SiO2–H2O system at low temperatures were investigated using fused silica tubes as reactors. Results showed that dolomite reacted with a silica-rich fluid to form talc, calcite, and CO2 at ≤200°C and low PCO2. The reaction rate increased with increasing temperature and decreased with rising PCO2. Therefore, high temperature and the presence of a conduit to release CO2 will promote the formation of talc. This experiment has important geological and geochemical implications.
(1) The results confirmed the mechanism of talc mineralization in Mg-carbonate hosted talc deposits. Dolomite reacted with silica-rich hydrothermal fluids to form talc, calcite, and CO2. Talc could form at ≤200°C, whereas previous hydrothermal experiments examining the CaO–MgO–SiO2–CO2–H2O system were mainly conducted at >250°C. However, considering the effect of temperature on the reaction rate, and other geological conditions, massive talc deposits are still more likely to form at higher temperatures. The formation of talc along a fault in a Mg-carbonate formation will also weaken the fault, thus preventing strong earthquakes.
(2) Talc in carbonate reservoirs can indicate the activity of silica-rich hydrothermal fluids. Fluid-aided alteration of dolomite can change the physical properties of dolomite reservoirs substantially. The reaction between dolomite and quartz within the carbonate can decrease the total volume of minerals by 13%–17%. The generation of CO2 can promote the dissolution of carbonate minerals elsewhere under the appropriate conditions, increasing the porosity and permeability of carbonate reservoirs. However, talc minerals may block pore throats in the reservoirs. Therefore, additional factors need to be considered when evaluating the effects of CaMg(CO3)2–SiO2–H2O interactions on the physical properties of carbonate reservoirs.
(3) The solubility and reactivity of silica should be considered when using fused silica tubes as reactors in high P–T experiments. The dissolution of silica will increase the complexity of the system and weaken the mechanical strength of the tube.
Conflicts of Interest
The authors declare that they have no conflicts of interest.
Acknowledgments
The dolomite sample was provided by Mr. Chunhua Shi. Misses Yang Qu, Wanlu Gao, and Ye Qiu helped the authors a lot during the micro-XRD analysis and HPOC experiment. Dr. Rui Wang and Miss Siyu Hu are also thanked for their help in the thermodynamic calculations of the reactions. This work was financially supported by the National Natural Science Foundation of China (Grant nos. 41230312 and 41573054). I-Ming Chou is thankful for the support of the Knowledge Innovation Program (SIDSSE-201302) and the Hadal-trench Research Program (XDB06060100) of Chinese Academy of Sciences.
MeinertL. D.Skarns and skarn deposits19921941451622-s2.0-0027084433MeinertL. D.DippleG. M.NicolescuS.World skarn deposits2005299336YaoY.ChenJ.LuJ.WangR.ZhangR.Geology and genesis of the Hehuaping magnesian skarn-type cassiterite-sulfide deposit, Hunan Province, Southern China201458C1631842-s2.0-8489256098810.1016/j.oregeorev.2013.10.012GordonT. M.GreenwoodH. J.The reaction dolomite + quartz + water = talc + calcite + carbon dioxide197026822524210.2475/ajs.268.3.225HolnessM. B.Fluid flow paths and mechanisms of fluid infiltration in carbonates during contact metamorphism: The Beinn an Dubhaich aureole, Skye199715159702-s2.0-003090690110.1111/j.1525-1314.1997.00005.xHeinrichW.ChurakovS. S.GottschalkM.Mineral-fluid equilibria in the system CaO–MgO–SiO2–H2O–CO2–NaCl and the record of reactive fluid flow in contact metamorphic aureoles2004148213114910.1007/s00410-004-0598-72-s2.0-7744221555WesołowskiM.Thermal decomposition of talc: a review1984781-339542110.1016/0040-6031(84)87165-82-s2.0-0001224166Pérez-MaquedaL. A.DuranA.Pérez-RodríguezJ. L.Preparation of submicron talc particles by sonication2005281-42452552-s2.0-1104423836710.1016/j.clay.2004.01.012JohnsonR. L.Talc199271818820JohnsonR. L.VirtaR. L.Talc2000797981AbzalovM. Z.Chrome-spinels in gabbro-wehrlite intrusions of the Pechenga area, Kola Peninsula, Russia: emphasis on alteration features19984331091342-s2.0-003172085410.1016/S0024-4937(98)00005-XEl-SharkawyM. F.Talc mineralization of ultramafic affinity in the Eastern Desert of Egypt20003543463632-s2.0-003417681210.1007/s001260050246FranceschelliM.CarcangiuG.CareddaA. M.CrucianiG.MemmiI.ZuccaM.Transformation of cumulate mafic rocks to granulite and re-equilibration in amphibolite and greenschist facies in NE Sardinia, Italy2002631-21182-s2.0-003607869310.1016/S0024-4937(02)00121-4TesalinaS. G.NimisP.AugéT.ZaykovV. V.Origin of chromite in mafic-ultramafic-hosted hydrothermal massive sulfides from the Main Uralian Fault, South Urals, Russia2003701-239592-s2.0-014207261510.1016/S0024-4937(03)00090-2EvansD. M.Metamorphic modifications of the Muremera mafic-ultramafic intrusions, eastern Burundi, and their effect on chromite compositions201510119342-s2.0-8490777834010.1016/j.jafrearsci.2014.09.004YamanakaT.MaetoK.AkashiH.IshibashiJ.-I.MiyoshiY.OkamuraK.NoguchiT.KuwaharaY.TokiT.TsunogaiU.UraT.NakataniT.MakiT.KubokawaK.ChibaH.Shallow submarine hydrothermal activity with significant contribution of magmatic water producing talc chimneys in the Wakamiko Crater of Kagoshima Bay, southern Kyushu, Japan201325874842-s2.0-8487791926310.1016/j.jvolgeores.2013.04.007MoineB.FortuneJ. P.MoreauP.ViguierF.Comparative mineralogy, geochemistry, and conditions of formation of two metasomatic talc and chlorite deposits: Trimouns, Pyrenees, France, and Rabenwald, eastern Alps, Austria19898451398141610.2113/gsecongeo.84.5.13982-s2.0-0024873273ProchaskaW.Geochemistry and genesis of Austrian talc deposits1989455115252-s2.0-002485734710.1016/0883-2927(89)90008-5de ParsevalP.JiangS.FontanF.WangR.MartinF.FreeetJ.Geology and ore genesis of the Trimouns talc-chlorite ore deposit, Pyrénées, France20042048778862-s2.0-84977988651GondimA. C.JiangS.Geologic characteristics and genetic models for the talc deposits in Paraná and Bahia, Brazil20042048298362-s2.0-84978010241BoulvaisP.de ParsevalP.D’HulstA.ParisP.Carbonate alteration associated with talc-chlorite mineralization in the eastern Pyrenees, with emphasis on the St. Barthelemy Massif2006883-449952610.1007/s00710-006-0124-x2-s2.0-33750444637DaviesG. R.SmithL. B.Jr.Structurally controlled hydrothermal dolomite reservoir facies: an overview200690111641169010.1306/052206051642-s2.0-33751504921LonneeJ.MachelH. G.Pervasive dolomitization with subsequent hydrothermal alteration in the Clarke Lake gas field, Middle Devonian Slave Point Formation, British Columbia, Canada20069011173917612-s2.0-3375152491010.1306/03060605069LuczajJ. A.Evidence against the Dorag (mixing-zone) model for dolomitization along the Wisconsin arch - A case for hydrothermal diagenesis20069011171917382-s2.0-3375154223110.1306/01130605077SmithL. B.Jr.Origin and reservoir characteristics of Upper Ordovician Trenton-Black River hydrothermal dolomite reservoirs in New York20069011169117182-s2.0-3375154374110.1306/04260605078ParnellJ.Devonian Magadi-type cherts in the Orcadian Basin, Scotland198656449550010.1306/212F8968-2B24-11D7-8648000102C1865D2-s2.0-0022851336García-RuizJ. M.Carbonate precipitation into alkaline silica-rich environments19982698438462-s2.0-8487495690210.1130/0091-7613(1998)026<0843:CPIASR>2.3.CO10.1130/0091-7613(1998)026<0843:CPIASR>2.3.CO;2ZhangJ.HuW.QianY.WangX.CaoJ.ZhuJ.LiQ.XieX.Formation of saddle dolomites in Upper Cambrian carbonates, western Tarim Basin (northwest China): implications for fault-related fluid flow20092681428144010.1016/j.marpetgeo.2009.04.0042-s2.0-67650217556McKinleyJ. M.WordenR. H.RuffellA. H.Contact diagenesis: the effect of an intrusion on reservoir quality in the triassic sherwood sandstone group, Northern Ireland200171348449510.1306/2DC40957-0E47-11D7-8643000102C1865D2-s2.0-14344284948DongS.ChenD.QingH.ZhouX.WangD.GuoZ.JiangM.QianY.Hydrothermal alteration of dolostones in the Lower Ordovician, Tarim Basin, NW China: multiple constraints from petrology, isotope geochemistry and fluid inclusion microthermometry20134627028610.1016/j.marpetgeo.2013.06.0132-s2.0-84881109947MadrucciV.AnjosC. W. D. D.SpadiniR. A.AlvesD. B.AnjosS. M. C.Authigenic magnesian clays in carbonate reservoirs in BrazilProceedings of the 15th International Clay Conference2013Rio De Janeiro, BrazilScholzC. H.Earthquakes and friction laws1998391666237422-s2.0-003191397010.1038/34097SchleicherA. M.Van Der PluijmB. A.SolumJ. G.WarrL. N.Origin and significance of clay-coated fractures in mudrock fragments of the SAFOD borehole (Parkfield, California)200633162-s2.0-3384566946910.1029/2006GL026505L16313SchleicherA. M.van der PluijmB. A.WarrL. N.Nanocoatings of clay and creep of the San Andreas fault at Parkfield, California20103876676702-s2.0-7795596953910.1130/G31091.1CollettiniC.VitiC.SmithS. A. F.HoldsworthR. E.Development of interconnected talc networks and weakening of continental low-angle normal faults20093765675702-s2.0-6964909970410.1130/G25645A.1TornosF.SpiroB. F.The geology and isotope geochemistry of the talc deposits of Puebla de Lillo (Cantabrian zone, northern Spain)2000956127712962-s2.0-0033676939HechtL.FreibergerR.GilgH. A.GrundmannG.KostitsynY. A.Rare earth element and isotope (C, O, Sr) characteristics of hydrothermal carbonates: genetic implications for dolomite-hosted talc mineralization at Gopfersgrun (Fichtelgebirge, Germany)19991551-211513010.1016/S0009-2541(98)00144-22-s2.0-0033102647SharmaR.JoshiP.PantP. D.The role of fluids in the formation of talc deposits of Rema area, Kumaun Lesser Himalaya20097322372482-s2.0-6274910756810.1007/s12594-009-0080-2De ParsevalP.MoineB.FortunéJ. P.FerretJ.Fenoll Hach-AliP.Torrez-RuizJ.GervillaF.Fluid-mineral interactions at the origin of the Trimouns talc and chlorite deposit (Pyrénées, France)1993Granada, SpainUniversity of Granada, Granada205209BoironM. C.BoulvaisP.CathelineauM.BanksD.CalvayracN.HubertG.Fluid circulation at the origin of the trimouns talc deposit (Pyrenees, France)Proceedings of the 18th Meeting of European Current Research on Fluid Inclusions2005Siena, ItalyBaylissP.LevhinsonA. A.Low temperature hydrothermal synthesis from dolomite or calcite, quartz and kaolinite19711921091142-s2.0-3534898615110.1346/CCMN.1971.0190207SkippenG.An experimental model for low pressure metamorphism of siliceous dolomitic marble1974274548750910.2475/ajs.274.5.487SlaughterJ.KerrickD. M.WallV. J.Experimental and thermodynamic study of equilibria in the system CaO–MgO–SiO2–H2O–CO2197527514316210.2475/ajs.275.2.143EggertR. G.KerrickD. M.Metamorphic equilibria in the siliceous dolomite system: 6 kbar experimental data and geologic implications1981457103910492-s2.0-001970927410.1016/0016-7037(81)90130-7ZhangZ.DuanZ.Prediction of the PVT properties of water over wide range of temperatures and pressures from molecular dynamics simulation20051493-43353542-s2.0-1494434445610.1016/j.pepi.2004.11.003ChouI.-M.SongY.BurrussR. C.A new method for synthesizing fluid inclusions in fused silica capillaries containing organic and inorganic material20087221521752312-s2.0-5324910526310.1016/j.gca.2008.07.030ChouI.-M.BurrussR. C.LuW. J.ChenJ.WangY.DuffyT. S.ShenG.DobrzhinetakayaL. F.A new optical cell for spectroscopic studies of geologic fluids at pressures up to 100 MPa2005Amsterdam, NetherlandsElsevier475485RossoK. M.BodnarR. J.Microthermometric and Raman spectroscopic detection limits of CO2 in fluid inclusions and the Raman spectroscopic characterization of CO2199559193961397510.1016/0016-7037(95)94441-H2-s2.0-0029535430LamadridH. M.2016Blacksburg, VA, USAVirginia Polytechnic Institute and State UniversityParkerJ. H.FeldmanD. W.AshkinM.Raman scattering by silicon and germanium196715537127142-s2.0-3604905498510.1103/PhysRev.155.712ShvarovY. V.Algorithmization of the numeric equilibrium modeling of dynamic geochemical processes19993765715762-s2.0-0001582484WrightR. B.WangC. H.Density effect on the Fermi resonance in gaseous CO2 by Raman scattering19735872893289510.1063/1.16795942-s2.0-0001618208WangX.ChouI.-M.HuW.BurrussR. C.SunQ.SongY.Raman spectroscopic measurements of CO2 density: experimental calibration with high-pressure optical cell (HPOC) and fused silica capillary capsule (FSCC) with application to fluid inclusion observations201175144080409310.1016/j.gca.2011.04.0282-s2.0-79958823969GordonH. R.McCubbinT. K.Jr.The 2.8-micron bands of CO21966191–413715410.1016/0022-2852(66)90237-22-s2.0-0007852267AzbejT.SeversM. J.RuskB. G.BodnarR. J.In situ quantitative analysis of individual H2O-CO2 fluid inclusions by laser Raman spectroscopy20072373-425526310.1016/j.chemgeo.2006.06.0252-s2.0-33846882858SongY.ChouI. M.HuW.RobertB.LuW.CO2 density-raman shift relation derived from synthetic inclusions in fused silica capillaries and its application20098393293810.1111/j.1755-6724.2009.00090.xPanZ.ChouI.-M.BurrussR. C.Hydrolysis of polycarbonate in sub-critical water in fused silica capillary reactor with in situ Raman spectroscopy2009118110511072-s2.0-6894921778110.1039/b904810nFrezzottiM. L.TecceF.CasagliA.Raman spectroscopy for fluid inclusion analysis20121121202-s2.0-8415517097610.1016/j.gexplo.2011.09.009ShockE. L.HelgesonH. C.Calculation of the thermodynamic and transport properties of aqueous species at high pressures and temperatures: correlation algorithms for ionic species and equation of state predictions to 5 kb and 1000°C19885282009203610.1016/0016-7037(88)90181-02-s2.0-0024190666PokrovskyO. S.GolubevS. V.SchottJ.CastilloA.Calcite, dolomite and magnesite dissolution kinetics in aqueous solutions at acid to circumneutral pH, 25 to 150°C and 1 to 55 atm pCO2: New constraints on CO2 sequestration in sedimentary basins20092651-2203210.1016/j.chemgeo.2009.01.0132-s2.0-68649124849GarrabosY.TufeuR.Le NeindreB.ZalczerG.BeysensD.Rayleigh and Raman scattering near the critical point of carbon dioxide1979728463746512-s2.0-36749111194NicolaJ. H.ScottJ. F.CoutoR. M.CorreaM. M.Raman spectra of dolomite [CaMg(CO3)2]197614104676467810.1103/PhysRevB.14.46762-s2.0-0042257446GunasekaranS.AnbalaganG.PandiS.Raman and infrared spectra of carbonates of calcite structure20063798928992-s2.0-3374899429810.1002/jrs.1518RosascoG. J.BlahaJ. J.Raman microprobe spectra and vibrational mode assignments of talc198034214014410.1366/00037028047306642-s2.0-0018999031TrommsdorffV.EvansB. W.Antigorite-ophicarbonates: phase relations in a portion of the system CaO–MgO–SiO2–H2O–CO21977601395610.1007/BF003728502-s2.0-0002648830TrommsdorffV.ConnollyJ. A. D.Constraints on phase diagram topology for the system CaO–MgO–SiO2–CO2–H2O199010411710.1007/BF003106412-s2.0-0040676787Van GosenB. S.LowersH. A.SutleyS. J.GentC. A.Using the geologic setting of talc deposits as an indicator of amphibole asbestos content20044579209392-s2.0-254251935510.1007/s00254-003-0955-2JohannesW.An experimental investigation of the system MgO-SiO2-H2O-CO2196926791083110410.2475/ajs.267.9.1083SchandlE. S.GortonM. P.Hydrothermal alteration and CO2 metasomatism (natural carbon sequestration) of komatiites in the south-western Abitibi greenstone belt201250112914610.3749/canmin.50.1.1292-s2.0-84863682592EvansB. W.GuggenheimS.BaileyS. W.Talc, phyrophyllite, and related minerals198819225294VeldeB.Experimental pseudomorphism of diopside by talc and serpentine in (Ni, Mg)Cl2 aqueous solutions198852241542410.1016/0016-7037(88)90097-X2-s2.0-38249028191Williams-JonesA. E.NormandC.Clark ValiH.Jr.MartinR. F.DufresneA.Nayebzadeh A.NolanR. P.LangerA. M.RossM.Wicks F. J.Martin F. R.Controls of amphibole formation in chrysotile from the Jeffrey Mine, Asbestos Quebec20015Quebec, CanadaThe Mineralogical Association of Canada, Quebec89104EvansB. W.The serpentinite multisystem revisited: chrysotile is metastable200446647950610.2747/0020-6814.46.6.4792-s2.0-3543075723GunnarssonI.ArnórssonS.Amorphous silica solubility and the thermodynamic properties of H4SiO°4 in the range of 0° to 350°C at Psat200064132295230710.1016/S0016-7037(99)00426-32-s2.0-0343081052BodineM. W.Jr.Trioctahedral clay mineral assemblages in Paleozoic marine evaporite rocks1Proceedings of the Presented in the Sixth International Symposium on Salt1983Toronto, Canada267284SchreyerW.AbrahamK.Three-stage metamorphic history of a whiteschist from Sar e Sang, Afghanistan, as part of a former evaporite deposit19765921111302-s2.0-000141955910.1007/BF00371302AngererT.HagemannS. G.The BIF-hosted high-grade iron ore deposits in the archean koolyanobbing greenstone belt, Western Australia: structural control on synorogenic- and weathering-related magnetite-, hematite-, and goethite-rich iron ore2010105591794510.2113/econgeo.105.5.9172-s2.0-84865183502DuuringP.HagemannS.Leaching of silica bands and concentration of magnetite in Archean BIF by hypogene fluids: Beebyn Fe ore deposit, Yilgarn Craton, Western Australia20134833413702-s2.0-8487436057810.1007/s00126-012-0428-1ShinD.LeeI.Fluid inclusions and their stable isotope geochemistry of the carbonate-hosted talc deposits near the Cretaceous Muamsa Granite, South Korea200640169852-s2.0-3244443282910.2343/geochemj.40.69NovgorodovP. G.Solubility of quartz in an H2O–CO2 mixture at 700 degrees C and pressures of 3 and 5 kbars197514841489GerlachT. M.Chemical characteristics of the volcanic gases from Nyiragongo lava lake and the generation of CH4-rich fluid inclusions in alkaline rocks198082-417718910.1016/0377-0273(80)90103-12-s2.0-0019102188WaltherJ. V.OrvilleP. M.Volatile production and transport in regional metamorphism19827932522572-s2.0-001990972010.1007/BF00371516GiggenbachW. F.BarnesH. L.The origin and evolution of fluids in magmatic-hydrothermal systems19973New York, NY, USAWiley737796LowensternJ. B.Carbon dioxide in magmas and implications for hydrothermal systems20013664905022-s2.0-003481718910.1007/s001260100185KerrichR.FyfeW. S.The gold-carbonate association: source of CO2, and CO2 fixation reactions in Archaean lode deposits1981331–426529410.1016/0009-2541(81)90104-22-s2.0-0019686473NabelekP. I.Calc-silicate reactions and bedding-controlled isotopic exchange in the Notch Peak aureole, Utah: implications for differential fluid fluxes with metamorphic grade200220442944010.1046/j.1525-1314.2002.00379.x2-s2.0-0036095454NabelekP. I.Fluid evolution and kinetics of metamorphic reactions in calc-silicate contact aureoles - From H2O to CO2 and back2007351092793010.1130/G24051A.12-s2.0-35448931441MachelH. G.Bacterial and thermochemical sulfate reduction in diagenetic settings - old and new insights20011401-21431752-s2.0-003505863210.1016/S0037-0738(00)00176-7StalkerL.FarrimondP.LarterS. R.Water as an oxygen source for the production of oxygenated compounds (including CO2 precursors) during kerogen maturation1994223-5477IN410.1016/0146-6380(94)90120-12-s2.0-0028563973ShiptonZ. K.EvansJ. P.KirschnerD.KolesarP. T.WilliamsA. P.HeathJ.Analysis of CO2 leakage through ‘low-permeability’ faults from natural reservoirs in the Colorado Plateau, east-central Utah2004233435810.1144/GSL.SP.2004.233.01.052-s2.0-11144314866ByerleeJ.Friction, overpressure and fault normal compression19901712210921122-s2.0-002564041610.1029/GL017i012p02109MorrowC.RadneyB.ByerleeJ.Chapter 3 frictional strength and the effective pressure law of montmorillonite and lllite clays199251C698810.1016/S0074-6142(08)62815-62-s2.0-77956864118MorrowC. A.MooreD. E.LocknerD. A.The effect of mineral bond strength and adsorbed water on fault gouge frictional strength200027681581810.1029/1999gl0084012-s2.0-0034353332LocknerD. A.MorrowC.MooreD.HickmanS.Low strength of deep San Andreas fault gouge from SAFOD core2011472734182862-s2.0-7995373861010.1038/nature09927MooreD. E.RymerM. J.Talc-bearing serpentinite and the creeping section of the San Andreas fault200744871557957972-s2.0-3454795716310.1038/nature06064ZengerD. H.Discussion: ‘On the formation and occurrence of saddle dolomite’19815141350135210.1306/212F7EB4-2B24-11D7-8648000102C1865D2-s2.0-0019713034KatzD. A.EberliG. P.SwartP. K.SmithL. B.Jr.Tectonic-hydrothermal brecciation associated with calcite precipitation and permeability destruction in Mississippian carbonate reservoirs, Montana and Wyoming20069011180318412-s2.0-3375152954610.1306/03200605072EstebanM.TabernerC.Secondary porosity development during late burial in carbonate reservoirs as a result of mixing and/or cooling of brines200378-793553592-s2.0-304265353510.1016/S0375-6742(03)00111-0MacHelH. G.Investigations of burial diagenesis in carbonate hydrocarbon reservoir rocks20053231031282-s2.0-33846121222SaganJ. A.HartB. S.Three-dimensional seismic-based definition of fault-related porosity development: Trenton-Black River interval, Saybrook, Ohio20069011176317852-s2.0-3375150615610.1306/07190605027XingF.LiS.Genesis and environment characteristics of dolomite-hosted quartz and its significance for hydrocarbon exploration, in Keping Area, Tarim Basin, China20122344764892-s2.0-8486571257010.1007/s12583-012-0269-yYunL.CaoZ.Hydrocarbon enrichment pattern and exploration potential of the Ordovician in Shunnan area, Tarim Basin20143567887972-s2.0-8492411778510.11743/ogg20140606LiY.YeN.YuanX.HuangQ.SuB.ZhouR.Geological and geochemical characteristics of silicified hydrothermal fluids in Well Shunnan 4, Tarim Basin20153669349442-s2.0-8496137157210.11743/ogg20150608QiL.Oil and gas breakthrough in ultra-deep Ordovician carbonate formations in Shuntuoguole uplift, Tarim Basin20162133851(in Chinese with English abstract)QingH. R.An introduction of petrology and diagenesis of ultra-deep water carbonate reservoirs from the Atlantic Ocean, offshore Brazil2017, Oral presentation at Wuxi Institute of Petroleum Geology of SINOPEC, Wuxi, ChinaSimandlG. J.ParadislS.Carbonate-hosted talc199933538KharakaY. K.ColeD. R.HovorkaS. D.GunterW. D.KnaussK. G.FreifeldB. M.Gas-water-rock interactions in Frio Formation following CO2 injection: implications for the storage of greenhouse gases in sedimentary basins200634757758010.1130/G22357.12-s2.0-33745905353DuanZ.LiD.Coupled phase and aqueous species equilibrium of the H2O–CO2–NaCl–CaCO3 system from 0 to 250°C, 1 to 1000 bar with NaCl concentrations up to saturation of halite200872205128514510.1016/j.gca.2008.07.0252-s2.0-52749089678GilesM. R.MarshallJ. D.Constraints on the development of secondary porosity in the subsurface: re-evaluation of processes19863324325510.1016/0264-8172(86)90048-62-s2.0-0001227006PokrovskyO. S.GolubevS. V.SchottJ.Dissolution kinetics of calcite, dolomite and magnesite at 25°C and 0 to 50 atm pCO220052173-423925510.1016/j.chemgeo.2004.12.0122-s2.0-18444407473CaoP.KarpynZ. T.LiL.The role of host rock properties in determining potential CO2 migration pathways201645182610.1016/j.ijggc.2015.12.0022-s2.0-84950249654FishburnM. D.KuespertG. K.ReidS. A.Significant results of deep drilling at Elk Hills, Kern County, California199064Pacific Sections, Society of Economic Paleontologists and Mineralogists and American Association of Petroleum Geologists157167PovodenE.HoracekM.AbartR.Contact metamorphism of siliceous dolomite and impure limestones from the Werfen formation in the eastern Monzoni contact aureole2002761-2991202-s2.0-044226880810.1007/s007100200034YuanS.ChouI.-M.BurrussR. C.WangX.LiJ.Disproportionation and thermochemical sulfate reduction reactions in S–H2O–CH4 and S–D2O–CH4 systems from 200 to 340°C at elevated pressures201311826327510.1016/j.gca.2013.05.0212-s2.0-84879334984WangX.ChouI.-M.HuW.BurrussR. C.In situ observations of liquid-liquid phase separation in aqueous MgSO4 solutions: geological and geochemical implications201310311010.1016/j.gca.2012.10.0442-s2.0-84871110756WangX.WanY.HuW.ChouI.-M.CaoJ.WangX.WangM.LiZ.In situ observations of liquid-liquid phase separation in aqueous ZnSO4 solutions at temperatures up to 400°C: Implications for Zn2+–SO42- association and evolution of submarine hydrothermal fluids201618112614310.1016/j.gca.2016.03.0012-s2.0-84960453243WangX.ChouIM.HuW.WanY.LiZ.Properties of lithium under hydrothermal conditions revealed by in situ Raman spectroscopic characterization of Li2O-SO3-H2O (D2O) systems at temperatures up to 420°C201745110411510.1016/j.chemgeo.2017.01.013ShangL.ChouI.-M.LuW.BurrussR. C.ZhangY.Determination of diffusion coefficients of hydrogen in fused silica between 296 and 523 K by Raman spectroscopy and application of fused silica capillaries in studying redox reactions20097318543554432-s2.0-6814915829910.1016/j.gca.2009.06.001DargentM.DubessyJ.TrucheL.BazarkinaE. F.Nguyen-TrungC.RobertP.Experimental study of uranyl(VI) chloride complex formation in acidic LiCl aqueous solutions under hydrothermal conditions (T = 21°C–350°C, Psat) using Raman spectroscopy201325576577510.1127/0935-1221/2013/0025-23192-s2.0-84892492033WanY.WangX.HuW.ChouI.-M.Raman spectroscopic observations of the ion association between Mg2+ and SO42- in MgSO4-saturated droplets at temperatures of ≤380°C201511934902790362-s2.0-84960348370WanY.WangX.HuW.ChouI. M.ChenY.XuZ.In situ optical and Raman spectroscopic observations of the effects of pressure and fluid composition on liquidliquid phase separation in aqueous cadmium sulfate solutions (=400°C, 50 MPa) with geological and geochemical implications201721113315210.1016/j.gca.2017.05.020MarshallW. L.Amorphous silica solubilities—I. Behavior in aqueous sodium nitrate solutions; 25–300°C, 0–6 molal198044790791310.1016/0016-7037(80)90280-X2-s2.0-0019213218ChenC.-T. A.MarshallW. L.Amorphous silica solubilities IV. Behavior in pure water and aqueous sodium chloride, sodium sulfate, magnesium chloride, and magnesium sulfate solutions up to 350°C198246227928710.1016/0016-7037(82)90255-12-s2.0-0019923846FlemingB. A.CrerarD. A.Silicic acid ionization and calculation of silica solubility at elevated temperature and pH application to geothermal fluid processing and reinjection198211115292-s2.0-002042966210.1016/0375-6505(82)90004-9