International Journal of Aerospace Engineering
Volume 2018 (2018), Article ID 5610915, 23 pages
https://doi.org/10.1155/2018/5610915

Research Article

Nonlinear Dynamics of the High-Speed Rotating Plate

Minghui Yao, Li Ma, and Wei Zhang

Beijing Key Laboratory of Nonlinear Vibrations and Strength of Mechanical Structures, College of Mechanical Engineering, Beijing University of Technology, Beijing 100124, China

Correspondence should be addressed to Minghui Yao; merry_mingming@163.com

Received 21 July 2017; Revised 6 November 2017; Accepted 23 November 2017; Published 27 February 2018

Academic Editor: Christopher J. Damaren

Copyright © 2018 Minghui Yao et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

High speed rotating blades are crucial components of modern large aircraft engines. The rotating blades under working condition frequently suffer from the aerodynamic, elastic and inertia loads, which may lead to large amplitude nonlinear oscillations. This paper investigates nonlinear dynamic responses of the blade with varying rotating speed in supersonic airflow. The blade is simplified as a pre-twist and presetting cantilever composite plate. Warping effect of the rectangular cross-section of the plate is considered. Based on the first-order shear deformation theory and von-Karman nonlinear geometric relationship, nonlinear partial differential dynamic equations of motion for the plate are derived by using Hamilton’s principle. Galerkin approach is applied to discretize the partial differential governing equations of motion to ordinary differential equations. Asymptotic perturbation method is exploited to derive four-degree-of-freedom averaged equation for the case of 1 : 3 internal resonance-1/2 sub-harmonic resonance. Based on the averaged equation, numerical simulation is used to analyze the influence of the perturbation rotating speed on nonlinear dynamic responses of the blade. Bifurcation diagram, phase portraits, waveforms and power spectrum prove that periodic motion and chaotic motion exist in nonlinear vibration of the rotating cantilever composite plate.

1. Introduction

High-speed rotating blades are essential components of modern large aircraft engines. Blades are designed with large aspect ratios and thin-wall structure in order to raise operational efficiency. In the actual working condition, the rotating blades are frequently subjected to the aerodynamic, elastic, and inertia loads. Various types of excitation lead to large amplitude nonlinear parametric vibrations of the blades, which can result in the resonance phenomena and undesirable disasters, especially when the rotating blades operate with high speed and huge centrifugal force. According to the investigation, the vibration failure of the aircraft engine is more than 60% of the total failure, while the vibration failure of the blade accounts for more than 70% of the total vibration failure. Resonance and flutter produced by the forced vibration and self-excited vibration are the main reason leading to the blade failure. So, it is very important that a reasonable model is established to accurately predict nonlinear vibration characteristics and other complex dynamics of the blade.

In recent years, considerable attention has been given to the studies on the vibration characteristics of rotating blades. Lin et al. [1] deduced governing differential equations and general elastic boundary conditions of a nonuniform pretwist Timoshenko beam by using Hamilton’s principle. Yao et al. [2] investigated the nonlinear dynamic responses of the thin-walled rotating cantilever beam. Sarkar and Ganguli [3] assumed the modal function as polynomials satisfying all four boundary conditions and discussed free vibration of the nonhomogeneous Timoshenko beam. Georgiades et al. [4] derived equations of motion of a rotating composite Timoshenko beam by utilizing Hamilton’s principle. Xie et al. [5, 6] numerically investigated the effect of symmetric and asymmetric shroud gaps, rotational speeds, and the aerodynamic force amplitude on dynamic characteristics of the rotating Euler-Bernoulli beam with a mass point at the free end. Huang and Kuang [7] investigated the effect of a near root local blade crack on the stability of a bladed disk, in which an individual blade is modeled simply as a cantilever Euler-Bernoulli beam.

Currently, plenty of theoretical analyses are focused on the beam model of the blade, such as the simple Euler-Bernoulli beam and the pretwist Timoshenko beam. But, theoretical studies on the plate model of the blade are still few. Young and Liou [8] established equations of a rotating cantilever plate with a time-varying speed and numerically investigated the effect of the Coriolis force on boundaries of the unstable regions. Yoo and Kim [9] derived linear equations of motion and analyzed free vibration of rotating cantilever plates. Sinha and Turner [10] derived governing partial differential equations of motion for a rotating pretwist plate to investigate the static and dynamic frequencies of the blade. Li and Zhang [11] presented a dynamic model of a functionally graded rectangular plate undergoing large overall motions. Kouchakzadeh et al. [12] analyzed the nonlinear aeroelasticity of a laminated composite plate in supersonic airflow by using the classical plate theory. Malgaca et al. [13] tried to control the vibration of the rotating blade at different speeds by utilizing root-embedded piezoelectric materials. Kam et al. [14] proposed a procedure to analyze the structural failure of a composite wind blade subjected to quasi-static loads. Tang and Chen [15] presented the solvability conditions of nonlinear partial differential equations for in-plane moving plates of two cases, in which the one case is without internal resonance and another case is under internal resonances, respectively. Sun et al. [16] used a quadratic layerwise theory and a new dynamic model to study dynamic behaviors for a multilayer pretwist rotating blade. Wang et al. [17] established a time-dependent nonlinear model of a flexible blade-rotor-bearing system by using the Lagrange method. Shariyat et al. [18] performed the nonlinear dynamic analysis of rectangular composite plates. Zhang and Li [19] adopted the Lagrangian method to acquire dynamic equations of motion for the pretwist and predeformed rotating cantilever plate subjected to the harmonic aerodynamic force. Mendonça et al. [20] considered internal damping in the shaft to study dynamic behaviors of the rotors mounted on composite shafts. Banichuk et al. [21, 22] investigated the stability and bifurcation of the rotating blade under different conditions.

Based on the shallow shell theory and the Ritz method, Leissa et al. [23] explored frequencies and mode shapes of turbomachinery blades with the coupling of bending and twist. Kee and Kim [24] assumed blades as the moderately thick open cylindrical shell models. Sun et al. [25] applied the general shell theory to investigate the influence of parameters on natural frequency and damping characteristics of the shell model blade. Sinha and Zylka [26] simplified the rotating pretwisted turbomachinery cantilevered airfoil as an anisotropic shell and derived the free vibration equations of motion for the transverse deflection of the shell including the warping effect. Volker and Joachim [27] analyzed the aeroelastic phenomena of twenty compressor blades simplified as the spring-damper models mounted on the hub. Ekici et al. [28] proposed a nonlinear harmonic balance method to compute the unsteady self-excited aerodynamic of asymmetry turbomachinery blades. Farhadi and Hosseini-Hashemi [29] studied aeroelastic behaviors of a rotating thick plate in the supersonic airflow. Lachenal et al. [30] presented the design, analysis, and realization of a zero stiffness twist morphing wind turbine blade subjected to the gust loads.

Dynamic modeling of the rotating blade requires an accurate expression of the aerodynamic force. But, the physical mechanism of aerodynamic interaction has been mainly investigated by experimental methods. Models have been proposed to deal with aerodynamic interaction problems, which is done with by the piston theory widely. Ashley and Zartarian [31] firstly proposed the quasi-steady piston theory to deal with aerodynamic interaction problems. Navazi and Haddadpour [32] studied the thermal stability of the functionally graded plate subjected to the aerodynamic load obtained from the first-order piston theory. According to large deformation geometric relationship, the piston theory and the quasi-static thermal stress theory, Yuan and Qiu [33] established the aerodynamic model of a composite stiffened panel and used Hamilton’s principle to derive the equations of motion for the system. Yang et al. [34] applied a modified local piston theory to analyze aeroelastic behaviors of curved panels.

Although extensive studies have been carried out on rotating cantilever beams, studies on nonlinear dynamic responses of the pretwist, presetting rotating cantilever plates are still few. In this paper, nonlinear dynamic behaviors of the blade with varying rotating speeds under the supersonic airflow are investigated. Considering the shear deformation and the warping effect, equations of motion for the cantilever plate are derived by using Hamilton’s principle. The Galerkin approach is applied to discretize the partial differential governing equations of motion to ordinary differential equations. The asymptotic perturbation method is exploited to obtain averaged equations of the system in the case of 1 : 3 internal resonance-1/2 subharmonic resonance. Based on the averaged equations, numerical simulation is applied to investigate the bifurcation and chaotic dynamics of the rotating cantilever composite plate. In order to analyze the internal resonance, we choose the perturbation rotating speed as the controlling parameter to investigate nonlinear behaviors of the pretwist and presetting rotating cantilever plate. From the results of the numerical simulation, it is found that the system performs periodic and chaotic motions under specific conditions. It is observed that the perturbation rotating speed has a significant influence on the nonlinear dynamic behaviors of the rotating plate. Since we can control the responses of the system from the chaotic motions to the periodic motions by changing the perturbation rotating speed, we can control the large amplitude nonlinear vibrations of the blade.

2. Equations of Motion for the Rotating Cantilevered Blade

The schematic diagram of the rotating cantilever blade is shown in Figure 1. The blade is simplified as a pretwist and presetting rotating cantilever plate in the following dynamical analysis. Rotating speed of the blade is , where is the steady-state rotating speed and is the periodic perturbation. The shape of the blade is a rectangular plate, which is characterized by the span length , the chord length , and the thickness . The cross-section of the cantilever plate is shown in Figure 2. The plate is clamped to a rigid hub of radius . There are a presetting angle in the fixed end and a pretwist angle at the free end. is the inertial frame and the origin of it is in the center of the hub. At the edge of the hub, there is the rotating coordinate system . We define that the spanwise direction is , the chordwise direction is , and the thickness direction is . Another local triad system attached to the free end of the plate is introduced on the plate, which is called the sectional coordinate system.

Figure 1: The model of the pretwist rotating cantilever rectangular plate.

Figure 2: The section of the rotating cantilever plate.

The twist rate of the blade is expressed as

and the twist angle of the blade is written as

Based on the Kirchhoff hypothesis, the first-order shear deformation theory including the warping effect is considered to establish the displacement field. Displacements of any point along , , and directions can be expressed by the displacement of the neutral plane of the plate as follows [35]:

where

Nonlinear strains of the von Karman plate theory are given as

where is the membrane strain and is the flexural strain.

For the advanced fiber-reinforced composite material blade, the constitutive relation of the composite plate is expressed as follows:

where

where is the longitudinal modulus of the fiber, is the transverse modulus, and are the major Poisson’s ratio, respectively, and , , and are the shear modulus, respectively.

In-plane force resultants , , and ; the moment resultants , , and ; and the transverse forces and are written in matrices as follows:

where represents the shear coefficient, is called the extensional stiffness, is the bending stiffness, and is the bending-extensional coupling stiffness, which are defined as

, , and are mass moments of inertia, which are defined as

The rotating plate mounted in the hub is rotating with the variable speed. The displacement of a random point without deformation on the plate is expressed as

and the deformation displacement of a random point on the rotating plate is written as

where , , and denote displacement components along , , and directions, respectively.

When the blade rotates with a constant angular velocity , the transient angle can be written as

The instantaneous direction of the local unit vector for any typical point on the blade with respect to the stationary global Cartesian unit vector is given by

The speed and the acceleration of any random point on the plate are described as follows:

where

The variation of the kinetic energy is given by

A large centrifugal force will be generated when the compressor blade of the aircraft engine operates with the high rotating speed. Components of centrifugal forces along the spanwise and chordwise directions are described by and , which can be expressed as

The variation of the potential energy consists the variation of the strain energy and the variation of the centrifugal potential energy , namely, , where

Aerodynamic forces of the blade derived by the first-order piston theory are written as

where is the air density, is the speed of sound, is the speed of the airflow, and , .

The variation of the virtual work of aerodynamic forces is expressed as follows:

Nonlinear dynamic equations of motion for the rotating blade are established by using Hamilton’s principle.

Substituting (11), (13a), (13b), and (15) into (16), the nonlinear partial governing equations for nonlinear vibration of the rotating blade expressed in terms of displacement variables can be derived as follows:

The boundary conditions are given as follows:

The dimensionless variables and parameters are introduced as follows:

Substituting (23) into (17), (18), (19), (20), and (21), we obtain the dimensionless governing equations of motion for the blade.

Based on the practical working condition of the blade, and theoretical and numerical studies given by Dowell et al. [36, 37], it is known that vibrations of the first two order modes for the blade play an important role during vibration. The Galerkin approach is applied to obtain ordinary differential equations of motion in the dimensionless form. The Galerkin approach is derived by the Taylor expansion method, which is a mathematically convergent method. The first two order mode functions can produce convergent results. Mode functions of the plate , , , , and are given as follows based on a combination method of beam functions

where

where are coefficients related to frequencies, , and are coefficients of beam functions as follows:

Substitute (24a), (24b), (24c), (24d), and (24e) into the dimensionless governing equations of motion and express , , , and with . Ordinary differential equations of transverse vibration for the first mode and the second mode of the rotating blade in the dimensionless form are derived through the Galerkin method as follows:

where expressions of coefficients , , and are described in the appendix.

3. Perturbation Analysis

There are both square nonlinear terms and cubic terms in (25a) and (25b), so the asymptotic perturbation method is exploited to derive average equations. The small parameter is introduced. The scale transformation is performed as follows:

The case of 1 : 3 internal resonance-1/2 sub-harmonic resonance for the rotating plate is considered. Relationship between and is expressed as

where and are two detuning parameters.

Substituting (26) and (27) into (25a) and (25b), we obtain the following equation

The time scale transformation is introduced as

where is the positive rational number, which will be determined in the following deduction.

Functions and are the solutions of (28a) and (28b), which can be expressed as a power series of small parameter .

In (30a) and (30b), if , then , otherwise . In the following derivation, we will fix .

The real part of and are written as follows:

where the item with the asterisk on the right-hand side is the complex conjugate of the item on the left-hand side.

Solutions of (28a) and (28b) can be rewritten more explicitly as follows:

where denotes terms of the complex conjugate of functions on the right-hand side.

Solutions of (28a) and (28b) can be expressed as harmonic functions, whose coefficients are related to small parameter , as shown in (32a) and (32b). Functions and are given by

We suppose when , the limits of and exist. Meanwhile, we define and for and and for . When , we obtain the derivative results as follows:

In order to solve the coefficients of and , substituting (30a) and (30b) into (28a) and (28b), we obtain equations for each harmonic with order and a fixed order of approximation on the perturbation parameter .

When , we get the following expressions:

The solvability of (35a) and (35b) requires . Thus, we obtain the following expressions:

When , considering derivative forms of (34a) and (34b) yields

Then, the following equations are obtained

When , for the balance of the nonlinear and linear terms, we must make . Equations can be derived as follows:

Substitute (36a) and (36b) and (38a) and (38b) into (39a) and (39b), differential equations about and are derived as

Make and as follows:

Substitute (41a) and (41b) into (40a) and (40b), averaged equation in the Cartesian form is obtained as

where expressions of coefficients , , , and are described in the appendix.

4. Numerical Simulation of Nonlinear Vibrations

4.1. Comparison about Frequencies

In this section, based on the kinetic energy and the potential energy of the blade deduced in the previous section, the Chebyshev polynomial and Ritz method are used to calculate the frequency of the model, which are compared with the frequency obtained by finite element method.

To validate the model proposed, we compare frequencies theoretically calculated with frequencies obtained by the finite element method. Geometrical parameters and physical properties of the compressor blade are selected as the spanwise length , the chordwise length , the mounting angle , the hub radius , the density , the Poisson’s ratio , the elastic modulus , the inlet velocity , the inlet mass flow , the real flow velocity . Table 1 shows frequencies of different orders obtained by two methods above. When the rotating speed increases from 0 rpm to 15000 rpm, frequencies calculated by those two methods are in good agreement. So, the model is reasonable.

Table 1: Frequency comparison.

1st
2nd
3rd

FEM
C-R
FEM
C-R
FEM
C-R

0 rpm
1130.4
1076.6
4038.4
3117.2
6288.6
6253.9

30000 rpm
1133.4
1080.6
4039.1
3118.7
6291.8
6257.7

6000 rpm
1142.2
1092.8
4041
3123.2
6301.2
6269.2

9000 rpm
1156.6
1112.7
4044.2
3130.6
6316.9
6288.3

12000 rpm
1176.6
1140
4048.7
3141
6338.8
6314.9

15000 rpm
1201.7
1156.2
4054.5
3169.9
6366.9
6341

4.2. Numerical Simulation

Based on (42a), (42b), (42c), and (42d), we consider the influences of dimensionless parameters on nonlinear vibration behaviors of the rotating cantilever blade. Numerical simulation is utilized to investigate nonlinear dynamics of the rotating cantilever composite plate subjected to the aerodynamic force and the centrifugal force. Nonlinear oscillation of the system is investigated by choosing the perturbation rotating speed as the controlling parameter. When other parameters and the initial condition do not vary, we only change to detect the influence of the periodic perturbation rotating speed on vibration of the rotating cantilever composite blade. The Runge-Kutta algorithm and the Poincare map theory are used to construct numerical results of the bifurcation diagram, which describes the vibration law of the displacement , when changes in a certain region.

When the parameter is chosen in the interval , and other parameters and the initial condition are, respectively, chosen as , , , , , , , , , , , , , , , , , , , , , and , we obtain Figure 3. Figure 3 describes the bifurcation diagram on the plane when varies in the interval . It can be observed that periodic motion and chaotic motion appear in the vibration of the blade. With the increase of the perturbation rotating speed , Figure 3 presents the following law: periodic motion → chaotic motion → periodic motion → chaotic motion → periodic motion.

Figure 3: Bifurcation diagram on the plane when the perturbation rotating speed varies in the interval . The initial condition is , , , and .

The chaotic and periodic responses can be identified by several conventional criteria. Thus, based on the bifurcation diagram, the waveform, phase portraits, and the power spectrum are utilized to further verify the existence of the chaotic and periodic motion of the blade. Figures 4 and 5 illustrate that the system occurs multiperiodic motion when the perturbation rotating speed is chosen as and , respectively. Figures 4(a) and 4(c) represent the phase portraits on the planes and , respectively. Figures 4(b) and 4(d) give the waveform on the plane and , respectively. Figure 4(e) represents the three-dimensional phase portrait in the space . Figure 4(f) describes the power spectrum on the plane . It can be shown from Figure 4 that the amplitude of the first-order mode is larger than that of the second-order mode. Figure 6 indicates that the chaotic motion of the system appears when . Figures 7 and 8 illustrate that multiperiodic motion of the rotating composite plate occur, when the perturbation rotating speed continues to increase and is selected as and , respectively. Figure 9 shows that the chaotic motion of the rotating cantilever composite plate exists when . Figure 10 illustrates that the system exhibits multiperiodic motion when increases to .

(a)

(b)

(c)

(d)

(e)

(f)

Figure 4: The multiperiodic motion of the blade with varying rotating speeds when . (a) The phase portrait on the plane ; (b) the waveform on the plane ; (c) the phase portrait on the plane ; (d) the waveform on the plane ; (e) the phase portrait in the three-dimensional space ; and (f) the power spectrum on the plane .

(a)

(b)

(c)

(d)

(e)

(f)

Figure 5: The multiperiodic motion of the blade with varying rotating speeds when . (a) The phase portrait on the plane ; (b) the waveform on the plane ; (c) the phase portrait on the plane ; (d) the waveform on the plane ; (e) the phase portrait in the three-dimensional space ; and (f) the power spectrum on the plane .

(a)

(b)

(c)

(d)

(e)

(f)

Figure 6: The chaotic motion of the blade with varying rotating speeds when . (a) The phase portrait on the plane ; (b) the waveform on the plane ; (c) the phase portrait on the plane ; (d) the waveform on the plane ; (e) the phase portrait in the three-dimensional space ; and (f) the power spectrum on the plane .

(a)

(b)

(c)

(d)

(e)

(f)

Figure 7: The multiperiodic motion of the blade with varying rotating speeds when . (a) The phase portrait on the plane ; (b) the waveform on the plane ; (c) the phase portrait on the plane ; (d) the waveform on the plane ; (e) the phase portrait in the three-dimensional space ; (f) the power spectrum on the plane .

(a)

(b)

(c)

(d)

(e)

(f)

Figure 8: The multiperiodic motion of the blade with varying rotating speeds when . (a) The phase portrait on the plane ; (b) the waveform on the plane ; (c) the phase portrait on the plane ; (d) the waveform on the plane ; (e) the phase portrait in the three-dimensional space ; and (f) the power spectrum on the plane .

(a)

(b)

(c)

(d)

(e)

(f)

Figure 9: The chaotic motion of the blade with varying rotating speeds when . (a) the phase portrait on the plane ; (b) the waveform on the plane ; (c) the phase portrait on the plane ; (d) the waveform on the plane ; (e) the phase portrait in the three-dimensional space ; and (f) the power spectrum on the plane .

(a)

(b)

(c)

(d)

(e)

(f)

Figure 10: The multiperiodic motion of the blade with varying rotating speeds when . (a) The phase portrait on the plane ; (b) the waveform on the plane ; (c) the phase portrait on the plane ; (d) the waveform on the plane ; (e) the phase portrait in the three-dimensional space ; and (f) the power spectrum on the plane .

Numerical simulation indicates that the system performs complex dynamic behaviors, such as multiperiodic motion and chaotic motion, when changes in a certain region. The perturbation rotating speed affects the dynamic behaviors of the system significantly.

5. Conclusions

In this paper, nonlinear vibration behaviors of the high rotating cantilever plate subjected to the centrifugal force and the aerodynamic force are investigated. Nonlinear partial differential governing equations of the rotating blade are derived by utilizing Hamilton’s principle. The Galerkin method is applied to discretize the nonlinear partial differential governing equations. The method of asymptotic perturbation is adopted to obtain the four-dimension nonlinear averaged equation of motion for the blade in the case of 1 : 3 internal resonance-1/2 subharmonic resonance. Numerical simulations are used to study nonlinear dynamic responses of the blade.

The bifurcation diagram, phase portrait, and power spectrum are conducted to demonstrate that periodic motions and chaotic motions occur in nonlinear vibrations of the rotating blade under certain conditions. In this paper, the perturbation rotating speed is selected as the controlling parameter. Numerical simulation shows that nonlinear dynamic motions of the blade are sensitive to the perturbation rotating speed. The periodic motion and chaotic motion of the blade appear alternately. Periodic motions and chaotic motions exist in the averaged equations. It is well known that periodic motions and chaotic motions in the averaged equations can lead to amplitude-modulated periodic and chaotic vibrations in the original system under certain conditions. Therefore, amplitude-modulated periodic and chaotic motions occur in the rotating blade. Occurrence of the chaotic motion means that the rotating cantilever blade may perform large amplitude nonlinear vibration, which leads to the damage of the system. We can control the responses of the system from the chaotic motions to the periodic motions by changing the perturbation rotating speed. Finally, the large-amplitude vibrations of the blade can be controlled. Thus, study on nonlinear behavior of the blade is of great significance.

Analytical results of this paper can be widely used in the practical aircraft engines. Large amplitude nonlinear vibration produced by the forced vibration and self-excited vibration occasionally leads to the undesirable disaster of the blade. Since chaotic motion is the large amplitude nonlinear vibration, we can adjust the perturbation rotating speed to control the responses of the system in order to avoid the appearance of the chaotic motion. Moreover, the possibility of aircraft engine failure caused by nonlinear vibration is reduced to ensure the safety of the aeroplane.

Appendix

Coefficients in Equations

Coefficients represented in (25a) and (25b) are given as follows:

where

Coefficients represented in (42a), (42b), (42c), and (42d) are as follows:

Nomenclature

: | Rotating speed
: | Steady-state rotating speed
: | Periodic perturbation amplitude of the rotating speed
: | Angular velocity of the blade
: | Plate spanwise length
: | Plate chordwise length
: | Plate thickness
: | Radius of the rigid hub
: | Presetting angle
: | Pre-twist angle
: | Inertial frame
: | Rotating coordinate system
: | Local triad system
: | Twist rate
: | Twist angle
, , : | Components of displacement of a point at the neutral plane
, , : | Components of displacement of a random point
, : | Angular displacement
, , , , : | Components of strains of a point
: | Membrane strain
: | Flexural strain
, : | Coefficients of beam functions
, , , , : | Components of stresses of a point
: | Plane stress-reduced stiffnesses
, : | Detuning parameters
, : | Longitudinal modulus and transverse modulus of the fiber
, : | Poisson’s ratio
, , : | Shear modulus
, , : | In-plane force resultants
, , : | Moment resultants
, : | Transverse forces
: | Shear coefficient
: | Extensional stiffness
: | Bending stiffness
: | Bending-extensional coupling stiffness
, , : | Mass moments of inertia
: | Displacement of a point without deformation
: | Rotating angle of the blade
, : | Speed and acceleration
: | Kinetic energy
, : | Components of the centrifugal force
: | Density of the blade
: | Potential energy
: | Strain energy
: | Centrifugal potential energy
: | Air density
: | Speed of sound
: | Speed of the airflow
: | Virtual work of aerodynamic forces
: | The variation
: | Small parameter
, : | The first two mode frequencies
: | Time scale transformation
: | Positive rational number
: | Inlet velocity
: | Inlet mass flow
: | Real flow velocity.

Conflicts of Interest

The authors declare that there are no conflicts of interest regarding the publication of this paper.

Acknowledgments

The authors gratefully acknowledge the support of the National Natural Science Foundation of China (NNSFC) through Grant no. 11372015.

References

S. M. Lin, W. R. Wang, and S. Y. Lee, “The dynamic analysis of nonuniformly pretwisted Timoshenko beams with elastic boundary conditions,” International Journal of Mechanical Sciences, vol. 43, no. 10, pp. 2385–2405, 2001.

M. H. Yao, Y. P. Chen, and W. Zhang, “Nonlinear vibrations of blade with varying rotating speed,” Nonlinear Dynamics, vol. 68, no. 4, pp. 487–504, 2012.

K. Sarkar and R. Ganguli, “Analytical test functions for free vibration analysis of rotating non-homogeneous Timoshenko beams,” Meccanica, vol. 49, no. 6, pp. 1469–1477, 2014.

F. Georgiades, J. Latalski, and J. Warminski, “Equations of motion of rotating composite beam with a nonconstant rotation speed and an arbitrary preset angle,” Meccanica, vol. 49, no. 8, pp. 1833–1858, 2014.

H. Ma, F. Xie, H. Nai, and B. Wen, “Vibration characteristics analysis of rotating shrouded blades with impacts,” Journal of Sound and Vibration, vol. 378, pp. 92–108, 2016.

F. Xie, H. Ma, C. Cui, and B. Wen, “Vibration response comparison of twisted shrouded blades using different impact models,” Journal of Sound and Vibration, vol. 397, pp. 171–191, 2017.

B. W. Huang and J. H. Kuang, “Variation in the stability of a rotating blade disk with a local crack defect,” Journal of Sound and Vibration, vol. 294, no. 3, pp. 486–502, 2006.

T. H. Young and G. T. Liou, “Coriolis effect on the vibration of a cantilever plate with time-varying rotating speed,” Journal of Vibration and Acoustics, vol. 114, no. 2, pp. 232–241, 1992.

H. Yoo and S. K. Kim, “Free vibration analysis of rotating cantilever plates,” AIAA Journal, vol. 40, no. 11, pp. 2188–2196, 2002.

S. K. Sinha and K. E. Turner, “Natural frequencies of a pre-twisted blade in a centrifugal force field,” Journal of Sound and Vibration, vol. 330, no. 11, pp. 2655–2681, 2011.

L. Li and D. G. Zhang, “Free vibration analysis of rotating functionally graded rectangular plates,” Composite Structures, vol. 136, pp. 493–504, 2016.

M. A. Kouchakzadeh, M. Rasekh, and H. Haddadpour, “Panel flutter analysis of general laminated composite plates,” Composite Structures, vol. 92, no. 12, pp. 2906–2915, 2010.

L. Malgaca, H. Al-Qahtani, and M. Sunar, “Vibration control of rotating blades using root-embedded piezoelectric materials,” Arabian Journal for Science and Engineering, vol. 40, no. 5, pp. 1487–1495, 2015.

T. Y. Kam, H. M. Su, and C. Y. Huang, “Quasi-static buckling and first-ply failure loads of shear web reinforced glass-fabric composite wind blades,” Composite Structures, vol. 160, pp. 1225–1235, 2017.

Y. Q. Tang and L. Q. Chen, “Nonlinear free transverse vibrations of in-plane moving plates: without and with internal resonances,” Journal of Sound and Vibration, vol. 330, no. 1, pp. 110–126, 2011.

J. Sun, I. L. Arteaga, and L. Kari, “Dynamic modeling of a multilayer rotating blade via quadratic layerwise theory,” Composite Structures, vol. 99, no. 5, pp. 276–287, 2013.

L. Wang, D. Q. Cao, and W. Huang, “Nonlinear coupled dynamics of flexible blade–rotor–bearing systems,” Tribology International, vol. 43, no. 4, pp. 759–778, 2010.

M. Shariyat, M. Moradi, and S. Samaee, “Enhanced model for nonlinear dynamic analysis of rectangular composite plates with embedded SMA wires, considering the instantaneous local phase changes,” Composite Structures, vol. 109, pp. 106–118, 2014.

B. Zhang and Y. Li, “Nonlinear vibration of rotating pre-deformed blade with thermal gradient,” Nonlinear Dynamics, vol. 86, no. 1, pp. 459–478, 2016.

W. R. D. P. Mendonça, E. C. D. Medeiros, and A. L. R. Pereira, “The dynamic analysis of rotors mounted on composite shafts with internal damping,” Composite Structures, vol. 167, pp. 50–62, 2017.

X. Zhang, F. Chen, B. Zhang, and T. Jing, “Local bifurcation analysis of a rotating blade,” Applied Mathematical Modelling, vol. 40, no. 5-6, pp. 4023–4031, 2016.

N. Banichuk, A. Barsuk, J. Jeronen, P. Neittaanmaki, and T. Tuovinen, “On bifurcation analysis of implicitly given functionals in the theory of elastic stability,” Mathematical Modeling and Optimization of Complex Structures, vol. 40, pp. 175–188, 2015.

A. W. Leissa, J. K. Lee, and A. J. Wang, “Rotating blade vibration analysis using shells,” Journal of Engineering for Power, vol. 104, no. 2, pp. 296–302, 1982.

Y. J. Kee and J. H. Kim, “Vibration characteristics of initially twisted rotating shell type composite blades,” Composite Structures, vol. 64, no. 2, pp. 151–159, 2004.

J. Sun, I. L. Arteaga, and L. Kari, “General shell model for a rotating pretwisted blade,” Journal of Sound and Vibration, vol. 332, no. 22, pp. 5804–5820, 2013.

S. K. Sinha and R. P. Zylka, “Vibration analysis of composite airfoil blade using orthotropic thin shell bending theory,” International Journal of Mechanical Sciences, vol. 121, pp. 90–105, 2017.

C. Volker and B. Joachim, “Numerical investigation of nonlinear fluid-structure interaction in vibrating compressor blades,” Journal of Turbomachinery, vol. 123, no. 2, pp. 402–408, 2000.

K. Ekici, R. E. Kielb, and K. C. Hall, “Aerodynamic asymmetry analysis of unsteady flows in turbomachinery,” Journal of Turbomachinery, vol. 132, no. 1, article 011006, 2009.

S. Farhadi and S. H. Hosseini-Hashemi, “Aeroelastic behavior of cantilevered rotating rectangular plates,” International Journal of Mechanical Sciences, vol. 53, no. 4, pp. 316–328, 2011.

X. Lachenal, S. Daynes, and P. M. Weaver, “A zero torsional stiffness twist morphing blade as a wind turbine load alleviation device,” Smart Materials & Structures, vol. 22, no. 6, article 065016, 2013.

A. Holt and Z. Garabed, “Piston theory-a new aerodynamic tool for the aeroelastician,” Journal of the Aeronautical Sciences, vol. 23, no. 12, pp. 1109–1118, 1956.

H. M. Navazi and H. Haddadpour, “Aero-thermoelastic stability of functionally graded plates,” Composite Structures, vol. 80, no. 4, pp. 580–587, 2007.

K. H. Yuan and Z. P. Qiu, “Nonlinear flutter analysis of stiffened composite panels in supersonic flow,” Science China Physics, Mechanics and Astronomy, vol. 53, no. 2, pp. 336–344, 2010.

Z. Yang, J. Zhou, and Y. Gu, “Integrated analysis on static/dynamic aeroelasticity of curved panels based on a modified local piston theory,” Journal of Sound and Vibration, vol. 333, no. 22, pp. 5885–5897, 2014.

J. N. Reddy, Mechanics of Laminated Composite Plates and Shells Theory and Analysis, CRC Press, Boca Raton, FL, USA, 2000.

E. Dowell and W. Ye, “Limit cycle oscillation of a fluttering cantilever plate,” AIAA Journal, vol. 29, no. 11, pp. 1929–1936, 1991.

D. Tang, E. H. Dowell, and K. C. Hall, “Limit cycle oscillations of a cantilevered wing in low subsonic flow,” AIAA Journal, vol. 37, no. 3, pp. 364–371, 1999.