International Journal of Antennas and Propagation

Volume 2013 (2013), Article ID 941924, 9 pages

http://dx.doi.org/10.1155/2013/941924

Review Article

Dual-Band Integrated Antennas for DVB-T Receivers

Andrea D'alessandro,¹ Roberto Caso,¹ Marcos R. Pino,² and Paolo Nepa¹

¹Department of Information Engineering, University of Pisa, I-56122 Pisa, Italy

²Department of Electrical Engineering, University of Oviedo, 3203 Gijón, Spain

Received 6 December 2012; Accepted 30 March 2013

Academic Editor: Renato Cicchetti

Copyright © 2013 Andrea D'alessandro et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

An overview on compact Planar Inverted-F Antennas (PIFAs) that are suitable for monitor-equipped devices is presented. In particular, high efficiency PIFAs (without any dielectric layer) with a percentage bandwidth (%BW) greater than 59% (470–862 MHz DVB-T band) are considered. In this context, two PIFA configurations are reviewed, where a dual-band feature has been obtained, in the 3300–3800 MHz (14% percentage bandwidth) WiMAX and 2400–2484 MHz (2.7% percentage bandwidth) WLAN IEEE 802.11b,g frequency bands, respectively, to also guarantee web access to on-demand services. The two PIFAs fill an overall volume of  mm³ and  mm³, respectively. They are composed of a series of branches, properly dimensioned and separated to generate the required resonances. Finally, to show the extreme flexibility of the previous two configurations, a novel dual-band L-shape PIFA has been designed. A reflection coefficient less than −6 dB and −10 dB and an antenna gain of around 2 dBi and 6.3 dBi have been obtained in the 470–862 MHz DVB-T band and the 2400–2484 MHz WLAN band, respectively. The L-shape PIFA prototype can be obtained by properly cutting and folding a single metal sheet, thus resulting in a relatively low-cost and mechanically robust antenna configuration.

1. Introduction

Many countries already switched their terrestrial television broadcasting from analog to Digital Video Broadcasting-Terrestrial (DVB-T) [1]; besides, the demand for digital television reception is increasing also for mobile terminals, such as smart phones and notebooks, which include web access through Wireless Local Area Networks (WLANs) as well. Due to the severe space limitations of typical monitor-equipped devices, dual-band compact integrated antennas for DVB-T and WLAN applications are more attractive than a couple of distinct single-band antennas. Several wideband antennas suitable for DVB-T applications (percentage bandwidth greater than 59%) have been recently presented [2–16]. Among them, PIFAs are those more suitable for integration into multifunctions devices with a high density of electronic circuits; indeed, their own ground plane acts as an electromagnetic shield and the 3D structure helps in enlarging impedance bandwidth. Also, multiple frequency bands can be achieved by adding more resonating paths [17]. A linear-shape PIFA working in the DVB-T and WIMAX frequency bands has been presented in [18]. Moreover, an alternative layout for a dual-band linear-shape PIFA has been more recently proposed in [19], for an antenna operating in the DVB-T and WLAN frequency bands. Since the PIFAs in [18, 19] cannot be made shorter than 20 cm, while still getting an acceptable input impedance matching at the DVB-T frequency band, some other layout modifications are needed for integration into those devices with a length of the monitor sides not greater than 13–15 cm, or when part of the space along the monitor border is occupied by a webcam or a microphone. In such cases, a possible modification of the antenna layout with respect to that in [18, 19] is based on conforming the antenna to the shape of one of the device corners (a few preliminary simulation results were presented in [20]). In this paper, both numerical simulations and experimental results for an L-shape PIFA layout derived from that in [19] are presented, to show that the modified layout can be a valuable solution for monitor-equipped devices with an extent smaller than 15 cm × 15 cm. Simulation results have been derived by using CST Microwave Studio commercial tool.

2. Overview on Wideband and High Efficiency Compact Planar Inverted-F Antennas

In Figure 1, a typical TV chassis is shown, where possible spaces available to locate an antenna are also highlighted. A number of DTV wideband antennas have been recently presented [2–11], which are mainly low-cost, low-profile, and easy-fabrication printed monopoles and patch-alike antennas. Printed monopoles require a careful positioning inside devices with high circuitry density, as they are quite sensitive to the presence of nearby metal parts. On the other hand, patch-alike antennas and PIFAs are suitable for integration because their ground plane also acts as a shield.

Figure 1: Example of a typical monitor chassis; the available space for the antenna is highlighted in a light color.

In this section, a review of some high efficiency (without any dielectric layer) PIFAs will be presented. In particular, antennas with a percentage bandwidth greater than 59% (i.e., the DVB-T %BW) have been taken into account. These antennas are suitable to be integrated into devices, such as a monitor or a TV chassis, where relatively large volumes are often available along their borders.

In [12], a PIFA with a percentage bandwidth of 65% and operating in the 1.6–3 GHz band for mobile applications (GSM, PCS, DCS, UMTS, WLAN, WiMax, and Bluetooth) has been presented. A so large impedance bandwidth can be achieved by optimizing the widths of the feeding and shorting plates (Figure 2).

Figure 2: A PIFA where bandwidth enlargement can be achieved by optimizing the widths of the feeding and shorting plates [12].

In [13], a PIFA configuration has been presented (Figure 3) which is made of a planar rectangular monopole top-loaded with a rectangular patch attached to two rectangular plates, one shorted to the ground and the other suspended. The fabricated antenna prototype has a measured impedance bandwidth of 125% (reflection coefficient lower than −10 dB in the 3–13 GHz band). The radiator size is 20 × 10 × 7.5 mm³, making the antenna electrically small over most of the band and suitable for integration in mobile devices.

Figure 3: A PIFA consisting of a planar rectangular monopole top-loaded with a rectangular patch attached to two rectangular plates, one is shorted to the ground and the other is suspended [13].

In [14], a capacitive feed is used to improve impedance characteristics (Figure 4). By changing three parameters (the area of the feed plate, the separation from the radiating top plate, and probe placement on the feed plate), antenna resonances can be controlled. The proposed design exhibits an impedance bandwidth ranging from 1.18 GHz to 2.24 GHz (61.92%).

Figure 4: A PIFA where a large impedance bandwidth has been obtained by using a capacitive feeding [14].

In [15], a modified PIFA (Figure 5) with a compact size of 34 mm × 8.0 mm × 8.0 mm has been proposed. The uniqueness of this design is the inclusion of both a T-shaped slot and a folded patch. The compact PIFA has a very wide 77% 10-dB impedance bandwidth (a larger bandwidth up to 81.3% has been measured on the prototype).

Figure 5: The inclusion of a T-shaped slot as well as a folded patch results in a wide impedance bandwidth in the PIFA presented in [15].

A UWB PIFA for the 2.4–6.2 GHz band (88.4% relative bandwidth), which is characterized by a driven (fed) radiating element separated by a small gap from a parasitic branch (Figure 6), has been presented in [16].

Figure 6: A PIFA characterized by a driven (fed) radiating element separated by a small gap from a parasitic branch [16].

Starting from the previous configurations, two high efficiency PIFAs have been presented in [18–20] for DVB-T band. A dual band functionality has been obtained by adding a new path in the antenna layout [18] or by using the small gap between the feed element and the parasitic one [19, 20].

Figure 7 shows the layout, the antenna prototype, and the main parameters of the PIFA proposed in [18] (named as Conf. A as shown in Figure 7).

Figure 7: Conf. A: 3D view.

Conf. A antenna (Figure 7) is composed of a series of branches, properly dimensioned and separated to generate the required resonances. The antenna exhibits a multiband functionality between 470 MHz and 862 MHz (59% percentage bandwidth) and between 3300 MHz and 3800 MHz (14% percentage bandwidth) for DVB-T and WiMAX applications, respectively. The final layout resulted from an optimization process focused to reduce the overall antenna dimensions as much as possible. The prototypes were fabricated with a 0.4 mm thick aluminum foil, properly cut and folded. This simplifies the antenna fabrication and avoids any soldering, except for that at the antenna connector.

The extent of the antenna proposed in [16] was also reduced in terms of wavelength in [19, 20], for the DVB-T and WLANs bands (named as Conf. B as shown in Figure 8).

Figure 8: Conf. B: 3D view.

The driven PIFA element acts as the primary element, governing the lowest resonant frequency, while the upper resonant frequency close to the DVB-T band is controlled by the parasitic element. Moreover, the separating gap helps in controlling a third resonance around 2.45 GHz in the IEEE 802.11b,g band for WLANs. Thus, as an improvement of the solution in [16], the proposed PIFA exhibits a dual band functionality. Moreover, if compared with [16], a significant reduction of 63% and 87% was achieved for the electrical thickness (H) and width (W), respectively (the electrical size is referred to the wavelength at the DVB-T band center frequency, where λ = 448 mm) at the cost of only 9% length (L) increase.

The 50 Ω-impedance matching was met for the two configurations (Conf. A and Conf. B) by optimizing the feeding plate shapes (the triangular plates connecting the feeding cables to the radiating elements in Figures 7 and 8) and the position of the shorting strip. The two PIFAs occupy an overall volume of 225 × 31 × 20 mm³ and 207 × 12 × 8 mm³, respectively. These radiating elements are relatively large with respect to antennas printed or mounted on high permittivity substrates, but, at the same time, they can guarantee higher gains and radiation efficiencies.

As shown in Figures 9 and 10, the measured reflection coefficients for Conf. A and Conf. B PIFAs are below −6 dB in the whole DVB-T band for both configurations and less than −10 dB in the WiMAX and IEEE 802.11b,g bands, respectively. The previous values are typical thresholds for integrated antennas for such communication standards.

Figure 9: Measured reflection coefficient for the two PIFAs in [16, 18], in the DVB-T band.

Figure 10: Measured reflection coefficient for the two PIFAs in [16, 18], in the WiMAX and WLAN bands, respectively.

The resonances in the DVB-T band for the two antenna configurations are mainly due to the plates of length L and the branches of length A and B. The PIFA height H is a critical parameter for obtaining the antenna impedance matching. For the Conf. A antenna, gain lies between 2.8 and 3.3 dBi in the lower band and between 3.2 dBi and 4.0 dBi in the WiMAX band.

The gain for the Conf. B is between 2.4 dBi and 3.3 dBi in the DVB-T band and between 4.4 dBi and 4.8 dBi in the WLAN band. The relatively high values obtained for the gain are due to the absence of a lossy dielectric under the radiating plate. A further analysis consisted in measuring the reflection coefficient variations when a metallic obstacle is located close to the antenna [19]. In particular, a large metallic plate (300 mm × 400 mm) was positioned in the vicinity of the antenna, at distances of 1 cm, 2 cm, and 3 cm. The numerical results demonstrated that the reflection coefficient variations are minimal. The robustness of the solution in terms of reflection coefficient variations with respect to the presence of near metal parts has been analyzed and checked through measurements too.

3. A Novel Dual-Band L-Shape Planar Inverted-F Antenna (PIFA)

Starting from the dual-band linear-shape PIFA described in [19], a modified layout suitable to be integrated along the corner of a compact monitor-equipped device (as shown in Figure 11) is here presented.

Figure 11: Example of a 3D view of a typical monitor chassis. The available space for the antenna is dark highlighted.

In [18–20], it has been verified that the total length L of a linear PIFA is a key parameter to achieve impedance matching at DVB-T band, and it should be greater than 20 cm to get satisfactory VSWR performance in the whole DVB-T frequency range.

It is worth noting that the new L-shape antenna configuration cannot be obtained by simply bending the antenna in [19], since all the basic antenna geometrical parameters need to be modified to optimize antenna performance (Figure 12). Table 1 shows the values of all geometrical parameters of the optimized L-shape PIFA.

Table 1: Dual-band L-shape PIFA dimensions (mm).

120

116

13

8

3.3

76.5

12

30.2

10

47

20

Figure 12: Geometry of the proposed dual-band L-shape PIFA.

In particular, the driven and parasitic elements jointly contribute to determine the two resonances at the DVB-T band. They can be controlled by varying the following parameters: W, H, L1 and L2. Also, the sum of the arm lengths, L1 and L2, must be retained greater than 20 cm. The width and the height of the radiating element have been set at 13 mm and 8 mm, respectively, as in [19]. Furthermore, the gap S between the two elements mainly affects the antenna reflection coefficient at the IEEE 802.11b,g band. The distance between the two radiating elements, S, and the distance of the feeding point from the edge, D, represent the most effective design parameters for antenna tuning. M and N variations cause the resonant frequency to shift in the IEEE 802.11b,g band; also, the reflection coefficient values increase at the DVB-T frequencies. As for the PIFAs in [18–20], the L-shape PIFA can be made out of a cut and bent single metal sheet.

3.1. Numerical Results for the Dual-Band L-Shape PIFA

Simulation results have been derived by using CST Microwave Studio commercial tool. The simulated reflection coefficient is below −6 dB and −10 dB in the DVB-T and WLAN bands, respectively. The simulated antenna gain (Figure 13) is between 1.8 dBi and 2.2 dBi in the DVB-T band and between 6.2 dBi and 6.4 dBi in the WLAN band; a radiation efficiency greater than 95% has been obtained at both frequency bands due to the absence of dielectric substrates.

Figure 13: Simulated gain for the proposed dual-band L-shape PIFA as a function of frequency.

The radiation pattern modifications have been analyzed and compared to those of the linear-shape PIFA in [19]. The simulated radiation patterns in the principal planes, XZ, YZ, and XY, are shown in Figure 14 ( and components, with all of them normalized to the electric field amplitude at ), when evaluated at the center frequency of the bands of interest. In the DVB-T band, the L-shape geometry causes a 45° rotation of the radiation pattern in the XY plane, as also apparent form the antenna gain 3D plots shown in Figures 15 and 16. In the other two principal planes (XZ and YZ), a 10° displacement from broadside of the component maximum occurs; the component exhibits an almost omnidirectional radiation pattern.

Figure 14: Simulated radiation patterns ( and components normalized to the electric field amplitude at ) for the proposed dual-band L-shape PIFA: (a) 670 MHz (central frequency for the DVB-T band); (b) 2440 MHz (central frequency for the IEEE 802.11b,g band).

Figure 15: Simulated 3D antenna gain (dBi) for the dual-band L-shape PIFA at 670 MHz.

Figure 16: Simulated 3D antenna gain (dBi) for the dual-band L-shape PIFA at 2440 MHz.

The radiation patterns in Figure 17 show that L-shape PIFA radiates a linearly polarized field in the plane. Also, it radiates as a combination of two orthogonal linear radiators that are fed in-phase. At higher frequency, in the WLAN band, a larger number of lobes is present, as expected since the antenna is electrically long at 2.4 GHz (see Figures 14 and 16).

(a)

(b)

Figure 17: Simulated radiation patterns ( and components normalized to the electric field amplitude at ) for the proposed dual-band L-shape PIFA at 670 MHz: (a) plane; (b) plane.

3.2. Experimental Results for the Dual-Band L-Shape PIFA

A prototype was realized with a 0.4 mm thick adhesive copper tape, cut and folded around a polystyrene block to obtain the final 3D structure. Results in terms of simulated and measured reflection coefficient are shown in Figure 18. The measured reflection coefficient is below −6 dB and −10 dB in the DVB-T and WLAN bands, respectively. Measurements on the radiation patterns have been performed at the anechoic chamber of the Department of Electrical Engineering of the University of Oviedo. The antenna prototype is shown in Figure 19 when it is mounted on the rotating platform for radiation pattern measurement.

Figure 18: Simulated and measured reflection coefficient for the proposed dual-band L-shape PIFA.

Figure 19: Antenna prototype mounted on the rotating platform for radiation pattern measurements.

The measured radiation patterns for the XZ and YZ planes, at 670 MHz and 2440 MHz, are compared with numerical simulations in Figures 20 and 21. Discrepancies between simulations and measurements are probably due to the limited mechanical robustness of the homemade prototype and the manufacturing inaccuracies. The measured antenna gain is about 1 dBi and 5 dBi for the DVB-T and the WLAN band, respectively (it is about 1 dB less than simulated results).

Figure 20: Simulated and measured radiation patterns (total E-field for the XZ and YZ planes) for the proposed dual-band L-shape PIFA at 670 MHz (central frequency for the DVB-T band).

Figure 21: Simulated and measured radiation patterns (total E-field for the XZ and YZ planes) for the proposed dual-band L-shape PIFA at 2440 MHz (central frequency for the IEEE 802.11b,g band).

4. Conclusions

Starting from an overview on compact Planar Inverted-F Antennas, a dual-band L-shape Planar Inverted-F Antenna operating in both the DVB-T band (470–862 MHz) and the WLAN IEEE 802.11b,g band (2400–2484 MHz) has been presented. It has been designed to meet space requirements typically required for integration along the corner of display-equipped devices. A prototype was realized and characterized. The L-shape PIFA can be obtained by properly cutting and folding a single metal sheet, thus resulting in a relatively low-cost and mechanically robust antenna configuration.

Although the final design here shown has been obtained by assuming specific requirements on the maximum length of the two arms of the L-shape PIFA (less than 15 cm for both arms), it has been numerically and experimentally verified that VSWR performance at the extremely large DVB-T frequency band can be still met by properly tuning antenna geometrical parameters, when the arm length requirements change less than 10% with respect to the lengths in Table 1. This confirms the robustness of the proposed L-shape PIFA design, which can be well optimized also when specific and demanding aesthetic/mechanical requirements must be met.

References

DVB Project, http://www.dvb.org/

K. L. Wong, C. I. Lin, T. Y. Wu, and J. W. Lai, “A planar DTV receiving antenna for laptop applications,” Microwave and Optical Technology Letters, vol. 42, no. 6, pp. 483–486, 2004.

C. M. Su, L. C. Chou, C. I. Lin, and K. L. Wong, “Internal DTV receiving antenna for laptop application,” Microwave and Optical Technology Letters, vol. 44, no. 1, pp. 4–6, 2005.

Y. W. Chi and K. L. Wong, “Wideband printed dipole antenna for DTV signal reception,” in Proceedings of IEEE Region 10 Conference (TENCON '07), pp. 1–4, November 2007.

W. S. Chen, Y. T. Chen, H. T. Chen, and J. S. Kuo, “A wideband printed monopole antenna for wireless applications,” in Proceedings of IEEE International Symposium on Antennas and Propagation and USNC/URSI National Radio Science Meeting (APSURSI '09), June 2009.

C. Yang, J. Kim, H. Kim, J. Wee, B. Kim, and C. Jung, “Quad-band antenna with high isolation MIMO and broadband SCS for broadcasting and telecommunication services,” IEEE Antennas and Wireless Propagation Letters, vol. 9, pp. 584–587, 2010.

C. Y. Huang, B. M. Jeng, and J. S. Kuo, “Grating monopole antenna for DVB-T applications,” IEEE Transactions on Antennas and Propagation, vol. 56, no. 6, pp. 1775–1776, 2008.

C. Y. Huang, B. M. Jeng, and C. F. Yang, “Wideband monopole antenna for DVB-T applications,” Electronics Letters, vol. 44, no. 25, pp. 1448–1450, 2008.

L. Low, J. Batchelor, R. Heaton, and N. Chen, “Dual patches microstrip fed antenna with wide bandwidth,” in Proceedings of the Loughborough Antennas and Propagation Conference (LAPC '09), pp. 429–432, November 2009.

M. Koubeissi, Mouhamadou, C. Decroze, D. Carsenat, and T. Monédière, “Triband compact antenna for multistandard terminals and user's hand effect,” International Journal of Antennas and Propagation, vol. 2009, Article ID 491262, 7 pages, 2009.

J. K. Wee, J. W. Park, I. S. Yeom, B. G. Kim, and C. W. Jung, “Compact DVB-H antenna with broad dual-band operation for PMP applications,” IEEE Antennas and Wireless Propagation Letters, vol. 9, pp. 580–583, 2010.

H. T. Chattha, Y. Huang, and Y. Lu, “PIFA bandwidth enhancement by changing the widths of feed and shorting plates,” IEEE Antennas and Wireless Propagation Letters, vol. 8, pp. 637–640, 2009.

C. See, H. Hraga, R. Abd-Alhameed, N. McEwan, J. Noras, and P. Excell, “A low-profile ultra-wideband modified planar inverted-F antenna,” IEEE Transactions on Antennas and Propagation, vol. 61, no. 1, pp. 100–108, 2012.

C. Suárez-Fajardo, J. O. Gómez-Sará, and M. Ferrando-Bataller, “Broadband PIFA with capacitive feed,” in Proceedings of IEEE International Symposium on Antennas and Propagation and USNC/URSI National Radio Science Meeting (APSURSI '09), pp. 1–4, June 2009.

H. Chaobin and Z. Qi, “A compact wideband PIFA for dual-band WLAN applications,” in Proceedings of the International Conference on Microwave and Millimeter Wave Technology (ICMMT '12), vol. 4, pp. 1–4, May 2012.

C. H. See, R. A. Abd-Alhameed, D. Zhou, and P. S. Excell, “A planar inverted-f-l antenna (pifla) with a rectangular feeding plate for lower-band uwb applications,” IEEE Antennas and Wireless Propagation Letters, vol. 9, pp. 149–151, 2010.

P. Nepa, G. Manara, A. A. Serra, and G. Nenna, “Multiband PIFA for WLAN mobile terminals,” IEEE Antennas and Wireless Propagation Letters, vol. 4, no. 1, pp. 349–350, 2005.

R. Caso, A. D'Alessandro, A. A. Serra, P. Nepa, and G. Manara, “An integrated dual-band PIFA for DVB-T and WiMAX applications,” IEEE Antenna and Wireless Propagation Letters, vol. 10, pp. 1027–1030, 2011.

R. Caso, A. D'Alessandro, A. A. Serra, P. Nepa P, and G. Manara, “A compact dual-band PIFA for DVB-T and WLAN applications,” IEEE Transaction on Antennas and Propagation, vol. 60, no. 4, pp. 2084–2087, 2012.

R. Caso, A. D'Alessandro, A. A. Serra, P. Nepa, and G. Manara, “Dual-band integrated G-PIFA antenna for DVB-T and WLAN applications,” in Proceedings of IEEE International Symposium on Antennas and Propagation, Spokane (AP-S '11), Washington, DC, USA, July 2011.