International Journal of Antennas and Propagation

Volume 2014 (2014), Article ID 951968, 6 pages

http://dx.doi.org/10.1155/2014/951968

Research Article

A CPW-Fed Rectangular Ring Monopole Antenna for WLAN Applications

Sangjin Jo, Hyunjin Choi, Beomsoo Shin, Sangyeol Oh, and Jaehoon Lee

Department of Computer and Radio Communication Engineering, Korea University, 1-5 Ka Anam-Dong, Seongbuk-gu, Seoul 136-701, Republic of Korea

Received 14 April 2014; Accepted 5 June 2014; Published 23 June 2014

Academic Editor: Nemai Karmakar

Copyright © 2014 Sangjin Jo et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

We present a simple coplanar waveguide- (CPW-) fed rectangular ring monopole antenna designed for dual-band wireless local area network (WLAN) applications. The antenna is based on a simple structure composed of a CPW feed line and a rectangular ring. Dual-band WLAN operation can be achieved by controlling the distance between the rectangular ring and the ground plane of the CPW feed line, as well as the horizontal vertical lengths of the rectangular ring. Simulated and measured data show that the antenna has a compact size of  mm², an impedance bandwidths of 2.21–2.70 GHz and 5.04–6.03 GHz, and a reflection coefficient of less than −10 dB. The antenna also exhibits an almost omnidirectional radiation pattern. This simple compact antenna with favorable frequency characteristics therefore is attractive for applications in dual-band WLAN.

1. Introduction

Wireless local area networks (WLANs), which enable user mobility, are considered to be a cost-effective solution for high-speed data connectivity. The growing demand for WLAN technology has led to interest in integrating the 2.412–2.482 GHz (IEEE802.11b/g) and 5.15–5.825 GHz (IEEE 802.11a) frequency bands into a single device that requires a dual-band antenna [1]. Numerous designs for dual-band antennas have been reported, including a dual-monopole antenna with different lengths [2] or sleeves [3], a bent folded monopole [4–6], a combination of monopole and helical antennas [7], and a slot antenna [8–10]. An antenna should exhibit impedance matching to the feed line, be low in cost and compact, and have a low profile, a high efficiency, and an omnidirectional radiation pattern. Broadband and omnidirectional characteristics of ring antennas have been reported [11–17]; however, to realize dual-band operation, additional structures must be employed on the bottom layer, such as a T-shape, S-shape, vertical strip resonator, or parasitic elements. Coplanar waveguide- (CPW-) fed antennas have received much attention because of their wide operating bandwidth, low profile, low cost, simple fabrication, potential for integration with monolithic microwave integrated circuits, and simple configuration using a single metallic layer [2, 16].

In this paper, we describe a design for rectangular ring-shaped monopole antenna that satisfies the 2.4-GHz and 5.2/5.8-GHz WLAN applications (i.e., it operates at frequencies in the range of 2.4–2.4835 GHz and 5.15–5.825 GHz). The antenna does not require any additional structures for dual-band WLAN operation. Through numerical simulations, we show that the distance between the rectangular ring and the ground plane, as well as the horizontal vertical lengths of the rectangular ring, can be optimized to control the resonant frequencies and hence achieve dual-band operation. Therefore, the proposed antenna achieved the small size, simple structure, and good frequency response with the omnidirectional radiation pattern.

2. Antenna Design

The geometry of the rectangular ring-shaped CPW-fed antenna is shown in Figure 1, together with a photograph of the fabricated optimized structure. The antenna had overall dimensions of 21.4 × 59.4 × 1.6 mm³ and was fabricated on an FR4 substrate with a relative permittivity of = 4.4. A 50- CPW transmission line with a signal strip width of 1.8 mm and a gap distance of 0.3 mm between the single strip and the coplanar ground plane was used to feed the antenna. The size of the rectangular ring was 11 × 20.5 mm², and the two ground planes with dimensions of 9.5 × 14 mm² were located symmetrically on each side of the CPW line. The antenna was symmetrical with respect to the longitudinal direction (i.e., the -axis).

(a)

(b)

(c)

Figure 1: Geometry of the printed rectangular ring antenna: (a) top view and (b) side view. (c) Photograph of the fabricated antenna.

To investigate the performance of the proposed antenna for dual-band operation, the commercially available simulation software HFSS was used. T-shaped or vertical strip resonators that correspond to radiation around 5 GHz are typically added to square ring structures to achieve dual-band operation [11–14]; however, with the antenna described here, we can achieve dual-band operation by controlling the distance between the rectangular ring and the ground plane, as well as the length and the width of the rectangular ring.

Figure 2(a) shows simulated data that reveal the effect of varying the distance between the rectangular ring and the ground plane on the return losses of the antenna. The parameter could be used to control the lower frequency and the upper band matching. Figure 2(b) shows the effects of varying the length of the rectangular ring on the return losses when the width of the antenna is fixed at = 5.5 mm. As the parameter increased, both the lower and upper resonant frequencies were red-shifted. Figure 2(c) shows the effect of varying when the width was fixed at = 20.5 mm. The parameter primarily affected the upper band; therefore, can be varied to tune the properties of the upper frequency band. The optimized antenna dimensions for operation at 2.4 GHz and 5.2/5.8 GHz are listed in Table 1.

Table 1: Antenna dimensions.

Parameters

Dimensions mm
21.4
59.4
21.4
14
1.8
0.3
1.6
4
20.5
5.5

(a)

(b)

(c)

Figure 2: Simulated return losses for various values of (a) , (b) , and (c) .

Figure 3 shows the simulated current distributions in the optimized structure at the different frequencies. The current distributions varied significantly depending on the resonant frequency. It is evident from these current distributions that, at a frequency of 2.4 GHz, the radiation mainly resulted from the vertical strip line of the rectangular ring. The current distributions at a frequency of 2.4 GHz are similar to resonant Path 1, as shown in Figure 1(a). The horizontal strip line of the rectangular ring contributed mainly to radiation at frequencies of 5.2 and 5.8 GHz. The resonant currents at frequencies of 5.2 and 5.8 GHz are distributed on the horizontal strip line which is similar to resonant Path 2, as shown in Figure 1(a). Hence, by appropriately adjusting the lengths of the vertical strip line and the horizontal strip line of the rectangular ring, the suitable resonant current paths can be created to radiate the electromagnetic energy at the different resonant frequencies.

(a)

(b)

(c)

Figure 3: Simulated current density distribution in the proposed antenna at (a) 2.4 GHz, (b) 5.2 GHz, and (c) 5.8 GHz.

3. Experiment Result

Figure 4 compares the simulated return losses with those measured from the fabricated antenna shown in Figure 1(c). Good agreement was evident between the simulated and measured data. At the lower resonant frequency of 2.4 GHz, the measured return loss was approximately −20 dB with a bandwidth of 500 MHz. At the upper resonant frequencies of 5.2 and 5.8 GHz, the return losses were less than −20 dB and the bandwidth was 1 GHz.

Figure 4: Comparison between the simulated and measured return losses for proposed antenna.

The measured x-y plane and z-x plane radiation patterns are shown in Figure 5. The electric field patterns exhibited some lobes in the radiation patterns, whereas the magnetic field distributions were almost completely omnidirectional. The measured peak gains in the 2.4-GHz and 5.2/5.8-GHz bands are shown in Figure 6; the peak antenna gain in the 2.4-GHz band was 2.0 dBi, and that in the 5.2/5.8-GHz band was 5.0 dBi.

(a)

(b)

(c)

Figure 5: Simulated and measured radiation patterns of the proposed antenna at (a) 2.4 GHz, (b) 5.2 GHz, and (c) 5.8 GHz.

Figure 6: Measured peak gain of the proposed antenna at operational frequency bands.

4. Conclusion

We have described a CPW-fed rectangular ring monopole antenna for WLAN applications. The antenna design is compact, with dimensions of only 21.4 × 59.4 × 1.6 mm³. The antenna had a simple geometry and is relatively easy to fabricate. Because the bandwidths of the lower and upper bands of the proposed antenna were sufficient for operation at the 2.4-GHz and 5.2/5.8-GHz bands, the antenna is suitable for dual-band WLAN applications. Furthermore, the antenna provides omnidirectional radiation patterns and stable gains within the bands, making this CPW-fed rectangular ring antenna design suitable for dual-band WLAN applications.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgment

This work was supported by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education, Science, and Technology (2012R1A1B3002517).

References

K. G. Thomas and M. Sreenivasan, “A simple dual-band microstrip-fed printed antenna for WLAN applications,” IET Microwaves, Antennas and Propagation, vol. 3, no. 4, pp. 687–694, 2009.

H.-D. Chen and H.-T. Chen, “A CPW-fed dual-frequency monopole antenna,” IEEE Transactions on Antennas and Propagation, vol. 52, no. 4, pp. 978–982, 2004.

M. Ali, M. Okoniewski, M. A. Stuchly, and S. S. Stuchly, “Dual-frequency strip-sleeve monopole for laptop computers,” IEEE Transactions on Antennas and Propagation, vol. 47, no. 2, pp. 317–323, 1999.

J.-. Lu and B.-. Huang, “Planar multi-band monopole antenna with L-shaped parasitic strip for WiMAX application,” Electronics Letters, vol. 46, no. 10, pp. 671–672, 2010.

W.-C. Liu and C.-M. Wu, “Dual-band CPW-fed G-shaped monopole antenna for 2.4/5GHz WLAN application,” PIERS Online, vol. 3, no. 7, pp. 1114–1118, 2007.

M. Samsuzzaman, T. Islam, N. H. Abd Rahman, M. R. I. Faruque, and J. S. Mandeep, “Coplanar waveguide fed compact wide circular-slotted antenna for Wi-Fi/WiMAX applications,” International Journal of Antennas and Propagation, vol. 2014, Article ID 982958, 10 pages, 2014.

P. Eratuuli, P. Haapala, and P. Vainikainen, “Dual frequency wire antennas,” Electronics Letters, vol. 32, no. 12, pp. 1051–1052, 1996.

Y.-X. Guo, K.-M. Luk, and K.-F. Lee, “Dual-band slot-loaded short-circuited patch antenna,” Electronics Letters, vol. 36, no. 4, pp. 289–291, 2000.

D. Parkash, R. Khanna, V. Kumar, and A. Chaudhary, “Novel dual-band CPW-fed monopole slot antenna for WLAN/WiMAX applications,” vol. 1, no. 1, 2010.

X. Y. Teng, X. M. Zhang, Z. X. Yang et al., “A compact CPW-fed omni-directional monopole antenna for WLAN and RFID applications,” Progress in Electromagnetics Research Letters, vol. 32, pp. 91–99, 2012.

Y. Seo, H. Lee, and Y. Lim, “Design of a circular ring monopole antenna with inverted T-strip line for dual-band operation,” Microwave and Optical Technology Letters, vol. 55, no. 9, pp. 2174–2176, 2013.

H.-J. Lee, H. Nam, and Y.-S. Lim, “A design of printed square loop antenna for omni-directional radiation patterns,” in Proceedings of the Radio Wireless Conference, pp. 253–256, 2003.

L. Zhang, Y.-C. Jiao, G. Zhao, Y. Song, and F. Zhang, “Broadband dual-band CPW-fed closed rectangular ring monopole antenna with a vertical strip for WLAN operation,” Microwave and Optical Technology Letters, vol. 50, no. 7, pp. 1929–1931, 2008.

Y. Xu, Y. C. Jiao, and Y. C. Luan, “Compact CPW-fed printed monopole antenna with triple-band characteristics for WLAN/WiMAX applications,” Electronics Letters, vol. 48, no. 24, pp. 1519–1520, 2012.

A. Wu and B. Guan, “A compact CPW-fed UWB antenna with dual band-notched characteristics,” International Journal of Antennas and Propagation, vol. 2013, Article ID 594378, 7 pages, 2013.

S.-W. Lee, N. Kim, S.-W. Park, S.-K. Jeon, and S.-Y. Rhee, “Design of trapezoidal ring antenna using conductor-backed CPW structure,” PIERS Online, vol. 5, no. 3, pp. 277–280, 2009.

Y. Li, W. Li, and Q. Ye, “A CPW-fed circular wide-slot UWB antenna with wide tunable and flexible reconfigurable dual notch bands,” The Scientific World Journal, vol. 2013, Article ID 402914, 10 pages, 2013.