International Journal of Antennas and Propagation
Volume 2017 (2017), Article ID 3859206, 10 pages
https://doi.org/10.1155/2017/3859206

Research Article

Broadband Circular Polarizer Based on Plasmon Hybridizations

Hong-Yu Shi,¹ Wei Li,² Shi-Tao Zhu,² Xiao-Li Dong,³ An-Xue Zhang,1,4 Song Xia,² and Zhuo Xu²

¹School of Electronic and Information Engineering, Xi’an Jiaotong University, Xi’an 710049, China
²Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education, Xi’an Jiaotong University, Xi’an 710049, China
³School of Telecommunication and Information Engineering, Xi’an University of Posts and Telecommunications, Xi’an 710061, China
⁴Beijing Center for Mathematics and Information Interdisciplinary Science (BCMIIS), Beijing 100048, China

Correspondence should be addressed to An-Xue Zhang; anxuezhang@mail.xjtu.edu.cn

Received 5 January 2017; Revised 11 February 2017; Accepted 20 February 2017; Published 7 March 2017

Academic Editor: Vincenzo Galdi

Copyright © 2017 Hong-Yu Shi et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

This paper presents a broadband circular polarizer with a ring/disk cavity structure, which is a broadband application of plasmon hybridizations. The proposed design can convert a linearly polarized wave to a circularly polarized wave from 12.66 GHz to 17.43 GHz within a bandwidth of 30%. The broadband polarization conversion characterization results from the different plasmon hybridization modes induced in the ring/disk cavity. The proposed broadband circular polarizer is demonstrated by both full-wave simulation and measurement.

1. Introduction

Metamaterials are artificial materials with properties which do not exist in natural material. They have been broadly used to control properties of the electromagnetic wave [1–3], especially the polarization [4–7]. Numerous metamaterial-inspired polarizers have been designed to change the polarization properties of antennas [8–12].

Plasmon resonances and plasmon hybridizations have been observed in metallic metamaterial structures [13, 14]. Plasmon hybridizations, including Fano resonances, can be induced within complex structures supporting multiple plasmon resonances even at microwave wavelengths. Fedotov et al. observed Fano resonance in a planar metallic metamaterial structure by introducing symmetry breaking [15]. These interesting phenomena have been applied for electromagnetic waves control, such as polarization converter [16, 17], absorber [18], and wave guiding and negative refraction [19, 20].

Metallic rings are highly tunable structures which can support multipolar plasmon modes at different frequencies under oblique incidence, retardation effects, or coupling with a disk [21]. Even and odd cavity resonant modes have been observed in elliptical plasmonic nanoantennas by azimuthal symmetry breaking, and these resonant modes have been applied to realize polarization conversion and absorption with a relatively low efficiency [22]. Using symmetry breakings, Fano resonance can also be raised in nonconcentric ring/disk cavities by the interaction between higher multipolar modes [23, 24]. Recently, various plasmon hybridization modes have been observed in highly tunable concentric ring/disk cavities at microwave band [25].

Khanikaev et al. designed an efficient ultra-thin circular polarizer using plasmon hybridizations in a unit cell with two topologically distinct structures. However, it only works at a single frequency [26]. Zhu et al. proposed a circular polarizer using electromagnetically induced transparency like (EIT-like) effect raised by two pairs of cut wires in the microwave band. However, the bandwidth of this design is only about 5.5% (from 9 GHz to 9.5 GHz) [27]. In this paper, a broadband circular polarizer is proposed using plasmon hybridizations in a ring/disk cavity. Different polarization selective plasmon hybridizations can be generated in the ring/disk cavity and cause a broadband circular polarization conversion from 12.66 GHz to 17.43 GHz within a bandwidth of about 30%.

2. Polarization Selected Plasmon Hybridizations in the Ring/Disk Cavity

The proposed ring/disk cavity is composed of an elliptical disk and a circular ring. The elliptical disk introduces anisotropic properties to the structure and makes the ring/disk cavity support different plasmon hybridization modes for different polarized incident waves at different frequencies. These plasmon hybridization modes can be observed through the distributions of the electric field Ez within the ring/disk cavity. We build a model in a commercial software CST MICROWAVE STUDIO as shown in Figure 1. In the simulation, the unit cell boundary condition is used along the and directions, and the absorbing boundary condition is applied in the direction. The model is excited by Floquet port with a normal incidence of linearly polarized waves in a frequency range of 10 GHz–18 GHz.

Figure 1: Schematic of the simulation.

Figure 2 shows the amplitudes of the reflectance under the illumination of waves polarized along the major axis and the minor axis of the elliptical disk. There is a dip at 17.5 GHz under major axis polarized incidence and a dip at 17.4 GHz under minor axis polarized incidence. Because of the metallic back sheet, the transmission is zero; thus, these reflectance dips are totally caused by the absorption. Both reflectances are bigger than 0.8 from 12 GHz to 17.43 GHz.

(a)

(b)

Figure 2: The amplitudes of the reflectance under the illumination of (a) major axis and (b) minor axis polarized waves.

The excited plasmon hybridization modes at different frequencies under major axis and minor axis polarized incidences are shown in Figure 3. In the ring/disk cavity, the different ring modes and disk modes couple to each other and generate different plasmon hybridizations.

(a)

(b)

Figure 3: The resonances in the ring/disk cavity: (a) under major axis polarized incidence; (b) under minor axis polarized incidence.

Figure 3(a) shows the plasmon hybridizations excited under the major axis polarized incidence. At 12 GHz, the dipolar ring mode is out phase with the e11 cavity mode [22] of the disk which causes a dark mode in the ring/disk cavity. At 15 GHz, the mimicking gap surface plasmons are generated [22] and in phase with the dipolar ring mode. The ring is excited in hexapole ring mode and is out of phase with the e11 disk mode at 16.5 GHz. At 17.5 GHz, the mimicking gap surface plasmons are stronger and in phase with the hexapole ring mode. The disk resonates in e12 mode [22] at 17.5 GHz. The hexapole ring mode, the e11 disk mode, and the mimicking gap surface plasmons are in phase with each other at 18 GHz.

Under minor axis polarized incidence, the resonances are shown in Figure 3(b). The dipolar ring mode is in phase with the o11 disk mode [22] at 12 GHz, 15 GHz, and 16 GHz. The mimicking gap surface plasmons generated from 16 GHz are in phase with the ring modes and stronger at higher frequency. The hexapole ring mode is out phase and in phase with the o11 disk mode at 17 GHz and 18 GHz, respectively.

Because of the metallic back sheet, the reflectance amplitude of major axis and minor axis polarized components are proximate to each other as shown in Figure 2. However, due to the anisotropic of the ring/disk cavity, the polarization selective plasmon hybridization modes have a strong influence on the reflection phase. As shown in Figure 4, a broadband reflection phase difference is raised between the major axis and minor axis polarized incidences from 12.66 GHz to 17.43 GHz. Thus, the polarization of the total reflected wave can be controlled by tuning the phase difference. If the phase difference is 90 deg, the total reflective wave will be converted to a circularly polarized wave within a bandwidth of about 30%.

Figure 4: The phase of the reflectance under major axis polarized incidence and minor axis polarized incidence, respectively.

3. Design of the Circular Polarizer

The proposed C2-symmetric ring/disk cavity can be used to realize a broadband circular polarizer as shown in Figure 5. The included angle between -axis and the major axis of the elliptical disk is 45 deg. The structures are printed on a TACONIC RF-35 slab with a thickness of  mm and a permittivity of 3.5. The loss tangent of the substrate is 0.003. The designed circular polarizers are etched from 0.035 mm flat copper on the substrate. A metallic sheet is on the other side of the substrate to confirm the reflection of the incident power.

Figure 5: The structure of the ring/disk cavity.

As shown in the Figure 5, under - or -polarized incidence, the incident wave can be decomposed into waves polarized along the major axis and the minor axis with the same amplitude and phase. Due to the anisotropy, the ring/disk cavity has different responses for major axis and minor axis polarized components. And the phase of these two components can be controlled independently by the geometrical parameters “” and “.” Thus, if the major axis and minor axis polarized components have similar amplitudes and a 90 deg phase difference, the total reflective wave will be circularly polarized.

Figure 6 shows the reflection phase for various values of . As shown in Figure 6(a), the reflection phase under major axis polarized incidence is larger with a smaller . However, the parameter has a negligible impact on the reflection phase under minor axis polarized incidence, as shown in Figure 6(b).

(a)

(b)

Figure 6: Reflection phase for various values of : (a) under major axis polarized incidence; (b) under minor axis polarized incidence.

As shown in Figure 7(a), the reflection phase can be hardly controlled by the values of under major axis polarized incidence. However, parameter has a strong impact on the reflection phase under minor axis polarized incidence, as shown in Figure 7(b). With a bigger , the reflection phase under major axis polarized incidence is smaller. Both and have a slight influence on the reflection phase at frequencies above 17.3 GHz.

(a)

(b)

Figure 7: Reflection phase for various values of : (a) under major axis polarized incidence; (b) under minor axis polarized incidence.

As shown in Figure 8, has a strong impact on the reflection phase at higher frequencies under both major and minor axis polarized incidences. With bigger , the reflection phase is smaller. Below 16.7 GHz, have little influence on the reflection phase, especially under major axis polarized incidence.

(a)

(b)

Figure 8: Reflection phase for various values of : (a) under major axis polarized incidence; (b) under minor axis polarized incidence.

As shown in Figure 9, only has a negligible impact on the reflection phase under both major and minor axis polarized incidences.

(a)

(b)

Figure 9: Reflection phase for various values of : (a) under major axis polarized incidence; (b) under minor axis polarized incidence.

With careful investigation, the geometrical parameters of the unit cell are chosen as  mm,  mm,  mm,  mm, and  mm to obtain a 90 deg phase difference between major and minor axis polarized incidence.

4. The Simulation and Measurement Results

Due to the C2-symmetry of the structure, the copolarized and cross-polarized reflected wave are of the same amplitude but with an opposite phase difference under - or -polarized incidence. Thus, the helicity of the reflective wave is opposite with - and -polarized illumination.

The simulated amplitude of the reflection coefficient is shown in Figure 10. refers to the amplitude of the -polarized component of the reflective wave when -polarized wave incidents with unit power, where the subscripts and could be or . From 12.66 GHz to 17.43 GHz, the amplitude of the - and -component of the reflective wave fluctuates around 0.7 within a limited range, under -polarized incidence. The central frequency is about 15 GHz, and the relative bandwidth is about 30%. Figure 11 shows the total reflection amplitude calculated by . From 12.66 GHz to 17.43 GHz, the total reflection amplitude is above 0.8.

Figure 10: The simulated reflectance of the broadband circular polarizer.

Figure 11: The total reflection amplitude.

The phase difference of the - and -component of the reflective wave under -polarized incidence is shown in Figure 12. From 12 GHz to 17.43 GHz, the phase difference of the - and -component of the reflective wave is about 90 deg. Thus, from 12.6 GHz to 17.43 GHz, the reflective wave is left-handed circularly polarized.

(a)

(b)

Figure 12: The phase (a) and the phase difference (b) of the -polarized and -polarized reflectance.

For a further insight of the reflective wave, the ellipticity of the reflective wave is calculated by , where and are the phase difference and amplitude ratio of the - and -component of the reflective wave, respectively. When the ellipticity is negative, the reflective wave is left-handed circularly or elliptically polarized. The reflective wave is pure left-handed circularly wave if the ellipticity is −45 deg. Figure 13 shows the calculated ellipticity which fluctuates around −40 deg and equals −45 deg at 13.1 GHz, 15.07 GHz, and 16.9 GHz.

Figure 13: The calculated ellipticity.

To further evaluate the circular polarization property of the reflective wave, the axial ratio is calculated by and shown in Figure 14, which indicates that the axial ratio is below 3 dB from 12.66 GHz to 17.43 GHz. Thus, the reflected wave can be considered as a left-handed circularly polarized wave.

Figure 14: The calculated axial ratio.

A sample is fabricated and measured to demonstrate the properties of the circular polarizer as shown in Figure 15. As shown in Figure 15(b), an -polarized horn is used as a source; the - and -components of the reflective wave are received by the - and -polarized horns, respectively, with a vector network analyzer (Agilent E8363b). The amplitude and phase of the measured reflectance are shown in Figures 16 and 17. The axial ratio calculated from the measurement results is shown in Figure 18. The measurement results confirm the simulation results, and the differences in the simulation results are caused by the machining error and the measurement error.

(a)

(b)

Figure 15: (a) Photo of the fabricated sample; (b) schematic of the measurement.

Figure 16: The measured reflectance.

(a)

(b)

Figure 17: The measured reflectance: (a) phase; (b) phase difference.

Figure 18: The measured axial ratio.

5. Conclusion

In this paper, a broadband circular polarizer is designed using a ring/disk cavity. Different plasmon hybridizations are excited in the ring/disk cavity at different frequencies, which cause a broadband 90 deg phase difference between the major axis and minor axis polarized reflective waves from 12.66 GHz to 17.43 GHz. Thus, a linearly polarized incident wave can be converted to a circularly polarized wave within a bandwidth of about 30%.

Conflicts of Interest

The authors declare that they have no competing interests.

Acknowledgments

This work was supported by the National Natural Science Foundation of China (Grant nos. 61501365, 61471292, 61601360, 61471388, and 61331005) and China Postdoctoral Science Foundation (Grant no. 2015M580849).

References

S. Liu, T. J. Cui, Q. Xu et al., “Anisotropic coding metamaterials and their powerful manipulation of differently polarized terahertz waves,” Light: Science and Applications, vol. 5, Article ID e16076, 2016.

S. Liu, Q. Cheng, Q. Xu et al., “Free-standing metasurfaces for high-efficiency transmitarrays for controlling terahertz waves,” Advanced Optical Materials, vol. 4, no. 3, pp. 384–390, 2016.

H.-T. Chen, A. J. Taylor, and N. Yu, “A review of metasurfaces: physics and applications,” Reports on Progress in Physics, vol. 79, no. 7, Article ID 076401, 2016.

P. Ginzburg, F. J. Rodríguez-Fortuño, A. Martínez, and A. V. Zayats, “Analogue of the quantum hanle effect and polarization conversion in non-hermitian plasmonic metamaterials,” Nano Letters, vol. 12, no. 12, pp. 6309–6314, 2012.

H. Shi, A. Zhang, S. Zheng, J. Li, and Y. Jiang, “Dual-band polarization angle independent 90° polarization rotator using twisted electric-field-coupled resonators,” Applied Physics Letters, vol. 104, no. 3, Article ID 034102, 2014.

S. J. Li, X. Y. Cao, L. M. Xu et al., “Ultra-broadband reflective metamaterial with RCS reduction based on polarization convertor, information entropy theory and genetic optimization algorithm,” Scientific Reports, vol. 5, article 37409, 2016.

H. Chen, J. Wang, H. Ma et al., “Ultra-wideband polarization conversion metasurfaces based on multiple plasmon resonances,” Journal of Applied Physics, vol. 115, no. 15, Article ID 154504, 2014.

T. Tuovinen, E. T. Salonen, and M. Berg, “An artificially anisotropic antenna substrate for the generation of circular polarization,” IEEE Transactions on Antennas and Propagation, vol. 64, no. 11, pp. 4937–4942, 2016.

W. Li, S. Xia, B. He et al., “A reconfigurable polarization converter using active metasurface and its application in horn antenna,” IEEE Transactions on Antennas and Propagation, vol. 64, no. 12, pp. 5281–5290, 2016.

X. Ma, C. Huang, W. Pan, B. Zhao, J. Cui, and X. Luo, “A dual circularly polarized horn antenna in Ku-band based on chiral metamaterial,” IEEE Transactions on Antennas and Propagation, vol. 62, no. 4, pp. 2307–2311, 2014.

H. Shi, J. Chen, A. Zhang, and Y. Jiang, “Design of a circular polarized horn antenna with an anisotropic metamaterial slab,” Frequenz, vol. 67, no. 9-10, pp. 271–276, 2013.

F. Yang and Y. Rahmat-Samii, “A low profile single dipole antenna radiating circularly polarized waves,” IEEE Transactions on Antennas and Propagation, vol. 53, no. 9, pp. 3083–3086, 2005.

F. Monticone and A. Alù, “Metamaterials and plasmonics: from nanoparticles to nanoantenna arrays, metasurfaces, and metamaterials,” Chinese Physics B, vol. 23, no. 4, Article ID 047809, 2014.

B. Luk'Yanchuk, N. I. Zheludev, S. A. Maier et al., “The Fano resonance in plasmonic nanostructures and metamaterials,” Nature Materials, vol. 9, no. 9, pp. 707–715, 2010.

V. A. Fedotov, M. Rose, S. L. Prosvirnin, N. Papasimakis, and N. I. Zheludev, “Sharp trapped-mode resonances in planar metamaterials with a broken structural symmetry,” Physical Review Letters, vol. 99, no. 14, Article ID 147401, 2007.

G.-X. Dong, H.-Y. Shi, S. Xia et al., “Ultra-broadband and high-efficiency polarization conversion metasurface with multiple plasmon resonance modes,” Chinese Physics B, vol. 25, no. 8, Article ID 084202, 2016.

F. Wang, A. Chakrabarty, F. Minkowski, K. Sun, and Q.-H. Wei, “Polarization conversion with elliptical patch nanoantennas,” Applied Physics Letters, vol. 101, no. 2, Article ID 023101, 2012.

P. V. Tuong, J. W. Park, V. D. Lam, W. H. Jang, S. A. Nikitov, and Y. P. Lee, “Dielectric and Ohmic losses in perfectly absorbingmetamaterials,” Optics Communications, vol. 295, pp. 17–20, 2013.

V. A. Podolskiy, A. K. Sarychev, and V. M. Shalaev, “Plasmon modes and negative refraction in metal nanowire composites,” Optics Express, vol. 11, no. 7, pp. 735–745, 2003.

H. Lu, X. Liu, D. Mao, and G. Wang, “Plasmonic nanosensor based on Fano resonance in waveguide-coupled resonators,” Optics Letters, vol. 37, no. 18, pp. 3780–3782, 2012.

F. Hao, E. M. Larsson, T. A. Ali, D. S. Sutherland, and P. Nordlander, “Shedding light on dark plasmons in gold nanorings,” Chemical Physics Letters, vol. 458, no. 4-6, pp. 262–266, 2008.

A. Chakrabarty, F. Wang, F. Minkowski, K. Sun, and Q.-H. Wei, “Cavity modes and their excitations in elliptical plasmonic patch nanoantennas,” Optics Express, vol. 20, no. 11, pp. 11615–11624, 2012.

Y. Sonnefraud, N. Verellen, H. Sobhani et al., “Experimental realization of subradiant, superradiant, and fano resonances in ring/disk plasmonic nanocavities,” ACS Nano, vol. 4, no. 3, pp. 1664–1670, 2010.

F. Hao, Y. Sonnefraud, P. Van Dorpe, S. A. Maier, N. J. Halas, and P. Nordlander, “Symmetry breaking in plasmonic nanocavities: subradiant LSPR sensing and a tunable Fano resonance,” Nano Letters, vol. 8, no. 11, pp. 3983–3988, 2008.

H. Shi, J. Li, A. Zhang, J. Wang, and Z. Xu, “Broadband cross polarization converter using plasmon hybridizations in a ring/disk cavity,” Optics Express, vol. 22, no. 17, pp. 20973–20981, 2014.

A. B. Khanikaev, S. H. Mousavi, C. Wu, N. Dabidian, K. B. Alici, and G. Shvets, “Electromagnetically induced polarization conversion,” Optics Communications, vol. 285, no. 16, pp. 3423–3427, 2012.

L. Zhu, F.-Y. Meng, L. Dong, J.-H. Fu, F. Zhang, and Q. Wu, “Polarization manipulation based on electromagnetically induced transparency-like (EIT-like) effect,” Optics Express, vol. 21, no. 26, pp. 32099–32110, 2013.