In this paper, we propose a reconfigurable metasurface antenna for beam switching applications. The reconfigurable metasurface is formed by uniformly distributed double-split square rings loaded with positive-intrinsic-negative (PIN) diodes for dual operations of a wave reflector and a wave director. Specifically, when the PIN diodes are forward biased, an epsilon-negative (ENG) metasurface is realized which reflects all incident waves with appropriate polarization; when the diodes are reverse biased, at the same operating frequency, a mu-near-zero (MNZ) metasurface is acquired which directs wave propagation. For excitation, a dipole radiator loaded with the same type of PIN diode is designed. Simulation and measurement results show good agreement and verify the beam switching functionality of the proposed metasurface antenna.
Thailand Research FundRTA6080008RSA59800511. Introduction
Recent advances in metamaterial and metasurface technologies have brought unprecedented opportunities in the realization of novel and practical electromagnetic structures and devices. By definition, metamaterials are artificial periodic structures with unusual electromagnetic properties such as negative permittivity and permeability that have not been found in naturally occurring materials [1], and metasurfaces are referred to as metamaterials with reduced dimensions [2, 3]. In addition to having low profile, metasurfaces offer even more functionality and flexibility in the design of electromagnetic structures and provide a higher degree of control over wave propagations. Typical applications of metasurfaces include wavefront control (according to the generalized Snell’s law [4]) using planar lenses, vortex generator, and axicon [5, 6]; super-resolution imaging and lithography by utilizing evanescent waves [7]; radar cross-section (RCS) reduction [8]; and realization of electromagnetic absorbers and polarization converters.
Reconfigurable metasurfaces, recently attracting a considerable amount of interest, have the advantage of providing multifunctional control of electromagnetic waves with electrical tuning mechanisms such as changing the applied bias voltage. Typical active elements used in reconfigurable metasurfaces include positive-intrinsic-negative (PIN) diodes, varactors, or transistors, which have been utilized to achieve beam steering [9–15], polarization conversion and control [16–20], realization of compact absorbers [21, 22], and recently, proposed coding or programmable metasurfaces [23–28].
In this work, we propose a PIN diode-based reconfigurable metasurface for realization of dual operations when the diode is in different bias states. Specifically, when the PIN diode is forward biased, at the frequency of interest, the metasurface acquires the properties of epsilon-negative (ENG) materials which forbid wave propagation and reflect all incident waves with appropriate polarization; when the diode is in its reverse-biased state, the metasurface obtains properties of mu-near-zero (MNZ) materials which direct wave propagation [29–32]. Based on these two controllable functions of the proposed metasurface, we then further design a feeding dipole radiator to realize a compact beam switching antenna, and its radiation patterns can be electrically controlled by the applied bias voltage across the PIN diode. In contrast to our previous work on the realization of contrary beams at different frequencies [33], the PIN diode-based metasurface proposed in this paper allows to generate antenna beams in opposite directions at the same operating frequency.
2. Reconfigurable Metasurface Antenna Design
It is well known that most metasurfaces are formed by resonant structures such as split-ring resonators (SRRs). Thus, below the resonant frequency, the metasurface has positive material properties, while the permittivity or permeability of the metasurface becomes negative at frequencies above the resonance. Naturally, different wave behaviors through the same metasurface can be acquired depending on the operating frequency range. However, for most practical applications such as wireless communications, the operating frequencies must be fixed, and therefore, to achieve multifunctional operations, the metasurface needs to be tunable or reconfigurable. With the use of PIN diode in the metasurface design, the resonant frequency can be controlled by the applied bias voltage, and different properties of the metasurface can be obtained at the same operating frequency.
Here, we consider a metasurface formed by periodically arranged double-split square rings whose fundamental resonant frequency can be conveniently controlled by the dimensions of each ring. In addition, to realize a reconfigurable metasurface, two PIN diodes (Infineon BAR63-03W) are inserted into the gaps of each square ring, as shown in Figure 1(a).
(a) Unit cell of the metasurface formed by square split rings loaded with two PIN diodes. (b) Equivalent circuits of the PIN diode in the forward and reverse bias states (Ls=1.8nH, Rs=1Ω, Rp=5kΩ, and CT=0.3pF). (c) Calculated transmission and reflection coefficients and retrieved relative permittivity and permeability of the metasurface formed by double-split square rings loaded with PIN diodes in forward and reverse bias states.
The equivalent circuits of the PIN diode in its forward and reverse bias states are shown in Figure 1(b). A plane-wave analysis is then performed to calculate the transmission and reflection coefficients of the metasurface and a material parameter retrieval method is applied to extract effective permittivity and permeability of the metasurface, as shown in Figure 1(c). It is found that when the PIN diodes are in different bias states, there exist two resonant frequencies of the metasurface, which can be explained as follows. When the diode is forward biased, each square ring of the metasurface becomes a closed loop due to the small resistance, Rs, leading to a lower resonant frequency of the metasurface. When the diode is reverse biased, as shown in Figure 1(b), the small capacitance, CT lowers the total capacitance of each square ring and causes the resonant frequency of the metasurface to shift higher. An alternation explanation of the operating mechanism is that the ring inclusions act as simple loaded electrically small dipoles (the vertical metallic segments along the y direction), and the capacitive loads applied to the end of small dipoles contribute to reduce their dimensions, then the inductor Ls in the gap introduced by the PIN diode further contributes to reduce the resonant frequency. When the PIN diodes are reverse biased, the capacitance CT reduces the impact of Ls in the equivalent circuit model and the resonant frequency blueshifts.
At the frequency of interest at around 2.45 GHz, for the forward bias case, the effective permittivity, εx, is negative, while the effective permeability, μy, is near zero but positive. Thus, an ENG metasurface is realized which forbids wave propagation and reflects all incident waves with x polarization. When the diodes are reverse biased, the upshift of the resonant frequency results in a positive εx while μy still remains near zero, creating a MNZ metasurface at the same frequencies around 2.45 GHz. Although observed from the transmission and reflection coefficients that the metasurface is still highly reflective for plane waves, the MNZ metasurface is capable of altering wave vectors of near fields and acting as a wave director, according to our previous analysis [29–32]. Thus, a reconfigurable PIN diode-based metasurface is realized to achieve dual functionality of a wave reflector and a wave director depending on the applied bias voltage. Based on these two functions, in the following, we further design a reconfigurable beam switching antenna.
In the metasurface antenna design, the number of elements in the metasurface is 3×3 in order to maintain the overall small dimensions of the antenna, as shown in Figure 2(a).
Structure of the proposed PIN diode-based reconfigurable metasurface antenna for beam switching applications: (a) perspective view and (b) the dipole excitation source. (c) Diagram showing how PIN diodes are connected to two radiating arms of the dipole.
For excitation, a dipole radiator is designed which contains two identical radiating arms with one arm on each side of a substrate. Both radiating arms are aligned along x direction to excite the correct polarization. A PIN diode (the same model as above) is also used in each radiating arm of the dipole radiator for tuning its resonant frequency, as the metasurface introduces different mutual coupling effects to the dipole when the PIN diodes on the metasurface are in different bias states. As illustrated in Figure 2(b), the PIN diode separates each radiating arm into a long section and a short section. For biasing both diodes at the same time, the long section on one side is connected by a thin wire to the short section on the other side, as depicted in Figure 2(c). The antenna is simulated using CST Microwave Studio™, and all parameters shown in Figure 2 are optimized ones, including the distance between the two substrates. The distance is chosen such that the antenna has high directivity when the diodes are in both bias states.
3. Results and Discussions
The proposed metasurface antenna is fabricated on FR-4 substrates with thickness of 1.6 mm and dielectric constant of 4.3. The prototype of the antenna and the measurement setup are shown in Figure 3.
Prototype of the fabricated PIN diode-based reconfigurable metasurface antenna: (a) top view of the reconfigurable metasurface and (b) bottom view of the dipole excitation source. (c, d) Experimental setup during the measurement of the radiation patterns (gain) of the proposed reconfigurable metasurface antenna.
Two 9-volt parallel-connected batteries are used to bias the PIN diodes on the metasurface, and a bias tee is used to combine the radio frequency (RF) signal and direct current (DC) bias voltage for feeding the dipole radiator.
Figure 4 shows the comparison of simulated and measured return loss and antenna gains in the forward (+z) and backward (−z) directions when the PIN diodes are in different bias states. When the PIN diodes on the metasurface are forward biased, the mutual coupling between the metasurface and dipole radiator lowers the dipole’s resonant frequency; thus, a reverse bias voltage is applied to the PIN diodes on the dipole to shorten the electrical length of its radiating arms.
Comparison of simulated and measured (a) return loss and (b) gain of the proposed PIN diode-based reconfigurable metasurface antenna operating in forward and reverse bias states of PIN diodes. (Notations: MS: metasurface; FW: forward bias; RV: reverse bias.)
On the other hand, when the PIN diodes on the metasurface are reverse biased, the resonant frequency of the dipole radiator shifts higher and a forward bias voltage is applied to the PIN diodes on the dipole to shift the resonance back to 2.45 GHz. Therefore, to conclude, when the metasurface is working as a wave reflector, the PIN diodes on the metasurface and dipole are forward and reverse biased, respectively; when the metasurface is acting as a wave director, the PIN diodes on the metasurface and dipole are reverse and forward biased, respectively. In addition, it can be observed that the metasurface antenna has good impedance matching for both diode states. The difference in antenna gains in Figure 4(b) is due to the fact that the efficiency of the metasurface behaving as a wave reflector is higher than that as a wave director [29–32].
The calculated three-dimensional (3-D) radiation patterns (gain) from CST simulations and the comparison between simulated and measured radiation patterns are shown in Figures 5 and 6, respectively.
Simulated 3-D radiation patterns (normalized gain) of the proposed PIN diode-based reconfigurable metasurface antenna operating in forward and reverse bias states of PIN diodes at frequencies of 2.4, 2.45, and 2.5 GHz.
Comparison of radiation patterns (gain) in the x-z planes from simulations and measurement at the frequencies of 2.4, 2.45, and 2.5 GHz.
It can be clearly observed that when the PIN diodes on the metasurface are forward biased, the main antenna beam points toward the −z direction, and when the diodes on the metasurface are reverse biased, the main antenna beam is directed to the +z direction. Thus, the antenna beam can be switched conveniently according to the applied bias voltage. Moreover, the comparison between simulation and measurement results also shows good agreement which validates our proposed design.
4. Conclusion
In conclusion, we have proposed a PIN diode-based reconfigurable metasurface antenna for beam switching applications. The metasurface is designed for dual operations of a wave reflector and a wave director, by realizing an ENG metasurface and a MNZ metasurface at the same operating frequency when the diodes are in forward and reverse bias states, respectively. Simulation and experimental results show that the proposed antenna has good impedance matching with moderate gain performance across the frequency band of interest. In addition, the main radiation beam of the metasurface antenna can be readily controlled by applying appropriate bias voltages on the PIN diodes.
Data Availability
The data used to support the findings of this study are available from the corresponding author upon request.
Conflicts of Interest
The authors declare that they have no conflicts of interest.
Acknowledgments
This work is supported by the Thailand Research Fund (TRF) under grant numbers RSA5980051 and RTA6080008.
VeselagoV. G.The electrodynamics of substances with simultaneously negative values of ε and μ196810450951410.1070/PU1968v010n04ABEH003699HollowayC. L.KuesterE. F.GordonJ. A.O'HaraJ.BoothJ.SmithD. R.An overview of the theory and applications of metasurfaces: the two-dimensional equivalents of metamaterials2012542103510.1109/MAP.2012.62307142-s2.0-84856956120KildishevA. V.BoltassevaA.ShalaevV. M.Planar photonics with metasurfaces20133396125123200910.1126/science.12320092-s2.0-8487498965723493714YuN.GenevetP.KatsM. A.AietaF.TetienneJ.-P.CapassoF.GaburroZ.Light propagation with phase discontinuities: generalized laws of reflection and refraction2011334605433333710.1126/science.12107132-s2.0-8005483812721885733AietaF.GenevetP.KatsM. A.YuN.BlanchardR.GaburroZ.CapassoF.Aberration-free ultra-thin flat lenses and axicons at telecom wavelengths based on plasmonic metasurfaces20121294932493610.1021/nl302516v2-s2.0-8486634247222894542GenevetP.YuN.AietaF.LinJ.KatsM. A.BlanchardR.ScullyM. O.GaburroZ.CapassoF.Ultra-thin plasmonic optical vortex plate based on phase discontinuities20121001, article 01310110.1063/1.36733342-s2.0-84858271620FangN.LeeH.SunC.ZhangX.Sub-diffraction-limited optical imaging with a silver superlens2005308572153453710.1126/science.11087592-s2.0-1764441966915845849ModiA. Y.BalanisC. A.BirtcherC. R.ShamanH. N.Novel design of ultrabroadband radar cross section reduction surfaces using artificial magnetic conductors201765105406541710.1109/TAP.2017.27340692-s2.0-85028915798TianS.LiuH.LiL.Design of 1-bit digital reconfigurable reflective metasurface for beam-scanning20177988210.3390/app70908822-s2.0-85028368241XieP.WangG.CaiT.LiH.LiangJ.Novel fabry-pérot cavity antenna with enhanced beam steering property using reconfigurable meta-surface2017123746210.1007/s00339-017-1060-92-s2.0-85020255765RatniB.de LustracA.PiauG. P.BurokurS. N.Reconfigurable meta-mirror for wavefronts control: applications to microwave antennas20182632613262410.1364/OE.26.0026132-s2.0-8504145513729401798SleasmanT.BoyarskyM.Pulido-ManceraL.FromentezeT.ImaniM. F.ReynoldsM. S.SmithD. R.Experimental synthetic aperture radar with dynamic metasurfaces201765126864687710.1109/TAP.2017.27587972-s2.0-85030766596YurdusevenO.MarksD. L.FromentezeT.SmithD. R.Dynamically reconfigurable holographic metasurface aperture for a Mills-Cross monochromatic microwave camera20182655281529110.1364/OE.26.0052812-s2.0-8504280377629529733HuangC.ZhangC.YangJ.SunB.ZhaoB.LuoX.Reconfigurable metasurface for multifunctional control of electromagnetic waves2017522, article 170048510.1002/adom.2017004852-s2.0-85034076596XuH.-X.TangS.MaS.LuoW.CaiT.SunS.HeQ.ZhouL.Tunable microwave metasurfaces for high-performance operations: dispersion compensation and dynamical switch2016613825510.1038/srep382552-s2.0-8499909896527901088YangH.CaoX.YangF.GaoJ.XuS.LiM.ChenX.ZhaoY.ZhengY.LiS.A programmable metasurface with dynamic polarization, scattering and focusing control2016613569210.1038/srep356922-s2.0-8499259341327774997TaoZ.WanX.PanB. C.CuiT. J.Reconfigurable conversions of reflection, transmission, and polarization states using active metasurface201711012, article 12190110.1063/1.49790332-s2.0-85016161815HuJ.LuoG. Q.HaoZ.-C.A wideband quad-polarization reconfigurable metasurface antenna201866130613710.1109/ACCESS.2017.27662312-s2.0-85032433034ZhuH. L.CheungS. W.LiuX. H.YukT. I.Design of polarization reconfigurable antenna using metasurface20146262891289810.1109/TAP.2014.23102092-s2.0-84902009138LiW.XiaS.HeB.ChenJ.ShiH.ZhangA.LiZ.XuZ.A reconfigurable polarization converter using active metasurface and its application in horn antenna201664125281529010.1109/TAP.2016.26204842-s2.0-85006102525YooM.LimS.Active metasurface for controlling reflection and absorption properties2014711, article 11220410.7567/APEX.7.1122042-s2.0-84910012826LiA.LuoZ.WakatsuchiH.KimS.SievenpiperD. F.Nonlinear, active, and tunable metasurfaces for advanced electromagnetics applications20175274392745210.1109/ACCESS.2017.27762912-s2.0-85035752132LiL.Jun CuiT.JiW.LiuS.DingJ.WanX.Bo LiY.JiangM.QiuC. W.ZhangS.Electromagnetic reprogrammable coding metasurface holograms20178119710.1038/s41467-017-00164-92-s2.0-8502677326228775295CuiT. J.LiuS.ZhangL.Information metamaterials and metasurfaces20175153644366810.1039/C7TC00548B2-s2.0-85017595348CuiT. J.QiM. Q.WanX.ZhaoJ.ChengQ.Coding metamaterials, digital metamaterials and programmable metamaterials20143, article e21810.1038/lsa.2014.99ZhangL.LiuS.LiL.CuiT. J.Spin-controlled multiple pencil beams and vortex beams with different polarizations generated by Pancharatnam-Berry coding metasurfaces2017941364473645510.1021/acsami.7b124682-s2.0-8503173336528944660ZhangL.WuR. Y.BaiG. D.WuH. T.MaQ.ChenX. Q.CuiT. J.Transmission-reflection-integrated multifunctional coding metasurface for full-space controls of electromagnetic waves20182833, article 180220510.1002/adfm.2018022052-s2.0-85051417921ZhangL.WanX.LiuS.YinJ. Y.ZhangQ.WuH. T.CuiT. J.Realization of low scattering for a high-gain Fabry-Perot antenna using coding metasurface20176573374338310.1109/TAP.2017.27008742-s2.0-85029713818ChaimoolS.RaklueaC.AkkaraekthalinP.Mu-near-zero metasurface for microstrip-fed slot antennas2013112366967510.1007/s00339-013-7703-62-s2.0-84881316325ZhaoY.Nondiffracting beam emission from hyperbolic metasurfaces2015174, article 04510310.1088/2040-8978/17/4/0451032-s2.0-84925710928ZhaoY.Design of high-gain, wideband antenna using microwave hyperbolic metasurface201665, article 05502210.1063/1.49527522-s2.0-84971223719HongnaraT.ChaimoolS.AkkaraekthalinP.ZhaoY.Design of compact beam-steering antennas using a metasurface formed by uniform square rings201869420942910.1109/ACCESS.2018.27995512-s2.0-85041426805HongnaraT.ChaimoolS.AkkaraekthalinP.Anisotropic fractal metasurface-based antenna with contrary beams201759371572010.1002/mop.303782-s2.0-85010380358