Nanogold doped TiO2 catalysts are synthesized, and their application in the photodegradation of dye pollutants is studied. The materials are characterized using different analytical techniques such as X-ray diffraction, transmission electron microscopy, UV-visible diffuse reflectance spectroscopy, and X-ray photoelectron spectroscopy. The results revealed the strong interaction between the metallic gold nanoparticles and the anatase TiO2 support. Au doped systems showed very good photoactivity in the degradation of dye pollutants under UV irradiation as well as in sunlight. A simple mechanism is proposed for explaining the excellent photoactivity of the systems. The reusability studies of the photocatalysts exhibited more than 98% degradation of the dye even after 10 repeated cycles.
1. Introduction
Even though dyes are classified as pollutants, they are widely applied in the textile manufacturing industries. The discharge of dyes causes soil as well as water pollution depending on its mode of disposal. In addition, since the dye stuffs are intentionally designed to resist aerobic oxidation by microorganisms, only partial degradation of dye molecules are possible with aerobes, and it results in the formation of volatile carcinogenic compounds. So the treatment of these dye effluents is highly desired for the preservation of clean air, soil, and water.
TiO2, in the anatase form, is one of the best photocatalysts for pollutant degradation [1]. However, because of the relatively high intrinsic band gap of anatase TiO2 (3.2 eV), ultraviolet (UV) irradiation is required for its photoactivity [2, 3], and thus only 4% of the sunlight (UV fraction of solar spectrum) can be utilized effectively [4]. Thus, pure TiO2 based systems have been found to be inactive under sunlight. Application of UV lamps has serious disadvantages including high energy consumption and handling problems. Keeping this in mind, researchers focused to develop TiO2 based systems having decreased band gap so as to show photocatalytic activity in the visible region. This will enable the use of sunlight for photocatalysis [5]. Several modification methods are available to shift the wavelength of absorption of TiO2 from UV to visible region, among which anion doping succeed in this matter [6–11]. Nitrogen is the widely studied anion dopant where the photoactivity of the N doped TiO2 even arises by the presence of molecularly adsorbed N2 [12]. Thus, the activity may decrease by storing the catalyst for long time.
The second main drawback associated with the photocatalytic activity of TiO2 is that most of the activated charge carriers will undergo recombination before reaching the surface, preventing interaction with adsorbed molecules. In fact, 90% of the charge carriers may be lost within a nanosecond of their generation leading to low photoactivity of TiO2 [13]. The high recombination rate of photogenerated electron-hole pairs, which controls the photocatalytic efficiency of semiconductors, can be reduced by trapping the electrons with noble metals [14]. The noble metals such as Pt, Ag, and Au, when deposited over TiO2, can act as electron traps, since they have the high Schottky barriers among the metals [15–19].
Our aim is to develop highly competent catalysts, which can prevent the recombination of charge carriers effectively, so that the photocatalysts can act well even by utilizing the UV light from the sun. In the present work, the surface doping of sol gel TiO2 has been done with gold nanoparticles (AuNPs), with an aim to trap the electrons to prevent recombination. The selection of AuNPs as dopant was also based on its property of UV light absorption, causing the transition of 5d electrons to the 6sp band (interband transition) [20, 21]. It is also reported that due to the high photon energy, UV light is able to drive chemical reactions on AuNPs [22]. AuNP supported over zeolite, ZrO2, and SiO2, were found to be effective for the degradation of dye pollutant sulforhodamine-B [22]. The incorporation of nanogold over supports other than TiO2 required high percentage loading of gold for its effective photocatalytic activity [22]. Thus, a combination of AuNP and TiO2 can lead to the formation of a cost effective photocatalyst.
In the present study, nanogold particles were doped over TiO2 catalysts, using chloroauric acid as the gold precursor, by deposition-precipitation method. TiO2 was prepared by sol-gel method. Highly dispersed gold nanoparticles with diameter less than 5 nm were found to be deposited over TiO2. All the TiO2 based catalysts of the present study were found to exist in the anatase phase. The reaction parameters were varied in the degradation of methylorange (MO) for attaining best conditions for photocatalysis.
2. Experimental2.1. Preparation of Titania Support
Titania photocatalysts using titanium (IV) isopropoxide (Sigma Aldrich) as titanium precursor were prepared by sol-gel method with slight modifications from the reported procedure [23]. 0.0628 mol titanium (IV) isopropoxide and 0.8563 mol ethyl alcohol (Hamberg Chemicals), were mixed first. Then a mixture of 0.8563 mol ethyl alcohol, 0.2186 mol glacial acetic acid (R &M Chemicals) and 6.25 mL distilled water was added to the above solution. The resultant solution was stirred to get transparent titania sol. It was then aged for 2 days and dried in an air oven at 80°C. Ground into fine powder and calcination was done at 400°C for 5 h to obtain TiO2 powder.
2.2. Preparation of Nanogold Doped Titania
For the preparation of nanogold, 2.1 × 10−3 M chloroauric acid (Sigma Aldrich) solution was used as the gold precursor, and NaOH (R&M Chemicals) was added to it under stirring so as to adjust the pH of the solution to 8. For nanogold doping over TiO2, required amount of TiO2 powder was added to the freshly prepared nanogold solution where the pH of 8 was kept constant at 70°C, and the solution was stirred well for 2 hours. The mixture was filtered, and the residue was washed with distilled water to remove chloride ions. The nanogold incorporated TiO2 was dried at 80°C and calcined at 200°C for 5 h. The doped systems were designated as n%Au/TiO2, where n indicates the weight percentage of gold taken for doping over TiO2.
2.3. Catalyst Characterization
XRD patterns of the samples were recorded for 2θ between 3 and 80° on a Bruker AXS D8 Advance diffractometer employing a scanning rate of 0.02°/S with Cu Kα radiation (λ = 1.5418 Å). Transmission electron microscopic (TEM) analyses were conducted using ZEISS LIBRA 200 electron microscope. XPS of 1.5%Au/TiO2 sample was recorded with a SPECS spectrometer using nonmonochromatic AlKα source (1486.6 eV) run at 150 W (12 kV and 12.5 mA). Survey scan was obtained with 70 eV pass energy and high resolution scan of Ti 2p, O 1s and Au 4f with 40 eV pass energy. The binding energies reported here were calculated with reference to C 1 s peak at 284.6 eV. Au 4f core level was curve fitted into several components with Gaussian-Lorentzian peaks after subtracting Shirley background. Diffuse reflectance Ultraviolet-visible spectroscopy (UV-vis DRS) of powder catalyst samples was carried out at room temperature using a Varian, Cary 5000 spectrophotometer in the range of 200 to 800 nm. Elemental composition of the prepared samples was determined by using Thermo Electron IRIS INTREPID II XSP DUO Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES).
2.4. Photoactivity Measurements
The efficiency of the nanogold doped TiO2 photocatalysts was examined by the photodegradation of dye pollutants in a Rayonet type Photoreactor (Associate Technica, India) having 16 UV tubes of 8W (HITACHI F8T5 8 WATT Hittach, Ltd., Tokyo, Japan) capacity. In a typical experiment, 50 mL of 10 mg/L of MO was placed in a quartz tube containing 3 g/L of catalyst and was irradiated with UV light under continuous stirring by air flow for 1 h. The above mentioned conditions were used in all experiments unless otherwise mentioned. The MO concentration was analyzed using a Varian, Cary spectrophotometer by absorbance measurements at the wavelength of maximum absorption of MO (464 nm) before and after degradation. The reaction conditions such as catalyst weight (1 to 5 g/L), dye concentration (5 to 20 mg/L), irradiation time (30 to 120 min under sunlight and 15 to 90 min under UV light irradiation), weight percentage of gold over TiO2, and so forth were varied to find out the best condition for maximum photodegradation. The degradation studies were also conducted under different pH. Performance of 2%Au/TiO2 in degrading different dyes in the selected conditions was also evaluated. Activity studies under sunlight were investigated using 1.5%Au/TiO2.
3. Results and Discussion3.1. Catalyst Characterization
XRD patterns of the undoped and AuNP doped samples in Figure 1 showed anatase as the only phase (major peak at 2θ = 25.5°), which is reported as the most photocatalytically active crystalline state of TiO2 [24]. No peaks for gold are found to be present, indicating efficient dispersion of the inserted metal with dimensions lower than 5 nm [25]. TEM images shown in Figure 2 supported the above supposition. Well-dispersed gold nanoparticles, in the range of 2-3 nm diameters, appeared as black spots over the gray-coloured spherical particles of TiO2. Since AuNP over TiO2 is having diameter less than 5 nm, it lies in the size range required for effective use of nanogold in catalysis [26]. The spherical shaped titania particles have diameters in the range of 15–25 nm. Anatase lattice fringes are visible, and the micrograms demonstrate that the particles are connected to each other to form a mesoporous crystalline framework [27].
XRD patterns of the prepared photocatalysts.
TEM image of TiO2 and AuNP loaded TiO2 photocatalysts.
The XPS spectrum of the representative sample, 1.5%Au/TiO2, was measured to elucidate the chemical state of Au and other species in the prepared samples. Figure 3 shows the wide scan spectra of the sample, and the spectra corresponding to Ti 2p, O 1s and Au 4f. From the high resolution spectra, it can be seen that the Ti 2p peaks appeared at binding energies (B.E.) of 458.7 (2p3/2) and 464.4 (2p1/2). The peak at 458.7 corresponds to titanium in pure anatase. Here, the energy splitting between Ti 2p1/2 and Ti 2p3/2 is 5.7 eV, which confirms the existence of titanium as Ti4+ [28]. It is also reported that the position of the Ti 2p3/2 component at 458.7 eV corresponds to the oxidation state of +4 of Ti in titanium dioxide [29, 30]. The O 1s B.E. of the sample is located at 530.0 eV, which is assigned to bulk oxide (O2−) in the TiO2 lattice. Therefore, it can be concluded that no obvious changes on the chemical state of Ti and O were caused by doped and deposited Au.
XPS spectra of 1.5%Au/TiO2: (a) wide scan spectra, (b) high resolution spectra corresponding to Ti 2p, O 1s, and Au 4f.
Au 4f XPS spectrum of 1.5%Au/TiO2 sample exhibited peaks at the B.E. values of 83.6 and 87.1 eV for 4f7/2 and 4f5/2 electrons, corresponding to Au in the metallic state [31]. In addition, peaks arising from Au+1 are observed at 84.8 eV (4f7/2) and 88.6 (4f5/2). It is depicted that 92% of Au exists in Au0 state and 8% exists in its ionic state, Au+. This confirms the formation of nanogold, Au0 on the TiO2 surface. As per the reported data [32, 33], the doublet of Au0 was centered at 84.0 and 87.7 eV. The decrease in the binding energies of Au 4f peaks in the present Au doped TiO2 system may be due to the negative charge of the Au nanoparticles as a result of the charge transfer from the TiO2 substrate as already reported [34]. The formation of negative charge of the Au nanoparticles may be due to the large difference in the work function of Au and TiO2 which facilitates the electron transfer from TiO2 to Au [34]. The negative shift in comparison with bulk gold thus suggests the formation of a strong metal-support interaction [35] over the present catalyst. XPS analysis also confirmed the absence of any contamination from sodium and chlorine species (NaOH and HAuCl4), which were used during the doping process.
Two bands are observed in the UV-visible diffuse reflectance spectra of Au doped TiO2 samples (Figure 4). The intense band with absorption maxima around 320 to 350 nm is associated to the O2−-Ti4+ charge-transfer, corresponding to the electronic excitation from the valence band to the conduction band [36]. In the case of undoped TiO2, this band is found to be highly intense, which may be a result of the presence of greater number of Ti4+ ions and consequently a greater number of Ti4+-O2− bonds [37]. Gold doping decreases the intensity of this band, which can be due to the interaction between Au nanoparticles with the TiO2 support [38]. The metal-support interaction is already suggested from the interpretation of XPS results. A slight red shift of the above band is observed upon gold doping. The shift may be due to the insertion of metal ions into the TiO2 at substitutional sites [39]. XPS analysis revealed the presence of a minor percentage of Au+ in the representative sample, 1.5%Au/TiO2, supporting this possibility. Nanogold doped samples show the presence of a comparatively less intense band with λmax in the region of 540–570 nm. This band can be attributed to the surface plasmon resonance of Au, which arises from the collective oscillations of the free conduction band electrons that are induced by the incident electromagnetic radiation [40, 41].
UV-visible diffuse reflectance spectra of Au doped TiO2 samples.
The elemental analysis results of representative samples, 1%Au/TiO2, 1.5%Au/TiO2, and 2%Au/TiO2, reveals the inserted Au contents as 0.074 wt%, 0.182 wt%, and 0.225 wt%, respectively. Increase in the amount of gold precursor in the preparation showed an increase in the amount of metal incorporated over TiO2. The incorporated amount was less than the amount of gold taken, which may be due to the loss of unbound nanogold while washing the catalysts with distilled water during the preparation.
3.2. Photocatalytic Activity
The activity of the different systems under visible light was investigated, and it was found that the photocatalysts were not active under visible light. But the experiments under UV irradiation were satisfactory in the degradation of MO. The reaction parameters were varied to get best results.
Figure 5 describes the effect of reaction conditions on the performance of the catalyst. Initial steep rise in photodegradation capacity is observed with increase in the amount of catalyst weight, which then attains saturation at a catalyst dosage of 3 g/L. Thus a catalyst weight of 3 g/L (0.15 g) was selected for further studies. The dye concentration is varied, and from the results, it is observed that the catalyst showed 100% degradation of the dye pollutant at low concentrations. The activity decreased from an increased dye concentration of 15 mg/L onwards as seen from the data shown in Figure 5(b). We also varied the pH of the solution, since the dye pollutant effluent from the industry may be of different pH. The catalysts worked well in lower pH values till the natural pH of the solution. Under basic pH, activity is reduced and the percentage dye degradation decreased to 84.9% at a high pH value of 11. Still, the activity is better since the percentage dye degradation is more than 80% as observed in the results shown in Figure 5(c).
Influence of reaction conditions on photodegradation of methylorange over different photocatalysts.
The percentage of gold doping over TiO2 is varied to attain maximum photoactivity, and the dye degradation is monitored. Incorporation of gold increases the activity of TiO2 drastically, which again moves up with increase in the amount of gold. Both 1.5% and 2 wt% AuNP doped systems gave 100% degradation of 50 mL, 10 mg/L MO dye over 3 g/L catalyst for 2 h exposure to UV light. In order to recognize the best Au doping, the time of UV irradiation was changed to 1 h, where 2%Au/TiO2 provided the complete dye degradation. The results given in Figure 5(d) suggest 2%Au/TiO2 as the best photocatalyst of the present investigation.
Reusability of the catalyst is one of the most projected attractions of any heterogeneous catalyzed reaction, but only limited experiments are there on the reusability studies of powder photocatalysts [42, 43]. This may be due to the difficulties in separation of the catalyst powder after pollutant degradation and may also be due to the low reusability of the catalysts. Present catalysts are easily separable from the solution and also well dispersible under stirring. It is simple to detach the catalyst from the cleaned solution either by filtration or by centrifugation. There was no permanent adsorption of dye over the catalyst, and the cleaning merely arises from photodegradation. Regeneration of the best catalyst, 2%Au/TiO2, was done after each reaction, by centrifugation, washing with water, and further treatment at the calcination temperature of the catalyst, that is, at 200°C, for 1 h. The photocatalytic activity of the nanogold doped titania remains intact even up to ten consecutive experiments under the selected reaction conditions (Figure 6). The performance of the 2% Au/TiO2 in the degradation of a number of dye pollutants was also tested where the activity is found to be admirable. The results are given in Table 1.
Photodegradation of aquatic dye pollutants over Au NP doped TiO2.
Dyes
% Degradation
Methylorange
100.00
Crystal violet
98.63
Methylene blue
95.30
Malachite green
100.00
Orange II
99.05
Acid blue
94.69
Reaction conditions: 50 mL of 10 mg/L dye solution, 0.15 g catalyst, 1 h, 2% Au/TiO2.
Reusability data over 2%Au/TiO2 in the degradation of 50 mL of 10 mg/L MO, over 3 g/L catalyst, for 1 h irradiation under UV.
The excellent activity of the present nanogold loaded TiO2 photocatalysts under UV light pinched us to test its ability to harvest the UV present in the sunlight. The photoactivity was also evaluated by the direct use of sunlight that may immediately turn the attention of industries for pollutant treatment. Akbarzadeh et al. had reported vanadium doped TiO2 systems that are effective under sunlight where the catalyst used both UV and visible spectra of the sunlight for photoactivity [44]. The 0.5% vanadium doped TiO2 showed 53.99% degradation of methyleneblue after 1 h irradiation. Present AuNP doped TiO2 displayed very good activity under sunlight where more than 80% of the methylorange dye is degraded within 1 h and degradation reached around 93% by 2 h exposure to sunlight over 1.5%Au/TiO2. The use of UV radiation of sunlight for the photocatalytic degradation is investigated in our experiments. When the reaction is conducted under sunlight using glass tubes instead of quartz tubes, the activity dropped drastically. Glass is opaque to UV light and that may be the reason for decreased activity which suggests the use of UV light for degradation. The degradation data of MO under sunlight over 1.5%Au/TiO2 with time is presented in Figure 7(a). The degradation results under UV lamps are also offered for comparison in Figure 7(b).
(a) Degradation of 10 mg/L MO under sunlight over 3 g/L of 1.5%Au/TiO2. (b) Degradation of 10 mg/L MO under UV irradiation over 3 g/L of 2%Au/TiO2.
3.3. Proposed Mechanism of Photodegradation
The plausible reaction mechanism for the photodegradation of dyes over nanogold doped TiO2 under UV irradiation is suggested here. Upon UV irradiation, the electrons present in the valance band (VB) get promoted to the conduction band (CB) since the band gap of TiO2 lies in the UV region [45–47]. In the CB, the electrons can be further transferred to the adsorbed O2 on the surface of TiO2 to form the superoxide radical anions, O2•- [48, 49]. In addition, in the case of metal nanoparticle doped TiO2, the metal nanoparticles can be considered as an electron sink, where the electrons in the conduction band can migrate to the noble metal surface, thereby preventing the recombination of electron-hole (e−-h+) pairs [40, 45]. Thus the migration of electrons from the interior of the photocatalyst to the metal surface results in increased photoquantum efficiency, which can be the reason for the excellent photoactivity for the present nanogold doped systems even by using low intensity UV present in the sunlight. The transferred electrons in the metal surface facilitate the formation of oxygen superoxide radical anion. In the VB, the holes interact with water molecules, resulting in the formation of hydroxyl radical (•OH) and proton. Protonation of the superoxide anion, O2•-, creates •OOH radicals which leads to the formation of H2O2 and finally •OH radical [50]. These •OH radicals are responsible for the degradation of dye molecules. The presence of •OH radicals for photoactivity is already confirmed in previous reports [50–53]. Thus it can be understood that insertion of AuNP as well as increase in the amount of inserted nanogold particles can increase the photoactivity of TiO2 significantly. Increase in the number of AuNPs over the support can lead to the enhanced migration of electrons from the CB of TiO2 to the Au surfaces which promotes the electron transfer to the adsorbed O2 molecules [54, 55]. This will facilitate the formation of more number of O2•- and finally can lead to the formation of more number of •OH which is responsible for dye degradation. This explains the observed increase in the dye degradation over the present photocatalysts with an increase in the percentage gold doping. The mechanism of photodegradation is schematically represented in Figure 8.
Plausible mechanism of photodegradation of dyes over AuNP doped TiO2.
4. Conclusions
Highly efficient photocatalysts were prepared by nanogold doping over sol-gel TiO2. XRD patterns show the exclusive existence of anatase crystalline phase of TiO2. Majority of the incorporated gold exists in its metallic state, where the particles have diameters less than 5 nm. The strong interaction between the Au and the support, as evident from the characterization of the materials, leads to enhanced photocatalytic activity. The gold nanoparticles act as effective trapping centres to prevent recombination of electron-hole pairs, making the catalysts even active under sunlight for the efficient degradation of pollutants. Another attractiveness of the present photocatalysts lies in their easy separation from the cleaned solution and reusability.
Acknowledgments
The authors acknowledge UKM, Grant number UKM-GUP-NBT-08-26-091, for financial support. SAIF KOCHI, CUSAT, India, is acknowledged for XRD, UV-vis DRS, and ICP-AES measurements. The authors would like to thank Dr. C. Anandan from SED, National Aerospace Laboratories, Bangalore, India, for XPS analysis. Binitha Narayanan thanks University Grants Commission, New Delhi, India, for UGC Research Award.
BickleyR. I.Gonzalez-CarrenoT.LeesJ. S.PalmisanoL.TilleyR. J. D.A structural investigation of titanium dioxide photocatalysts19919211781902-s2.0-44949277711NakataK.FujishimaA.TiO2 photocatalysis: design and applications201213316918910.1016/j.jphotochemrev.2012.06.001FujishimaA.RaoT. N.TrykD. A.Titanium dioxide photocatalysis2000111212-s2.0-0038174714QinH. L.GuG.-B.LiuS.Preparation of nitrogen-doped titania using sol-gel technique and its photocatalytic activity200811223463522-s2.0-5334912988210.1016/j.matchemphys.2008.05.059GandheA. R.FernandesJ. B.A simple method to synthesize N-doped rutile titania with enhanced photocatalytic activity in sunlight20051789295329572-s2.0-2414443596210.1016/j.jssc.2005.06.034ZhangK.OhW. C.Kinetic study of the visible light-induced sonophotocatalytic degradation of MB solution in the presence of Fe/TiO2-MWCNT catalyst2010316158915952-s2.0-7795393191410.5012/bkcs.2010.31.6.1589HattoriA.YamamotoM.TadaH.ItoS.A promoting effect of NH4F addition on the photocatalytic activity of sol-gel TiO2 films199887077082-s2.0-0032357774UmebayashiT.YamakiT.ItohH.AsaiK.Band gap narrowing of titanium dioxide by sulfur doping20028134544562-s2.0-7995601302510.1063/1.1493647KhanS. U. M.Al-ShahryM.InglerW. B.Jr.Efficient photochemical water splitting by a chemically modified n-TiO220022975590224322452-s2.0-003718394610.1126/science.1075035SatoS.Photocatalytic activity of NOx-doped TiO2 in the visible light region19861231-21261282-s2.0-0038606410ZhouP.YuJ.WangY.The new understanding on photocatalytic mechanism of visible-lightresponse N–S codoped anatase TiO2 by first-principles2013142-143455310.1016/j.apcatb.2013.04.063HorikawaT.KatohM.TomidaT.Preparation and characterization of nitrogen-doped mesoporous titania with high specific surface area20081102-33974042-s2.0-3984910342410.1016/j.micromeso.2007.06.048BinithaN. N.YaakobZ.ResmiR.Influence of synthesis methods on zirconium doped titania photocatalysts2010811821872-s2.0-7674911249010.2478/s11532-009-0112-1ZhouM.ZhangJ.ChengB.YuH.Enhancement of visible-light photocatalytic activity of mesoporous Au–TiO2 nanocomposites by surface plasmon resonance201220121053284310.1155/2012/532843KamatP. V.Photochemistry on nonreactive and reactive (semiconductor) surfaces19939312673002-s2.0-10844264497WangC. Y.LiuC. Y.ZhengX.ChenJ.ShenT.The surface chemistry of hybrid nanometer-sized particles. I. photochemical deposition of gold on ultrafine TiO2 particles19981311–32712802-s2.0-003188611810.1016/S0927-7757(97)00086-1SclafaniA.HerrmannJ. M.Influence of metallic silver and of platinum-silver bimetallic deposits on the photocatalytic activity of titania (anatase and rutile) in organic and aqueous media199811321811882-s2.0-0032574016WoldA.Photocatalytic properties of TiO21993532802832-s2.0-0001594423YuJ.XiongJ.ChengB.LiuS.Fabrication and characterization of Ag–TiO2 multiphase nanocomposite thin films with enhanced photocatalytic activity2005603-42112212-s2.0-2584443295010.1016/j.apcatb.2005.03.009LinkS.BurdaC.WangZ. L.El-SayedM. A.Electron dynamics in gold and gold-silver alloy nanoparticles: the influence of a nonequilibrium electron distribution and the size dependence of the electron-phonon relaxation19991113125512642-s2.0-0000000796VoisinC.FattiN. D.ChristofilosD.ValleeF.Ultrafast electron dynamics and optical nonlinearities in metal nanoparticles200110512226422802-s2.0-0035967370ZhuH.ChenX.ZhengZ.KeX.JaatinenE.ZhaoJ.GuoC.XieT.WangD.Mechanism of supported gold nanoparticles as photocatalysts under ultraviolet and visible light irradiation200948752475262-s2.0-7214913200610.1039/b917052aQinH.GuG.LiuS.Preparation of nitrogen-doped titania and its photocatalytic activity20072632542622-s2.0-3434734797610.1016/S1001-0521(07)60211-3BinithaN. N.YaakobZ.ReshmiM. R.SugunanS.AmbiliV. K.ZettyA. A.Preparation and characterization of nano silver-doped mesoporous titania photocatalysts for dye degradation2009147S76S802-s2.0-6924921764310.1016/j.cattod.2009.07.014RiadM.SaadL.MikhailS.Influence of support type on the pore structure and the catalytic activity of Pt–Sn/ alumino-silicate catalysts200822262271HarutaM.TsubotaS.KobayashiT.KageyamaH.GenetM. J.DelmonB.Low-temperature oxidation of CO over gold supported on TiO2, α-Fe2O3, and Co3O4199314411751922-s2.0-3364614017910.1006/jcat.1993.1322BelovaV.BorodinaT.MöhwaldH.ShchukinD. G.The effect of high intensity ultrasound on the loading of Au nanoparticles into titanium dioxide20111813103172-s2.0-7795644660710.1016/j.ultsonch.2010.06.012LuoL.CooperA. T.FanM.Preparation and application of nanoglued binary titania-silica aerogel200916111751822-s2.0-5614908821610.1016/j.jhazmat.2008.03.105László KőrösiSzilvia PappJudit MénesiErzsébet IllésVolker ZöllmerAndré RichardtImre DékányPhotocatalytic activity of silver-modified titanium dioxide at solid-liquid and solid-gas interfaces20083191–3136142
10.1016/j.colsurfa.2007.11.030ZhangF.WolfG. K.WangX.LiuX.Surface properties of silver doped titanium oxide films2001148165702-s2.0-003551713810.1016/S0257-8972(01)01305-6WuY.ZhangJ.XiaoL.ChenF.Preparation and characterization of TiO2 photocatalysts by Fe3+ doping together with Au deposition for the degradation of organic pollutants2009883-45255322-s2.0-6734925720710.1016/j.apcatb.2008.10.008LiuY.-C.JuangL. C.Electrochemical methods for the preparation of gold-coated TiO2 nanoparticles with variable coverages20042016695169552-s2.0-404308344610.1021/la049234cHenryM. C.HsuehC. C.TimkoB. P.FreundM. S.Reaction of pyrrole and chlorauric acid: a new route to composite colloids200114811D155D1622-s2.0-000098258210.1149/1.1405802IoannidesT.VerykiosX. E.Charge transfer in metal catalysts supported on doped TiO2: a theoretical approach based on metal-semiconductor contact theory199616125605692-s2.0-0001187597HuangJ.DaiW. L.LiH.FanK.Au/TiO2 as high efficient catalyst for the selective oxidative cyclization of 1,4-butanediol to γ-butyrolactone2007252169762-s2.0-3554894974110.1016/j.jcat.2007.09.011SilijaP.YaakobZ.YarmoM. A.SugunanS.BinithaN. N.Visible light active anion codoped sol gel titania photocatalyst for pollutant degradation20115922522592-s2.0-8005155202910.1007/s10971-011-2491-yBarakatT.IdakievV.CousinR.ShaoG. S.YuanZ. Y.TabakovaT.SiffertS.Total oxidation of toluene over noble metal based Ce, Fe and Ni dopedtitanium oxides201414613814610.1016/j.apcatb.2013.05.064GluhoiA. C.BogdanchikovaN.NieuwenhuysB. E.Alkali (earth)-doped Au/Al2O3 catalysts for the total oxidation of propene20052321961012-s2.0-1764440206410.1016/j.jcat.2005.02.016CarpO.HuismanC. L.RellerA.Photoinduced reactivity of titanium dioxide2004321-2331772-s2.0-994422277810.1016/j.progsolidstchem.2004.08.001KamatP. V.Photophysical, photochemical and photocatalytic aspects of metal nanoparticles200210632772977442-s2.0-003710474310.1021/jp0209289LiuY. C.JuangL. C.Electrochemical methods for the preparation of gold-coated TiO2 nanoparticles with variable coverages20042016695169552-s2.0-404308344610.1021/la049234cSridewiN.TanL. T.SudeshK.Solar photocatalytic decolorization and detoxification of industrial batik dye wastewater using P(3HB)-TiO2 nanocomposite films20113932652732-s2.0-7995260964310.1002/clen.201000344MarkovićD.JokićB.ŠaponjićZ.PotkonjakB.JovančićP.RadetićM.Photocatalytic degradation of dye C.I. direct blue 78 using TiO2 nanoparticles immobilized on recycled wool-based nonwoven material201341101002100910.1002/clen.201200413AkbarzadehR.UmbarkarS. B.SonawaneR. S.TakleS.DongareM. K.Vanadia-titania thin films for photocatalytic degradation of formaldehyde in sunlight20103741-21031092-s2.0-7404914681110.1016/j.apcata.2009.11.035JoseD.SorensenC. M.RayaluS. S.ShresthaK. M.KlabundeK. J.Au-TiO2 nanocomposites and efficient photocatalytic hydrogen production under UV-visible and visible light illuminations: a comparison of different crystalline forms of TiO2201320131068561410.1155/2013/685614FujishimaA.HashimotoK.WatanabeT.19991stTokyo, JapanTokyo BKCIkedaK.SakaiH.BabaR.HashimotoK.FujishimaA.Photocatalytic reactions involving radical chain reactions using microelectrodes199710114261726202-s2.0-0001226899LinsebiglerA. L.LuG.YatesJ. T.Jr.Photocatalysis on TiO2 surfaces: principles, mechanisms, and selected results19959537357582-s2.0-4544235448KwonB. G.YoonJ.Experimental evidence of the mobility of hydroperoxyl/superoxide anion radicals from the illuminated TiO2 interface into the aqueous phase20093036676702-s2.0-7324913141310.5012/bkcs.2009.30.3.667YuJ.DaiG.XiangQ.JaroniecM.Fabrication and enhanced visible-light photocatalytic activity of carbon self-doped TiO2 sheets with exposed {001} facets2011214104910572-s2.0-7865140877710.1039/c0jm02217aXiangQ.YuJ.WongP. K.Quantitative characterization of hydroxyl radicals produced by various photocatalysts201135711631672-s2.0-7995253567410.1016/j.jcis.2011.01.093YuJ.RanJ.Facile preparation and enhanced photocatalytic H2-production activity of Cu(OH)2 cluster modified TiO2201144136413712-s2.0-7995552992410.1039/c0ee00729cYuJ.DaiG.ChengB.Effect of crystallization methods on morphology and photocatalytic activity of anodized TiO2 nanotube array films20101144519378193852-s2.0-7865040439610.1021/jp106324xYuJ.YueL.LiuS.HuangB.ZhangX.Hydrothermal preparation and photocatalytic activity of mesoporous Au–TiO2 nanocomposite microspheres2009334158642-s2.0-6734919367710.1016/j.jcis.2009.03.034XiangQ.YuJ.ChengB.OngH. C.Microwave-hydrothermal preparation and visible-light photoactivity of plasmonic photocatalyst Ag–TiO2 nanocomposite hollow spheres201056146614742-s2.0-7795291399010.1002/asia.200900695