Most aluminum profiles’ production by deep-drawing and extrusion processes require certain degree of structural homogeneity because of the segregated second-phase particles in the as-cast structure. Rolled texture and directionality in properties often give rise to excessive earring, breakout, and tears. This study investigates the effect of heat treatment (artificial aging) on the anisotropic behavior of AA6063 alloy between rolling direction (0°) through 90° directions. The results show significant reduction in property variability in the aged samples along the rolling direction 0°, and 90° directions compared with the as-cast samples. This gave rise to improved % elongation, impact toughness, and substantial reduction (33.3%) in hardness. These results are capable of achieving huge savings in die conditioning and replacement with improved quality and sale of deep-drawn AA6063 alloy profiles for sustained profitability.
In metal forming, texture gradients often ensued due to nonhomogeneous flow. Texture heterogeneities can also occur in other deformation modes, such as sheet rolling, wire drawing and tube extrusion. Thus, in many industrial forming processes for aluminum, mechanical loading is usually combined with some form of heat treatment such as annealing between deformation steps. This serves the purpose of mitigating substantially strain-hardening phenomenon during deformation. A particular example is the stretching of aluminum parts in a number of stages with intermediate annealing treatments. However, this heating and cooling cycle often results in time wastage and could be minimized.
The cause of work hardening during mechanical working varies in different aluminium alloy compositions.
Hardening of nonheat treatable Al-Mg alloys is due mainly to the presence of solute atoms in solid solution. In heat treatable Al-Mg-Si and Al-Cu alloys, strengthening is determined by precipitates formed during aging treatment. For room-temperature forming, the material behaviour of aluminum sheet is completely determined by work hardening and almost independent of the strain rate [
Previous study showed that profiles extruded from both homogenized and unhomogenized billets did exhibit the same mechanical properties and metallurgical features [
Hence, precipitation-hardened aluminium alloys are commercially important group of materials because their mechanical properties can be modified by heat treatment. However, the imperative of even distribution of the precipitated phases to achieve structural homogeneity is a major challenge. This paper studies the impact of ambient temperature rolling and artificial aging on the normal anisotropy, tensile strength, hardness, and impact resistance of 6063 aluminum alloy.
The composition of AA6063 alloy used for this study is given in Table
Chemical composition of Al 6063 alloy.
Element | Al | Mg | Si | Fe | Mn | Ti | Zn | Ni | Cu | Sn |
---|---|---|---|---|---|---|---|---|---|---|
% Composition | 98.65 | 0.499 | 0.466 | 0.343 | 0.015 | 0.011 | 0.007 | 0.006 | 0.002 | 0.001 |
The cleaned casts were divided into three groups, namely, control samples (CS), cold rolled sample (RS), and cold rolled and precipitation hardened sample (RAS) for further processing.
RS and RAS samples were homogenized in a Carbolite furnace at 515°C for 8 hours, air cooled and cold rolled (at 27.4°C surface temperature) to 451 mm × 163 mm ×10 mm samples in 13 passes (at 34.4°C surface temperature) (Figure
(a) Test pieces cut at different angles to the rolling direction (b) standard test samples (i) tensile, (ii) impact, and (iii) hardness.
RAS test pieces were subjected to solution heat treatment at 515°C for 8 hours and furnace cooled. These solutionized pieces were artificially aged at 190°C for 8 hours and air cooled to room temperature. Standard microstructural test pieces from CS, RS, and RAS were ground using emery paper with grit 220 to 600 microns in succession. The ground surfaces of the pieces were polished using a mixture of Al2O3 and diamond paste before been etched a solution containing 5 grammes of sodium hydroxide (NaOH) dissolved in 100 mL of water, for 20 seconds and dried. The etched surfaces crystals morphology was carried out using a Digital Metallurgical Microscope at ×800 magnification, and the photomicrographs are shown in Figures
There were 21 samples each for tensile, hardness, and impact tests for the three categories of cast samples. A Vickers microhardness tester model “Deco” 2005 with a test load of 100 g and a dwell time of 10 s was used for the test pieces’ hardness determination. Avery Impact Testing Machine (Charpy Tester) model type number 6703 and serial number E67424/4 with a striking velocity of 298.1 J/s was used for impact energy absorption capacity of the test pieces.
In the aged sample, the hardness in the rolling direction is 51.5 HV which is higher than at 15°, 30°, 60°, and 90° directions but lower to that at 45° (56 HV) and 75° (57.1 HV) directions. Hardness at 45° and 75° directions is similar in as-cast sample, but in the rolling direction it is 77.1 HV.
However, the as-cast hardness value declined at 15° (64.5 HV) but increased again at 30° (78.1 HV) and remain almost the same at 45° (76.2 HV), 60° (75.1 HV) and 75° (72.3 HV) respectively. Thus, peak hardness for as-cast sample is attained in the direction perpendicular to rolling direction. The rolled sample has 76.8 HV in the rolling direction and maximum of 91.1 HV in the 90° direction.
The hardness of rolled sample is superior to as-cast sample in all directions except in the rolling direction where both samples have similar and comparable hardness response (Figure
Hardness variations across sample surface.
Impact energy variations across sample surface.
The tensile strength of as-cast sample is maximum (305 MPa) in the rolling direction and 125 MPa minimum at 60° direction. Tensile strength of 270 MPa is obtained in the rolled sample both in the rolling and 90° directions. The tensile strength of the aged sample oscillates between 210 MPa and 180 MPa with peak and minimum strengths at 15° and 60° directions, respectively (Figure
Ultimate tensile stress (UTS) variations across sample surface.
Elongation variations across sample surface.
In the rolling direction, the normal anisotropy of the samples displayed close responses as the values lie between 0.14 and 0.17. The maximum normal anisotropy for as-cast sample is 0.3 at 15° direction, while the sample’s minimum is 0.14 at 45° direction. Normal anisotropy is 0.21 in the 90° direction for rolled sample and 0.03 minimum at 60° direction. The aged sample has maximum normal anisotropy of 0.33 at 30° direction 0.29 in 45° direction (Figure
Normal anisotropy variations across sample surface.
Micrographs of samples (a) as-cast at 0°, (b) rolled at 0°, (c) rolled and precipitation Hardened at 0°, (d) as-cast at 45°, (e) rolled at 45°, (f) rolled and precipitation Hardened at 45°, (g) as-cast at 90°, and (h) rolled at 90° (i) rolled and precipitation hardened at 90°.
In the rolling direction Mg2Si crystals are formed at the grain boundaries in
At 45°, there is significant increase in the nominal volume fraction of Mg2Si crystals which were precipitated in tandem with the
In the as-cast matrix fairly fine crystals of Mg2Si are precipitated side by side with crystals of
However, by aging the cold rolled sample, recrystallization and precipitation of fresh Mg2Si crystals occurred in between crystals of
Nucleation of semicoherent precipitates,
The results of this study have shown that moderate thermal treatment and enough time allowed for recovery ensure redistribution of the Mg2Si precipitates and other intermetallics within the matrix. This phenomenon is the precursor for the improved formability, better fracture toughness, and significant reduction in hardness coupled with minimal anisotropy.
The authors are grateful to the Management and Staff of Nigerian Aluminum Extrusion (NIGALEX) Company, Oshodi, Lagos Nigeria for the provision of 6063 aluminum alloy used in this study.