JAM Journal of Applied Mathematics 1687-0042 1110-757X Hindawi Publishing Corporation 134124 10.1155/2013/134124 134124 Research Article Pile-Reinforcement Behavior of Cohesive Soil Slopes: Numerical Modeling and Centrifuge Testing Wang Liping http://orcid.org/0000-0003-4074-9270 Zhang Ga Liang Fayun State Key Laboratory of Hydroscience and Engineering Tsinghua University Beijing 100084 China tsinghua.edu.cn 2013 10 9 2013 2013 06 06 2013 29 07 2013 2013 Copyright © 2013 Liping Wang and Ga Zhang. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Centrifuge model tests were conducted on pile-reinforced and unreinforced cohesive soil slopes to investigate the fundamental behavior and reinforcement mechanism. A finite element analysis model was established and confirmed to be effective in capturing the primary behavior of pile-reinforced slopes by comparing its predictions with experimental results. Thus, a comprehensive understanding of the stress-deformation response was obtained by combining the numerical and physical simulations. The response of pile-reinforced slope was indicated to be significantly affected by pile spacing, pile location, restriction style of pile end, and inclination of slope. The piles have a significant effect on the behavior of reinforced slope, and the influencing area was described using a continuous surface, denoted as W-surface. The reinforcement mechanism was described using two basic concepts, compression effect and shear effect, respectively, referring to the piles increasing the compression strain and decreasing the shear strain of the slope in comparison with the unreinforced slope. The pile-soil interaction induces significant compression effect in the inner zone near the piles; this effect is transferred to the upper part of the slope, with the shear effect becoming prominent to prevent possible sliding of unreinforced slope.

1. Introduction

Landslides are one of the severest geologic hazards around the world, the prevention of which is of great interest to engineers and researchers. The stabilizing pile, an important reinforcement structure, has been widely used to support unstable slopes in the last few decades . Many methods have been proposed to form a good basis for proper design of pile-reinforced slopes [4, 5]; however, there are a few important issues to be clarified for the application of such piles in slope engineering. Therefore, systematical investigations are required on the behavior and reinforcement mechanism of pile-reinforced slopes.

The behavior of pile-reinforced slope can be investigated by using a diverse range of research approaches, which can be generally divided into three categories: field observations, model tests, and numerical analyses. Field observation is an essential approach to obtain first-hand data of reinforced slopes. For example, long-term monitoring was used to analyze the bending moments and displacements of the piles that were employed for a railway embankment . Nevertheless, boundary conditions or loading conditions cannot be easily changed in a field test, which restricts such an approach to the study of the reinforcement mechanism.

Model tests offer a powerful approach to investigate the behavior and failure mechanism of a reinforced slope by efficiently considering various factors. A series of 1 g model tests were used to investigate the behavior of a pile-stabilized sandy slope [6, 7]. The centrifuge model tests play an important role in such a category because they provide an accurate simulation of the gravity stress field and the gravity-related deformation process. Therefore, centrifuge modeling has been widely used to study reinforced slopes with different reinforcement structures, including piles, geomembranes, geotextiles, and soil nails . The measurement was finite in the model tests due to the small size of the model and the limitation of measurement technology; for example, the stress state of the slope cannot be measured with sufficient accuracy.

Numerical analysis can yield comprehensive information about the response of the slope; thus, a few different types of numerical methods were developed or used to study the reinforced slopes, such as the limit equilibrium method [14, 15], limit analysis , the finite-element method , and other rigorous or simplified methods . For example, Won et al. compared the predictions by limit equilibrium analysis and three-dimensional numerical analysis involving a shear strength reduction technique for a slope-pile system . A three-dimensional numerical analysis was used to investigate the influence of sleeving on the pile performance in a sloping ground [20, 21]. The FLAC3D program was used to analyze the response of piles in an embankment slope with a translational failure mode, and the results showed that the pile-soil relative stiffness has a significant influence upon the piles’ failure mode . Except for the algorithm, the effectiveness of numerical analysis of reinforced slope is also significantly affected by several aspects, such as the soil model, the soil-structure interface model, and their parameters, which should be acknowledged not to be sufficiently reliable due to the complexity of this problem.

Most previous investigations of the pile-reinforced slope focused on the response of the slope and piles as well as on the influence factors; from those, a few useful conclusions have been achieved. However, the response of the pile-reinforced slope under various types of load applications has not been illustrated in a fully comprehensive view. Moreover, the stabilizing mechanism—for example, why the avoidance of failure is induced by the piles—has not yet been adequately discovered. In other words, further study is needed to clarify how the local pile-soil interaction affects the deformation field of the entire slope and, therefore, increases the stability level. In addition, the deformation trends and main influence factors of the behavior of pile-reinforced slopes have not been fully discovered.

Based on the understanding of the main features of the numerical methods and model tests, an effective approach may be to combine both of the above methods to acquire a comprehensive description of the pile-reinforced slopes. Therefore, the observations from the model tests can be supplemented by a numerical method that has been verified by the model tests. The objective of this paper is to conduct such an attempt for the purpose of reinforcement mechanism analysis of pile-reinforced slope, including (1) to conduct centrifuge model tests of a cohesive soil slope using stabilizing piles, in comparison with the unreinforced slope; (2) to present a numerical scheme of the pile-reinforced slope and to confirm its effectiveness by simulating the centrifuge tests; (3) to analyze the behavior of the reinforced slope by using the test observations and numerical analysis; (4) to describe the reinforcement mechanism; and (5) to discuss the main factors that influence the behavior of reinforced slopes.

2. Centrifuge Model Tests

The centrifuge model tests were conducted using the 50 g ton geotechnical centrifuge at Tsinghua University.

2.1. Model

The soil of the slope model was retrieved directly from the soil mountain of the Beijing Olympic Forest Park. The average grain size of the soil is 0.03 mm, and the plastic limit and liquid limit are 5% and 18%, respectively.

Figure 1 shows the photographic and schematic views of the model slope, reinforced using stabilizing piles. The unreinforced slope is identical except for removal of the piles. The model container for the tests, made of aluminum alloy, is 50 cm long, 20 cm wide, and 35 cm high. A transparent Lucite window was installed in one container side to observe the deformation process of the soil.

Schematic view of the model of reinforced slope (unit: cm).

Photograph

Elevation view

Vertical view

The soil was compacted into the container by a 6-cm-thickness layer, with a dry density and water content of 1.4 g/cm3 and 16%, respectively. The slope was obtained by removing the redundant soil, with an inclination of 1.5 : 1 and height of 25 cm. A 6 cm high horizontal soil layer under the slope was set to diminish the influence of the bottom container. In addition, silicone oil was painted on both sides of the container to decrease the friction on the slope.

A hollow square pipe, made of steel with an elastic modulus of 210 GPa, was used to simulate the stabilizing pile of the reinforced slope. The pipe was 1.4 cm along the side length of the section, with a wall thickness of 1.5 mm. This is equivalent to a prototype pile with a side length of 0.7 m at 50 g-level. These piles were inserted in the slope, without special fixation, at a single row 10 cm apart and 6 cm far away from the slope toe. Half-section piles were used near both container sides to approximate the plane-strain condition (Figure 1(c)).

2.2. Measurements

An image-record and displacement measurement system was used to record the images of soil during the centrifuge tests , which are used to determine the displacement history of an arbitrary point of soil, without disturbing the soil itself, by an image-correlation-analysis algorithm . The effectiveness of this measurement system was realized by embedding white particles laterally in the soil (Figure 1(a)). The measurement accuracy can reach 0.02 mm based on the model dimension for the centrifuge tests in this paper. In addition, a few patterns with significant grey difference were affixed onto the pile to obtain displacement history of the pile on the basis of image analysis. The area within the dotted line was used for displacement measurements owing to the requirement of the measurement system (Figure 1(b)); the main deformation zone can be covered. Cartesian coordinates were established with the origin as the intersection between the slope bottom and inner sidewall of the pile; positive directions were specified (Figures 1(b) and 1(c)).

Four pairs of strain gauges were attached to the inner walls of the middle pile to measure the strain distribution along the shaft (Figure 1(b)). They can be used to derive the bending moment and axial load of the pile.

2.3. Test Procedure

The model slope was installed on the centrifuge machine, and increasing centrifugal acceleration was applied at steps of 5 g. Each acceleration step was maintained for several minutes until the deformation of the slope became stable. This process was terminated at 50 g-level when the unreinforced slope exhibited significant failure.

2.4. Observations

It should be noted that all of the results are based on the model dimension in this paper. Figure 2 shows the horizontal displacement distribution of the pile-reinforced and unreinforced slopes at 50 g-level; the borders in the figures were designated as the dotted area in Figure 1(b), but these do not correspond to the actual slope borders. It can be seen that a significant landslide occurred in the unreinforced slope when the centrifuge acceleration reached 50 g (Figure 2(a)): there was significant concentration of deformation so that the slide body can be easily distinguished from the base body via the contour lines. On the other hand, the reinforced slope only exhibited significant deformation due to the increase of centrifugal acceleration; a landslide was avoided at 50 g-level (Figure 2(b)). This indicated that the piles significantly increased the stability level of the slope. Moreover, the deformation of the reinforced slope was significantly smaller than that of the unreinforced slope, demonstrating that the piles had a significant effect on the deformation of the slope.

Horizontal displacement contours of slopes at 50 g-level (unit: mm).

Unreinforced slope at failure state

Pile-reinforced slope

3. Numerical Analysis 3.1. Analysis Model

A three-dimensional finite element method was used to simulate the pile-reinforced slope under the condition of the centrifuge model test based on geotechnical stress-strain FEM software, termed TOSS3D, that has been widely used for embankments in China . A new iterative routine was developed to simulate the successive increase of centrifugal acceleration in the software. The explicit increment scheme was used in the nonlinear static FE analysis. A substep was divided into several subincrements to simulate the nonlinear loading. An iterative algorithm was employed to obtain the stress-strain states of the slope within a subincrement, with a trial algorithm used to judge loading states of the geomaterials and contact states of the interface.

A three-dimensional FE mesh was established with accurate simulation of the slope model for centrifuge tests (Figure 3). The soil was described using hexahedron elements with eight nodes. The soil was described using an elastoplasticity model that can reasonably capture the dilatancy behavior of the soil . The model parameters were determined from triaxial compression tests and adjusted slightly in the numerical analysis for a better fit to the test observations. The parameters and their values are listed in Table 1 and their definitions could be referred to . It should be noted that the cohesion strength parameter, c, was a bit greater than the empirical. This may be partially because the boundary effect on the model slope in the centrifuge model tests was considered by the strength parameters of the soil. The interface elements were set between the pile and neighboring soil and between the container sides and neighboring soil. The interface was described using an elastoplasticity damage model, which provides a unified description of monotonic and cyclic behavior, including volumetric behavior . This model was used for many soil-structure systems, such as high concrete-faced rockfill dams . The model parameters were determined by a series of shear tests under constant normal stress conditions. The parameters and their values are listed in Table 2 and their definitions could be referred to . The pile was described using a linear elastic model, with elastic modulus of 210 GPa and Poisson’s ratio of 0.3. A soft element set on the pile end to realize the movement of pile. Moreover, another case, with the pile located in the upper slope, as shown in Figure 1(b), was also considered in the mesh. The boundaries of the model slope were all fixed (Figure 3). The mesh was finally obtained according to the symmetry of this problem, involving 8448 nodes and 7140 elements in total.

Model parameters of the elastoplasticity model for soil.

c ( kPa ) ϕ 0 (°) R f K n G F D
50 35 0.7 92 0.15 0.05 0.15 1.5

EPDI model parameters of the interface.

ε vd,ir,ult α β φ 0 (°) G 0 n 0 μ 0 m 0 k 0 m k 0 C e C 0
0.15 500 1.0 33 30 0.5 300 0.3 0 0.1 0.005 0.005

Mesh and boundary of the slope for numerical analysis.

Elevation view

Vertical view

3.2. Verification

The numerical predictions of displacement response of the reinforced slope were compared with the measurements of the centrifuge model test to verify the effectiveness of the numerical analysis.

Figure 4 shows a comparison of test results and numerical predictions of the contours of displacement of the reinforced slope at 50 g-level. It can be seen that the predicted curve showed a good fit to the test result; this demonstrates that the numerical method provides a reasonable description of the overall performance of the slope. Close comparisons of displacement distribution between the test results and numerical predictions were made on several vertical sections (Figure 5). The horizontal and vertical displacements exhibited the maximum at the middle and top of the slope, respectively. These comparisons showed that the numerical prediction curves were in satisfactory agreement with the test results at different locations. In addition, the vertical displacement histories of a typical point of the slope indicated that the vertical displacement increased with increasing centrifugal acceleration (Figure 6), and the numerical prediction showed a good fit to the test observation.

Displacement distribution comparison of numerical analysis and test results (unit: mm).

Vertical displacement

Horizontal displacement

Displacement distribution comparison of numerical analysis and test results on different vertical sections. u: horizontal displacement; v: vertical displacement; D: pile diameter.

y = - 10.5 D

y = - 7 D , passing by slope shoulder

y = - 3 D

Vertical displacement history of a typical point by numerical analysis and test results. v: vertical displacement; g: g-level.

The response of the pile was also used for the comparison of numerical analysis and test results (Figure 7); a satisfactory fit can be found. It should be noted that we used the difference between the vertical strains obtained from the strain gauges on the left and right sides of the pile to consider the bending behavior (Figure 7(b)); this difference exhibited the maximum at the middle part.

Response of the pile by numerical analysis and test results. u: horizontal displacement of pile top; Δε: vertical strain difference between right and left sides of pile.

Horizontal displacement of pile top

Vertical strain distribution

According to the comparison results, it can be concluded that the numerical analysis is effective in capturing the primary behavior of a pile-reinforced slope. The numerical results can be further used to analyze the stress response of the reinforced slope, which is important for understanding the reinforcement behavior but difficult to be measured in the centrifuge model tests. Thus, a comprehensive stress-deformation response can be obtained by combining the numerical and physical simulations.

4. Stress-Deformation Behavior

The numerical results have shown that the stress-displacement response of the reinforced slope is approximated for different sections, whether the piles pass through or not if the pile space is not large, as for most practical cases. Therefore, the behavior of the pile-reinforced slope was analyzed based mainly on the stress-displacement distribution of the lateral side of the slope that the pile passed through, so that the measurement results of the centrifuge model test can be combined with the predictions of numerical analysis.

The stress distribution of the slope was illustrated using numerical analysis at 50 g-level (Figure 8); there was significant stress concentration near the piles. This demonstrated that the piles had a significant effect on the stress state of the neighboring slope, as did the displacement measured by the tests (Figure 2). Figure 9 shows the stress histories of a typical point on the slope. The magnitude of stress increased with increasing centrifugal acceleration; similar rules can be found in the displacement histories (Figure 6). It can be concluded that the stress-deformation response at 50 g-level can be used as a representative time for further analysis.

Stress distribution of the slope at 50 g-level by numerical analysis (unit: kPa).

Horizontal stress

Vertical stress

Shear stress

Stress history of a typical point by numerical analysis. g: g-level.

4.1. Significant Influence Surface

The piles have a more significant influence on the horizontal displacement of the slope than on the vertical displacement, according to the comparison of reinforced and unreinforced slopes. Thus, the distributions of horizontal displacement at horizontal lines of five altitudes were carefully analyzed by comparing the reinforced and unreinforced slopes, covering the overall slope from top to bottom (Figure 10).

Horizontal displacement distributions on horizontal sections at 50 g-level by test observation. u: horizontal displacement; D: pile diameter.

A close examination of displacement distribution at a horizontal line, z = 7.1 cm, showed a significant difference between the reinforced and unreinforced slopes (Figure 10(d)). For the pile-reinforced slope, an evident inflection occurred near the pile. On the left side of the inflection, the horizontal displacement increased significantly from the inner slope area to the piles, whereas this rate of increase became relatively small on the right side. On the other hand, for the unreinforced slope, the horizontal displacement increased from the inner slope at an approximately constant rate near the piles. It can be concluded that the piles significantly changed the displacement distribution of the slope at a certain area near the piles, and this inflection can be regarded as a boundary point to indicate that the piles significantly affected the deformation.

The inflections can be found in the displacement distribution curves of the reinforced slope at all altitudes (Figure 10), including the area above the piles (Figures 10(a)–10(c)). Therefore, a continuous surface was obtained by connecting these inflections using a curve, as shown in Figure 10 by the dotted line, denoted as the W-surface in this paper. The horizontal displacement of the pile-reinforced slope exhibited different distribution rules on different sides of the W-surface.

Similar to the horizontal displacement, the horizontal stress can also be used to reflect the effect of the piles on the slope. Figure 11 shows the horizontal stress distributions on horizontal lines at two typical altitudes, located near and above the piles, with the position of the W-surface being determined from the displacement distribution. It can be seen that the stress distribution curve exhibited a significant change near the W-surface. This demonstrated that the W-surface outlines the area where the piles have a significant effect on the slope, including the displacement and stress response. Thus, the W-surface can be used as an important index to describe the influence of piles on stress-deformation behavior of the reinforced slope.

Stress distribution on a horizontal line by numerical analysis.

z = 3.5 cm

z = 16.5 cm

4.2. Division of Zones

According to the W-surface, the reinforced slope behind the piles can be divided into two zones: one is where the slope is significantly affected by the piles, while the other is where the slope is insignificantly affected. The former was further examined by using the horizontal stress distribution of the slope at different vertical sections (Figure 12). The horizontal stress decreased with increasing altitude from the slope bottom; however, there was a significant inflection in the upper part of the slope. From this inflection, the change trend of the stress noticeably altered. It can be concluded that the stress states of the slope were significantly different on the different sides of the inflection, and the reason can be attributed to the effect of the piles.

Stress distributions on different vertical sections at 50 g-level by numerical analysis.

Thus, another continuous surface was yielded by connecting these inflections using a curve, as the dotted line showed in Figure 12. This surface, denoted as the L-surface in this paper, indicates the boundary where the effect of the piles exhibited different features on different sides. Accordingly, the slope can be divided into three zones behind the piles according to these two surfaces (Figure 13).

Division of zones with different features. D: pile diameter.

The stress-deformation behavior exhibited different features in different zones. Zone A is the area at the left side of the W-surface, far from the piles. Thus, the piles had a small effect on this zone. For example, the horizontal displacement of the reinforced slope showed a similar distribution to the unreinforced slope in zone A. Zone B is above the L-surface and has a free surface. The change of deformation of the slope became flat in this zone; this demonstrated that the piles significantly restricted the deformation. Zone C is at the right side of the W-surface and directly contacts the piles. The piles significantly reduced the horizontal displacement of the soil in this zone; thus, the displacement distribution showed a flat curve. Moreover, the horizontal stress exhibited a significant change with increasing distance from the piles. This demonstrated that the piles induced significant compression effect in this zone.

5. Reinforcement Mechanism

The strain of a soil element within the slope was introduced to analyze the pile-reinforcement mechanism of the slope by comparing the reinforced and unreinforced slopes. This strain can be determined using the measured displacement of the centrifuge model tests because the measurement may be more reliable than the numerical result, especially at the failure state of the unreinforced slope. A two-dimensional, four-node square isoparametric element, 1 cm long, was used for strain analysis. The strain at the center was thought to be the one of this element that was assumed to be uniform within the element.

The deformation of soil can be divided into two independent components owing to shear and compression applications. This implies that shear and compression play different roles in the deformation and failure of a slope. For example, the formation of a slip surface may significantly depend on the increase in shear strain, whereas a tensional crack, which commonly occurs at the top of a slope, is induced mainly by a decrease in compression strain. It can be concluded that the piles significantly changed the strain state of the slope and thus increased the stability level of the slope. Therefore, the pile-reinforcement mechanism can be analyzed using the effects of the piles on the shear and compression strains.

The deformation due to shear was indicated by the slope-direction shear strain. The horizontal compression strain was used to indicate the deformation due to compression. Figure 14 shows the strain histories of typical elements in the three zones (positions are shown in Figure 13); the elements of the unreinforced slope, corresponding to those in the reinforced slope, are also presented for comparison. It should be noted that the horizontal compression strains of these elements were all negative, indicating dilation in the horizontal direction.

Strain history of typical elements of different zones by test observation. γ: slope-direction shear strain; εx: horizontal compression strain; g: g-level.

Zone A

Zone B

Zone C

In zone B, the shear strain of a typical element in the unreinforced slope increased rapidly with increasing centrifugal acceleration (Figure 14(b)). This strain reached a significant magnitude at 50 g-level when the landslide, just across this element, occurred. However, the shear strain increased at a smaller rate and reached a lower level far from failure if the piles were used. Thus, a basic concept, shear effect, was introduced to describe that shear strain was decreased due to the effect of the piles. In other words, a significant shear effect of piles in zone B arrested the formation of a slip surface. Accordingly, the horizontal compression strain increased due to the piles, which was described using another basic concept, compression effect. There was also significant compression effect of piles in zone B; however, it can be concluded that the shear effect was primary.

The history of the compression strain showed that this strain in the reinforced slope was significantly larger than that of the unreinforced one; this demonstrated that there was significant compression effect of piles in zone C (Figure 14(c)). Closer examination showed that the compression effect was more significant than the shear effect, though the shear effect of the piles was also distinct.

The compression and shear strains both exhibited minor differences in zone A for the reinforced and unreinforced slopes (Figure 14(a)); this indicated that both the shear effect and compression effect were negligible in this zone.

Figure 15 shows the earth pressure on the inner side of the pile, obtained by numerical analysis. The earth pressure decreased with increasing altitude, similar to a distribution of earth pressure for a retaining wall. Combined with the strain analysis results at the overall slope level, the reinforcement mechanism can be demonstrated using the shear effect and compression effect of piles, which were of different levels in different zones, as follows: the pile and neighboring soil exhibited a significant interaction due to loading. This interaction was transferred to the adjacent zone and induced a significant compression effect (zone C). This compression effect transferred upwards and caused a prominent shear effect (zone B), arresting the possible sliding and increasing the stability level of the slope.

Earth pressure on the pile by numerical analysis. p: earth pressure.

6. Influence Factors

The numerical analysis was used to compute different cases to discuss the influence factors of the behavior of pile-reinforced slopes by altering several factors based on the centrifuge test condition, including pile spacing, pile location, restriction style of pile end, and inclination of slope. According to previous analysis, the horizontal displacement of the lateral side of the slope that the piles pass across is used as the characteristic index to illustrate the effect of these factors.

6.1. Pile Spacing

The pile spacing was reduced to 3D (pile diameter) from approximately 7D of the test condition. Figure 16 compares the horizontal displacements according to the different pile spacings, both obtained from numerical analysis, to discuss the influence rules. The horizontal displacement of the slope exhibited a small decrease when the pile spacing was reduced; such a difference decreased with increasing distance from the piles. The fundamental rules of horizontal displacement were consistent for different pile spacings.

Influence of pile spacing by numerical analysis. D: pile diameter; u: horizontal displacement.

y = - 0.8 D

y = - 7 D , passing by slope shoulder

6.2. Location of Pile

The piles were moved upwards several centimeters in the comparison case, as described using the dashed line in Figure 1(b). The horizontal displacements according to new and original locations of piles were obtained from numerical analysis (Figure 17). The horizontal displacement of the slope exhibited a significant decrease near the piles if the pile was located at an upper position, which may be partly attributed to the new location of piles being farther from the free surface of the slope. The difference decreased with increasing distance from the slope surface and can be ignored at the section passing by the slope shoulder (Figure 17(c)). It can be derived that the distributions of horizontal displacement of the pile-reinforced slope were consistent for different pile locations.

Influence of positions of the pile by numerical analysis. D: pile diameter; u: horizontal displacement.

0.8D from pile

3D from pile

y = - 7 D , passing by slope shoulder

6.3. Restriction Style of Pile End

The pile ends were all fixed on the container to prevent the relative movement between the piles and the container bottom, different from the test condition that the piles may move along the container bottom. Figure 18 compares the horizontal displacements according to the different restriction styles, both obtained from numerical analysis. The horizontal displacement of the slope significantly decreased, especially near the piles, when the pile ends were fixed. Overall, the fundamental rules of horizontal displacement of pile-reinforced slope can be found to be consistent regardless whether the restriction style of pile end was altered.

Influence of fixing styles of the pile end by numerical analysis. D: pile diameter; u: horizontal displacement.

y = - 0.8 D

y = - 3 D

y = - 7 D , passing by slope shoulder

6.4. Inclination of Slope

The inclination of the slope was changed to 1 : 1 from the original 1.5 : 1 in the test condition, and the relative location of piles was maintained as in the original scheme. The horizontal displacements according to the different inclinations of slopes were yielded from numerical analysis (Figure 19). The horizontal displacement of the slope exhibited an evident decrease due to the decrease of inclination of slope. However, the distribution rules of horizontal displacement were consistent for the different inclinations of slope.

Influence of inclination of the slope by numerical analysis. D: pile diameter; u: horizontal displacement.

3D from pile

y = - 7 D , passing by slope shoulder

6.5. Summary

Based on the numerical analysis, it can be concluded that the behavior of the pile-reinforced slopes was similar for the different factors considered in this paper. As discussed in above texts, the two boundary surfaces, W-surface and L-surface, can be used as important indicators of the behavior of reinforced slope. Therefore, these surfaces were summarized corresponding to different factors according to the results from numerical analysis (Figure 20). It can be seen that both of the surfaces can be described using a definite format, though their positions and curvatures were affected by different factors. Thus, it is believed that the fundamental rules and reinforcement mechanism, derived in this paper, may be suitable for most practical pile-reinforced slopes.

W-surfaces and L-surfaces considering different factors. L: pile spacing; D: pile diameter.

Test, L=3D, pile end fixed

Pile location changed

Slope inclination changed to 1 : 1

7. Conclusions

The pile-reinforcement behavior of cohesive soil slope was investigated using numerical analysis and centrifuge model tests. The behavior and reinforcement mechanism of the pile-reinforced slope were obtained by considering different influence factors. The main conclusions are as follows.

The piles arrested a landslide that occurred in an unreinforced slope, thus, significantly increasing the stability level of the slope.

A numerical model was established and confirmed to be effective in capturing primary behavior of the pile-reinforced slope. Thus, a comprehensive understanding of stress-deformation response can be achieved by combining the numerical and physical simulations.

The piles have a significant effect on the behavior of reinforced slope; the boundary of the influenced area can be described using a continuous surface.

The pile-reinforcement mechanism can be described using two basic concepts: compression effect and shear effect, which, respectively, refer to the piles increasing the compression strain and decreasing the shear strain in comparison with unreinforced slope. The pile-soil interaction induces significant compression effect in the inner zone near the piles; this effect is transferred to the upper part of the slope, with the shear effect becoming prominent. As a result, possible sliding is prevented; the stability level of the slope is accordingly increased.

The response of pile-reinforced slope was significantly affected by several factors such as pile spacing, pile location, restriction style of pile end, and inclination of slope; however, the behavior and reinforcement mechanism are consistent for the different factors considered in this paper.

Acknowledgments

The study is supported by National Natural Science Foundation of China (nos. 51129902, 50979045) and the State Key Laboratory of Hydroscience and Engineering (no. 2013-KY-5).

Rogers C. D. F. Glendinning S. Improvement of clay soils in situ using lime piles in the UK Engineering Geology 1997 47 3 243 257 2-s2.0-0031554742 Smethurst J. A. Powrie W. Monitoring and analysis of the bending behaviour of discrete piles used to stabilise a railway embankment Geotechnique 2007 57 8 663 677 2-s2.0-35348942398 10.1680/geot.2007.57.8.663 Kimura M. Inazumi S. Too J. K. A. Isobe K. Mitsuda Y. Nishiyama Y. Development and application of H-joint steel pipe sheet piles in construction of foundations for structures Soils and Foundations 2007 47 2 237 251 2-s2.0-41149094258 Ito T. Matsui T. Methods to estimate lateral force acting on stabilizing piles Soils and Foundations 1975 15 4 43 59 2-s2.0-0016644650 Poulos H. G. Design of reinforcing piles to increase slope stability Canadian Geotechnical Journal 1995 32 5 808 818 2-s2.0-0029415866 El Sawwaf M. A. Strip footing behavior on pile and sheet pile-stabilized sand slope Journal of Geotechnical and Geoenvironmental Engineering 2005 131 6 705 715 2-s2.0-19844376184 10.1061/(ASCE)1090-0241(2005)131:6(705) Thompson M. J. White D. J. Design of slope reinforcement with small-diameter piles Advances in Earth Structures: Research to Practice 2006 GSP 151 ASCE 67 73 10.1061/40863(195)3 Bouafia A. Bouguerra A. Centrifuge testing of the behaviour of a horizontally loaded flexible pile near to a slope Canadian Geotechnical Journal 1995 32 2 324 335 2-s2.0-0029543438 Porbaha A. Goodings D. J. Centrifuge modeling of geotextile-reinforced steep clay slopes Canadian Geotechnical Journal 1996 33 5 696 704 2-s2.0-0030267990 Zornberg J. G. Sitar N. Mitchell J. K. Performance of geosynthetic reinforced slopes at failure Journal of Geotechnical and Geoenvironmental Engineering 1998 124 8 670 683 2-s2.0-0032144147 10.1061/(ASCE)1090-0241(1998)124:8(670) Thusyanthan N. I. Madabhushi S. P. G. Singh S. Tension in geomembranes on landfill slopes under static and earthquake loading-Centrifuge study Geotextiles and Geomembranes 2007 25 2 78 95 2-s2.0-33846591400 10.1016/j.geotexmem.2006.07.002 Wang L. Zhang G. Zhang J.-M. Nail reinforcement mechanism of cohesive soil slopes under earthquake conditions Soils and Foundations 2010 50 4 459 469 2-s2.0-79954860595 10.3208/sandf.50.459 Wang L. P. Zhang G. Centrifuge model test study on pile reinforcement behavior of cohesive soil slopes under earthquake conditions Landslides 2013 10.1007/s10346-013-0388-2 Yamagami T. Jiang -C J. Ueno K. A limit equilibrium stability analysis of slopes with stabilizing piles Advances in Earth Structures: Research to Practice 2000 GSP 101 ASCE 343 354 10.1061/40512(289)25 Zhang G. Wang L. Stability analysis of strain-softening slope reinforced with stabilizing piles Journal of Geotechnical and Geoenvironmental Engineering 2010 136 11 1578 1582 2-s2.0-77957906151 10.1061/(ASCE)GT.1943-5606.0000368 Ausilio E. Conte E. Dente G. Stability analysis of slopes reinforced with piles Computers and Geotechnics 2001 28 8 591 611 2-s2.0-0034875979 10.1016/S0266-352X(01)00013-1 Cai F. Ugai K. Numerical analysis of the stability of a slope reinforced with piles Soils and Foundations 2000 40 1 73 84 2-s2.0-0003153783 Jeong S. Kim B. Won J. Lee J. Uncoupled analysis of stabilizing piles in weathered slopes Computers and Geotechnics 2003 30 8 671 682 2-s2.0-0242551832 10.1016/j.compgeo.2003.07.002 Won J. You K. Jeong S. Kim S. Coupled effects in stability analysis of pile-slope systems Computers and Geotechnics 2005 32 4 304 315 2-s2.0-20444402253 10.1016/j.compgeo.2005.02.006 Ng C. W. W. Zhang L. M. Three-dimensional analysis of performance of laterally loaded sleeved piles in sloping ground Journal of Geotechnical and Geoenvironmental Engineering 2001 127 6 499 509 2-s2.0-0035367485 10.1061/(ASCE)1090-0241(2001)127:6(499) Ng C. W. W. Zhang L. M. Ho K. K. S. Influence of laterally loaded sleeved piles and pile groups on slope stability Canadian Geotechnical Journal 2001 38 3 553 566 2-s2.0-0034742184 10.1139/cgj-38-3-553 Martin G. R. Chen C.-Y. Response of piles due to lateral slope movement Computers and Structures 2005 83 8-9 588 598 2-s2.0-13844266800 10.1016/j.compstruc.2004.11.006 Zhang G. Hu Y. Zhang J.-M. New image analysis-based displacement-measurement system for geotechnical centrifuge modeling tests Measurement 2009 42 1 87 96 2-s2.0-56249147463 10.1016/j.measurement.2008.04.002 Zhang G. Liang D. Zhang J.-M. Image analysis measurement of soil particle movement during a soil-structure interface test Computers and Geotechnics 2006 33 4-5 248 259 2-s2.0-33747768202 10.1016/j.compgeo.2006.05.003 Zhang G. Zhang J.-M. Yu Y. Modeling of gravelly soil with multiple lithologic components and its application Soils and Foundations 2007 47 4 799 810 2-s2.0-64849101200 Zhang G. Zhang J.-M. Unified modeling of monotonic and cyclic behavior of interface between structure and gravelly soil Soils and Foundations 2008 48 2 231 245 2-s2.0-64849112581 Zhang G. Zhang J.-M. Numerical modeling of soil-structure interface of a concrete-faced rockfill dam Computers and Geotechnics 2009 36 5 762 772 2-s2.0-64849100535 10.1016/j.compgeo.2009.01.002