A Localized Surface Plasmon Resonance Sensing Method for Simultaneous Determination of Atenolol and Amiloride in Pharmaceutical Dosage Forms and Urine Samples

This contribution describes a simple, fast, and sensitive application of localized surface plasmon resonance effect of silver nanoparticles for simultaneous determination of antihypertensive drugs' mixture atenolol and amiloride in both pharmaceutical dosage forms and in biological samples (urine). Silver nanoparticles were prepared by chemical reduction of silver nitrate using hydroxylamine HCL in an alkaline medium. Application of silver-hydroxylamine nanoparticles (SH NPs) provides many advantages including reproducibility, sensitivity, and cost effective way of analyte determination. Amiloride has four amino groups which act as attachment points on the surface of silver nanoparticles resulting in a synergistic effect on the absorption intensity of atenolol, leading to increase the sensitivity of the determination of both compounds. This method shows excellent advantages comparing with the previously reported methods, including accuracy, precision, and selectivity. The linear range of atenolol is 1 × 10−5–1 × 10−4 mol·L−1 and of amiloride is 1 × 10−6–1 × 10−5 mol·L−1. The limit of detection (LOD) values of atenolol and amiloride are 0.89 × 10−5 and 0.42 × 10−6 mol·L−1, respectively.


Introduction
Atenolol (ATN) is a β 1 -selective adrenoreceptor antagonist, a drug belonging to the beta blockers. ATN is used primarily in cardiovascular diseases either alone or concurrently with other antihypertensive drugs because of their additive e ects in the treatment of myocardial infarction, arrhythmias, and angina. It decreases heart rate and the force of the heart muscle contraction and reduces blood pressure by blocking the action of the nervous system on the heart [1].
Amiloride (AML) is a mild potassium-sparing diuretic that acts by inhibiting sodium-potassium ion exchange through blocking the distal renal tubule of the nephron [2].
Literature survey reveals that few analytical methods have been reported for the simultaneous determination of ATN and AML in pharmaceutical dosage forms and in some biological samples, for example, urine, blood, and plasma. RP HPLC method was applied for simultaneous estimation of both analytes in the presence of hydrochlorothiazide [3]. HPLC and chemometric-assisted spectrophotometric methods were reported for determination of ATN, AML, and chlorothalidone [4]. ATN and AML were simultaneously investigated in their pharmaceutical tablets using capillary zone electrophoresis [5,6]. Simultaneous resolution of ATN, AML, hydrochlorothiazide, and timolol was studied employing di erent chemometric methods [7]. Di erent antihypertensive drugs including ATN and AML were determined using rst-derivative nonlinear variable-angle synchronous uorescence spectrometry [8].
Silver nanoparticles (AgNPs) have been the focus of research for many years because of their interesting optical properties [9,10]. When AgNPs are scattered in liquid media, they exhibit a strong UV-visible extinction band which is not present in the spectrum of the bulk metal. is extinction band results when the incident photon frequency is resonant with the collective excitation of the conduction electrons and is known as the surface plasmon resonance (SPR) [11][12][13][14]. e plasmon resonance absorption of AgNPs has a molar extinction coe cient (3 × 10 11 M −1 ·cm −1 ) [15], which allows higher sensitivity in optical detection methods than conventional reagents.
Localized surface plasmon resonance (LSPR) is a type of surface plasmon excitations. It happens when light hits a nanoparticle having a size smaller than the wavelength of the incident light. e incident photon may combine with the metal electrons and begin to oscillate coherently [16,17]. As LSPR is sensitive to material type, size, and dielectric constant, it is considered to be a powerful technique that has been used recently in biosensing and biomedical applications [18,19].
Moreover, LSPR is responsible for enhancing the surface sensitivity of di erent spectroscopic methods including uorescence [20] and Raman scattering [21,22]. e reported applications of LSPR found in literature are based on the optical detection and its enhancement such as in surface enhanced Raman spectroscopy (SERS) which is applied for molecule detection using the extinction of metal nanoparticles [23][24][25].
After careful survey, it has been concluded that this research is considered the rst e ort for the simultaneous quantitative determination of ATN and AML in laboratory-made mixtures, pharmaceutical dosage forms, and in biological uids (urine) using LSPR produced from SH NPs.
is approach is based on the adsorption interaction between the studied analytes and the synthesized AgNPs resulting in enhancement e ect in the UV absorption intensities of the mixed analytes. is enhancement provides a more sensitive and accurate quantitative tool for analytical applications.

Experimental
2.1. Chemicals. Silver nitrate, hydroxylamine HCL, sodium hydroxide, and the essential chemicals for preparation of SH NPs were purchased from Sigma-Aldrich. Potassium nitrate and potassium chloride were purchased from Sigma-Aldrich and used to adjust the ionic strength. ATN and AML compounds were generously donated from EPICO Co, Cairo, Egypt. Distilled water was used for the preparation of all solutions throughout the experiment. Atenoretic ® capsules were purchased from the local market, containing 50 mg ATN and 2.5 mg AML.

Instruments.
e extinction spectra were recorded using a computerized, UV-visible spectrophotometer (UV-1601 PC, Shimadzu, Japan) with 1.0 cm quartz cells.
Characterization of the synthesized SH NPs was done using a transmission electron microscope (TEM; FEI TECNAI F20) and a scanning electron microscope (SEM; FEI Quanta 200 FEGSEM).

Synthesis of SH NPs
. SH NPs were prepared following the procedure described by Leopold and Lendl [26] using hydroxylamine HCL in an alkaline medium as a reducing agent for chemical reduction of silver nitrate solution. e concentration of silver nitrate in the prepared solution mixture was set to be 1 ×10 −3 mol·L −1 . A solution mixture of 6 × 10 −2 mol·L −1 hydroxylamine HCL and 0.1 mol·L −1 NaOH was rapidly added to the silver ion solution with shaking until milky grey color colloids were obtained. e pH tends to decrease with time because of the formation of nitrogen dioxide as a gaseous reaction product. erefore, sodium hydroxide solution (0.1 mol·L −1 ) was added to the solution mixture to adjust the pH value. e pH value of the applied SH NPs is 6.0, as the prepared colloids were aged for one day prior to its use. e calculated molar concentration of the prepared AgNPs was 5 × 10 −7 mol·L −1 [27].

Simultaneous Determination of ATN and AML.
In a typical procedure for determining the studied analytes, 100 µL of the prepared SH NPs, 1.0 mL of 50 mmol·L −1 KNO 3 solution, and di erent concentrations of both ATN and AML in mixture were transferred into a 10 mL volumetric ask. en the mixture was diluted to the mark with distilled water to reach the nal concentrations of the investigated drugs that lie under the studied calibration ranges. Finally, the reaction solution was transferred into a 1 cm spectrometric cell to record the absorption spectra of the studied concentrations of ATN and AML. e calibration curves of both analytes were constructed using the absorbance enhancement at 274 nm for ATN and 364.5 nm for AML. A blank experiment was also carried out under the same conditions without adding the studied analytes.

Applications of the Proposed Method.
e content of ten capsules was obtained, and the average weight of one capsule's content was weighed and accurately transferred into a 100 mL volumetric ask containing distilled water. e ask content was sonicated for 30 min and then completed to the mark with distilled water. After ltration, one milliliter of the clear ltrate was taken, and the procedure was conducted as previously described. In the case of urine sample analysis, the urine sample was diluted 50 times before the application to minimize the e ect of the complicated matrix.
e procedure was conducted as described in Experimental.

Characterization of SH NPs.
In order to characterize the prepared colloids, TEM images were recorded for the prepared SH NPs. Figure 1 shows the extinction spectrum of SH NPs after dilution of the prepared colloids ten times with distilled water. e maximum extinction is located at 416 nm which is in agreement with the reported approach suggested by Leopold and Lendl [26]. e full width at half maximum (fwhm) is the indication of the particle dispersion. It has been calculated to be 166 nm which indicated the polydispersion of the particles.

Synergistic E ect Based on LSPR of AML and ATN.
Since pKa values of ATN and AML molecules are 9.7 and 8.6, respectively, and because the SH NPs have pH 6.0, the protonated form of both analytes will be considered.
SH NPs with a negative charge in their surface are able to distribute from each other through the electrostatic repulsion. In the case of ATN, it was previously reported that the nitrogen atoms in the amino groups have more positive charges, while the negative charge is mainly located on oxygen atoms and on aromatic ring [28]. Di erent from the ATN molecule, AML contains four amino groups. ese groups can make the molecule to carry a positive charge at a speci c pH, enabling AML from adsorption onto the negatively charged surface of SH NPs through the electrostatic attraction [29,30]. Figure 2 describes a scheme suggesting the mechanism of interaction between the studied analytes and SH NPs.
In aqueous solution, ATN and AML show absorption band at 281 and 364.5 nm, respectively ( Figure 3). Upon addition of ATN and AML molecules to the prepared SH NPs, one new band appeared at 274 nm for ATN. e appearance of the absorption bands of the drugs and the disappearance of absorption peak of SH NPs may be attributed to the adsorption of the drugs' molecule containing six amino groups totally on the silver nanostructures surface. is phenomenon had been seen in studying the interaction of plasmon and molecular resonance for R6G and AgNPs [31].
From Figure 3, we can notice two main points. e rst one is the enhancement e ect of the absorption intensity of the studied analyte mixture upon adsorption on the surface of SH NPs. e enhancement e ect of ATN plasmon band provides a sensitive determination of ATN in the presence of AML. e second point is the appearance of an absorption band at 274 nm which is attributed to light absorption of ATN; while in the case of absence of SH NPs, this band is not distinguished. So, by adding the prepared colloids as a substrate for the analysis of ATN and AML mixture, this will provide an accurate and sensitive simultaneous quantitative determination in laboratory-made mixtures, pharmaceutical dosage forms, and in urine samples.

Optimization of Experimental Parameters.
e ability of SH NPs to enhance the absorption spectrum of the studied mixture is greatly a ected by di erent experimental parameters such as pH, ionic strength, and SH NP concentration. So, each parameter was studied and optimized to establish the analytical performance of the approach, while keeping other factors constant.

E ect of pH.
e interaction between the prepared SH NPs and the studied analytes is signi cantly a ected by the pH value of the solution. e pH may alter the surface charge of the colloids and hence may interfere the interaction with the analytes. Considering a mixture of 1 ×10 −4 mol·L −1 ATN and 5 × 10 −6 mol·L −1 AML, the absorption intensity at   Journal of Analytical Methods in Chemistry 364.5 nm as a representative example was measured against di erent pH values. It is important to select the optimum pH value that gives the maximum intensity at 364.5 nm. So, pH ranging from 3 to 10 was investigated by adjusting the pH value of SH NPs using 0.1 mol·L −1 NaOH and 0.1 mol·L −1 H 3 PO 4 solutions. e optimization results of the pH values are presented in Figure 4, and it can be seen that the highly acidic or highly basic conditions have negative e ect on the absorption intensity via decreasing the absorbance value at 364.5 nm which is not required. While the maximum intensity was obtained when the pH was ranged from 5 to 6, it was selected as an optimum pH value throughout the whole experiments. is result is agreed with the previously studied research that suggested that the electrostatically stabilized nanoparticles are greatly a ected by the change in pH [32].

E ect of Type and Ionic Strength of Aggregating
Agent. e type of electrolytes as the aggregating agent has been tested (KNO 3 and KCL solutions) to obtain the optimum type that will be used throughout the whole experiment. From Figure 5(a), we can conclude that the addition of nitrate ions enhanced the aggregation of SH NPs rather than chloride ions. It is reported that the aggregating agent may compete with the analyte for the surface of the colloid.
is phenomenon was explained previously [33], and it was reported that nitrate anions as aggregating agent are more easily displaced than chloride anions, and the e ect of ionic strength was optimized by addition of different concentrations of potassium nitrate solution to the prepared SH NPs and studied their e ect on the absorption intensity of the mixed analytes (1 ×10 −4 mol·L −1 ATN and 5 × 10 −6 mol·L −1 AML). Potassium nitrate concentrations were ranged from 12.5 to 62.5 mmol·L −1 . Figure 5(b) shows that the more intense absorbance can be obtained when more concentrated KNO 3 solution was used, until it reached 50 mmol·L −1 , and then no further signi cant absorbance increase is found. ereby, 50 mmol·L −1 KNO 3 was selected as an optimum concentration of the electrolyte solution. For further conrmation of the aggregation e ect of KNO 3 on SH NPs, a SEM image was monitored for SH NPs after addition of 50 mmol·L −1 .

E ect of SH NP Concentration. SH NP concentration has a signi cant e ect on the interaction of NPs with ATN and AML molecules.
e absorption spectra of the reaction mixture with a variety of SH NP volumes are given in Figure 6. e studied volumes of the prepared SH NPs were ranged from 100 to 1000 µL using 1 ×10 −4 mol·L −1 ATN and 5 × 10 −6 mol·L −1 AML in mixture and 50 mmol·L −1 KNO 3 as an aggregating agent. As it is shown, high intensities and hence high sensitivity were obtained with a low NP volume. ereby, 100 µL of SH NPs was selected to be the optimum volume throughout the whole experiments. Figure 2 shows the interaction between SH NPs and ATN molecule. In the case of AML, the interaction points with SH NPs are four protonated amino groups. is explains the high sensitivity of AML's determination (1 ×10 −6 -1 ×1 0 −5 mol·L −1 ) rather than the sensitivity of ATN (1 ×10 −5 -1 ×10 −4 mol·L −1 ). Figure 7(a) shows the spectral change of seven absorption spectra with increasing the concentration of the mixed analytes. Two calibration curves of the mixed solutions of ATN and AML were constructed (three replicates for each reading) by recording the absorption intensities at 274 nm for ATN and 364.5 nm for AML (Figure 7(b)). e statistical parameters required for the evaluation of linearity of the developed method as stated by ICH guidelines [34] are summarized in Table 1.

Linearity.
For further evaluation of the linearity, the Mandel tting test [35] was done, where at 95% con dence level, the critical  F value is equal to 7.7. As the calculated F values (7.8 × 10 −9 ) for ATN and (7.2 × 10 −8 ) for AML are less than the critical F value, indicating that the linear regression is the best way to describe this relationship.

Precision and Accuracy.
e precision of the developed method was evaluated by testing the intraday precision by analysis of six replicate separate solutions of the working standard mixtures of ATN and AML at three di erent concentration levels for each analyte. Interday precision was examined by repeating the analysis of the studied mixture over a period of three consecutive working days. e precision results are calculated as RSD% which was found to be ≤3.1 indicating good repeatability and reproducibility of the proposed method (Table 1).

Selectivity.
In order to investigate the selectivity of the proposed method, the general procedure was followed in the presence of 1 ×10 −4 mol·L −1 ATN and 5 × 10 −6 mol·L −1 AML with some common interfering ions such as (ascorbic acid, Ni 2+ , Na + , Ca 2+ , NH 4 + , SO 4 2− , and PO 4 3− ) at a concentration of 1 ×10 −3 mol·L −1 . From the obtained results in Table 2, it can be indicated that the proposed method has no interference even in the presence of high concentrations of other interfering ions.

Robustness.
It was examined by evaluating the inuence of small variation of method variables including; concentration of SH NPs, concentration of KNO 3 and the volume taken of the studied analytes on the method suitability and sensitivity. Results are shown in Table 3. It was found that none of these variations a ect the method signi cantly, indicating the reliability of the proposed method during normal usage and so the proposed method is considered robust.

Application of the Proposed Method.
e developed method was applied for the determination of the investigated analytes in laboratory-prepared mixture by varying the concentrations of each drug using 100 µL SH NPs and 50 mmol·L −1 KNO 3 . As shown in Table 4, high recovery percentages indicate that the method can be successfully applied with high accuracy for the determination of the interested analytes.  (1), df2 (n-3) � (1,4)), f limit of detection, g limit of quantitation, h standard error, i method standard deviation, j relative standard deviation, and k average of six determinations at three di erent concentration levels.  e excellent recovery percent values indicated the potential of the method for determining both analytes in the pharmaceutical dosage forms without su ering from the interferences of the present excipients (Table 5).
To further discover the practical application of the proposed method, a quantitative analysis of the interested drugs in spiked urine samples was done. Two di erent amounts of known concentration of ATN and AML in mixture were spiked to reach a nal concentration of 1 ×10 −4 mol·L −1 for ATN and 5 × 10 −6 mol·L −1 for AML. From the resulted recovery data (Table 5), it can be implied that the method is reliable and could be applied successfully in biological samples. Table 6 represents a comparison between the proposed method and other previous reported methods that was used for simultaneous determination of ATN and AML. It can be concluded that the proposed method provides higher sensitivity, wider linear range, and lower detection limit with the simplicity of the instrument used comparing with spectroscopic techniques.

Conclusion
is contribution is considered the rst e ort to utilize the LSPR resulting from SH NPs prepared by reduction of silver nitrate using hydroxylamine HCL for the simultaneous determination of the studied drugs. e developed method is based on the enhancement e ect of plasmon resonance of   AML containing four amino groups as attachment points on SH NPs. is e ect makes a synergistic behavior resulting in an increase in the sensitivity of ATN and AML determinations. Besides the enhancement e ect, this approach carries many advantages of the simplicity and reproducibility as well as low cost application. From the obtained results, it can be concluded that the proposed method is applied successfully for the analysis of the investigated drugs in their laboratory mixtures, pharmaceutical capsules, and in spiked urine samples.

Conflicts of Interest
e author reports no con icts of interest.