Journal of Nanomaterials

Volume 2013 (2013), Article ID 514781, 8 pages

http://dx.doi.org/10.1155/2013/514781

Research Article

Low-Temperature Transformations of Protonic Forms of Layered Complex Oxides HLnTiO₄ and H₂Ln₂Ti₃O₁₀ (Ln = La, Nd)

L. D. Abdulaeva,¹ O. I. Silyukov,¹ Yu. V. Petrov,² and I. A. Zvereva¹

¹Faculty of Chemistry, Saint-Petersburg State University, Universitetsky Prospekt 26, Saint Petersburg 198504, Russia

²Interdisciplinary Resource Center for Nanotechnology, Saint-Petersburg State University, Universitetsky Prospekt 26, Saint Petersburg 198504, Russia

Received 27 September 2012; Revised 14 January 2013; Accepted 16 January 2013

Academic Editor: Hua Yang

Copyright © 2013 L. D. Abdulaeva et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

In the present work protonic forms of layered Ruddlesden-Popper oxides HLnTiO₄ and H₂Ln₂Ti₃O₁₀ (Ln = La, Nd) were used as the starting point for soft chemistry synthesis of two series of perovskite-like compounds by acid leaching and exfoliation, promoted by vanadyl sulfate. The last route leads to the nanostructured VO²⁺ containing samples. Characterization by SEM, powder XRD, and TGA has been performed for the determination of the structure and composition of synthesized oxides.

1. Introduction

Layered perovskite-like oxides are compounds which consist of intergrowths of perovskite and other structures, and they are formed by two-dimensional nanosized perovskite slabs interleaved with cations or cationic structural units. Perovskite-like compounds can exhibit a wide range of important physical and chemical properties, such as superconductivity [1, 2], colossal magnetoresistance [3], ferroelectricity [4, 5], and catalytic and photocatalytic activity [6, 7].

In recent years, there has been a growing interest in using the soft chemistry methods for development of new layered perovskite-like compounds with specified physicochemical properties, as well as design of these materials based on the perovskite structure [8]. This is mostly due to the ability to preserve most of the structural and physical features of the initial substance in the course of these transformations.

Layered compounds HLnTiO₄ and H₂Ln₂Ti₃O₁₀ (Ln = La, Nd) are representatives of the Ruddlesden-Popper layered perovskite-type phases. They are formed by polyanion sheets of transition metal oxides (in case of HLnTiO₄ polyanion sheets consist of a single layer of oxygen octahedral [9] and, in case of H₂Ln₂Ti₃O₁₀, three layers of oxygen octahedral [10]) and protons in the interlayer space.

Protonic forms of transition metal-layered perovskite-like oxides attract great attention due to their interesting and variable properties, in particular the proton conductivity [11, 12]. Such protonated compounds are interesting in terms of their application as precursors for low-temperature reactions and as starting compounds for building nanostructured materials. Ion-exchange reactions of interlayer protons, acid leaching, and topochemical dehydration are the most important soft chemistry routes.

2. Experimental

2.1. Precursor Synthesis

Alkaline forms NaLnTiO₄ and K₂Ln₂Ti₃O₁₀ (Ln = La, Nd) of a powder were produced by ceramic technique as precursors for further synthesis of protonic forms. Stoichiometric mixtures of Ln₂O₃ (Ln = La, Nd), TiO₂, and sodium or potassium carbonate (40% excess, since it is volatilized at high-temperature synthesis) were taken as initial compounds; all substances were calcined to remove traces of moisture.

In case of NaLnTiO₄, following temperature mode has been used: fast heating to 780°C, calcinating at 780°C for 2 hours, fast heating to 900°C, and calcinating at 900°C for 3 hours [13]. This temperature mode was selected regarding the formation beginning of NaLnTiO₄ at 780°C, while Na₂CO₃ does not yet melt at this temperature. After NaLnTiO₄ formation, the temperature is increased to 900°C to obtain pure phase. For K₂Ln₂Ti₃O₁₀ fast heating to 1100°C was used, with calcinations for 6 hours. Syntheses took place according to the following reactions:

Protonic forms HLnTiO₄ (Ln = La, Nd) were obtained by substitution of Na⁺ ions in NaLnTiO₄ (Ln = La, Nd) to H⁺, according to the following reaction:

Initial alkali metal-containing layered compounds were treated in 0.1 H HCl acid medium, as described in [14].

XRD analysis (powder X-ray diffraction, CuKα radiation) was carried out to control the reaction and to determine structural parameters of substances (Figure 1).

(a)

(b)

Figure 1: X-ray powder patterns: (a) precursor NaLaTiO₄; (b) HLaTiO₄; (c) precursor NaNdTiO₄; (d) HNdTiO₄.

Calculated unit cell parameters of obtained samples (a) NaLaTiO₄, tetragonal, P4/nmm: , = 3,775 Å; = 13,018 Å; (b) NaNdTiO₄, tetragonal, P4/nmm: , = 3,771 Å; = 12,832 Å; (c) HLaTiO₄, tetragonal, P4/nmm: , = 3,753 Å; = 12,417 Å; (d) HNdTiO₄, tetragonal, P4/nmm: , = 3,708 Å; = 12,261 Å are in agreement with the literature data [9].

The degree of substitution of Na⁺ by H⁺ is estimated by means of TGA analysis using TG 209 F3 Iris, Netzsch [14, 15]. For example, the decomposition process of Na(1−x)HxNdTiO₄*H₂O can be represented by the following reaction:

The weight loss of the sample results from the sorbed water release (intercalated/adsorbed) and from water formed by decomposition of protonic form HNdTiO₄. The content of sodium ions remaining after release of all water substance depends on the degree of substitution of the sample. Dependence between the degree of substitution of and mass loss in mass loss curve can be expressed by the following relationship:

where is the mass of sample and M and A the molecular and atomic mass, respectively. parameter is the ratio of the mass remaining after the release of all water substances to the mass of water released during the decomposition of substituted compounds.

From (5), the degree of substitution and quantity of sorbed water can be calculated using the following formulas:

Calculated degrees of substitutes were found to be nearly 100% (±2%) for both HLaTiO₄ and HNdTiO₄.

SEM images (Zeiss Supra 40VP) show that the protonated samples keep the morphology of their layered Na precursors, where the particles are composed of layered plates that are typical for all layer compounds. The average thickness of the particles is about 300 nm. According to the X-ray microanalysis data, Na reflexes were not observed for all protonated substances.

2.2. Acid Leaching Processes

Cation-deficient perovskites Ln2/3TiO₃ (Ln = La, Nd) were obtained for the first time by leaching of Ln³⁺ ions from HLnTiO₄ in acid solution (10x excess of HCl solution (0.1 H) for 7 days):

During the leaching in HCl solution of varying concentrations, it was found that the right product can be obtained only under conditions. Ln2/3TiO₃ dissolved at higher concentration and reaction does not have time to pass through at lower concentration. In case of Nd2/3TiO₃ pure phase of the product was obtained, while for La2/3TiO₃ the impurity of stable HLnTiO₄*H₂O phase was observed [16] (Figure 2).

(a)

(b)

Figure 2: X-ray powder patterns: (a) HNdTiO₄; (b) HNdTiO₄ (4 days, excess of 0.1 H HCl); (c) Nd2/3TiO₃ (7 days, excess of 0.1 H HCl); (d) HLaTiO4,; (e) HLaTiO₄*H₂O (star) + La2/3TiO₃ (triangle) (7 days, excess of 0.1 H HCl).

The SEM shows that the initial morphology is not preserved for defect perovskites Ln2/3TiO₃ obtained by acid leaching. The resulting phase is characterized by irregularly shaped particles with dimensions less than 100 nm (Figure 3(c)).

(a)

(b)

(c)

Figure 3: SEM images: (a) NaNdTiO₄; (b) HNdTiO₄; (c) Nd2/3TiO₃.

The process of acid leaching of Ln³⁺ cations was also observed in reaction of a perovskite-oxide K₂Ln₂Ti₃O₁₀ (Ln = La, Nd) with a solution of hydrochloric acid of different concentrations. Initial compound K₂Ln₂Ti₃O₁₀ was treated by 5.5x excess of 2 M hydrochloric acid for 5 days. In the process, K⁺ ions are replaced by H⁺, according to the following reaction:

XRD analysis data showed that in case of the initial K₂La₂Ti₃O₁₀ the resulting compound contains a large number of impurity cation-deficient perovskite La2/3TiO₃ (Figure 4, b). In case of the initial K₂Nd₂Ti₃O₁₀, an amount of the Nd2/3TiO₃ is noticeably smaller (Figure 4, f). The main phase in both cases is partially hydrated compound H₂Ln₂Ti₃O₁₀*H₂O.

(a)

(b)

Figure 4: X-ray powder patterns: (a) K₂La₂Ti₃O₁₀ + 10x excess of HCl (0.1 M), 24 h; (b) K₂La₂Ti₃O₁₀ + 5.5x excess of HCl (2 M), 5d (H₂La₂Ti₃O₁₀ (rhombus), La2/3TiO₃ (star)); (c) K₂La₂Ti₃O₁₀ + 10x excess of HCl (0.1 M), 5d; (d) K₂Nd₂Ti₃O₁₀ + 10x excess of HCl (0.1 M), 24 h; (i) K₂Nd₂Ti₃O₁₀ + 5.5x excess of HCl (2 M), 5d, (H₂Nd₂Ti₃O₁₀ (rhombus), Nd2/3TiO₃ (star)); (f) K₂Nd₂Ti₃O₁₀ + 10x excess of HCl (0.1 M), 5d.

Further, it was proposed to reduce the concentration to 0.1 M solution of 10x excess HCl. This concentration was chosen by analogy with the reaction of a single-layer perovskite NaLnTiO₄ with hydrochloric acid solution, where the result is a pure phase HLnTiO₄. But in the case of three-layer perovskite oxides the desired product was also obtained with impurities of Ln2/3TiO₃ (Figure 4, c). Only short time treatment (24 hours, 0.1 M solution of 10x excess HCl) leads to the product with satisfactory amount of impurity (Figure 4, a and d).

The SEM images of samples show that the leaching results in the formation of square holes on the surface of the particles; the initial morphology of the layered oxide particles is preserved.

2.3. HLnTiO₄ (Ln = La, Nd) Exfoliation Promoted by VOSO₄

Treatment of NaLnTiO₄ (Ln = La, Nd) by aqueous solution of VOSO₄ leads to partial substitution of Na⁺ by (VO)²⁺ as described in [17] with preservation of layered structure and only partial exfoliation (Figure 5(a)). A similar reaction is known for the K₂La₂Ti₃O₁₀, as described in [18]. In case of protonic compound, the reaction goes another way; VOSO₄ causes exfoliation and reassembling of HLnTiO₄ particles.

(a)

(b)

(c)

Figure 5: SEM images: (a) NaNdTiO₄ + VOSO₄; (b) (VO)xH1−2xNdTiO₄ *H₂O; (c) (VO)xH1−2xNdTiO₄*H₂O, calcination 300°C, 30 min.

Exfoliated HLnTiO₄ (Ln = La, Nd) were prepared by treatment of initial HLnTiO₄ in a double excess of VOSO₄ aqueous solution at 80°C for 3 days. As a result a dark green powder was obtained. The particles of the obtained samples consist of a number of interconnected flat crystallites less than 10 nm width (Figure 5(b)).

The X-ray powder patterns (b) of obtained substances are close to the initial HLnTiO₄ (Figure 6). Exfoliated compounds contain significant amounts of adsorbed VO²⁺ cations (more than 15% mass) according to the X-ray microanalysis.

Figure 6: X-ray diffraction patterns: (a) HNdTiO₄; (b) HNdTiO₄ exfoliated; (c) HNdTiO₄ exfoliated, calcinations at 300°C, 30 min; (d) Nd₂□Ti₂O₇ by pyrolysis at 680°C.

TGA shows that samples lose water during heating from 30 to 700°C, and in both La and Nd cases the mass loss is nearly the same, 12-13% of the total mass of the substance. The porous nature of the particles explains the continuous nature of mass loss on the TGA curves. This is in contrast with HNdTiO₄ and HLaTiO₄ dehydration from 250°C and 350°C, respectively (Figure 7).

Figure 7: TGA analysis: (a) HNdTiO₄; (b) HLaTiO₄; (c) (VO)xH1−2xNdTiO₄*H₂O; (d) (VO)xH1−2xLaTiO₄*H₂O.

XRD patterns of dehydrated (VO)xH1−2xLnTiO₄*H₂O compounds are nearly the same for 150°C, 300°C, and 600°C temperatures. Total reduction of peaks intensity and 001 reflex displacement in small angle region to large angles (c) is natural because a new phase is formed, identified as Ln₂□Ti₂O₇. It has cell parameters close to the obtained by pyrolysis of the HLnTiO₄ substance, but less peak broadening on the XRD pattern. The SEM images of dehydrated phases are close to the images of corresponding hydrated (VO)xH1−2xLnTiO₄*H₂O samples.

2.4. H₂Nd₂Ti₃O₁₀*yH₂O Exfoliation Promoted by VOSO₄

In case of protonic form of three-layer perovskite-like oxide H₂Nd₂Ti₃O₁₀*H₂O, we carried out the treatment in a double excess of VOSO₄ aqueous solution at 80°C for 3 days. The resulting dark green powder was washed with distilled water and dried under CaCl₂.

XRD analysis showed that formation of new phases was not observed during the exfoliation synthesis; diffraction patterns of the initial hydrated and protonated H₂Nd₂Ti₃O₁₀*H₂O and the sample treated by VOSO₄ are almost identical, both containing a small amount of Nd2/3TiO₃ impurity (Figure 8).

Figure 8: X-ray diffraction patterns: (a) H₂Nd₂Ti₃O₁₀*H₂O; (b) (VO)xH2−2xNd₂Ti₃O₁₀*H₂O.

TGA curve of H₂Nd₂Ti₃O₁₀ exfoliated by VOSO₄ ((VO)H2−2xNd₂Ti₃O₁₀*H₂O) has mass area during the heating from 30 to 100°C corresponding to the surface water, which is not observed in the case of initial protonated phase (Figure 9). In other (VO)xH2−2xNd₂Ti₃O₁₀*H₂O decomposition behavior in general is similar to the initial H₂Nd₂Ti₃O₁₀*H₂O one.

Figure 9: TGA analysis: (a) H₂Nd₂Ti₃O₁₀*H₂O; (b) (VO)xH2−2xNd₂Ti₃O₁₀*H₂O.

Surface analysis by SEM demonstrated that the compound in general keeps the particle size of the layered precursor, but there are significant amounts of particles with exfoliated surface layers (Figure 10) similarly as in the case of single-layer perovskite-like oxides HLnTiO₄ (Ln = La, Nd). And in contrast with single-layered phases, the amount of adsorbed VO²⁺ cations is less than 5% mass according to the X-ray microanalysis. The mass ratio of Ti and Nd was not changed in contrast with initial protonated compound.

(a)

(b)

Figure 10: SEM images: (a) H₂Nd₂Ti₃O₁₀; (b) (VO)xH2−2xNd₂Ti₃O₁₀.

3. Conclusions

Cation-deficient perovskites Ln2/3TiO₃ (Ln = La, Nd) were obtained for the first time by leaching of Ln³⁺ ions from HLnTiO₄ in acid solution (10x excess of HCl solution (0.1 H) for 7 days) (Scheme 1). In case of Nd2/3TiO₃ pure phase of the product was obtained, while for La2/3TiO₃ the impurity of stable HLnTiO₄*H₂O phase was observed.

Scheme 1: Structural transformation of HLnTiO₄ (Ln = La, Nd): Ln2/3TiO₃ by acid leaching; (VO)xH1−2xLnTiO₄*H₂O by ion-exchange reactions.

Exfoliated (VO)xH1−2xLnTiO₄*H₂O (Ln = La, Nd) have been prepared for the first time by the ion-exchange reaction of HLnTiO₄ in aqueous VOSO₄. They consist of a large number of interconnected flat crystallites less than 10 nm in size with large amount of surface adsorbed VO²⁺ and water molecules (Scheme 1).

The process of acid leaching of Ln³⁺ cations was also observed in reaction of a perovskite-type layered oxide K₂Ln₂Ti₃O₁₀ (Ln = La, Nd) with a solution of hydrochloric acid of different concentrations. Resulting compounds contain a large number of impurity cation-deficient perovskites Ln2/3TiO₃.

In case of three-layer perovskite-like oxide H₂Nd₂Ti₃O₁₀, the treatment with VOSO₄ aqueous solution at 80∘C for 3 days leads to the compound with significant amount of exfoliated surface layers. But in general, it keeps the particle morphology of the precursor.

Acknowledgments

This work has been supported by the RFBR (Grant 12-03-00761). Powder X-ray study is carried out in the X-ray Diffraction Centre of Saint Petersburg State University. SEM study is carried out in the Interdisciplinary Resource Center for Nanotechnology of Saint Petersburg State University.

References

K. D. Otzschi, K. R. Poeppelmeier, P. A. Salvador, T. O. Mason, H. Zhang, and L. D. Marks, “A new series of layered cuprates (ACuO2.5)₂(ATiO₃)(m): Dy₂Ba₂Ca₂Cu₂Ti₄O₁₇, ,” Journal of the American Chemical Society, vol. 118, no. 37, pp. 8951–8952, 1996.

P. A. Salvador, K. B. Greenwood, J. R. Mawdsley, K. R. Poeppelmeier, and T. O. Mason, “Substitution behavior and stable charge carrier species in long-bond length layered cuprates,” Chemistry of Materials, vol. 11, no. 7, pp. 1760–1770, 1999.

Y. Moritomo, A. Asamitsu, H. Kuwahara, and Y. Tokura, “Giant magnetoresistance of manganese oxides with a layered perovskite structure,” Nature, vol. 380, no. 6570, pp. 141–144, 1996.

J. Lago, P. D. Battle, and M. J. Rosseinsky, “Weak ferromagnetism and spin-glass behaviour of the Ruddlesden-Popper compound Ca₄Mn₃O₁₀: a dc magnetization study,” Journal of Physics Condensed Matter, vol. 12, no. 11, pp. 2505–2524, 2000.

Y. K. Tang, X. Ma, Z. Q. Kou et al., “Slight la doping induced ferromagnetic clusters in layered (),” Physical Review B, vol. 72, no. 13, Article ID 132403, 4 pages, 2005.

T. Takata, Y. Furumi, K. Shinohara et al., “Photocatalytic decomposition of water on spontaneously hydrated layered perovskites,” Chemistry of Materials, vol. 9, no. 5, pp. 1063–1064, 1997.

H. G. Kim, D. W. Hwang, J. Kim, Y. G. Kim, and J. S. Lee, “Highly donor-doped (110) layered perovskite materials as novel photocatalysts for overall water splitting,” Chemical Communications, no. 12, pp. 1077–1078, 1999.

R. E. Schaak and T. E. Mallouk, “Perovskites by design: a toolbox of solid-state reactions,” Chemistry of Materials, vol. 14, no. 4, pp. 1455–1471, 2005.

S. H. Byeon, J. J. Yoon, and S. O. Lee, “A new family of protonated oxides HLnTiO₄ (, Nd, Sm, and Gd),” Journal of Solid State Chemistry, vol. 127, no. 1, pp. 119–122, 1996.

J. Gopalakrishnan and V. Bhat, “A₂Ln₂Ti₃O₁₀ ( or Rb, or rare earth): a new series of layered perovskites exhibiting ion exchange,” Inorganic Chemistry, vol. 26, pp. 4301–4303, 1987.

V. Thangadurai, A. K. Shukla, and J. Gopalakrishnan, “Proton conduction in layered perovskite oxides,” Solid State Ionics, vol. 73, no. 1-2, pp. 9–14, 1994.

G. Mangamma, V. Bhat, J. Gopalakrishnan, and S. V. Bhat, “NMR study of fast protonic conduction in layered ,” Solid State Ionics, vol. 58, no. 3-4, pp. 303–309, 1992.

I. A. Zvereva, O. I. Silyukov, A. V. Markelov et al., “Formation of the complex oxide NaNdTiO₄,” Glass Physics and Chemistry, vol. 34, no. 6, pp. 749–755, 2008.

I. A. Zvereva, O. I. Silyukov, and M. V. Chislov, “Ion-exchange reactions in the structure of perovskite-like layered oxides, I: protonation of NaNdTiO₄ complex oxide,” Russian Journal of General Chemistry, vol. 81, pp. 1434–1441, 2011.

O. Silyukov, M. Chislov, A. Burovikhina, T. Utkina, and I. Zvereva, “Thermogravimetry study of ion exchange and hydration in layered oxide materials,” Journal of Thermal Analysis and Calorimetry, vol. 110, pp. 187–192, 2012.

K. Yoshii, “Synthesis and magnetic properties of Ln2/3TiO₃ ( and Nd),” Journal of Solid State Chemistry, vol. 149, no. 2, pp. 354–359, 2000.

D. Neiner, V. Golub, and J. B. Wiley, “Synthesis and characterization of the new layered perovskite, Na 0,10(VO)0,45LaTinH₂O,” Materials Research Bulletin, vol. 39, no. 10, pp. 1385–1392, 2004.

J. Gopalakrishnan, T. Sivakumar, K. Ramesha, V. Thangadurai, and G. N. Subbanna, “Transformations of Ruddlesden-Popper oxides to new layered perovskite oxides by metathesis reactions,” Journal of the American Chemical Society, vol. 122, no. 26, pp. 6237–6241, 2000.