This study reports characteristics of dye-sensitized solar cells (DSSCs) with graphene/ZnO nanoparticle bilayer structure. The enhancement of the performance of DSSCs achieved using graphene/ZnO nanoparticle films is attributable to the introduction of an electron-extraction layer and absorption of light in the visible range and especially in the range 300–420 nm. DSSC that was fabricated with graphene/ZnO nanoparticle film composite photoanodes exhibited a Voc of 0.5 V, a Jsc of 17.5 mA/cm2, an FF of 0.456, and a calculated η of 3.98%.
1. Introduction
Graphene has attracted much interest because of its unique properties and potential applications. As the thinnest 2D material, graphene has a high carrier mobility [1] and an excellent optical transparency [2]. Graphene and its derivatives have been used in transparent conductive films [3], as a new class of efficient hole- and electron-extraction materials [4–6], and in organic photovoltaic (PV) cells [7, 8]. Graphene films can be prepared using various techniques, including the micromechanical exfoliation of graphite [9], chemical vapor deposition (CVD) [10–14], the solution-based chemical reduction of graphene oxide to graphene [15–19], and magnetron sputtering, which has many advantages such as low cost, large scale, and ease of control.
The nanostructures of ZnO films can easily be tuned by modifying the growth solution and the use of ultrasonic spraying [20]. ZnO can also be tailored to various nanostructures, such as nanorods/nanowires [21–25], nanotubes [24–27], nanoflowers [28], and nanosheets [29, 30], which have high electrical conductivity and enhanced photon absorption, supporting improved short-circuit current density and overall light conversion efficiency [31].
In this work, a graphene film with high electron mobility is incorporated into a ZnO nanoparticle film to form a compact layer for use in dye-sensitized solar cells. This investigation studies the optical, structural, and surface properties of a graphene film that is grown on ITO electrodes by radiofrequency magnetron sputtering, as functions of thickness, in high-performance DSSCs. The introduction of the sputtered graphene film (electron-extraction layer) with optimal thickness enhances the efficiency of conversion of the DSSCs.
2. Experimental Setup
In this study, a graphene film was prepared on ITO glass using a radio frequency magnetron sputtering system. Table 1 lists the typical deposition conditions for the graphene film. The resistivity of the graphene film is around 2.2×103 ohm-cm. The ZnO nanoparticle film was deposited by ultrasonic spray pyrolysis at atmospheric pressure on ITO/graphene glass. Three aqueous solutions, Zn(CH3COO)2·2H2O (0.5 mol/l), CH3COONH4 (2.5 mol/l), and In (NO3)3 (0.5 mol/l), were used as sources of zinc, nitrogen, and indium, respectively. The atomic ratio of Zn/N in the N-doped film was 1 : 2 and that of Zn/N/In in the N-In codoped film was 1 : 2 : 0.15 [20]. An aerosol of the precursor solution was produced using a commercial ultrasonic nebulizer. Colloidal TiO2 was prepared from 6 g nanocrystalline powder (Degussa, P25 titanium oxide, Japan) and both 0.1 mL of Triton X-100 and 0.2 mL of acetylacetone, which were stirred together for 24 hrs. Subsequently, the mixture was spin-coated on ITO glass and ITO/graphene/ZnO substrate to a thickness of approximately 15 μm, and a 3×3 mm2 active area was defined. Thereafter, the prepared thin film photoelectrode was immersed in a 3×10-4 M Ru-metal complex dye, D719 ([RuL2(NCS)2] : 2 TBA), at room temperature for 24 hrs, before it was sintered at 450 or 500°C for 30 min, to increase its anatase content (anatase : rutile = 85 : 15) [32]. The electrolyte included 0.05 M iodide, 0.5 M lithium iodide, and 0.5 M 4-tert-butylpyridine (TBP) in propylene carbonate. A 100 nm thick layer of platinum was sputtered onto the ITO substrate to form a counter electrode. Cells were fabricated by placing sealing films between the two electrodes, leaving only two via-holes for injection of the electrolyte. The sealing process was performed on a hot plate at 100°C for 3 min. Then, the electrolyte was injected into the space between the two electrodes through the via-holes. Finally, the via-holes were sealed using epoxy at a low vapor transmission rate. Figure 1 schematically depicts the complete structure.
Typical deposition conditions for graphene film.
Target
Graphite
Target diameter
5 cm
Substrate-to-target distance
4 cm
RF power
90 W
Sputtering ambient
Ar
Gas flow rate
90 sccm
Residual pressure
<5 × 10−6 Torr
Sputtering pressure
3.1 mTorr
Deposition time
40 min
Schematic of DSSCs with graphene/ZnO nanoparticle film.
A field emission scanning electron microscope (FESEM) (LEO 1530) was adopted to examine the cross-section and surface morphology of the cells. Additionally, the current density-voltage (J-V) characteristics were measured using a Keithley 2420 programmable source meter under irradiation by a 1000 W xenon lamp. Finally, the irradiation power density on the surface of the sample was calibrated as 1000 W/m2.
3. Results and Discussion
Figures 2(a) and 2(b) present the surface and cross-sectional FESEM images of the ZnO nanoparticle films on glass substrate. The surface images clearly reveal that ZnO nanoparticle films are highly dense and grown vertically on glass substrates, as shown in Figures 2(a) and 2(b). The high-resolution image reveals that the obtained ZnO nanoparticle films exhibited hexagonal morphology with an average nanoparticle diameter of 300~330 nm. Figure 2(c) shows a typical X-ray diffraction (XRD) pattern of ZnO film. Three dominant diffraction peaks, ZnO(100) (2θ=31.76°), ZnO(002) (2θ=34.46°), and ZnO(101) (2θ=36.27°), are observed. That demonstrates a typical ZnO polycrystalline structure.
(a) FESEM surface image of photoanode with ZnO nanoparticle film. (b) FESEM cross-section image of ZnO nanoparticle film. (c) XRD pattern of ZnO nanoparticles film.
Figure 3 presents the absorption spectra of the TiO2, ZnO nanoparticle, and graphene/ZnO nanoparticle/TiO2 films. The ZnO nanoparticle thin film yields a strong absorption peak at ~380 nm, revealing the existence of crystalline wurtzite hexagonal ZnO. The DSSC with the graphene film clearly has higher absorption intensity than the DSSC without the graphene film in the visible range, and especially in the range 300–420 nm.
Absorbance spectra of TiO2, ZnO nanoparticle, and graphene/ZnO nanoparticle/TiO2 film.
Figure 4 shows the XRD plots of the TiO2 film electrodes before and after annealing. The TiO2 films were dried in air at room temperature for 10 min and then annealing at 450°C for 30 min. Two dominant anatase diffraction peaks, (101) (2θ=25.28°) and (004) (2θ=37.73°), are observed. Following annealing, the sample was highly crystalline and all of the diffraction peaks could be indexed to anatase TiO2.
XRD pattern of TiO2 on glass substrate (A: anatase, R: rutile).
In optoelectronic devices, proper contact between the electrode and the transporter (recombination and back transfer) is crucial for charge collection. Figure 5 presents the schematic energy level diagram of the DSSCs with the graphene and ZnO nanoparticle film. Graphene has a work function (−4.42 eV versus vacuum) similar to that of the ITO (−4.8 eV versus vacuum) electrode. The graphene does not prevent the flow of injected electrons down to the ITO electrode because its work function exceeds that of the ITO electrode [33–35]. Therefore, the implanted graphene collects electrons and acts as a transporter in the effective separation of charge and rapid transport of the photogenerated electrons.
Energy level diagram and mechanism of photocurrent generation in DSSCs with GO and ZnO nanoparticles.
Based on the above discussion, the incorporation of graphene into ZnO nanoparticle film enables DSSC devices to operate more efficiently. Figure 6 plots photocurrent J-V curves of the DSSCs obtained under 100 mW/cm2 illumination and the AM 1.5 G condition without and with the graphene and ZnO nanoparticle film, fabricated on an ITO glass substrate. The cell has an active area of 3×3 mm2 and no antireflective coating. Table 2 presents the measured cell parameters—open-circuit voltage (Voc), short-circuit current (Jsc), fill factor (FF), and energy conversion efficiency (η). The DSSC that was fabricated with graphene/ZnO nanoparticle film composite photoanodes exhibited a Voc of 0.5 V, a Jsc of 17.5 mA/cm−2, an FF of 0.456, and a calculated η of 3.98%. Incorporating graphene oxide into the graphene film effectively decreases the internal resistance within the photoanodes and prolonged the electron lifetime. Therefore, the improved photovoltaic properties of DSSC with the graphene/ZnO nanoparticle film photoanode are attributable to the strong absorption of dye and the high light harvesting efficiency, which reduce electron recombination loss.
Parameters of TiO2 DSSCs with and without the graphene and ZnO nanoparticle film, fabricated on bare ITO glass substrate.
ITO/TiO2
ITO/ZnO nanoparticle/TiO2
ITO/graphene/ZnO nanoparticle/TiO2
Jsc (mA/cm2)
6.9
11.3
17.5
Voc (V)
0.5
0.45
0.5
F.F.
0.419
0.473
0.456
Efficiency
1.45
2.4
3.98
Current-voltage (J-V) characteristics of DSSCs fabricated with ITO/graphene/ZnO nanoparticle/TiO2 photoanodes under simulated illumination by a light intensity of 100 mW/cm2 (AM 1.5).
4. Conclusion
This work discusses the improvement that is made by the introduction of a sputtered graphene/ZnO nanoparticle film into DSSCs. The enhancement of the performance of DSSCs by the introduction of graphene/ZnO nanoparticle films may be attributed to the introduction of an electron-extraction layer and the absorption of light in the visible range, especially in the range 300–420 nm. A DSSC that was fabricated with graphene/ZnO nanoparticle film composite photoanodes had a Voc of 0.5 V, a Jsc of 17.5 mA/cm−2, an FF of 0.456, and a calculated η of 3.98%. Accordingly, the improvement of photovoltaic properties of DSSC by the introduction of the graphene/ZnO nanoparticle film photoanode is attributable to the strong absorption of dye and the high light harvesting efficiency, which can reduce the electron recombination loss. The above results demonstrate the potential application of graphene oxide to improve for enhancing the performance of ZnO nanoparticle-based DSSCs, which can be produced on a large scale at low cost.
Conflict of Interests
The authors declare that there is no conflict of interests regarding the publication of this paper.
Acknowledgment
Financial support of this paper was provided by the National Science Council of the Republic of China under Contract no. NSC 102-2622-E-027-021-CC3.
DuX.SkachkoI.BarkerA.AndreiE. Y.Approaching ballistic transport in suspended graphene2008384914952-s2.0-4944909107210.1038/nnano.2008.199NairR. R.BlakeP.GrigorenkoA. N.NovoselovK. S.BoothT. J.StauberT.PeresN. M. R.GeimA. K.Fine structure constant defines visual transparency of graphene2008320588113082-s2.0-4534909298610.1126/science.1156965BaeS.KimH.LeeY.XuX.ParkJ.-S.ZhengY.BalakrishnanJ.LeiT.Ri KimH.SongY. I.KimY.-J.KimK. S.ÖzyilmazB.AhnJ.-H.HongB. H.IijimaS.Roll-to-roll production of 30-inch graphene films for transparent electrodes2010585745782-s2.0-7795643082010.1038/nnano.2010.132LiuJ.XueY.GaoY.YuD.DurstockM.DaiL.Hole and electron extraction layers based on graphene oxide derivatives for high-performance bulk heterojunction solar cells20122417222822332-s2.0-8486032517710.1002/adma.201104945LiuJ.XueY.DaiL.Sulfated graphene oxide as a hole-extraction layer in high-performance polymer solar cells2012314192819332-s2.0-8486407400910.1021/jz300723hWangX.ZhiL.TsaoN.TomovićŽ.LiJ.MüllenK.Transparent carbon films as electrodes in organic solar cells20084716299029922-s2.0-4494918285810.1002/anie.200704909WangX.ZhiL.MüllenK.Transparentconductive graphene electrodes for dye-sensitized solar cells200781323327NovoselovK. S.GeimA. K.MorozovS. V.JiangD.ZhangY.DubonosS. V.GrigorievaI. V.FirsovA. A.Electric field in atomically thin carbon films200430656966666692-s2.0-744422064510.1126/science.1102896BergerC.SongZ.LiT.LiX.OgbazghiA. Y.FengR.DaiZ.AlexeiN.ConradM. E. H.FirstP. N.De HeerW. A.Ultrathin epitaxial graphite: 2D electron gas properties and a route toward graphene-based nanoelectronics20041085219912199162-s2.0-1994442800310.1021/jp040650fDatoA.RadmilovicV.LeeZ.PhillipsJ.FrenklachM.Substrate-free gas-phase synthesis of graphene sheets200887201220162-s2.0-5694909658810.1021/nl8011566KimK. S.ZhaoY.JangH.LeeS. Y.KimJ. M.KimK. S.AhnJ.-H.KimP.ChoiJ.-Y.HongB. H.Large-scale pattern growth of graphene films for stretchable transparent electrodes200945772307067102-s2.0-5964909971710.1038/nature07719ReinaA.JiaX.HoJ.NezichD.SonH.BulovicV.DresselhausM. S.JingK.Large area, few-layer graphene films on arbitrary substrates by chemical vapor deposition20099130352-s2.0-6074910770610.1021/nl801827vSutterP. W.FlegeJ.-I.SutterE. A.Epitaxial graphene on ruthenium2008754064112-s2.0-4254908958010.1038/nmat2166LiD.MüllerM. B.GiljeS.KanerR. B.WallaceG. G.Processable aqueous dispersions of graphene nanosheets2008321011052-s2.0-3894910862310.1038/nnano.2007.451ParkS.RuoffR. S.Chemical methods for the production of graphenes20094421722410.1038/nnano.2009.58StankovichS.DikinD. A.PinerR. D.KohlhaasK. A.KleinhammesA.JiaY.WuY.NguyenS. T.RuoffR. S.Synthesis of graphene-based nanosheets via chemical reduction of exfoliated graphite oxide2007457155815652-s2.0-3424974246910.1016/j.carbon.2007.02.034TungV. C.AllenM. J.YangY.KanerR. B.High-throughput solution processing of large-scale graphene20094125292-s2.0-5814921843010.1038/nnano.2008.329ZhangJ.YangH.ShenG.ChengP.ZhangJ.GuoS.Reduction of graphene oxide vial-ascorbic acid2010467111211142-s2.0-7624910664710.1039/b917705aChenL. C.TienC. H.FuC. S.Magneto-optical characteristics of Mn-doped ZnO films deposited by ultrasonic spray pyrolysis201215808510.1016/j.mssp.2011.04.003LawM.GreeneL. E.JohnsonJ. C.SaykallyR.YangP.Nanowire dye-sensitized solar cells2005464554592-s2.0-2014436963410.1038/nmat1387BaxterJ. B.AydilE. S.Nanowire-based dye-sensitized solar cells200586505311410.1063/1.1861510Du PasquierA.ChenH.LuY.Dye sensitized solar cells using well-aligned zinc oxide nanotip arrays200689252-s2.0-3384596437810.1063/1.2420779253513ChengH.-M.ChiuW.-H.LeeC.-H.TsaiS.-Y.HsiehW.-F.Formation of branched ZnO nanowires from solvothermal method and dye-sensitized solar cells applications20081124216359163642-s2.0-5564909924710.1021/jp805239kGonzalez-VallsI.Lira-CantuM.Vertically-aligned nanostructures of ZnO for excitonic solar cells: a review20092119342-s2.0-6924912383210.1039/b811536bMartinsonA. B. F.ElamJ. W.HuppJ. T.PellinM. J.ZnO nanotube based dye-sensitized solar cells200778218321872-s2.0-3454815505710.1021/nl070160+MartinsonA. B. F.GoesM. S.Fabregat-SantiagoF.BisquertJ.PellinM. J.HuppJ. T.Electron transport in dye-sensitized solar cells based on zno nanotubes: evidence for highly efficient charge collection and exceptionally rapid dynamics200911316401540212-s2.0-6554909110910.1021/jp810406qJiangC. Y.SunX. W.LoG. Q.KwongD. L.WangJ. X.Improved dye-sensitized solar cells with a ZnO-nanoflower photoanode200790262-s2.0-3454736603510.1063/1.2751588263501HosonoE.FujiharaS.HonmaI.ZhouH.The fabrication of an upright-standing zinc oxide nanosheet for use in dye-sensitized solar cells20051717209120942-s2.0-2464446963510.1002/adma.200500275HosonoE.MitsuiY.ZhouH.Metal-free organic dye sensitized solar cell based on perpendicular zinc oxide nanosheet thick films with high conversion efficiency20082840543954412-s2.0-5344909737210.1039/b800907dKaidashevE. M.LorenzM.von WencksternH.RahmA.SemmelhackH.-C.HanK.-H.BenndorfG.BundesmannC.HochmuthH.GrundmannM.High electron mobility of epitaxial ZnO thin films on c-plane sapphire grown by multistep pulsed-laser deposition20038222390139032-s2.0-003864629110.1063/1.1578694WangC.-C.YingJ. Y.Sol-gel synthesis and hydrothermal processing of anatase and rutile titania nanocrystals19991111311331202-s2.0-0000383003CzerwR.FoleyB.TekleabD.RubioA.AjayanP. M.CarrollD. L.Substrate-interface interactions between carbon nanotubes and the supporting substrate200266153340813340842-s2.0-0037101158033408AnderssonA.JohanssonN.BrömsP.YuN.LupoD.SalaneckW. R.Fluorine tin oxide as an alternate to indium tin oxide in polymer LEDs199810118598632-s2.0-0032479696KongkanandA.DomínguezR. M.KamatP. V.Single wall carbon nanotube scaffolds for photoelectrochemical solar cells. Capture and transport of photogenerated electrons2007736766802-s2.0-3404712656310.1021/nl0627238XuF.ChenJ.WuX.ZhangY.WangY.SunJ.BiH.LeiW.NiY.SunL.Graphene scaffolds enhanced photogenerated electron transport in ZnO photoanodes for high-efficiency dye-sensitized solar cells201311717861986272-s2.0-8487701126010.1021/jp312379b