Journal of Spectroscopy

Volume 2013 (2013), Article ID 164275, 4 pages

http://dx.doi.org/10.1155/2013/164275

Research Article

The In Situ Polymerization and Characterization of PA6/LiCl Composites

Dandan Sun, Jiang Li, Qinghua Pan, Chaowei Hao, and Guoqiao Lai

Key Laboratory of Organosilicon Chemistry and Material Technology Ministry of Education, Hangzhou Normal University, Hangzhou 310012, China

Received 5 October 2013; Accepted 23 November 2013

Academic Editor: Yizhuang Xu

Copyright © 2013 Dandan Sun et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

PA6/LiCl composites were synthesized by in situ anionic polymerization based on the interaction between the inorganic salts and PA6. Sodium hydroxide as initiator and N-acetylcaprolactam as activator were used in the preparation of PA6/LiCl composites with variety of LiCl content. X-ray diffraction (XRD) and differential scanning calorimeter (DSC) testing results showed that both of degree of crystallinity and melting temperature of the composites were decreased under the influence of LiCl. And the γ crystal phase proportion increased with increasing the LiCl content to appropriate amount.

1. Introduction

Polyamide is general thermoplastic resin with repeat amide groups—[NHCO]—on the molecular main chain, and it is commonly known as nylon. PA6 is a very common and important polymer material used in different fields ranging from textile and carpet production to special technical applications. The intramolecular polar amide group of PA6 can be found in hydrogen bond, increasing the intermolecular forces, and exhibiting relatively high strength, good toughness, chemical and abrasion resistance, and so forth. Nowadays, superfine fibers have attracted more and more attention from people for occupying the special properties, and the research on the superfine fibers is developing quickly [1]. However, the plenty of hydrogen bonding between chains in PA6, quickly crystal capacity, high crystallinity, and chain defects in the crystal lattice restrict the molecular arrangement and orientation, which hinders the achievement of higher DR during the PA6 spinning and the processing of the superfine fiber.

The studying emphasis of PA6 is always focusing on the modification in order to change the properties of polymer and be suitable for more applications [2–5]. There are many modification methods, which in general can be divided into blending, in situ polymerization, and copolymerization. As for in situ polymerization of PA6 composite, the acquired composites are prepared by adding the modifier (polymer or inorganic particles) to the caprolactam molten monomer, then adding sodium hydroxide as initiator to open the ring, and introducing N-acetylcaprolactam as activators to a high-polymerization rate [6, 7]. This paper introduced the modification of PA6 and prepared a series of PA6/lithium chloride composite via in situ anionic polymerization. The characterization of the composites was carried out by FT-IR, NMR, DSC, and X-ray analysis methods.

2. Materials and Methods

2.1. Materials

Caprolactam, AR, Aladdin Chemistry Co., Ltd.; Sodium hydroxide, AR, Aladdin Chemistry Co., Ltd.; lithium chloride, AR, Tianjin University Chemical Reagent Factory; acetic anhydride, Shanghai Lingfeng Chemical Reagent Co., Ltd.

2.2. The Preparation of N-Acetylcaprolactam (CCL)

N-Acetylcaprolactam can increase the electronegativity of amido bond and improve the amide carbonyl activity of caprolactam anion. Toluene was used as solvent in the preparation; the ratio of acetic anhydride and caprolactam was 1.2 : 1, then heating reflux for 2 h and extracting the unreacted acetic anhydride and the acetic acid with distilled water. The synthesis of CCL was shown in Scheme 1.

Scheme 1: Synthesis of N-acetylcaprolactam.

2.3. Synthesis of LiCl/PA6 Composites

Lithium chloride which acted as modifier can interact with carbonyl group in caprolactam monomer and dissolve into the monomer, which means the well dispersed of modifier in the polymer composites. The experimental process was as follows: firstly, adding certain amount of caprolactam in a three-flask bottle and heating to 130°C under vacuum for 30 minutes to remove moisture and impurity in the system; secondly, quickly putting certain amount of lithium chloride into the bottle, keeping up the vacuum, and heating to 135°C at the same time until lithium chloride dissolved completely; thirdly, adding catalyzer sodium hydroxide into the melt mixture and heating to 140°C; fourthly, after catalyzing for 15 minutes, adding the activator (CCL) into the bottle fast; finally, pouring the melt mixture into a mold preheated at 180°C until the polymerization finished.

3. Results and Discussion

3.1. The Characterization of N-Acetylcaprolactam (CCL)

The products were characterized by FT-IR and NMR, as shown in Figures 1 and 2. ¹H-NMR (CDCL₃, δ): 2.49 (S, 3H, –CH3), 2.73 (T, 2H, –CH2–), 3.89 (T, 2H, –CH2–); IR (cm⁻¹, film) 2933 (–CH2–), 1696 (C=O).

Figure 1: FT-IR spectrum of N-acetylcaprolactam.

Figure 2: ¹H-NMR spectrum of N-acetylcaprolactam.

3.2. XRD Analysis of PA6/LiCl Composite

PA6 was a multicrystal phase polymer; the crystallization behavior including crystallinity, crystal structure, size, and distribution of spherulite had decisive influence on the physical properties of nylon product. As a result, controlling the appropriate crystalline state was very important for PA6 product to obtain excellent performance. Under different crystallization conditions, different formation of the hydrogen bond structure forming is different, which led to different spherulite structure. PA6 mainly had two stable crystal structures α and γ [8], γ-form can improve the degree of deformation, and α-form has strong stability. During PA6 spinning process, γ-form could improve the deformation degree and benefit to prepare the superfine denier fiber.

The XRD patterns in Figure 3 showed that the samples of PA6 and the composites displayed characteristic peaks at scattering angles of 20.0° and 23.60° [9], corresponding to the reflections of the crystalline planes (200) and combined (002)/(202), respectively, which was corresponding to monoclinic α-phase morphology. The peak position of the composites had a slight displacement compared with PA6, which implied that the lattice dimension of PA6 changed with the addition of lithium chloride. It was interesting that the composite had obvious diffraction peak at about 21.4°, which corresponded to the γ-form of PA6.

Figure 3: Wide angle X-ray diffraction patterns of LiCl/PA6 composites with different LiCl content: (1) 0.0%; (2) 0.1%; (3) 0.3%; (4) 0.5%; (5) 1.0%; (6) 2.0%.

As can be seen from Table 1, compared with pure PA6, both the two diffraction angles in PA6/LiCl composites became larger, which could be due to the destruction effect of lithium chloride molecule on the hydrogen bonding between the PA6 chains. Comparing the proportion of α-form of PA6 and the composites, we could find that the content of α-form reduced with increasing content of lithium chloride. Variation trend of the γ-crystal form also can be seen from Figure 3. With increasing content of lithium chloride, the intensity of γ-form crystal diffraction peak increased first and then decreased, which illustrated that the proportion of PA6 γ-form crystal phase increased with lithium chloride content increasing in a certain range.

Table 1: The XRD parameters of the PA6/LiCl composites.

Sample
HKL
2θ/°

αl/α2 (%)
γ/α (%)

0%
200
20.3
620.5
48.6
6.7

100
21.8
126.4

23.5
1276.0

0.1%
200
20.3
453.3
34.2
11.9

100
21.6
213.0

23.6
1327.1

0.3%
200
20.2
268.1
90.0
31.2

100
21.4
176.5

23.6
297.7

0.5%
200
20.3
99.0
30.7
40.6

100
21.6
171.1

23.7
322.2

1.0%
200
20.4
581.8
70.9
12.2

100
21.8
171.2

23.8
820.7

3.3. DSC Analysis of PA6/LiCl Composite

Figure 4 showed the heating curves after erasing thermal history of nylon and composites. In the process of constant heating rate, the melting temperature linear declined with the increasement of lithium chloride content. When the content reached 2%, the melting temperature declined to nearly 20°C compared with that of PA6. Both the pure PA6 and the PA6/LiCl composites had multiple melting peaks, which may be due to the different degree of crystallinity and crystal perfection. Higher temperature crystallization peak corresponded to a perfect crystal melting, while the low temperature peak was the low degree of crystal perfection [10, 11]. With the addition of lithium chloride, lithium ion could form six membered ring-structure via complexing interaction with PA6 molecule, which reduced molecular chain migration rate and the degree of crystal perfection.

Figure 4: The second heating process of the PA6/LiCl composites with different LiCl content: (1) 0.0%; (2) 0.1%; (3) 0.3%; (4) 0.5%; (5) 1.0%; (6) 2.0%.

4. Conclusions

We prepared the PA6/LiCl composites via in situ anionic polymerization. IR and NMR result confirmed the successful synthesis of N-acetylcaprolactam which acted as activator. DSC and X-ray results showed that the γ-crystal phase proportion in composites increased with increasing the LiCl content to appropriate amount. While γ-form could improve the degree of deformation, which implied that the preparation of superfine fiber for PA6 became easily during the spinning.

Acknowledgments

This work was financially supported by the Major Science and Technology Projects of Science and Technology Department of Zhejiang Province (Contract Grant no. 2010C11043) and funded by National High Technology Research and Development Program 863 (2010AA03A406).

References

R. Wang and D. S. Zhang, Process and Application of the Superfine Fibers, China Textile & Apparel Press, Zhejiang, China, 2007.

V. N. Dougnac, B. C. Peoples, and R. Quijada, “The effect of nanospheres on the permeability of PA6/SiO₂ nanocomposites,” Polymer International, vol. 60, no. 11, pp. 1600–1606, 2011.

C. Z. Liao and S. C. Tjong, “Mechanical and thermal behaviour of polyamide 6/silicon carbide nanocomposites toughened with maleated styrene-ethylene-butylene-styrene elastomer,” Fatigue and Fracture of Engineering Materials and Structures, vol. 35, no. 1, pp. 56–63, 2012.

B. Huang, D. Li, Z. Li, X. Li, and W. Zhou, “Reactive compatibilization of PA 6/ABS blends by ethylene-acrylate-glycidyl methacrylate copolymer,” Journal of Applied Polymer Science, vol. 122, no. 1, pp. 586–592, 2011.

G. Rusu and E. Rusu, “Anionic nylon 6/TiO₂ composite materials: effects of TiO₂ filler on the thermal and mechanical behavior of the composites,” Polymer Composites, vol. 33, no. 9, pp. 1557–1569, 2012.

O. Monticelli, S. Bocchini, A. Frache, E. S. Cozza, O. Cavalleri, and L. Prati, “Simple method for the preparation of composites based on PA6 and partially exfoliated graphite,” Journal of Nanomaterials, vol. 2012, Article ID 938962, 5 pages, 2012.

Z. Xu and C. Gao, “In situ polymerization approach to graphene-reinforced nylon-6 composites,” Macromolecules, vol. 43, no. 16, pp. 6716–6723, 2010.

H. Arimoto, M. Ishibashi, M. Hirai, et al., “Crystal structure of the γ form of nylon6,” Journal of Polymer Science, vol. 3, no. 1, pp. 317–326, 1965.

M. I. Kohan, Nylon Plastics Handbook, Hanser, New York, NY, USA, 1995.

S. Yue, W. Gong, N. Qi, B. Wang, W. Zhou, and Y. Zhu, “Effect of the dispersion of organic rectorite on the nonisothermal crystallization kinetics and melting behaviors of nylon 6 nanocomposites,” Journal of Applied Polymer Science, vol. 110, no. 5, pp. 3149–3155, 2008.

L. Cui, Q. Fu, C.-J. Chang, and J.-T. Yeh, “The effect of poly(vinyl alcohol) hydrolysis on the properties of its blends with nylon 6,” Polymer Engineering and Science, vol. 49, no. 8, pp. 1553–1561, 2009.