Study on Apparent Kinetic Prediction Model of the Smelting Reduction Based on the Time-Series

1 Engineering Research Center of Metallurgical Energy Conservation and Emission Reduction, Ministry of Education, Kunming University of Science and Technology, Kunming, Yunnan 650093, China 2 Department of Information Management, Oriental Institute of Technology, 58, Sec. 2, Sichuan Roa., Panchiao, Taipei 200, Taiwan 3 Faculty of Science, Kunming University of Science and Technology, Kunming, Yunnan 650093, China


Introduction
The complexities in smelting reduction process of iron and steel come from the interaction between the fluid dynamics and chemical kinetics mechanisms.The research direction has changed to how to establish hybrid kinetic model by combining fluid dynamics equations with chemical kinetics algebraic equations and taking factors at the level of microchemical reactions into consideration.Some macrokinetic parameters should be modeled, such as the volume of wind, differential pressure, and feed rate obtained by dynamic and real-time detection in the process .However, micro-kinetic parameters in chemical reaction process cannot be got by detection and identification online.The apparent reaction rate changes with the chemical reaction and fluid.In addition, the significance of its kinetic analysis is pretty obvious.Thus, the majority of research focuses on mathematical and physical model based on kinetics 1-4 .There are many uncertain factors affecting the apparent reaction rate.Moreover, a great difference exists between the physical model of smelting reduction and the unreacted-core model in the blast furnace.So its calculation model would not be accurate enough, even nonignorable errors exist 5 .One advantage of time-series analysis methods is to infer the future value from the historical value without considering other factors.Timeseries analysis methods are very convenient and accurate to study the evolution of apparent reaction rate.In this paper, time-series analysis methods are used to study the prediction model on the DTG data apparent reaction rate obtained by thermo gravimetric technique.It can be seen that the model has expressed the dynamic process of smelting reduction and has got high hit rate under uncertainty.Finally, the predicting method has been improved effectively.
The rest of the paper is organized as follows.In Section 2, the appropriate predicting method is employed to analyze the features of derivative thermo gravimetric data.The one-step forward local weighted linear method and its analysis and discussion of the experimental data are shown in Section 3. The EMD method and AR model for analyzing experimental data will be presented in Section 4; in the meanwhile, some improvement of the EMD-AR model is also provided.Finally, a brief summary is discussed in Section 5.

Features Analysis of Derivative Thermogravimetric Data
First, the features of DTG are analyzed.Correlation dimension, an important evidence to establish the existence of chaotic continuous systems, is calculated with the reconstruction map of the fractal dimension.For the truly random signals, the correlation dimension graph will look like a 45-degree straight line.It is indicating that no matter how you embed the noise, it will evenly fill that space.Chaotic or periodic signals have a distinct spatial structure, and their correlation dimension will saturate as some point while embedding dimension is increased.
The correlation dimension reaches saturation by calculating the correlation dimension of DTG data, as shown in Figure 1.It is shown that the nonlinear chaotic characteristics exist in the system.
In VRA visual recurrence analysis , we can construct such a model from a range of classes, such as nearest neighbor, locally constant, kernel regression, locally linear, locally weighted linear, radial basis models, and support vector regression 6-9 .Then, the appropriate predicting method is selected.In general, the methods of predicting chaotic time-series include multistep and one-step.One-step is better than multistep for the errors curve of DTG.Locally weighted linear method, one of the one-step methods, is superior to other methods for the errors' curve of DTG.

Prediction Analyses of One-Step Forward Locally
Weighted Linear Method

Locally Weighted Linear (LWL) Method
With a given time-series {x 1 , x  One-step estimate is generated by where d is the embedding dimension and t is time delay.Suppose X The weight of X i is defined by where K • is essentially a weighting function used to assign the contribution of each neighbor to the prediction in locally weighted linear predictor and d i is the distance between X and X i .The Gaussian kernel function is to be used here, which is calculated in the following: where distance is the Euclidean distance.
The locally weighted linear methods can be expressed in

Mathematical Problems in Engineering
The situation that the embedding dimension is one m 1 was discussed; others m > 1 are similar: The weighted least squares method is applied to 3.5 , which can be demonstrated as Then partial derivatives of a or b are as follows:

3.7
Solutions are expressed in

3.8
Taking a, b into x n 1 a bx n , then, the predicted value was got.
x n 1

3.9
The calculated performance is otherwise known as the root mean square error RMSE and the normalized mean squared error NMSE .NMSE increased the role of large-value where p i is the predictive value and a i is the real value.Based on 3.11 , the smaller NMSE is from the predicted values and actual values.The predictions are quite accurate, and the NMSE for the prediction of 200 points is only 0.8771.That means our predictive model explains about 99.123% of the variance in the series.

Results and Discussion
Derivative thermogravimetric data of the Huimin ore reflect the change of the apparent reaction rate in the smelting reduction process.Experiment extent is confirmed with bases 0.8, 1.1, 1.4, 1.7, 2.0; respectively, the compositions of each type of materials required are shown in Table 1.
The TGA experiment equipment is produced by Netzsch, modeling as STA 449 F3.It is protected with nitrogen gas flowing at 50 mL/min.And argon, acting as purge gas, flows at the rate of 10 mL/min.There are 200 points around 1400 • C predicted.The performances of their prediction charts using one-step forward locally weighted linear method are shown in Figure 2.
From Figure 2, the prediction is well matched, especially in the trend of rise or decline.It is shown that RMSE remains at about 0.1, and the error is small and stable in Table 2; in the meanwhile, NMSE is maintained at about 0.9, which explains more than 99% of the variance.

Prediction Analysis of Derivative Thermogravimetric Data of the EMD-AR Method
Empirical mode decomposition EMD has been successfully applied to many fields, such as communication, society, economy, engineering, and achieved good effects 12-19 .The AR model forecasting methods is intended to apply to the system of smelting reduction.

Empirical Mode Decomposition
EMD method is developed from the simple assumption that any signal consists of different simple intrinsic modes of oscillations.Each linear or nonlinear mode will have the same number of extreme and zero crossings.There is only one extreme between successive zerocrossings.Each mode should be independent of the others.In this way, each signal could be decomposed into a number of intrinsic mode functions IMFs , each of which must satisfy the following definitions 15 .
a In the whole data set, the number of extreme and the number of zero-crossings must either equal or differ from each other at most by one.
b At any point, the mean value of the envelope defined by local maxima and the envelope defined by the local minima is zero.
An IMF represents a simple oscillatory mode compared with the simple harmonic function.
With the definition, any signal x t can be decomposed as follows.
1 Identify all local extremes, and then connect all the local maxima by a cubic spline line as the upper envelope.
2 Repeat the procedure for the local minima to produce the lower envelope.The upper and lower envelopes should cover all the data among them.
3 The mean of upper and low envelope value is designated as m 1 , and the difference between the signal x t and m 1 is the first component, h 1 ; that is, Generally speaking, h 1 will not necessarily meet the requirements of the IMF, because h 1 is not a standard IMF.It needs to be selected for k times until the mean envelope tends to zero.Then the first intrinsic mode function c 1 is denoted, which stands for the most high-frequency component of the original data sequence.At this point, the data could be represented as where h 1k is the datum after k times' siftings.h 1 k−1 stands for the datum after k − 1 times' sifting.Standard deviation SD is used to determine whether the results of each filter component meet the IMF or not.SD is defined as where T is the length of the data.The value of standard deviation SD is limited in the range of 0.2 to 0.3, which means that when 0.2 < SD < 0.3, the decomposition process can be finished.The physical considerations of this standard are the following: it is necessary to not only ensure h k t to meet the IMF requirements but also control the decomposition times.So in this way the IMF components could retain amplitude modulation information in the original signal.
4 When h 1k has met the basic requirements of SD on the condition of c 1 h 1k , the signal x t of the first IMF component c 1 would be gotten and a new series r 1 could be achieved after deleting the high-frequency components.That is to say The new sequence is treated as the original data, and repeat the above 3.1 -3.3 processes.Then the second intrinsic mode function c 2 could be got.5 Repeat 3.1 -3.4 until r n will no longer be decomposed into the IMF.The sequence r n is called the remainder of the original data x t .r n is a monotonic sequence, indicating the overall trend of the raw data x t or mean, which is usually referred as the so-called trend items.It is of clear physical significance.
The process is expressed as follows Then, The original data can be expressed as the IMF component and remainder.
The rate trend characterized by five kinds of base after EMD decomposition is shown in Figure 3.
Seen from Figure 3, the experimental data are divided into 13 groups.The last group is a trend term and parabolic curve, indicating there is an inner maximum of the apparent reaction rate existing in the unsteady-state process.And the temperature ranges from 600 to 800 • C; when the temperature falls in this range, various crystalline phases of iron oxides change, but the mass will not change much 20 .

AR Model
Equation 4.7 is a p step autoregressive model, referring as AR p model 21 .Stationary time-series {X t } that meets the model AR p is called the AR p sequence.That a a 1 , a 2 , . . ., a p T is named as the regression coefficients of the AR p model.

Modified EMD-AR Method
Huimin ore was analyzed with different base at sampling points of 8144, after the decomposition of EMD, the data can be divided into 13 groups, and the last group is a trend term.Firstly, each component is tried out through the ADF stationary test, as can be seen from Table 3; 1%, 5%, 10% of the values are greater than the level of ADF critical value, which is no unit root.So it can be said to meet the stationary time-series.From Table 4, according to the geometric decay of the correlation coefficient and partial correlation coefficients fourthorder truncation, it can be regarded as AR 3.4 model.After the analyses of 13 groups, the majority are positioned in AR 3.4 .For simplicity, AR 3.4 model should be taken into account.
Then with the previous 7944 data points, each group of data is predicted to 8144 in the method of AR 3.4 model.
Calculation results are represented in where x n−j,i is the autoregressive variable of the ith component.a n−j,i is the corresponding self-group regression coefficients.Equation 4.9 is revised by the golden section weighting: x n 1 0.618x n 1 0.382x n .4.9

Analysis and Comparison of Experimental Results
The results calculated by using MATLAB programming are shown in Figure 4.
As can be seen from Figure 4, the trend match is quite well.The overall hit rate is also high, reaching a basic agreement.In Tables 3 and 4, the steadiness can be determined by the decay of autocorrelation and 4 steps truncated of partial autocorrelation, so the fourthstep autoregressive model is taken into account.The chaotic time-series are generally nonstationary, even after repeated differential data cannot be stationary.It is shown that the EMD can compensate the deficiency of nonsteadiness.Prediction performance is poorer when adding white noise disturbance than those without noise, and the deterministic signal is comparatively evident.The model of golden weighted correction is better.The result of error analysis is shown in Table 5.
Based on Table 5, RMSE of EMD-AR method has decreased about two-thirds than the local linear weighting method.NMSE decreased in an order of magnitude.The improved EMD-AR error is smaller.The average error AE is also very small, especially minimum errors of R 1.1 and 1.4,where reduction effort was better 22 .In Figure 5, it is obviously shown the characteristic of the normal distribution for DTG data, which reflect the ergodicity of the apparent reaction rate in the smelting process; Figure 6 further clearly demonstrates the statistical laws of DTG, there exists the pair of "∞" curves including internal ∞ curve and external ∞ curve, resp., and many scattered points distribute around the curves.So it can be concluded that it belongs to the random discrete dynamic system, and it will be the breakthrough in the curve equation research.which shows that the method is better; this can also be seen by the errors' data itself.The evolution model of the apparent rate is expressed much more clearly.

Conclusion
2 EMD-AR 3.4 steps have been derived from the data stationary test analysis and autocorrelation and partial correlation coefficient.It is shown that the RMSE of the EMD-AR method has decreased two-thirds than local linear weighting method;  NMSE decreased in an order of magnitude.Error of using improved EMD-AR method is smaller; the average error AE is also very small, especially minimum errors of R 1.1 and 1.4 where reduction effect is better.It is shown that golden weighted correction to EMD-AR method is effective.

Figure 2 :
Figure 2: Prediction effect for different values of R.

Table 1 :
Compositions of each type of materials required.
errors in the indicators, thereby improved the sensitivity of this indicator.Equations 3.10 and 3.11 are using one-step prediction:

Table 4 :
lists autocorrelation and partial autocorrelation.