Mathematical Problems in Engineering

Volume 2013 (2013), Article ID 230413, 12 pages

http://dx.doi.org/10.1155/2013/230413

Research Article

State-Feedback Sampled-Data Control Design for Nonlinear Systems via Passive Theory

Chengming Yang,¹ Qi Zhou,² H. R. Karimi,³ and Huanqing Wang⁴

¹College of Engineering, Bohai University, Jinzhou, Liaoning 121013, China

²College of Information Technology and Science, Jinzhou, Liaoning 121013, China

³Department of Engineering of the Faculty of Engineering and Science, University of Agder, 4898 Grimstad, Norway

⁴School of Mathematics and Physics, Bohai University, Jinzhou, Liaoning 121013, China

Received 30 August 2013; Accepted 6 September 2013

Academic Editor: Zhiguang Feng

Copyright © 2013 Chengming Yang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

This paper investigates the problem of passive controller design for a class of nonlinear systems under variable sampling. The Takagi-Sugeno (T-S) fuzzy modeling method is utilized to represent the nonlinear systems. Attention is focused on the design of passive controller for the T-S fuzzy systems via sampled-data control approach. Under the concept of very-strict passivity, a novel time-dependent Lyapunov functional is constructed to develop passive analysis criteria and passive controller synthesis conditions. A new sampled-data controller is designed to guarantee that the resulting closed-loop system is very-strictly passive. These conditions are formulated in the form of linear matrix inequalities (LMIs), which can be solved by convex optimization approach. Finally, an application example is given to demonstrate the feasibility and effectiveness of the proposed results.

1. Introduction

Recently, it is well known that the fuzzy logic control [1–6] is one of effective approaches to handle complex nonlinear systems and has some applications in various real systems. It is well known that the Takagi-Sugeno (T-S) [7] fuzzy model has become a popular and effective method to control complex nonlinear systems. T-S fuzzy model is described as a weighted sum of some simple linear subsystems and thus are easily analyzable. During the past few decades, the problem of stability analysis and controller synthesis of nonlinear systems in Takagi-Sugeno (T-S) [7–10] fuzzy model has been extensively studied and some stability analysis and controller synthesis results have been reported, see, for instance, [11–18] and the references therein. To mention a few, the book [11] proposed fuzzy control systems design and analysis results via linear matrix inequality (LMI) approach [19–26] and the paper [12] presented a survey on the state-of-the-art and recent developments of the art of analysis and design of model-based fuzzy control systems. In addition, due to the effect of time delay in systems, the study of T-S fuzzy systems with time delays has received considerable attention in recent years and the results have been developed in [27–35]. The authors in [35] dealt with the problem of reliable fuzzy controller design for uncertain active suspension systems with actuator delay and fault.

In practical control systems, it is important to investigate the controller design problem for sampled-data systems [36, 37]. Recently, the researchers in [38–43] discussed two main methods to develop stability analysis and control synthesis for sampled-data systems. The first one is to model a sampled data system as a discrete-time system [44], in which a sampled data system with a delay is modeled as a discrete-time system and a stability condition is derived. However, it should be mentioned that this method is very difficult to analyze or synthesize for complex systems. The second one is a delayed control input method by modeling the sampled-data system as a continuous-time system with a delayed control input, which was proposed in [41] and later used in [42, 45]. More recently, many sampled-data analysis and synthesis results have been reported for T-S fuzzy systems [46–50]. Among these results, the state-feedback control design method has been used in [47–51] and observed-based control approach has been used in [46]. Using input delay approach, the stabilization of nonuniform sampling fuzzy control systems have been investigated in [48–52], where the systems are regarded as ordinary continuous-time systems with a fast-varying delay. The authors in [51] used the time-dependent delay Lyapunov-Krasovskii functional idea [42] and introduced some slack matrices to improve the sampled-data control results about stabilization for fuzzy systems [48, 52]. However, these slack matrices may lead to a significant increase in the computational demand.

The passive properties of a system can keep the system internally stable and is frequently used in control systems to prove the stability of systems. There are extensive applications for passivity problem in various engineering areas such as electrical circuits, complex networks, mechanical systems, and nonlinear systems. The problems of passivity analysis and passive control have been extensively applied in many areas such as signal processing, fuzzy control, sliding mode control [53], and networked control systems [54]. More recently, the passive control problem has been studied for fuzzy systems [55–57]. In [57], the authors considered the passive control problems for a class of continuous-time T-S fuzzy systems with both state and input delays. The state-feedback fuzzy controller was designed such that the resulting closed-loop system is very-strictly passive. To the best of the authors’ knowledge, so far no attempt has been made towards solving the problem of passive control design results for nonlinear systems with variable sampling. This problem still remains challenging, which motivates this study.

In this paper, the passive controller design problem is investigated for a class of nonlinear systems under variable sampling. Firstly, the T-S fuzzy model is employed to represent the nonlinear systems. By using the input delay approach, the T-S fuzzy system with variable uncertain sampling is transformed into a continuous-time T-S fuzzy system with a delay in the state. Secondly, by constructing a novel time-dependent Lyapunov functional, under the concept of very-strict passivity, new passive analysis criteria are proposed and then novel sampled-data controller is designed to guarantee that the resulting closed-loop system is very-strictly passive. The existence conditions of the obtained controller can be expressed as linear matrix inequalities (LMIs), which can be solved using standard numerical software. Finally, an application example is given to illustrate the feasibility and effectiveness of the proposed passive control approach. The remainder of this paper is organized as follows. The problem to be solved is formulated in Section 2. Main results, including passive analysis and passive controller design are presented in Section 3. Section 4 provides an illustrative example to show the effectiveness and potential of the proposed design techniques. We conclude this paper in Section 4.

Notation. The notation used throughout the paper is fairly standard. The notation (resp., ), for means that the matrix is real symmetric positive definite (resp., positive semidefinite). Identity matrices, of appropriate dimensions, will be denoted by . If not explicitly stated, all matrices are assumed to have compatible dimensions for algebraic operations. The symbol “*” in a matrix stands for the transposed elements in the symmetric positions. The superscripts “” and “” denote the matrix transpose and inverse, respectively.

2. Problem Formulation

In this paper, we consider the following nonlinear system:

where is the state, denotes the control input, and is a known nonlinear continuous function and satisfies . In order to consider the passive controller design problem, under the concept of sector nonlinearity, the nonlinear system in (1) can be represented by the following T-S fuzzy systems.

Plant Rule . If is and is , then

where is the control output and is the disturbance input. , , , , , and are system matrices with appropriate dimensions. , the scalar is the number of IF-Then rules. and are the premise variable and the fuzzy set, respectively, . The defuzzified output of system (2) is inferred as follows:

where , , and is the degree of the membership of in fuzzy set . In this paper, we assume that for and for all . Therefore, (for ) and Suppose that the updating signal successfully transmitted signal from the sampler to the controller and to the Zero-Order Hold (ZOH) at the instant . We assume that the sampling intervals are bounded

Here denotes the maximum time span between the time at which the state is sampled and the time at which the next update arrives at the destination. The initial conditions of and are given as and for , where is a differentiable function. Similar to the fuzzy model, the same fuzz rule is used to construct the following overall fuzzy control law:

where denotes the th sampling instant, , and . are the local control gains and is the next updating instant time of the ZOH after . Denote for . It is clear that . It can be seen that is sawtooth structure, that is, piecewise-linear with derivative ,  . Then, from (5), we have

Then, substituting (6) into (3) yields

where and stand for and , respectively.

In order to develop the main results in the next section, the following definition is introduced.

Definition 1 (see [58]). Consider the following.

(D1) System (7) is said to be passive if there exists constant such that

 holds for all .(D2) System (7) is said to be strictly passive if there exist constants and such that

 holds for all .(D3) System (7) is said to be output strictly passive if there exist constants and such that

 holds for all . System (7) is said to be very-strictly passive if there exist constants , and such that

 holds for all .

The main objective of this paper is to give the novel sampled-data control conditions for T-S fuzzy system in (7) via passive control method. The controller is designed to guarantee that the resulting closed-loop system is very-strictly passive.

2.1. Main Results

This section focuses on designing the passive controller for fuzzy system (7). Firstly, the passivity analysis criterion is established for system (7) in the following theorem.

Theorem 2. Consider system in (7), for given constant and matrix , system (7) is very-strictly passive if there exist scalars ,  , matrices , ,  , , and with appropriate dimensions, such that the following LMIs hold for ,

where

Proof. Now, define a Lyapunov-Krasovskii function for system (7) as follows:

where , , and , , . It can be found that the term vanishes after the jumps because . Hence and is continuous in time. The time-derivative of , , and can be obtained as

From the condition in (14), we have . According to Jensen’s inequality and the second term in , we can have the following inequalities:

where

Similarly, for the first term in , we can have the following inequalities,

where

For the last term in , it can be found that

In addition,

Then, we establish the passivity analysis performance of system in (7),

where

It follows from Theorem 2 and ; it is derived that

Integrating both sides of (26) yields

where . Then, it can be seen from Definition 1 that system (7) is very-strictly passive. The proof is finished.

Remark 3. In the proof of Theorem 2, we construct a new time-dependent and membership-dependent Lyapunov functional and use the advance methods to present the passivity analysis conditions, resulting in less number of slack variable being introduced in Theorem 2.

Based on the passivity analysis condition in Theorem 2, the controller is derived in the form of (6) for the system in (7).

Theorem 4. Consider system in (7), for given positive scalars , , , and , system (7) is very-strictly passive if there exist scalars ,  , matrices , , , and with appropriate dimensions, such that the following LMIs hold for ,

where

Then, the control gain matrix is .

Proof. Firstly, it can be seen that the two inequalities and hold for positive scalars and due to the following two inequalities:

Then, define the variables as , , , , and , and replace the terms and with and in (28) and (29). We perform congruence transformation to (28) and (29) by

respectively. We can see that the LMIs conditions in (12) and (13) hold. Therefore, all the conditions in Theorem 2 are satisfied. The proof is completed.

If the assumption is removed, which means that Lyapunov functional candidate (16) does not include the term . Similar to the proof of Theorems 2 and 4, we have the following corollaries.

Corollary 5. Consider system in (7), for given constant and matrix , system (7) is very-strictly passive if there exist scalars , , matrices , , and with appropriate dimensions, such that the following LMIs hold for ,

where

Corollary 6. Consider system in (7), for given positive scalars , , , and , system (7) is very-strictly passive if there exist scalars , , matrices , ,  ,  , and with appropriate dimensions, such that the following LMIs hold for ,

where

The control gain matrix is computed as .

3. Simulation Results

In this section, an application example is used to demonstrate the applicability of the controller design method proposed in this paper.

Example 7. Consider the problem of balancing and swing-up of an inverted pendulum on a cart. The equations of the pendulum motion are given by [4]:

where stands for the angle (in radians) of the pendulum from the vertical, denotes the angular velocity, and is the force applied to the cart (in newtons). m/ is the gravity constant, denotes the mass of the pendulum, stands for the mass of the cart, is the length of the pendulum, and . Here, we choose kg, kg, and m in simulations [3].

The control objective here is to balance the inverted pendulum for the approximate range through a sampled-data control approach. First, we represent the system in (38) by a two-rule Takagi-Sugenofuzzy model [39].

Plant Rule  1. If is 0, then

Plant Rule  2. If is , then

where

and (notice that when , the system is uncontrollable). Membership functions for Rules 1 and 2 are listed below:

and , where . Figure 1 shows the membership functions.

Figure 1: Membership functions of two rules.

In order to demonstrate the effectiveness of the proposed passive control design method, we consider the system in (38) and other parameters in system (2):

We choose the disturbance input . It can be calculated that , which means . Let

In Figure 2, it can be observed that decreases as the time increases, which means that there may not exist a scalar such holds for all . In addition, Figure 3 still holds that there may not exist a scalar such that , which means that the open-loop system is not passive in the sense of Definition 1, and it is not very-strictly passive. Figure 4 demonstrates that the open-loop system is not stable.

Figure 2: Response of of the open-loop system.

Figure 3: Response of of the open-loop system.

Figure 4: State response of the open-loop system.

In Theorem 4, letting , , , , , and , it can be found that the closed-loop system is very-strictly passive for the allowable upper bound of ms. The control gain matrices are listed below:

Under the control gain matrices in (45), Figure 5 plots the responses of for the closed-loop system, which means that there may exist a scalar such holds for all . In Figure 6, it can be seen that there may exist a scalar such that . Then, one can know that the closed-loop system is very-strictly passive under the control gain matrices in (45). In addition, Figure 7 shows that the closed-loop system is stable. The computed control inputs arriving at the ZOH are shown in Figure 8, in which we can see that the piecewise continuous holding behavior of the control inputs.

Figure 5: Response of of the closed-loop system.

Figure 6: Response of of the closed-loop system.

Figure 7: State response of the closed-loop system.

Figure 8: Control signal response of the closed-loop system

According to the above observation, these simulation results can demonstrate that the designed sampled-data controller meets the specified design requirements.

4. Conclusions

In this paper, the problems of passivity analysis and passive control have been investigated for nonlinear systems under variable sampling. By using the nonlinear sector method, the T-S fuzzy model was established to describe the nonlinear systems. Based on the input delay approach, the T-S fuzzy system with variable uncertain sampling was transformed into a continuous-time T-S fuzzy system with a delay in the state. By constructing a novel time-dependent Lyapunov functional, sampled-data controller was designed to guarantee that the resulting closed-loop system is very-strictly passive. The controller existence conditions were expressed as LMIs. This paper has taken into account the main characteristics of sampled-data systems via defining a novel time-dependent Lyapunov functional. An example has been included to demonstrate the advantages of the theoretic results obtained. This paper talks about passivity analysis and passive control for nonlinear systems under variable sampling. In order to achieve more practical oriented results, further work could be considered under data-driven (measurements) framework [59, 60]. The future topics, for example, control [61] and fault tolerant scheme [62] in the identical framework, seem more interesting from both academic and industrial domains.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

This work was partially supported by the National Natural Science Foundation of China under Grants (61304002, 61304003), the Program for Liaoning Excellent Talents in University (LR2013053), and the Education Department of Liaoning Province under the general project research Grant no. L2013424.

References

S. Tong and H.-X. Li, “Fuzzy adaptive sliding-mode control for MIMO nonlinear systems,” IEEE Transactions on Fuzzy Systems, vol. 11, no. 3, pp. 354–360, 2003.

S.-C. Tong, X.-L. He, and H.-G. Zhang, “A combined backstepping and small-gain approach to robust adaptive fuzzy output feedback control,” IEEE Transactions on Fuzzy Systems, vol. 17, no. 5, pp. 1059–1069, 2009.

S. Tong and Y. Li, “Observer-based fuzzy adaptive control for strict-feedback nonlinear systems,” Fuzzy Sets and Systems, vol. 160, no. 12, pp. 1749–1764, 2009.

Y. Li, S. Tong, and T. Li, “Adaptive fuzzy output feedback control of uncertain nonlinear systems with unknown backlash-like hysteresis,” Information Sciences, vol. 198, pp. 130–146, 2012.

H. Li, J. Yu, C. Hilton, and H. Liu, “Adaptive sliding mode control for nonlinear active suspension vehicle systems using ts fuzzy approach,” IEEE Transactions on Industrial Electronics, vol. 60, no. 8, pp. 3328–3338, 2013.

Y.-J. Liu, S. Tong, and C. Chen, “Adaptive fuzzy control via observer design for uncertain nonlinear systems with unmodeled dynamics,” IEEE Transactions on Fuzzy Systems, vol. 21, no. 2, pp. 275–288, 2013.

T. Takagi and M. Sugeno, “Fuzzy identification of systems and its applications to modeling and control,” IEEE Transactions on Systems, Man and Cybernetics, vol. 15, no. 1, pp. 116–132, 1985.

S.-G. Cao, N. W. Rees, and G. Feng, “Analysis and design of fuzzy control systems using dynamic fuzzy-state space models,” IEEE Transactions on Fuzzy Systems, vol. 7, no. 2, pp. 192–200, 1999.

S. G. Cao, N. W. Rees, and G. Feng, “H ∞ control of uncertain fuzzy continuous-time systems,” Fuzzy Sets and Systems, vol. 115, no. 2, pp. 171–190, 2000.

K. Tanaka, T. Hori, and H. O. Wang, “A multiple Lyapunov function approach to stabilization of fuzzy control systems,” IEEE Transactions on Fuzzy Systems, vol. 11, no. 4, pp. 582–589, 2003.

K. Tanaka and H. O. Wang, Fuzzy Control Systems Design and Analysis: A Linear Matrix Inequality Approach, John Wiley & Sons, New York, NY, USA, 2001.

G. Feng, “A survey on analysis and design of model-based fuzzy control systems,” IEEE Transactions on Fuzzy Systems, vol. 14, no. 5, pp. 676–697, 2006.

S. K. Nguang and P. Shi, “H ∞ fuzzy output feedback control design for nonlinear systems: an LMI approach,” IEEE Transactions on Fuzzy Systems, vol. 11, no. 3, pp. 331–340, 2003.

H. K. Lam, “Stabilization of nonlinear systems using sampled-data output-feedback fuzzy controller based on polynomial-fuzzy-model-based control approach,” IEEE Transactions on Systems, Man, and Cybernetics B, vol. 42, no. 1, pp. 258–267, 2012.

H. Dong, Z. Wang, D. W. C. Ho, and H. Gao, “Robust H ∞ fuzzy output-feedback control with multiple probabilistic delays and multiple missing measurements,” IEEE Transactions on Fuzzy Systems, vol. 18, no. 4, pp. 712–725, 2010.

L. Wu, X. Su, P. Shi, and J. Qiu, “Model approximation for discrete-time state-delay systems in the T-S fuzzy framework,” IEEE Transactions on Fuzzy Systems, vol. 19, no. 2, pp. 366–378, 2011.

M. Liu, X. Cao, and P. Shi, “Fault estimation and tolerant control for fuzzy stochastic systems,” IEEE Transactions on Fuzzy Systems, vol. 21, no. 2, pp. 221–229, 2013.

M. Liu, X. Cao, and P. Shi, “Fuzzy-model-based fault tolerant design for nonlinear stochastic systems against simultaneous sensor and actuator faults,” IEEE Transactions on Fuzzy Systems, 2012.

P. Gahinet, A. Nemirovskii, A. J. Laub, and M. Chilali, “The LMI control toolbox,” in Proceedings of the 33rd IEEE Conference on Decision and Control, vol. 3, pp. 2038–2041, IEEE, 1994.

X. Xie, S. Yin, H. Gao, and O. Kaynak, “Asymptotic stability and stabilisation of uncertain delta operator systems with time-varying delays,” IET Control Theory & Applications, vol. 7, no. 8, pp. 1071–1078, 2013.

T. Li, W. X. Zheng, and C. Lin, “Delay-slope-dependent stability results of recurrent neural networks,” IEEE Transactions on Neural Networks, vol. 22, no. 12, pp. 2138–2143, 2011.

H. Gao, T. Chen, and J. Lam, “A new delay system approach to network-based control,” Automatica, vol. 44, no. 1, pp. 39–52, 2008.

H. Li, H. Gao, and P. Shi, “New passivity analysis for neural networks with discrete and distributed delays,” IEEE Transactions on Neural Networks, vol. 21, no. 11, pp. 1842–1847, 2010.

H. Li, X. Jing, and H. Karimi, “Output-feedback based h-infinity control for active suspension systems with control delay,” IEEE Transactions on Industrial Electronics, vol. 61, no. 1, pp. 436–446, 2014.

B. Shen, Z. Wang, and Y. S. Hung, “Distributed H ∞-consensus filtering in sensor networks with multiple missing measurements: the finite-horizon case,” Automatica, vol. 46, no. 10, pp. 1682–1688, 2010.

B. Shen, Z. Wang, H. Shu, and G. Wei, “On nonlinear H ∞ filtering for discrete-time stochastic systems with missing measurements,” IEEE Transactions on Automatic Control, vol. 53, no. 9, pp. 2170–2180, 2008.

B. Chen, X. Liu, S. Tong, and C. Lin, “Guaranteed cost control of T-S fuzzy systems with state and input delays,” Fuzzy Sets and Systems, vol. 158, no. 20, pp. 2251–2267, 2007.

S. Xu and J. Lam, “Robust H ∞ control for uncertain discrete-time-delay fuzzy systems via output feedback controllers,” IEEE Transactions on Fuzzy Systems, vol. 13, no. 1, pp. 82–93, 2005.

C. Lin, Q.-G. Wang, T. H. Lee, and Y. He, LMI Approach to Analysis and Control of Takagi-Sugeno Fuzzy Systems with Time Delay, vol. 351 of Lecture Notes in Control and Information Sciences, Springer, Berlin, Germany, 2007.

C. Lin, Q.-G. Wang, and T. H. Lee, “Stabilization of uncertain fuzzy time-delay systems via variable structure control approach,” IEEE Transactions on Fuzzy Systems, vol. 13, no. 6, pp. 787–798, 2005.

B. Zhang and S. Xu, “Delay-dependent robust H ∞ control for uncertain discrete-time fuzzy systems with time-varying delays,” IEEE Transactions on Fuzzy Systems, vol. 17, no. 4, pp. 809–823, 2009.

B. Zhang, J. Lam, S. Xu, and Z. Shu, “Robust stabilization of uncertain T-S fuzzy time-delay systems with exponential estimates,” Fuzzy Sets and Systems, vol. 160, no. 12, pp. 1720–1737, 2009.

L. Wu and W. X. Zheng, “L ₂-L ∞ control of nonlinear fuzzy itô stochastic delay systems via dynamic output feedback,” IEEE Transactions on Systems, Man, and Cybernetics B, vol. 39, no. 5, pp. 1308–1315, 2009.

L. Wu, X. Su, P. Shi, and J. Qiu, “A new approach to stability analysis and stabilization of discrete-time T-S fuzzy time-varying delay systems,” IEEE Transactions on Systems, Man, and Cybernetics B, vol. 41, no. 1, pp. 273–286, 2011.

H. Li, H. Liu, H. Gao, and P. Shi, “Reliable fuzzy control for active suspension systems with actuator delay and fault,” IEEE Transactions on Fuzzy Systems, vol. 20, no. 2, pp. 342–357, 2012.

T. Chen and B. Francis, Optimal Sampled-Data Control Systems, Springer, London, UK, 1995.

R. Kalman, “Nonlinear aspects of sampled-data control systems,” in Proceedings of the Symposium on Nonlinear Circuit Analysis, vol. 6, pp. 273–313, 1956.

B. Bamieh, J. B. Pearson, B. A. Francis, and A. Tannenbaum, “A lifting technique for linear periodic systems with applications to sampled-data control,” Systems and Control Letters, vol. 17, no. 2, pp. 79–88, 1991.

T. Chen and L. Qiu, “H ∞ design of general multirate sampled-data control systems,” Automatica, vol. 30, no. 7, pp. 1139–1152, 1994.

S. K. Nguang and P. Shi, “Nonlinear H ∞ filtering of sampled-data systems,” Automatica, vol. 36, no. 2, pp. 303–310, 2000.

E. Fridman, A. Seuret, and J.-P. Richard, “Robust sampled-data stabilization of linear systems: an input delay approach,” Automatica, vol. 40, no. 8, pp. 1441–1446, 2004.

E. Fridman, “A refined input delay approach to sampled-data control,” Automatica, vol. 46, no. 2, pp. 421–427, 2010.

L.-S. Hu, T. Bai, P. Shi, and Z. Wu, “Sampled-data control of networked linear control systems,” Automatica, vol. 43, no. 5, pp. 903–911, 2007.

W. Zhang, M. S. Branicky, and S. M. Phillips, “Stability of networked control systems,” IEEE Control Systems Magazine, vol. 21, no. 1, pp. 84–97, 2001.

H. Gao, J. Wu, and P. Shi, “Robust sampled-data control with stochastic sampling,” Automatica, vol. 45, no. 7, pp. 1729–1736, 2009.

S. K. Nguang and P. Shi, “Fuzzy H ∞ output feedback control of nonlinear systems under sampled measurements,” Automatica, vol. 39, no. 12, pp. 2169–2174, 2003.

H. Katayama and A. Ichikawa, “H ∞ control for sampled-data nonlinear systems described by Takagi-Sugeno fuzzy systems,” Fuzzy Sets and Systems, vol. 148, no. 3, pp. 431–452, 2004.

H. Gao and T. Chen, “Stabilization of nonlinear systems under variable sampling: a fuzzy control approach,” IEEE Transactions on Fuzzy Systems, vol. 15, no. 5, pp. 972–983, 2007.

H. K. Lam and F. H. F. Leung, “Sampled-data fuzzy controller for time-delay nonlinear systems: fuzzy-model-based LMI approach,” IEEE Transactions on Systems, Man, and Cybernetics B, vol. 37, no. 3, pp. 617–629, 2007.

H. K. Lam, “Sampled-data fuzzy-model-based control systems: stability analysis with consideration of analogue-to-digital converter and digital-to-analogue converter,” IET Control Theory and Applications, vol. 4, no. 7, pp. 1131–1144, 2010.

X.-L. Zhu, B. Chen, D. Yue, and Y. Wang, “An improved input delay approach to stabilization of fuzzy systems under variable sampling,” IEEE Transactions on Fuzzy Systems, vol. 20, no. 2, pp. 330–341, 2012.

J. Yoneyama, “Robust H ∞ control of uncertain fuzzy systems under time-varying sampling,” Fuzzy Sets and Systems, vol. 161, no. 6, pp. 859–871, 2010.

L. Wu and W. X. Zheng, “Passivity-based sliding mode control of uncertain singular time-delay systems,” Automatica, vol. 45, no. 9, pp. 2120–2127, 2009.

H. Gao, T. Chen, and T. Chai, “Passivity and passification for networked control systems,” SIAM Journal on Control and Optimization, vol. 46, no. 4, pp. 1299–1322, 2007.

C. Li, H. Zhang, and X. Liao, “Passivity and passification of fuzzy systems with time delays,” Computers and Mathematics with Applications, vol. 52, no. 6-7, pp. 1067–1078, 2006.

J. Liang, Z. Wang, and X. Liu, “Robust passivity and passification of stochastic fuzzy time-delay systems,” Information Sciences, vol. 180, no. 9, pp. 1725–1737, 2010.

B. Zhang, W. X. Zheng, and S. Xu, “Passivity analysis and passive control of fuzzy systems with time-varying delays,” Fuzzy Sets and Systems, vol. 174, no. 1, pp. 83–98, 2011.

B. Brogliato, R. Lozano, B. Maschke, and O. Egeland, Dissipative Systems Analysis and Control: Theory and Applications, Communications and Control Engineering Series, Springer, London, UK, 2nd edition, 2007.

S. Yin, S. Ding, A. Haghani, H. Hao, and P. Zhang, “A comparison study of basic data-driven fault diagnosis and process monitoring methods on the benchmark Tennessee Eastman process,” Journal of Process Control, vol. 22, no. 9, pp. 1567–1581, 2012.

S. Yin, S. X. Ding, A. H. A. Sari, and H. Hao, “Data-driven monitoring for stochastic systems and its application on batch process,” International Journal of Systems Science, vol. 44, no. 7, pp. 1366–1376, 2013.

S. Yin, S. Ding, and H. Luo, “Real-time implementation of fault tolerant control system with performance optimization,” IEEE Transactions on Industrial Electronics, 2013.

S. Yin, X. Yang, and H. R. Karimi, “Data-driven adaptive observer for fault diagnosis,” Mathematical Problems in Engineering, vol. 2012, Article ID 832836, 21 pages, 2012.