Concrete box-girder bridges are widely used in China. During several routine inspections of two-year-old highway bridges of this type in the China Central Plains region, we found that transverse cracks are widespread on the bottom flanges of those box girders, mainly distributed in the area of 1/4

Concrete bridge structures are influenced by a variety of natural conditions where environmental thermal actions, such as solar radiation, ambient temperature, and wind, play major roles. Consequently, the temperature distribution varies and is changing all the time. The change is influenced by many factors, such as geographical location, solar radiation condition and intensity, and orientation of the structure and seasons. For concrete bridges, the heat exchange exists invariably on the structure surface through radiation, convection, and conduction. Since the heat exchange process is quite complex, a very complicated thermal load is formed [

At the beginning of the 1950s, the importance of thermal stress to concrete structures was recognized by research from the former Federal Republic of Germany when an on-site survey analysis of thermal stress of a concrete pier was carried out. Similar research was completed by the Major Bridge Engineering Group Corporation of the Chinese Ministry of Railways in the late 1950s and by others around the world. In the early days of temperature-induced stress research, only the temperature variations of the year were considered. With the progress of the experiment and theoretical study, people started to realize that thermal distribution in the concrete structure was a nonlinear question. By the 1950s, based on the conclusion of Stephenson from Great Britain, engineers started to consider the temperature difference between sun and shade.

With its long-span capability, good bearing performance, and convenient installation, prestressed concrete (PC) continuous box-girder bridges have been widely used in bridge design since the 1960s in China. But during the construction or the operation phases, many serious cracks were found on bridges in China and in other countries as well. Fritz Leonhardt mentioned in his study that the range of temperature differences between the upper limb and lower edge could be 27°C to 33°C when measured on box-girder and rib girder bridges. Most cracks on prestressed concrete box-girder bridges were caused by thermal stress. Mirambell and Aguado briefly presented an analytical model to predict temperature and stress distributions [

In the past, researchers concentrated on the temperature difference in sunlight when the study of thermal stress in concrete box-girder bridges was conducted. Although it is more difficult to analyze sunlight temperature distribution because of its complexity and rapid change, there is a lot of achievements in this field compared with the study of sudden temperature change. Relatively, the amount of research on thermal effect caused by sudden temperature change is not sufficient. As is commonly known, concrete is a nonperforming thermal conductivity material, so when the ambient temperature changes sharply, the outside temperature changes at nearly the same rate as the environment, but the internal temperature does not change as much. As a result, a large temperature gradient develops in box girders, and, meanwhile, deformation appears. If the deformation is restrained by material fiber and boundary conditions, it will produce thermal stress. But based on current research, a conclusion cannot be reached as to what kind of damage it will cause and whether or not it will lead to cracks on reinforced concrete (RC) and PC bridges.

Geometric nonlinearity is one of the most important topics in civil engineering, mechanical engineering, hydraulic engineering, aviation, and materials engineering. In the geometric nonlinear state, the strain-displacement relationship is nonlinear, and the large deformation makes the corresponding problems difficult to solve [

As the finite element method has the more cumbersome step of meshing and the inaccuracy of solving specific problems, the meshless method came into being. In the meshless method, the computational domain is replaced by some discrete nodes, and there is no need to use elements or grids to interpolate field variables, and the relationship between nodes can be changed. This method can partially or completely eliminate the grid and get rid of the limitation of the elements. Therefore, the meshless method has caught more interest in the large deformation problem, crack growth problem, metal forming problem, and other special problems, without reconstructing the mesh [

This paper will focus on actual stress states in the reinforced concrete and prestressed concrete bridges while drastic temperature variation occurs. We have presented in the paper a suitable temperature distribution according to continuous observation on a box-girder bridge in central plains region of China. To analyze the temperature effect, we have built finite element models (FEM) and studied the temperature’s effect on the cause of cracks. Moreover, we have suggested feasible solutions to avoid the issues on the bridge related to the change of temperature. For example, over the last two decades and especially in recent times, smart materials have attracted immense interest and have been studied intensively worldwide by both intradisciplinary and multidisciplinary research groups [

With the rapid economic development in China, great progress in bridge construction has taken place. New bridges are designed and built on a continuous basis. Among them, a large proportion is box-girder bridges, mainly in concrete. Based on long-term routine bridge inspections, many cracks have been found on box-girder bridges, even if they were designed as prestressed concrete bridges with no crack allowance. Some of them are quite serious. Some of the example cracks are shown in Figures

Transverse cracks on the bottom of the slab.

Serious cracks on the bottom of the slab.

Due to numerous cracks at the bottom of girders, some bridges were strengthened, as shown in Figure

Bottom slabs strengthened.

In Yun Xing’s paper “Study on the Capability against Cracking of the Pre-Stressed Concrete Box-Girder Bridges from the Design Aspect,” he found that “live load should not be the main factor influencing the cracking of a long-span prestressed concrete continuous beam bridge” through analysis and comparison of three different span bridges. Because the thickness and overall rigidity of the concrete structure are large and compared with the dead load, the proportion of live load is small. Beyond vehicular load on the bridge, wind load and temperature load could also be factors. In the central plains region of China, wind power is not as strong as it is in other regions of China so its effect can be excluded. Therefore, the thermal load was speculated to be the main cause of this type of crack.

Thermal stress can be divided into two parts. The first part is called thermal self-restraint stress. The strain that the fiber undergoes in the internal concrete structure is not the same due to different temperatures between external and internal structures. Because of the mutual constraint between fibers, diverse strain leads to thermal self-restraint stress. The second part is called secondary thermal stress. Each component of the internal system deforms out of phase under different temperatures. These deformations are restricted by external constraints. Then, the secondary thermal stress comes into place. Thermal stress is practically nonlinear and sometimes the stress and strain do not obey Hooke’s law.

There are four main external factors that affect the temperature of the concrete structure, namely, (1) the hydration heat of cement, (2) the change of annual temperature, (3) sunlight, and (4) sudden changes in temperature. R. Springenschmid believes that 2/3 of the stress of concrete comes from temperature changes, and 1/3 comes from shrinkage and swelling. The heat of hydration of cement is the main source of early temperature stress of concrete, and temperature stress is a very important factor in the early cracking of concrete. Analyzing the temperature changed by cement hydration heat is complicated, but this heat can be regulated by controlling the construction temperature. Annual temperature change is somewhat an average temperature change for box girders caused by physioclimate. This change is slow, and its primary result is longitudinal displacement for a bridge. The displacement can be adjusted by the expansion joint or support displacement or set up by the flexible pier and so on to deal with the problem [

The first two thermal loads are simple to control. Because of the amount of well-established research on temperature difference due to sunlight, this paper will not go into detail on the subject. For box-girder bridges, a sudden change in temperature produces a complicated distributed load. It is instantaneous and uneven and has a major effect on local thermal stress. This is one of the main reasons that cause the box-girder cracking.

Sunlight causes sudden temperature change and annual temperature change. These changes will affect the different characteristics of the thermal load, as listed in Table

Contrast of different thermal loads.

Type | Influencing factors | Temporality | Scope | Distribution characteristics | Effect |
---|---|---|---|---|---|

Sunlight temperature changes | Solar radiation | Short-term rapid change | Partial | Uneven | High local stress |

Sudden drop in temperature changes | Severe cold air | Short-term changes | Total | Uniform | High stress |

Annual temperature change | Slow temperature changes | Long-term and slow | Total | More uniform | Large overall displacement |

In concrete structures, the thermal state of each point that is internal or on the surface of the structure at a certain moment is called thermal distribution. Due to the low coefficient of thermal conductivity of concrete, the obvious hysteresis occurs in the internal temperature changes in case of abrupt changes in surface temperature. As a result, there is a large difference in the formation of each layer of structure components or heat diffusion nonlinear temperature state.

Thermal load considered in this paper is mainly caused by a drastic temperature drop. When weather changes dramatically, ambient temperature changes can reach 10°C within 24 hours. At that moment, the external temperature variation of a box-girder bridge is relatively uniform, but the temperature changes through the thickness direction very different. Commonly, steel bar has a small effect on thermal distribution, and its influence can be ignored.

Thermal load acting on an engineering structure is generated by weather conditions. The thermal load of an engineering structure is a function that changes over time. Together with the thermal distribution, which is multidimensional in geometry, analyzing the load is complicated and demanding a rigorous analytical solution is impossible. The so-called “thermal load analysis of an engineering structure” is loosely defined as the use of different calculation methods to determine the distribution of a specific temperature in an engineering structure. For a certain internal or surface point of an engineering structure, the temperature _{i} at a certain moment can be expressed as

In equation (

The measured data shows that the heat conduction state of a concrete structure can be approximated by a one-dimensional heat conduction state. From a practical point of view, the approximation is allowed so that the complexity of the problem may be greatly simplified. Since the measured temperature distribution along the longitudinal direction of the bridge is always relatively even, the temperature difference can then be neglected through the longitudinal direction of the bridge. On a bridge deck, there is always a main heat conduction direction. For example, the heat conduction along the vertical direction is much greater than it is along the horizontal direction when influenced by solar radiation. Therefore, the heat conduction through the horizontal direction, which is quite small, can be omitted.

In the initial transient heat conduction, the known function of the temperature field coordinates is _{0} = constant.

The actual value of the concrete surface temperature may be measured by the sensors, so the first boundary condition is selected. That is,

Since the temperature difference can be neglected along the longitudinal direction of the bridge, the heat conduction equation can be written as

Referred by Stephenson, Priestlay, and Liu, the following semitheoretical and semiempirical formula can be used for the one-dimensional temperature field:

This test case is a prestressed concrete continuous box-girder bridge with uniform cross section in central China. It is an east-west bidirectional four-lane bridge, 116 m in length and 10 m in width. The span combination is 23 + 2 × 35 + 23 m in four spans. The design load conforms to Chinese highway level one load. That is, for lane load, the uniform distributed load is 10.5 kN/m. The concentrated load is selected in accordance with the following provisions: when bridge calculated span is less than or equal to 5 m, _{K} = 180 kN; when the calculated span greater than or equal to 50 m, _{K} = 360 kN; if bridge span is between the two, _{K} is obtained by interpolating. The main beam material is C50 concrete. In order to study the impact of a sudden change in the temperature of a box girder, a long-term continuous observation was carried out in the autumn and the winter of 2011 in every half-hour interval. The test was to primarily measure the environment temperature and the temperature of the box-girder surface. Figure

Measuring point layout.

Measuring point layout on section.

According to the meteorological data, the temperature records of drastic temperature changes for analysis were figured out. Figure

External temperature test curve of the box girders.

Figure

The box girders internal temperature test curve.

With the comparison of the temperature curve between the inside and the outside, both can be seen to follow roughly the same trend. But due to low concrete thermal conductivity, the internal temperature change of box girders is more gradual than the outside. Figure

Inside and outside temperature contrast.

Changing curve of temperature difference.

According to the measured temperature data, the maximum box-girder temperature difference between the inside and the outside was −12.8°C. At that time, the outside temperature of the box girder was −10.5°C, and the inside was 2.3°C. The bottom plate thickness was 0.25 m. Following the semitheoretical semiempirical formula shown in equation (

In the stress calculation caused by thermal load, the temperature distribution along the girder longitudinal direction is assumed to be fairly uniform, and the small differences in the distribution due to small change of the cross section are ignored. Concrete is considered a homogeneous and isotropic material, and it is in line with the law of elastic deformation before cracking. The planar cross-section assumption is tenable. Thermal stress is firstly calculated under individual load of temperature difference and then superimposed.

A box girder was modeled with a bridge-dedicated analysis software. A typical single-box single-cell girder cross section is selected for this bridge. An eight-node solid element was used to simulate and analyze with measured parameters. There were 50,715 nodes and 41,560 elements for the RC model and 50,747 nodes and 41,576 elements for the PC model. The cross section of the box girder is shown in Figure

Box-girder cross section.

FEM model.

Materials of the model are shown as follows:

Concrete: C50; modulus of elasticity: 34500 MPa; Poisson’s ratio: 0.2; single shaft ultimate tensile strength: 2.6 MPa; single shaft ultimate compressive strength: 32.4 MPa; bulk density: 2460 kg/m^{3}.

Prestressed reinforcing steel: Rj = 1860 MPa; diameter: 15.24 mm.

Four working conditions are set:

Condition 1: dead load + effect of temperature difference between the inside and the outside of the box.

Condition 2: dead load + effect of temperature difference between the inside and the outside of the box + live load.

Condition 3: dead load + effect of temperature difference between the inside and the outside of the box + prestress.

Condition 4: dead load + effect of temperature difference between the inside and the outside of the box + prestress + live load.

Temperature distribution is considered as

Temperature distribution along the beam thickness direction.

Results of working Conditions 1 and 2 are shown in Figures

Condition 1: dead load + effect of temperature difference.

Condition 2: dead load + effect of temperature difference + live load.

For the reinforced concrete bridge, the results of the calculation by Condition 1 show that, with only the temperature effect, the maximum stress of the lower edge of the base plate has reached 5.9 MPa, while the C50 concrete tensile strength is only 2.6 MPa. Therefore, only under the influence of the dead load and the temperature difference between the inside and outside of the box girder, the edge of the box girder will crack. When the vehicle load (Condition 2) is added, the tensile stress of lower edge increases further. Therefore, in the actual operational process, if the cold wave occurs near the bridge site region, the bottom of the box girder would form a large crack under the combined action of dead load, vehicle load, and the temperature difference between the inside and the outside of the box.

Results of working Conditions 3 and 4 are shown in Figures

Condition 3: dead load + effect of temperature + prestressed.

Condition 4: dead load + effect of temperature + prestressed + vehicle load.

For a prestressed concrete bridge, the results of the calculation by Condition 3 show that the stress of the bottom slab is between 1.9 and 2.3 MPa when affected by dead load, temperature difference, and prestressed force. Compared with the tensile strength of the concrete, 2.6 MPa, the difference between them is small. Due to the quality of on-site pouring, concrete strength is discrete. Hence, there would be some parts with insufficient strength. This may also cause cracking.

The results of Condition 4 show that, under the effect of dead weight, temperature, and vehicle load, the stress of the bottom slab is still up to 3.4 MPa, even for a prestressed concrete bridge. Average stress also reaches 2.7 MPa. A prestressed concrete box girder in the actual process operation will still crack, especially within an area with extreme weather.

In summary, compared with the reinforced concrete structure, despite the fact that prestressed concrete structures’ force has greatly improved, the tensile stress on the bottom of the box girder generated by temperature difference and vehicle load is generally higher than the tensile strength of the concrete. Thus, it is likely to crack in practice. The thermoelectric effect along the bridge longitudinal direction is not in effect. As a result, if there is cracking, it would cover the whole bottom slab, which corresponds to the actual observations (as illustrated in Figures

We have studied in this paper the influence of the temperature on the cause of cracking in concrete box-girder bridges, based on our inspections of highway bridges of this type in the China Central Plains region. The cause of cracking was first investigated, followed by the case study on the field measurement. To analysis the cracking issue, we have built finite element models for four different working conditions such as dead load and the effect of temperature difference between the inside and the outside of the box. Our results reveal that, due to the temperature difference between the inside and the outside of the box, the thermal self-restraint stress comes into place. Affected by temperature difference, the tensile stress of the bottom slab exceeds the tensile strength of the concrete. Moreover, building more ventilation holes to enhance the box-girder internal and external heat exchange is more effective to make inside and outside temperatures closer and to help reduce the probability of cracking caused by temperature differences. However, since this study focuses mainly on the thermal differential effect in the central plains of China. Due to differences in geographical environments, the environmental conditions of bridges in nearby locations are not all the same. Therefore, future reference values of thermal differential effects in different regions need to be collected in the future to extend the study.

The data used to support the findings of this study are available from the corresponding author upon request.

The authors declare that they have no conflicts of interest.