By new advancements in vehicle manufacturing, evaluation of vehicle quality assurance has got a more critical issue. Today noise and vibration generated inside and outside the vehicles are more important factors for customers than before. So far several researchers have focused on interior noise transfer path analysis and the results have been published in related papers but each method has its own limitations. In present work, the vibration transfer path analysis and vibration path ranking of a car interior have been performed. As interior vibration is a source of structural borne noise problem, thus, the results of this research can be used to present the structural borne noise state in a vehicle. The proposed method in this paper does not need to disassemble the powertrain from the chassis. The procedure shows a good ability of vibration path ranking in a vehicle and is an effective tool to diagnose the vibration problem inside the vehicle. The simulated vibration spectrums in different speeds of the engine have a good compliance with the tested results; however, some incompatibilities exist and have been discussed in detail. The simulated results show the strength of the method in engine mount optimization.
Noise and vibration which are perceived by passengers in a vehicle are important in the pleasantness of customers. Transfer path analysis of noise in a vehicle is a subject that many researchers from the 90s up to now have worked on it to find the root cause of a noise problem in a vehicle. By taking help of these methods, the paths of noise, which usually starts from engine, mounts through body, and ends to passenger compartment, are investigated. Transfer path analysis can find the weak points of every path of the vehicle; then, the paths of high noise are identified and ranked. An NVH engineer then is able to find the problem and find a design solution for making the transmission of noise better.
The earliest work in this subject refers to Bendat and Piersol [
Because of complexity in measuring the excitation forces on interfaces, the indirect procedures were developed. In these methods there is no need for direct measurement of interfacing forces. Instead, FRFs between all points of source and the FRFs between source and receiver (targets) are measured. Then, by inversing the FRF matrices and multiplying it with the operational accelerations at the input side, the shares of each path from overall noise are calculated [
Multilevel TPA has the strength of indirect measurement but can be done in a shorter time relative to indirect method. It was first introduced in 2002 by Eisele et al. [
Although almost all publications in interior noise transfer path analysis have focused on interior noise simulation, there is no work on the interior vibration simulation. In this paper, an interior vibration simulation of the vehicle for the first time was done. The method was based on multilevel TPA and the results show that this method has the ability of TPA analysis effectively. It is a fast method which rarely has the problem of measurement noise interfering. The results show that vehicle interior vibration simulation has good potential of engine mount optimization behaviour. By this method, also vibration fault diagnosis is more effective than conventional noise path ranking methods.
Vibrations in a vehicle mostly transfer from engine mount locations through vibration transfer paths into the body of the car and finally receives to the target locations in passenger compartment. Elements in vibration generation and transfer into the vehicle are divided into two major parts: active and passive elements. IC engine is an active vibration source, and the engine mounts and body transfer functions from mount locations to target points in the vehicle compartment are passive elements.
In passive part of vibration transfer, each engine mount in each vehicle principal coordinate comprises one path. Thus, for a vehicle with 3 engine mounts, there are 9 transfer paths. These engine mount paths beside relative body and chassis transfer functions send vibration energy to the passenger compartment.
Basic equation in transfer path analysis assumes that the total noise and vibration felt at passenger position are superposing the contribution of each path. Equation (
The system approach to the transfer path analysis explains that the partial contribution
By combining (
As it is clear from (
Multilevel TPA is classified in fast TPA groups of methods in which the contribution to a target response is a chain of linked subsystems. In this method, few FRF measurements are being performed and then by multiplying the input signal to this chain, the output will be the vibration share of each path at target location (
By noting (
According to (
For evaluation of interior vibration in a sedan car compartment, a procedure of interior vibration simulation was applied based on multilevel TPA. The vehicle was equipped with a four-cylinder engine of 1.7 L. The engine and gearbox were installed on the chassis with three mounts, two rubber mounts and one hydraulic mount. The mounts are named RH mount, LH mount, and Rear mount. The RH mount was a hydraulic mount and LH and Rear mounts were rubber mounts. Figure
Transverse engine mounting system [
According to (
All of the measurements were performed with a B&K 3570 data acquisition with 25 Khz range FFT analyzer. There are two 4524 B&K triaxial accelerometers and a piezoelectric impact hammer of maximum 5 KN force range. The signals were recorded with a 7 Hz high pass filter to prevent double hit error of impact hammer.
First, the body transfer function (
P1: hammer excitation, P2: triaxial accelerometer for body transfer function, and P3: triaxial accelerometer for chassis apparent mass [
Figure
Body transfer function of RH mount at different directions.
Apparent mass also was measured at engine mount locations. A triaxial accelerometer was installed on body near the engine mount location of the vehicle and the impact hammer applied the force beside the accelerometer position (Figure
Apparent mass of RH mount region.
Mount transmissibility is the ratio of acceleration on both sides of the mount on engine and body sides. The mount transmissibility was calculated by installing one accelerometer on engine side of each mount and another accelerometer on chassis side of mounts. Input and output acceleration on each engine mount were measured during a run-up of engine speed on the chassis dynamometer. The 3rd gear was engaged during the test and engine was under full load condition (fully open throttle). Figure
Test setup—(a) accelerometer installation on both sides of engine mount, (b) vehicle on chassis dyno.
The coherency spectrum of the mount transmissibility signal showed that only the main orders of the engine were coherent. Then only the transmissibility of these main orders was taken into account.
With a Matlab code the transmissibility of each mount at each direction was calculated at different engine speeds.
By multiplying the derived transfer functions with the input acceleration on engine side and summing the vibrations from different paths, the interior acceleration at passenger foot bottom could be simulated.
For comparison between simulated and real vibration at target point, a triaxial accelerometer also mounted at the target point (Figure
Calculation of mount dynamic stiffness in real conditions of mounts preload, temperature, and under engine operation is one valuable benefit of multilevel TPA, while dynamic mount stiffness measurement in test lab by a power shaker usually has large error.
Mount dynamic stiffness will be in hand by multiplying the mount transmissibility and apparent mass at different frequencies (see (
Figure
Dynamic mount stiffness derived by simulation.
Figure
Dynamic mount stiffness derived by simulation.
The differences between measured and simulated vibration signal in the vehicle come from the damping of the materials which covered the chassis of the vehicle on the foot bottom region. It was an asphalt layer. The property of damping of asphalt in this region is nonlinear which depends on temperature. As described earlier, the linear transfer function of body was taken into account in the analysis; then, the damping nonlinear behaviour of this layer cannot be considered in the analysis.
The effect of damping also grows with the velocity of excitation. Therefore, at higher speeds the measured vibration curve in Figure
These evidences show that the damping of body transfer paths has nonlinear frequency dependent behaviour and this property should be studied with more care.
Figure
Dynamic mount stiffness obtained by simulation.
This shows that LH mount needs to be modified. Then softening of the LH mount can be a solution to this problem. Of course the side effect of mount softening on rigid body displacements of engine should be studied.
Although there were many advancements in the transfer path analysis of noise in the vehicle, rare publications exist on vibration simulation of vehicle interior. Interior vibration of a vehicle can be taken as a representative of structural borne noise. Also vibration simulation of a vehicle interior is a powerful tool for engine mounts optimization. As it was proved, one can give applicable modifications on engine mount system to make the vibration behaviour better. Vibration TPA can realize the dynamic weak points of body chassis.
The results of vehicle interior vibration simulation and real measurements of this quantity showed a good compliance. The existing differences come from the nonlinear damping effect. Because of the linear assumption of body transfer functions in this method, these differences are inevitable.
A complete study on damping ratio effect on the simulated signal and also detailed mount optimization by this method will be performed in the next work. Also, further investigations are needed to be made on the effect of different gears on the amount of vibration at target point.
The authors declare that there is no conflict of interests regarding the publication of this paper.
The authors are grateful to the IPCO (Iran Khodro Powertrain Company) for supporting this research.