The Scientific World Journal

Volume 2013 (2013), Article ID 726963, 9 pages

http://dx.doi.org/10.1155/2013/726963

Research Article

Tensor Product Model Transformation Based Adaptive Integral-Sliding Mode Controller: Equivalent Control Method

Guoliang Zhao,1,2 Kaibiao Sun,¹ and Hongxing Li¹

¹Faculty of Electronic Information and Electronic Engineering, Dalian University of Technology, Dalian 116024, China

²Modern Manufacture Engineering Center, Heilongjiang University of Science and Technology, Harbin 150022, China

Received 21 August 2013; Accepted 21 September 2013

Academic Editors: C. Bao, S. Kou, A. Szekrenyes, and M. Yao

Copyright © 2013 Guoliang Zhao et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

This paper proposes new methodologies for the design of adaptive integral-sliding mode control. A tensor product model transformation based adaptive integral-sliding mode control law with respect to uncertainties and perturbations is studied, while upper bounds on the perturbations and uncertainties are assumed to be unknown. The advantage of proposed controllers consists in having a dynamical adaptive control gain to establish a sliding mode right at the beginning of the process. Gain dynamics ensure a reasonable adaptive gain with respect to the uncertainties. Finally, efficacy of the proposed controller is verified by simulations on an uncertain nonlinear system model.

1. Introduction

Sliding mode control (SMC) has advantages like ease of implementation and reduction in the order of the state equation. It also has the ability to withstand external disturbances and model uncertainties satisfying the matching condition, that is, the perturbations that enter the state equation at the same point as the control input. SMC design comprises two steps: a sliding surface is first constructed such that the system trajectories along the sliding surface meet the specified performance and then a discontinuous or continuous control law drives the states towards the sliding surface, and keeps them on the surface thereafter, regardless of disturbances or parasitic uncertainties. The resulting controller, although robust against matched perturbations, still suffers from reaching phase problem, that is, an initial period of time in which the system has not yet reached the sliding surface and it is sensitive to perturbations satisfying the matching condition.

In order to solve the reaching phase problem, an integral-sliding surface was proposed [1, 2]. Successively, many application examples of integral-sliding mode control have been developed in the literature and different systems are studied, such as multi-input multi-output (MIMO) linear system [3], uncertain nonlinear system [4, 5], uncertain stochastic system [6], and uncertain fractional order nonlinear system [7]. Some practical applications are also investigated [8–10]. The basic idea of integral-sliding surface control design is to define the nominal control law, which is responsible for the performance of the nominal system, that is, without perturbations, and a discontinuous or continuous control law, which is responsible for suppression of the parasitic uncertainties and external disturbances or perturbations. In integral-sliding surface control, an integral term is included in the sliding surface, and it allows to define the sliding surface in such a way that the system trajectories start in the sliding motion right at the beginning of the process. Moreover, it is well known that terminal sliding mode control (TSMC) guarantees a finite convergence time, by combining derivative and integral terminal sliding modes in a recursive structure; derivative-integral terminal sliding mode control (DI-TMSC) methods are proposed to achieve exact or approximate finite-time convergence for the output tracking of higher order nonlinear systems [11]. More recently, several works on the TP model transformation based sliding mode control appeared in the literature [12–16].

TP model transformation was first introduced by Baranyi et al. [17, 18]. It allows transforming dynamic system models defined over bounded domains into convex parameter-varying weighted combination of linear time invariant (LTI) systems. This transformation can transform a function into TP function form if it is feasible. If an exact transformation is impossible to achieve, then the method will determine a TP function which can be taken as an approximation. This feature offers the TP model transformation the ability to provide a tradeoff between approximation accuracy and complexity of the resulting TP model. linear parameter varying (LPV) based control has developed based on TP model transformation and linear matrix inequality (LMI) [17–22]. TP model transformation has found many applications in new direction in control theory [16, 23–25]. For further information., please refer to recently published monograph for qLPV control theories [26] and papers [19, 27].

Inspired by the adaptive sliding mode controller [28], the TP model transformation based parallel distributed compensation (TPDC) technique is applied, and a TP model transformation based adaptive integral-sliding mode controller (TPAISMC) is proposed in this paper. By combining with -adaptation strategy [29], a real sliding surface is realized; due to uncertainties and external disturbances, the phenomenon that adaptive gain is increasing all the time when ideal sliding mode does not occur is avoided. Chattering caused by perturbations and uncertainties [30] is suppressed by TPAISMC with -adaptation. Furthermore, the design process can be numerically realized without analytical derivation due to the characteristics of the TP model transformation based parallel distributed compensation. Thus, this control scheme has potential applications in many practical environments.

The rest of the paper is organized as follows. In Section 2, the concept of TP model transformation is introduced, and the control problem is formulated. In Section 3, TP model transformation based adaptive integral-sliding model control is presented, and TP model transformation based adaptive integral-sliding model control with -adaptation method is proposed. In Section 4, the simulations on TP model transformation based adaptive integral-sliding model controllers with different adaptive gain dynamics are carried out, and the control performance is tested. Finally in Section 5 the conclusions are given.

2. Preliminaries

2.1. Tensor Product Model Transformation

It is known that a given bounded continuous function () can be approximated by tensor product over a compact domain . First, divide the compact domain into -dimensional hyper rectangular grid based on a given grid size; on each dimension, the locations are defined by the vector

where and the -dimensional hyper rectangular grid belongs to a bounded region . Then function can be sampled over the grid points as

where (for all : ). Sampled matrices are stored into a tensor where superscript “” means “sampled.” Then higher order singular value decomposition (HOSVD) is used to root out the redundant content of the sampled set. It follows that

where tensor and is the vector space of real-valued tensors; is the number of univariate basis functions used in the th dimension of the parameter vector and is the entry of . Tensor satisfies the following properties.

(i)All-orthogonality: for all possible values of , , and ().(ii)Ordering: for all possible values of , where is the Frobenius norm. Row vector contains basis functions, and is normalized to one, where (; ). For the LPV state space model, TP model representation can be obtained as

where are the convex hull of the LTI vertex systems and is the linear index equivalent of -dimensional array’s index . Note that if all the discarded singular values are zero, this is the exact form of the original tensor and the approximation error is zero. If nonzero singular values are discarded, TP approximation error results in the following representation:

where is used to symbolize the approximation error; it is a function of discarded singular values and is the coefficient function.

2.2. Problem Statement

Consider a class of th-order uncertain nonlinear systems. The control system is represented in a state-space form as

where is the state vector, is the control input, and are the smooth vector fields, and is the external disturbance or parasitic uncertainties. Note that (6) is in a controllable form. The system and input matrices and are not exactly known but assumed to be in the form and , where and are the nominal parts of and , respectively. Assume that the nominal part of (6) can be transformed into TP models; that is,

Let be the lumped uncertainty and denoted as

Then the uncertain nonlinear system (6) can be represented as

Assume that the following hypothesis holds for the uncertain nonlinear system (6).

Assumption 1. The nominal parts and of uncertain nonlinear system (6) can be transformed into TP model.

Assumption 2. The matrix product is invertible.

Assumption 3. The actual values of , , and are unknown, but their bound should exist for all and .

Assumption 4. The known nominal nonlinear plant of (6), , is globally asymptotically stabilizable via a nominal control ; that is, there is a nonempty set of Lyapunov function such that for any choice of function satisfies

where are class functions and is a class function, where is the set of all continuous functions that are zero at zero, strictly increasing, and continuous and is the subset of consisting of those functions that are unbounded.

The following nonlinear integral-type sliding surface [31, 32] is used in the adaptive sliding mode control design:

Remark 1. The reaching phase is eliminated for nonlinear integral-type sliding surface defined by (11). It is obvious that the sliding mode exists from the very beginning. The additional integral provides another degree of freedom than the linear sliding surface, and this term can be thought of as a trajectory of the nominal system, that is, the system in the absence of perturbations and in the presence of the nominal control . In this work, equivalent control is given by TP model transformation based parallel distributed compensation (PDC) technique [17]. Moreover, is assumed to be in the linear form; that is, in [31, 32] is removed. The requirement of is just to satisfy Assumption 1 in this paper. Thus, our method can be applied to a variety of nonlinear systems in which TP model transformation can be applied, for example, inverted pendulum system, underactuated robot manipulators [33], translational oscillator with a rotational actuator (TORA) [34], vertical takeoff and landing (VTOL) aircraft [35], and quadrotor helicopter [36].

3. TP Model Transformation Based Adaptive Integral-Sliding Mode Control Design

The adaptive sliding mode control law using the integral-sliding surface (11) can be designed as

where the gain is the adaptive value preserving the sliding mode and is the signum function. Updating law is designed as

where and . For the nominal feedback, TP model transformation based parallel distributed compensation (TPDC) is used; gains are computed by the following LMI-based stability.

Theorem 2 (see [21]). The polytopic model (4) with the equivalent control (12) is asymptotically stable if there exist and that satisfy

for , and

for , except the pairs such that , for all , and the feedback gains are determined by the solutions and as

Theorem 3 (see [21]). Assume that , where is unknown, but the upper bound is known. The constraint is enforced at all times if the following LMIs hold:

The aforementioned control algorithm can be summarized as follows.

Theorem 4. Consider the uncertain nonlinear system (6). Given the integral-type sliding surface (11) and the adaptive control law (12), the sliding mode is guaranteed to be reached in finite time.

Proof. Assume that there exists a final gain such that is the optimal solution for , and . It is always true since adaptive gain is increasing. Differentiating the sliding surface (11) with respect to time, it yields

A Lyapunov function is chosen as , where . Differentiating with respect to time using (12) and (18), it yields

By applying , (19) becomes

It can be inferred that and reach zero in finite time; that is, and . The convergence of and is proven by Lyapunov stability criterion. In practice, the discontinuous switching function in (12) may cause chattering in the sliding mode. In order to alleviate the input chattering, switching function is replaced with the saturation function , where is the boundary layer width which should be carefully chosen according to each particular control system. This completes the proof.

Remark 5. Briefly, the proposed TPAISMC scheme provides the following three main advantages. First, the knowledge of the upper bound of the system uncertainties is not required. Second, TP model transformation has the ability to provide a tradeoff between approximation accuracy and complexity of the resulting TP function. If an exact transformation is impossible, approximation error is bounded by discarded singular values, then this error can be incorporated into lumped uncertainty . Third, the tracking performance of the control system is guaranteed.

The above adaptive method does not require knowledge of uncertainties or perturbations bound. Adaptive gain may increase all the time when . However, this happens all the time in real applications due to sampled computation, noisy measurements, or other nonidealities, sliding surface can hardly achieve zero exactly. The method referred to as “-adaptation” proposed in [29] is adopted to counteract the uncertainties and perturbations effects; based on integral-sliding surface and TP model transformation, the adaptive sliding mode controller with -adaptation is given as follows:

where the gain is defined as

where is a prescribed positive parameter. By Lemma 2 [29], there exists a positive constant such that for all and . Furthermore, (18) can be simplified as

by uncertain nonlinear system (6) and is given by (21). Choose Lyapunov function as . Differentiating with respect to time, using (21) and (23), it yields

when . Suppose that , we have

Suppose that , could be sign indefinite, can increase over , then adaptive gain will increase to guarantee the sliding motion, and then the control strategy ensures that again. When , differentiating with respect to time, using (22), it yields

In the adaptive sliding mode controller design, -adaptation is used to regulate the adaptive gain, combining with TPPDC, the following theorem holds.

Theorem 6. Consider the uncertain nonlinear system (6). Given the integral-type sliding surface (11) and the control law (21), the sliding mode is guaranteed to be reached in finite time.

4. Simulations

Consider the following nonlinear system:

The nominal parts of system are and . TP model transformation is used to decompose , and the LTI systems are given by

Since the equivalent control method used in ASMC [28] is replaced with TPDC, the newly proposed method is referred to as TP based adaptive sliding mode control (TPASMC). States responses with TPASMC are shown in Figure 1(a), the sliding surface function is shown in Figure 1(b), and control input and adaptive gain parameter are given in Figures 2(a) and 2(b), respectively. We can conclude that the equivalent control based on TPDC used in TPASMC has the same performance as ASMC which is proposed by Huang et al. [28]. However, since the TPDC is a numerical method, we can design the adaptive sliding mode controller without knowing the analytical system model. There is no modeling error for the nominal system when all the nonzero singular values are used in TP model transformation. The boundary layer technique is applied to avoid high-frequency control activity; the signum function in is replaced with , and we have

where is the boundary layer width. In the simulation, , , , , the initial state vector for all the simulations is , and is the decay rate for TPDC. The desired trajectory is supposed to be . The disturbance is supposed to be a random noise possessing a mean value of 0.5 and .

(a)

(b)

Figure 1: (a) States responses with TPASMC. (b) Sliding surface function with TPASMC.

(a)

(b)

Figure 2: (a) Control input with TPASMC. (b) Adaptive gain parameter.

Figure 3(a) shows the states responses of TPASMC with integral-sliding surface (TPAISMC), sliding surface function is shown in Figure 3(b), and Figures 4(a) and 4(b) show the control input and adaptive gain parameter, respectively. To implement TPAISMC, the following parameters are used:

For integral-type sliding surface, reaching phase is eliminated; this can be verified by Figure 3(b). However, in real application, the ideal sliding surface does not exist, then the adaptive gain may increase forever (as shown in Figure 4(b)) when the sliding surface reaches nonzero; the adaptive strategy (13) may cause chattering when the adaptive gain grows large.

(a)

(b)

Figure 3: (a) States responses with TPAISMC. (b) Sliding surface function with TPAISMC.

(a)

(b)

Figure 4: (a) Control input with TPASMC. (b) Adaptive gain parameter.

To avoid large adaptive gain and chattering, we apply the adaptation law (22) to reduce the chattering. For TPAISMC with adaptation, the following parameters are used:

Figure 5(a) shows the states responses with TPAISMC when -adaptation is used. Sliding surface function is shown in Figure 5(b) and control input and adaptive gain parameter are shown in Figures 6(a) and 6(b), respectively. Here it is clearly seen from Figure 5(b) that TPAISMC with -adaptation is effective in chattering suppression. Adaptive gain , defining the chattering amplitude in the sliding mode, increases to a reasonable level to guarantee a real sliding mode.

(a)

(b)

Figure 5: (a) States responses with TPAISMC (-adaptation). (b) Control input with TPAISMC (-adaptation).

(a)

(b)

Figure 6: (a) Sliding surface function with TPAISMC (-adaptation). (b) Adaptive gain parameter (-adaptation).

5. Conclusion

In this work, an adaptive siding mode controller scheme for a class of uncertain nonlinear system is studied, and an integral-sliding surface was adopted in the designing of TPAISMC. Instead of using the traditional feedback control, TP model transformation based parallel distributed compensation controller was applied to stabilize the states. It is noted that the modeling error caused by TP model transformation can be zero if nonzero singular value is discarded. Nonzero modeling error can be modeled as lumped uncertainties, combining modeling error with perturbations and external disturbances, and can be suppressed effectively by adaptive gain controller with -adaptation strategy.

Acknowledgments

This work was supported by the National Natural Science Foundation of China (no. 11101066; no. 61074044; no. 61374118; no. 61104038; no. 60834004) and the Fundamental Research Funds for the Central Universities (no. DUT13LK32), and partially supported by the Chinese National Basic Research 973 Program (2009CB320602).

References

G. P. Matthews and R. A. DeCarlo, “Decentralized tracking for a class of interconnected nonlinear systems using variable structure control,” Automatica, vol. 24, no. 2, pp. 187–193, 1988.

V. Utkin and J. Shi, “Integral sliding mode in systems operating under uncertainty conditions,” in Proceedings of the 35th IEEE Conference on Decision and Control. Part 4 (of 4), pp. 4591–4596, December 1996.

T.-Z. Wu, J.-D. Wang, and Y.-T. Juang, “Decoupled integral variable structure control for MIMO systems,” Journal of the Franklin Institute, vol. 344, no. 7, pp. 1006–1020, 2007.

H. Huerta, A. G. Loukianov, and J. M. Cañedo, “Multimachine power-system control: integral-SM approach,” IEEE Transactions on Industrial Electronics, vol. 56, no. 6, pp. 2229–2236, 2009.

S. Laghrouche, F. Plestan, and A. Glumineau, “Higher order sliding mode control based on integral sliding mode,” Automatica, vol. 43, no. 3, pp. 531–537, 2007.

Y. Niu, D. W. C. Ho, and J. Lam, “Robust integral sliding mode control for uncertain stochastic systems with time-varying delay,” Automatica, vol. 41, no. 5, pp. 873–880, 2005.

S. Dadras and H. R. Momeni, “Passivity-based fractional-order integral sliding-mode control design for uncertain fractional-order nonlinear systems,” Mechatronics, vol. 23, no. 7, pp. 880–887, 2013.

J. Komsta, N. van Oijen, and P. Antoszkiewicz, “Integral sliding mode compensator for load pressure control of die-cushion cylinder drive,” Control Engineering Practice, vol. 21, no. 5, pp. 708–718, 2012.

S.-U. Lee and P. H. Chang, “Control of a heavy-duty robotic excavator using time delay control with integral sliding surface,” Control Engineering Practice, vol. 10, no. 7, pp. 697–711, 2002.

X.-H. Mo and Q.-X. Lan, “Finite-time integral sliding mode control for motion control of permanent-magnet linear motors,” Mathematical Problems in Engineering, vol. 2013, Article ID 567610, 7 pages, 2013.

C.-S. Chiu, “Derivative and integral terminal sliding mode control for a class of MIMO nonlinear systems,” Automatica, vol. 48, no. 2, pp. 316–326, 2012.

P. Korondi, “Tensor product model transformation based sliding surface design,” Acta Polytechnica Hungarica, vol. 3, no. 4, pp. 23–35, 2006.

P. Korondi, H. Hashimoto, and G. Sziebig, “Sliding sector design for nonlinear systems,” in Proceedings of the 17th World Congress: The International Federation of Automatic Control, Seoul, Korea, July 2013.

B. Takarics, P. Korondi, and P. Baranyi, “TP model transformation based sliding mode control design for nonlinear systems,” in Proceedings of the 14th International Power Electronics and Motion Control Conference (EPE-PEMC '10), pp. T1061–T1068, Ohrid, Macedonia, September 2010.

B. Takarics, TP model transformation based sliding mode control and friction compensation [Ph.D. dissertation], BME, Budapest, Hungary, 2011.

B. Takarics, “Parallel distributed compensation based sector sliding mode control of Takagi-Sugeno type polytopic models,” in Proceedings of the 10th International Symposium on Applied Machine Intelligence and Informatics (SAMI '12), Herl'any, Slovakia, January2012.

P. Baranyi, “TP model transformation as a way to LMI-based controller design,” IEEE Transactions on Industrial Electronics, vol. 51, no. 2, pp. 387–400, 2004.

P. Baranyi, D. Tikk, Y. Yam, and R. J. Patton, “From differential equations to PDC controller design via numerical transformation,” Computers in Industry, vol. 51, no. 3, pp. 281–297, 2003.

P. Baranyi, P. Várlaki, and Y. Yam, “Tensor product model transformation in polytopic model-based control,” in Automation and Control Engineering, CRC Press, Taylor and Francis, 2013.

P. Baranyi, P. Korondi, and H. Hashimoto, “Global asymptotic stabilization of the prototypical aeroelastic wing section via TP model transformation,” Asian Journal of Control, vol. 7, no. 2, pp. 99–111, 2005.

Z. Petres, P. Baranyi, P. Korondi, and H. Hashimoto, “Trajectory tracking by TP model transformation: case study of a benchmark problem,” IEEE Transactions on Industrial Electronics, vol. 54, no. 3, pp. 1654–1663, 2007.

P. Baranyi and A. R. Várkonyi-Kóczy, “TP transformation based dynamic system modeling for nonlinear control,” IEEE Transactions on Instrumentation and Measurement, vol. 54, no. 6, pp. 2191–2203, 2005.

A. Rovid, L. Szeidl, and P. Várlaki, “On tensor-product model based representation of neural networks,” in Proceedings of the 15th IEEE International Conference on Intelligent Engineering Systems (INES '11), Poprad, Slovakia, June 2011.

C. Sun, Y. Huang, C. Qian, and L. Wang, “On modeling and control of a flexible air-breathing hypersonic vehicle based on LPV method,” Frontiers of Electrical and Electronic Engineering in China, vol. 7, no. 1, pp. 56–68, 2012.

P. Baranyi and Y. Yam, “Case study of the TP-model transformation in the control of a complex dynamic model with structural nonlinearity,” IEEE Transactions on Industrial Electronics, vol. 53, no. 3, pp. 895–904, 2006.

S. Nagy, Z. Petres, P. Baranyi, and H. Hashimoto, “Computational relaxed TP model transformation: restricting the computation to subspaces of the dynamic model,” Asian Journal of Control, vol. 11, no. 5, pp. 461–475, 2009.

R.-E. Precup, C.-A. Dragoş, S. Preitl, M.-B. Rǎdac, and E. M. Petriu, “Novel tensor product models for automatic transmission system control,” IEEE Systems Journal, vol. 6, no. 3, pp. 488–498, 2012.

Y.-J. Huang, T.-C. Kuo, and S.-H. Chang, “Adaptive sliding-mode control for nonlinear systems with uncertain parameters,” IEEE Transactions on Systems, Man, and Cybernetics, Part B, vol. 38, no. 2, pp. 534–539, 2008.

F. Plestan, Y. Shtessel, V. Bregeault, and A. Poznyak, “New methodologies for adaptive sliding mode control,” International Journal of Control, vol. 83, no. 9, pp. 1907–1919, 2010.

H. Lee and V. I. Utkin, “Chattering suppression methods in sliding mode control systems,” Annual Reviews in Control, vol. 31, no. 2, pp. 179–188, 2007.

F. Castaños and L. Fridman, “Analysis and design of integral sliding manifolds for systems with unmatched perturbations,” IEEE Transactions on Automatic Control, vol. 51, no. 5, pp. 853–858, 2006.

W.-J. Cao and J.-X. Xu, “Nonlinear integral-type sliding surface for both matched and unmatched uncertain systems,” IEEE Transactions on Automatic Control, vol. 49, no. 8, pp. 1355–1360, 2004.

G. Oriolo and Y. Nakamura, “Control of mechanical systems with second-order nonholonomic constraints: underactuated manipulators,” in Proceedings of the 30th IEEE Conference on Decision and Control, pp. 2398–2403, December 1991.

M. Jankovic, D. Fontaine, and P. V. Kokotović, “TORA example: cascade- and passivity-based control designs,” IEEE Transactions on Control Systems Technology, vol. 4, no. 3, pp. 292–297, 1996.

R. Olfati-Saber, “Normal forms for underactuated mechanical systems with symmetry,” IEEE Transactions on Automatic Control, vol. 47, no. 2, pp. 305–308, 2002.

E. Altuǧ, J. P. Ostrowski, and R. Mahony, “Control of a quadrotor helicopter using visual feedback,” in Proceedings of the IEEE International Conference on Robotics and Automation, pp. 72–77, Washington, DC, USA, May 2002.