The Scientific World Journal

Volume 2014 (2014), Article ID 818135, 9 pages

http://dx.doi.org/10.1155/2014/818135

Research Article

Fault Tolerant Coverage and Connectivity in Presence of Channel Randomness

Anil Kumar Sagar and D. K. Lobiyal

School of Computer and Systems Sciences, Jawaharlal Nehru University, New Delhi 110067, India

Received 31 August 2013; Accepted 24 October 2013; Published 21 January 2014

Academic Editors: A. Manikas and Y. Qi

Copyright © 2014 Anil Kumar Sagar and D. K. Lobiyal. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

Some applications of wireless sensor network require -coverage and -connectivity to ensure the system to be fault tolerance and to make it more reliable. Therefore, it makes coverage and connectivity an important issue in wireless sensor networks. In this paper, we proposed -coverage and -connectivity models for wireless sensor networks. In both models, nodes are distributed according to Poisson distribution in the sensor field. To make the proposed model more realistic we used log-normal shadowing path loss model to capture the radio irregularities and studied its impact on -coverage and -connectivity. The value of can be different for different types of applications. Further, we also analyzed the problem of node failure for -coverage model. In the simulation section, results clearly show that coverage and connectivity of wireless sensor network depend on the node density, shadowing parameters like the path loss exponent, and standard deviation.

1. Introduction

Wireless sensor network (WSN) consist of low-cost small sensor nodes equipped with small sensing, communication, and computation capabilities. These nodes are deployed either deterministically or stochastically and sense the events of interest and send this data to one or more sink. There are various applications of WSN which includes battlefield surveillance, environmental monitoring, health care, and vehicle traffic monitoring [1]. In hostile environments, where human intervention is difficult or impossible, sensors may be dropped randomly from an airplane. In this case, node density cannot be the same in the whole area. If less number of sensors are deployed, some area may be uncovered and some nodes may be isolated. To maintain quality of coverage and connectivity, large number of sensors are deployed. These redundant sensors improve coverage as well as connectivity but increase energy consumption and network cost which eventually reduces network lifetime. Quality of monitoring of a given area is a fundamental issue in many applications, which measures how well a sensor monitors the given target area. Therefore, coverage is one of the key factors to achieve quality of service in a wireless sensor network. Covering each point by only one sensor is desired in some applications, while in many applications, it is desired that more than one sensor can cover each point in the target area for better accuracy and fault tolerance. To deal with the problem of faulty sensors, some applications required -coverage; that is, every location in the field is covered by at least sensors. Connectivity is another factor that affects the quality of service. It enables the sensors to communicate with each other so that their sensed data can reach the sink. To ensure data delivery, multiple paths between a source and destination may be available. Therefore, if there are disjoint paths exist between two sensors, such a network is called -connected. In other words, a network is -connected, if any -1 nodes are randomly chosen and removed from the network, and it still remains fully connected. Therefore, in this paper, we are concerned with the -Coverage and -Connectivity problem which requires that every point in the bounded field is monitored by at least sensors at any point of time and there exists independent paths from a source to destination. In previous work, the sensing and transmission range of sensor nodes is assumed to be based on disk model; that is, it is assumed to be symmetric in all direction which is not correct in real environments. Generally, it is viewed that sensing and transmission range of the sensor nodes is affected by distance and obstacles present in the environments; this phenomenon is known as shadowing effect. This paper also investigates the impact of shadowing model on -Coverage and -Connectivity of wireless multihop networks where each point in the target region is covered by at least sensors and there are at least paths from source to destination. The rest of the paper is organized as follows. The earlier work related to coverage and connectivity done by various researchers is given in Section 2. The proposed system model, sensing model, and log-normal shadowing model are presented in Section 3. Further, in Section 4,  -coverage sensing affected by lognormal shadowing model is described. Section 5 explains -connectivity along with the effect of shadowing model. In Section 6, the effect of node failure on coverage is discussed. Simulation results and performance analysis of the model are presented in Section 7. The work in the paper is concluded in Section 8.

2. Related Work

Coverage and connectivity jointly had drawn the attention of researchers working in the design of multihop WSN. Several extensive studies related to coverage and connectivity in WSN have been proposed in the literature. However, most of the works have their basis on binary disk model of the channel propagation where the irregularity and randomness present in radio communications due to various environment effects are not considered.

Ammari and Das in [2] analyzed the problem of -coverage. In this paper, authors studied sensors duty cycling strategies so that in each scheduling round each and every location of the sensor field is monitored by at least active sensors and all these active sensors are also connected. Authors have also shown the relation between sensing and communication range for -coverage and connectivity among all active sensors. In [3], Cai et al. proposed a sleeping protocol named area-based collaborative sleeping (ACOS) which saves energy as well as maximizes the coverage. In ACOS, a sensor can be either in passive, active, preactive, or prepassive state and each sensor can calculate its surface area which is not covered by any other sensor. Esnaashari and Meybodi in [4] suggested automata-based deployment strategy, called extended cellular learning automata-based deployment strategy (CLA-EDS), for -coverage with mobile sensor nodes. This approach also calculates different degree of coverage in different region of the network. CLA-EDS deployment strategy does not use any information regarding the position of sensor nodes. In this approach, each node finds out its best position in cooperation with its neighboring nodes to attain high coverage. A partitioned synchronous network (p-sync) for coverage and connectivity together is studied by He et al. in [5]. To conserve energy, they used duty cycled approach in which sensor nodes are partitioned into number of disjoint subset. Authors also find out the optimal schedule for p-sync network and showed that connectivity is better in p-sync network rather than in synchronous network. Li et al. in [6] studied the problem of -connected target coverage which is fault tolerant, by using minimum number of active nodes. They have used two heuristics algorithms (TS) and (RA). TS algorithm covers all the targets using set cover algorithm and adds some new nodes to form -connected coverage. In RA algorithm, a sensor node goes in sleeping mode if there is no effect on coverage and any two neighbors of the node have node-disjoint paths. Bai et al. in [7] discussed the multiple coverage with optimal locations of sensor nodes. They also proved that the optimal congruent deployment density for 2-coverage is . Dhillon and Chakrabarty in [8] proposed an optimization problem on sensor placement. They proposed a greedy heuristic to provide sufficient coverage with minimum number of sensor nodes. They have also proposed polynomial-time algorithms for placement of minimum number of sensor nodes. In [9], authors studied the impact of under log-normal shadowing model on connectivity where sensor nodes are scattered according to homogeneous Poisson process over an infinite plane. The authors also provided tight lower bounds for minimum node density so that the network is surely connected. They further analyzed how fading affected the topology of multihop networks. Finally authors validated their analytical result with simulation. Hekmant and Van Mieghem [10] have analyzed the link probability in wireless ad hoc networks using geometric random graph model. To study the connectivity, authors used more realistic log-normal shadowing models.

3. System Model

In the system model, we have considered that sensors are deployed randomly and uniformly in the two-dimensional desired sensing area. These sensor nodes are static and homogeneous and deployed with high density according to a homogeneous Poisson distribution with density . Each sensor with radius can cover a circular area while ignoring the border effect. The area of interest is said to be covered by sensors if every point of interest lies within the sensing range of at least one sensor node. Each sensor node detects the event of interest and reports this to the sink. It is assumed that all nodes are equipped with transmitter and receiver having the same features; thus, we have a single value of sensing range for all nodes. However, the sensing range of each sensor nodes depends on fixed transmission power , and propagation loss due to distance and environment. All sensors are aware of their locations using some localization technique [11]. System parameters and their definitions are listed in Table 1.

Table 1: Parameters definitions.

Parameter
Definition

Number of sensor nodes

Node density

Transmission power of a sensor node

Path loss exponent

Close in reference distance

Standard deviation

Sensing sensitivity of sensor node

Threshold of received signal

Area of interest

Effective sensing range

Probability of node failure

Probability of detection of event

3.1. Sensing Model

Sensing coverage generally uses the binary disk model where each sensor’s coverage area is modeled by a disk. It is assumed that sensing area of a sensor is circle and sensor nodes sense in all direction uniformly; that is, it is omnidirectional. A sensor node detects an event of interest with probability one if it is in the sensing range of the sensor node and with probability zero otherwise. The target at point can be detected by the sensor if and only if . Depending on whether the event is located within the sensing range, the coverage function of the binary disk model is formulated as the sensing function given below

In the function, is the Euclidean distance between sensor node and a point ; and is sensing range of a sensor node. Figure 1(a) shows the transmission range of binary disk model which is assumed to be isotropic. Probabilistic sensing model is much more realistic than binary sensing model. The probability of event detection by a sensor node is dependent on the sensor-event distance. As the distance between sensor and event increases, the strength of sensing signal may drop along the path. In the probabilistic sensing model, the sensing function can be modeled as

where and are sensor-dependent parameters which represents the physical characteristic of the sensor, is the starting of uncertainty in sensor detection, and is the maximum practicable sensing range of sensor node. In real networks, radio fluctuations, obstacles, and noise cannot be ignored causing the random signal strength; this effect is called shadowing. Random attenuation due to shadowing is modeled as log-normal. Thus, log-normal shadowing is the most widely accepted model that considers shadowing effect. This model shows that average received signal strength decreases logarithmically with respect to distance between transmitter and receiver. Therefore, due to distance and shadowing effect, the sensing ability of sensors is not the same in all the directions (Figure 1(b)).

(a)

(b)

Figure 1: (a) Transmission range in ideal case. (b) Transmission range with impact of path loss and shadowing.

3.2. Log-Normal Shadowing Path Loss Model

This model represents radio propagation in real environment. Path loss is caused by dissipation of the power radiated by the transmitter as well as by the effects of fading and shadowing that is caused by impediments present between the transmitter and receiver. According to this model, both theoretical and measurement-based propagation models indicate that the average received signal power decreases logarithmically with the distance [12]. In this radio propagation path loss model, path loss corresponding to distance is described as

where is path loss corresponding to reference distance , is the path loss exponent that shows the rate of increasing path loss with distance, and expresses log-normal shadowing effect which is the Gaussian random variable with zero mean and standard deviation . The values of and are computed from measured data. This model assumes that path loss has same value when measured in different direction. However, Zhou et al. [13] showed experimentally that path losses should be nonisotropic due to many factors such as sending power, antenna gain, receiver sensitivity, signal-to-noise ratio, and obstacle present in the environment. Therefore, based on experiment of [13], path loss expressed in (3) will be

where

where

The DOI describe the maximum variance of path loss at every direction. Equation (4) requires angle information between communicating nodes to provide path loss in all directions and we have to generate 360 values for 360 different directions; therefore, its implementation is very complex. Hence, in [14], Xiao et al. proposed a simpler model which does not needed the information about angle between two sensor nodes; thus, DOI-adjusted path loss can be expressed as

The received signal strength at distance using DOI-adjusted path loss is

where the transmitted signal is power of the sender node and is the fading exponent. Therefore, from (8), the probability of received signal when its power level exceeds certain threshold is

where is the threshold of the received signal power. Using this probability described in (9), the sensor node calculates its communicating range, which is different for every node and depends upon shadowing effects.

4. -Sensing Coverage

Coverage means that every point in the target region is observed by at least one sensor. This is called 1-coverage. To improve accuracy and to cope up with sensor failure, some applications, such as forest fire detection, intruder detection, and military surveillance, require -coverage (), which means that every point in the region is monitored by at least distinct sensor nodes. For obstacle free environments, the sensing radius of a sensor node is assumed to be constant in all directions, but, in reality, the sensing radius of sensor node is not uniform in all directions due to reflection, refraction and scattering caused by obstacles present in the environment. If the received signal strength is greater than a specific threshold value, then only the sensor node detects the sensing signal this is known as sensing sensitivity. If the average sensing radius of a node is , the sensing sensitivity of a sensor node is expressed as [9]

where is sending power, is reference distance, and is path loss component.

4.1. -Sensing Coverage without Shadowing Impact

Let and be the effective sensing radius when of a sensor node and area of interest, respectively. Target in area will be detected by any randomly deployed sensor if it is within sensing radius () from the event. The probability that the target will be detected by an arbitrary sensor is

The probability of the target not being sensed by a randomly deployed sensor is

Let sensors be deployed randomly in the area of interest. The probability of the target not being sensed by any one of the sensor node is

The probability that the target will be detected by at least one of the nodes is

where is the effective sensing range of sensor node which can be calculated as [15]

With

4.2. -Sensing Coverage with Shadowing Impact

In a shadowing environment, sensing behavior of a sensor depends on the signal propagation and, therefore, sensing radius of a sensor node is not isotropic in all directions. Let us assume that a sensor node is deployed at a distance from the target location as shown in Figure 2; therefore, the received power (in decibel units) can be expressed as

Figure 2: Impact of shadowed environment on sensing.

A target is sensed by the sensor node when the received signal power is greater than some threshold value . The probability that the received power is greater than some threshold value can be expressed as

Here, function is used to calculate the probability that the received signal will exceed some threshold value. Where function is expressed as

As sensor nodes are randomly deployed at a distance over an area . The probability that, a sensor node is randomly deployed, at a location with distance to the event of interest, is , where is very small variation in distance. The probability that the event of interest is sensed by the sensor node is

Now, probability that a target is sensed by sensors out of sensors in sensing field of area is

Substituting the value of from (20),

Probability that at least sensors can cover the target location is given by

From (23), we can find the probability of -coverage; that is, each and every point in the field is detected by at least sensor nodes so that the network is made fault tolerable. It can also be easily seen from the equation that as the shadowing parameter increases, the probability of coverage decreases.

5. -Connectivity

In Wireless Sensor Networks, each sensor node sends its sensing data to the sink node by single or multi hop communication. So, one of the most significant property of WSN is the connectivity property that we will study in this subsection. The connectivity of a sensor network is affected by time, as time goes on, the energy of the sensor node depletes and sensor node fails and the network may be disconnected. -connectivity is an important QoS measure of network for fault tolerant system and thus enhances the communication reliability. -connectivity refers to the property of a randomly selected sensor node that has at least neighbors. That is, in connectivity, if () node fails, then connectivity still holds. Since wireless channel is affected from various environment impairments, therefore -connectivity performance is evaluated under log-normal shadowing model.

5.1. The Geometric Random Graph Model

A random graph is denoted by , where is the number of nodes and is the probability of having link between any two nodes. The degree of a node in a network is defined as the number of connections or links the node has to other nodes. In a random graph, each of nodes is connected with probability and not connected with probability that has binomial distribution degrees

For large value of and small value of , we can use the following approximations:

Therefore,

The Poisson approximation for large value of is given by

where is the mean node degree .

5.2. -Connectivity in Presence of Shadowing

Let us consider a wireless sensor network, where sensor nodes are randomly distributed in the area according to a homogeneous Poisson process with average intensity . The number of nodes per unit area is given by . The area of a sensor node with radius is . The probability that a randomly selected sensor node with area has neighbors is given by the following equation:

Now, the probability that a randomly selected sensor node has no neighbor, that is, the sensor node is isolated and the network is not connected

If a sensor node is isolated it cannot exchange information between other nodes and, thus, it is useless for the entire network. Penrose in [16] proved that there is a relationship between -connectivity and the minimum node degree; that is, . Therefore the expression for minimum node degree can be directly applied to -Connectivity. Due to shadowing effect, the range of the received signal is not symmetric in all directions. Receivers located at the same distance from the sender may have different values for received signal. The probability that each node with effective transmission range is -connected can be given by the following expression:

where is no. of nodes deployed, is node density, and is effective communication range.

6. Effect of Node failure on -Sensing Coverage

Sensor nodes were scattered in remote and hostile environment, where there is no human involvement to maintain sensor nodes. Some nodes may be failed due to noise, hardware malfunction, software problem, and battery energy depletion and these nodes cannot be repaired. Due to failure of nodes, coverage ratio may be decreased and network may be partitioned which results in network failure.

Let be the probability of node failure and let be the probability of detection of an event. The probability that there is no node failure is . Now, suppose that nodes are deployed to detect the target; the probability that out of nodes no node detects the event in presence of node failure is given by

The probability that out of nodes nodes detect the event in presence of node failure probability is given as follows:

Substituting the value of from (15),

From this equation, we can find out the probability of coverage in presence of node failure and shadowing.

7. Simulation Results and Performance Analysis

In this section, we present a performance analysis of network for -Coverage and -Connectivity. All nodes use the log-normal shadowing model for sensing and communication. Simulations are performed using MATLAB to investigate the -Coverage and -Connectivity results. Different values of simulation parameters used to conduct experiments are tabulated in Table 2. To show the effect of node density and shadowing parameters, we have conducted the following experiments:

(i)effect of node density and standard deviation on sensing coverage,(ii)effect of node failure on sensing coverage,(iii)effect of node density on connectivity,(iv)effect of shadowing parameter on connectivity,(v)effect of communication range on connectivity,(vi)effect of node distance on connectivity.

Table 2: Simulation parameter.

Parameter
Value

Number of sensor nodes ()
500

Area ()
10000 m²

Path loss exponent ()
3

Transmission power of a sensor node ()
20 W

Threshold of received signal ()
−58 dB

Effective sensing range ()
10 m

Below, we conducted all these experiments one by one.

(i) Effect of Node Density and Standard Deviation on Sensing Coverage. Figures 3 and 4 show the result of the probability of coverage versus the number of sensor nodes for different shadowing parameters (, 4). When the standard deviation of the shadowing environment is increased from 2 to 4, the average sensing radius of sensor node also decreases, and this requires more number of sensor nodes to achieve desired coverage. As shown in Figure 3, in order to provide 3-coverage with probability >90% and shadowing parameter , approximately 225 sensor nodes are required in the area of 100 × 100. When the shadowing parameter increases from 2 to 4, approximately 450 nodes are required to achieve 3-Coverage with the same probability. Slope of the curve in Figure 3 is bigger as compared to Figure 4. This concludes that when the standard deviation increases, probability of coverage is not increased in the ratio of node density.

Figure 3: Probability of coverage versus sensor nodes, standard deviation .

Figure 4: Probability of coverage versus sensor nodes, standard deviation .

(ii) Effect of Node Failure on Sensing Coverage. Figure 5 shows the probability of 3-coverage with different number of sensor nodes for four different failure probabilities. Here, we consider standard deviation parameter and path loss exponent . it is clear from the figure that when the number of sensor node increases, the probability of coverage also increases even in presence of node failure. When the probability of node failure is high, the slope of the curve is less. This indicates that adding extra nodes does not help much to increase the network coverage as compared to that when the failure probability of node is less.

Figure 5: Probability of coverage versus number of sensor nodes for different failure probability.

(iii) Effect of Node Density on Connectivity. Figure 6 shows the result for -connectivity with nodes. When we deploy 200 nodes in a square region of 100 × 100, the network is almost disconnected. For surely connected network with probability ≥90%, we require approximately 340 sensor nodes. If we deploy 360 nodes in the same area, we will get 3-connected network with probability >90%. Therefore, as the density of the sensor node increases, the graph shows transition from low connectivity to high connectivity.

Figure 6: Probabaility of -connectivity versus number of sensor.

(iv) Effect of Shadowing Parameter on Connectivity. Figure 7 shows the relationship between network connectivity, number of sensor nodes, and standard deviation constant. For surely connected network with probability >90%, we require approximately 360 nodes in the square region of 100 × 100 when there is no fading. If we increase standard deviation constant , less number of nodes are sufficient to make the network connected with same probability. When the standard deviation constant increases then irregularity in the communication range also increases, that is, communication link is more asymmetric. A less number of shorter links are removed and large numbers of longer links are added because the number of nodes increases linearly with distance. Therefore a node which is closer to the communication range may be isolated but in turn some more nodes that are farther away may get connected. As shown in Figure 4, when the Standard deviation , we require 340 nodes, and when the , approximately 296 nodes are sufficient to get network connected with same probability. Hence, the probability of -connectivity increases with the presence of log-normal shadowing.

Figure 7: Probability of network connectivity versus sensor nodes.

(v) Effect of Communication Range on Connectivity. Figure 8 shows probability of connectivity as a function of communication range. Here, we can see the effect of communication range on the network connectivity. The connectivity of the network increases when the communication range of the nodes increases. When the communication range of the sensor nodes is less than 10 m, the network is almost disconnected. As the communication range of the nodes increases from 10 m to 13 m, the connectivity also increases and reaches to approximately 90% for the communication range 13 m and . For less number of nodes and same high probability of connectivity, the communication range is 18 m approximately as shown in Figure 8.

Figure 8: Probability of connectivity versus communication range.

(vi) Effect of Nodes Distance on Connectivity. Figure 9 shows the probability of Connectivity with the distance between two sensor nodes. It can be observed from Figure 6 that, when the standard deviation and distance between two nodes is 11 m then probability of connectivity is almost zero, but when the shadowing increases from 0 to 2 and 4, the probability of the link between two nodes is approximately 60% and 70%, respectively, for the same distance.

Figure 9: Probability of connectivity versus distance.

8. Conclusions

One important QoS parameter in the design of WSN is that the network should be fault tolerance. In this paper -coverage and -connectivity are evaluated under log-normal shadowing model. Further we have studied the random shadowing effects which are incorporated into path loss and better describe received signal strength with distance in real environments. We have also shown the effect of node density and node failure probability on coverage. It has been observed that the probability of network coverage and connectivity depends on the node density and standard deviation. A higher value of standard deviation results in the decrease of average sensing radius of sensor node. Therefore, the probability of network coverage degrades. On the other hand high fading variance adds more links as compared to removed links thus improves connectivity. It can be concluded that log-normal path loss model and node density have a significant impact on coverage and connectivity.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The author, Mr. Anil Kumar Sagar, would like to thank Sh. Sushil Kumar, Assistant Professor, JNU, and Mr. Shrawan Kumar for their valuable comments and suggestions, which were helpful in improving the quality of paper.

References

I. F. Akyildiz, W. Su, Y. Sankarasubramaniam, and E. Cayirci, “Wireless sensor networks: a survey,” Computer Networks, vol. 39, no. 4, pp. 393–422, 2002.

H. M. Ammari and S. K. Das, “Centralized and clustered k-coverage protocols for wireless sensor networks,” IEEE Transactions on Computers, vol. 61, no. 1, pp. 118–133, 2012.

Y. Cai, M. Li, W. Shu, and M.-Y. Wu, “ACOS: a precise energy-aware coverage control protocol for wireless sensor networks,” Ad Hoc and Sensor Wireless Networks, vol. 3, no. 1, pp. 77–98, 2007.

M. Esnaashari and M. R. Meybodi, “Deployment of a mobile wireless sensor network with k-coverage constraint: a cellular learning automata approach,” Wireless networks, vol. 19, pp. 945–968, 2012.

S. He, J. Chen, and Y. Sun, “Coverage and connectivity in duty-cycled wireless sensor network for event monitoring,” IEEE Transactions on Parallel and Distributed Systems, vol. 23, no. 3, pp. 475–482, 2012.

D. Li, J. Cao, M. Liu, and Y. Zheng, “K-connected target coverage problem in wireless sensor networks,” in Combinatorial Optimization and Applications, vol. 4616, pp. 20–31, 2007.

X. Bai, Z. Yun, D. Xuan, B. Chen, and W. Zhao, “Optimal multiple-coverage of sensor networks,” in Proceedings of the IEEE INFOCOM, pp. 2498–2506, Shanghai, China, April 2011.

S. S. Dhillon and K. Chakrabarty, “Sensor placement for effective coverage and surveillance in distributed sensor networks,” in Proceedings of the Wireless Communications and Networking Conference, vol. 3, pp. 1609–1614, 2003.

C. Bettstetter and C. Hartmann, “Connectivity of wireless multihop networks in a shadow fading environment,” Wireless Networks, vol. 11, no. 5, pp. 571–579, 2005.

R. Hekmat and P. Van Mieghem, “Connectivity in wireless ad-hoc networks with a log-normal radio model,” Mobile Networks and Applications, vol. 11, no. 3, pp. 351–360, 2006.

N. Bulusu, J. Heidemann, and D. Estrin, “GPS-less low-cost outdoor localization for very small devices,” IEEE Personal Communications, vol. 7, no. 5, pp. 28–34, 2000.

T. S. Rappaport, Wireless Communications, Principles and Practice, Prentice Hall, 2nd edition, 2002.

G. Zhou, T. He, S. Krishnamurthy, and J. A. Stankovic, “Models and solutions for radio irregularity in wireless sensor networks,” ACM Transactions on Sensor Networks, vol. 2, no. 2, pp. 221–262, 2006.

B. Xiao, H. Chen, and S. Zhou, “Distributed localization using a moving beacon in wireless sensor networks,” IEEE Transactions on Parallel and Distributed Systems, vol. 19, no. 5, pp. 587–600, 2008.

J. Orriss and S. K. Barton, “Probability distributions for the number of radio transceivers which can communicate with one another,” IEEE Transactions on Communications, vol. 51, no. 4, pp. 676–681, 2003.

M. D. Penrose, “On k-connectivity for a geometric random graph,” Random Structures and Algorithms, vol. 15, no. 2, pp. 145–164, 1999.