A Phase-Locked Loop with 30 % Jitter Reduction Using Separate Regulators

A phase-locked loop (PLL) using separate regulators to reject the supply noise is proposed in this paper. Two regulators, REG1 and REG2, are used to prevent the supply noise from the charge pump (CP) and the voltage-controlled oscillator (VCO), respectively. By using separate regulators, the area and the power consumption of the regulator can be reduced. Moreover, the jitter of the proposed PLL is proven on silicon to be less sensitive to the supply noise. The proposed PLL is fabricated using a typical 0.35 μm 2P4M CMOS process. The peak-to-peak jitter (P2P jitter) of the proposed PLL is measured to be 81.8 ps at 80 MHz when a 250 mVrms supply noise is added. By contrast, the P2P jitter is measured to be 118.2 ps without the two regulators when the same supply noise is coupled.


INTRODUCTION
Most mixed-signal circuits need a phase-locked loop (PLL) to generate a stable clock for ADC, DAC, or digital circuits.For example, the receiver of the DVB-T digital television requires an ADC with a sampling clock of 30 MHz for the baseband bandwidth of 8 MHz [1].The jitter of the PLL is considered as a critical factor for the correct data transformation in these applications.Many prior efforts to discuss the reasons as well as the rejection methods of the PLL jitter have been announced [2,3].The main source causing the PLL jitter is the supply noise and the substrate noise [2].Several prior works proposed a variety of methods to reduce the supply noise in order to suppress the jitter [3][4][5][6][7].Two methods are widely used for reducing the PLL jitter caused by supply noise: differential topology [3] and power regulation [4].For example, Maneatis proposed the self-biased techniques with differential structure to achieve a PLL with low jitter, and fixed damping factor [5]. Kaenel proposed a PLL using a high-performance regulator to suppress the supply noise.However, the high-performance regulator has the penalty of large chip area.Besides, the high-performance regulator intrinsically causes design complexity due to the frequency compensation topologies [8].By contrast, this paper proposes a PLL using separate regulated power supplies for the charge pump and the VCO, respectively.By using separate regulators, the area and power cost would be reduced.The physical measurements on silicon verify that the P2P jitter is merely 81.8 ps at 80 MHz with the presence of a 250 mVrms supply noise.

PLL USING SEPARATE REGULATORS
In order to remove the effects of the supply noise, a single-voltage regulator for the charge pump (CP) and the voltage-controlled oscillator (VCO) could be used.The load regulation of a traditional regulator is proportional to the dimension of the pass transistor of the regulator, as shown in where R o-pass (= 1/gm o-pass ) denotes the output resistor of the pass transistor, A OL denotes the open loop gain, and β is the feedback factor.To reject the severe vibration at VCO, it requires efficient load regulation by the regulator.According to (1), the excellent load regulation needs large gm o-pass and A OL .It implies that a large pass MOS transistor is a must.Moreover, by connecting the VCO and the CP, the noise resulting from the vibration VCO might be coupled to the CP, which is supposed to provide a stable driving current.Such a coupling for the VCO and CP is undesirable, because the supply noise will deteriorate the output jitter through the CP.
Figure 1 shows the block diagram of the proposed PLL, which is composed of a 2nd order charge pump PLL and the proposed dual regulators.The transfer function of each block is also revealed in Figure 1.Notably, Vn1 and Vn2 denote the supply noise directly injected into the CP and VCO of the traditional 2nd order charge pump PLL, respectively.Vn1 and Vn2 denote the supply noise coupled to the dual regulators of the proposed dual regulation PLL, respectively.
Regarding the 2nd order charge pump PLL without the dual regulators, the power supply of CP and VCO would be biased at VDD directly.Thus, the supply noise Vn1 and Vn2 would be fed into CP and VCO directly.According to the transfer function of each block shown in Figure 1, the output phase in closed loop can be found to be By setting GH(s) = H3(s)•H4(s)•(K VCO /s), the output phase can be derived to be The output phase φ o is expressed as a function of the input phase φ i , and the supply noise, Vn1 and Vn2.Referring to (3), the low-frequency components of Vn1 would affect φ o 0, and the high-frequency components of Vn1 can be suppressed by the pole of H4(s).Intuitively, Vn1 is lowpassed by the LF.By contrast, Vn2 would not be filtered by the LF and then contaminate the output phase φ o directly.
In order to filter the supply noise, Vn1 and Vn2, and avoid the mentioned area penalty caused by the large pass transistor, the dual regulators are employed in the proposed design, as shown in Figure 1.With the dual regulators, the CP and VCO are powered by REG1 and REG2, respectively.Thus, the supply noise, Vn1 and Vn2 , would be coupled to the dual regulators REG1 and REG2, respectively, and would not directly affect the CP and VCO.Similarly, the closed loop transfer function of the proposed PLL with dual regulators will be where H5(s) and H6(s) denote the frequency response of REG1 and REG2, respectively.H5(s) and H6(s) are the major difference between (3) and ( 4).Moreover, H5(s) and H6(s) would suppress the supply noise Vn1 and Vn2 , respectively.The design of the regulators will be discussed in the following subsection.

Regulators (REG1, REG2)
To reduce the supply noise, the bandgap bias must be insensitive to the supply voltage.Referring to Figure 2, the output voltage VBGAP of the bandgap bias can be expressed as in the following equation: where V EB, PQ101 is the emitter-base voltage of PQ101, V T is the thermal voltage, and n is the emitter area ratio of PQ101 to PQ102.The supply voltage VDD is not included in the expression.Thus, VBGAP is insensitive to VDD.
As mentioned in the previous section, H5(s) of REG1 must suppress the low-frequency noise.In order to filter the low-frequency supply noise, a step-down regulator REG1 can be employed, as shown in Figure 3(a).REG1 is a regulator which is composed of an error amplifier OP301, a pass transistor PM301, and a resistive feedback network R301 and R302.Because Rs = 50 KΩ and Cs = 5 pF are chosen, the LF is treated as a low-pass filter with a pole at 4 MHz.Thus, REG1 must filter the supply noise with frequency below 4 MHz.This requirement can be achieved easily, since the step-down regulator can inherently generate a stable output voltage at low frequencies.
Figure 3(b) shows the schematic of REG2, which is composed of a step-down regulator (including the error amplifier OP401, the pass transistor PM402, and the resistive feedback network R401 and R402) and a low-pass filter PM401 and NM401.According to the previous discussion, H6(s) of REG2 should compress both the low-frequency component and the high-frequency component of supply noise Vn2 .Because the step-down regulator can only suppress the low-frequency supply noise, a low-pass filter is employed at the source of the pass transistor PM402 such that the high-frequency and low-frequency noise components can be filtered.Notably, the MOS resistor PM401 and the MOS capacitor NM401 are used to replace traditional R-C LPF configuration to reduce the area overhead.The gate of PM401 is biased at VBGAP but not biased at GND directly for possessing a high resistance.
In order to sustain the stable output voltage of REG1 and REG2, the loop bandwidth of the regulators must be large enough.The step-down regulators possess three poles, which are the dominant pole contributed by the error amplifier; the gate pole contributed by the parasitic capacitor at the gate of the pass transistor; and the loading pole contributed by the loading current.Because REG1 and REG2 cooperate with the low-pass filters, the output current is smoothed.Thus, the loading pole can be ignored.Besides, the gate pole can

PFD
The deadzone is the most important parameter for PFD because it is the major source of the PLL phase error.CLK OUT, respectively.The two-stage structure carries out the precharge function such that high speed is achieved.The feedback control signal for PM602 and NM601 for UP (similarly, PM605 and NM605 for DN) makes the zero deadzone possible.Moreover, the drawback of a short-circuit current from VDD to GND is eliminated because PM602 and NM601 for UP (similarly, PM605 and NM605 for DN) do not turn on at the same time [10].

CP
REG1 is in charge of the noise rejection for CP.Besides, the switching speed of CP is another important source for the PLL jitter.Thus, a switch is placed in the source of the mirrored MOS transistors for the speed consideration in Figure 5 [11], where PM801 (NM803) is the switch of current, PM803 (NM801) is the mirrored current source, PM802 and PM806 (NM802 and NM806) are for the charge injection reduction, PM804 and NM804 (PM805 and NM805) consist of a dummy delay element for eliminating the skew of the control signal, and UPB and DNB are the inversions of UP and DN, respectively.Thus, the control signals, UPD, UPB, DNB, and DND, can be activated without any time delay.Notably, the output current of the bias generator for CP shown in Figure 6 is ideally independent of the supply voltage.

VCO
The current-starved inverters are used to construct the VCO, as shown in Figure 7.With the current-starved structure, the supply noise would contaminate the output phase.Referring to (6), the output frequency can be assumed to be in terms of the RC delay and n denoting the number of the inverter stages.C tot denotes the total parasitic capacitance including wire parasitic capacitor (C wire ), and drain-to-bulk capacitor (C DB ).For simplifying the analysis, C DB is assumed to be a constant regardless of the operation mode of the transistors.Moreover, the resistance of the channel of each stage (R) could be estimated as the reciprocal of the transconductance of the MOS.With φ o = ∂ f o /∂t, the supply noise would change the V GS of the PMOS and further affect the output frequency and output phase: where V TH denotes the threshold voltage.The serious problem of supply noise coupled in the current-starved VCO will be resolved by REG2.Besides, the output buffer is added to maintain the gain of VCO when a large capacitive load is present.

IMPLEMENTATION AND MEASUREMENT
A typical 0.35 μm 2P4M CMOS process is adopted to carry out the proposed PLL design.The die photo of the proposed PLL is shown in Figure 8 where the core area is 705 μm × 732 μm.The total area including the PADs is 1.118 mm × 1.462 mm.In order to guarantee the functionality of the power regulators addressed in Section 2, the guard ring to reject the substrate noise from PLL to regulators must be added between the REG1, REG2, and the PLL.The PSRR of the regulator is simulated to be 26.2 dB.Three 10 mV sinusoidal waves with 100 Hz, 100 KHz, and 80 MHz frequencies, respectively, are coupled at the power supply to be the supply noise.With this dirty power supply, the simulated P2P jitter is 93.777 ps at the worst case simulation corner of SS model.The power consumption of the proposed PLL is simulated to be 15.857 mW at 80 MHz operating frequency.
The measurement environment of the PLL chip is set up on a PCB board.The quartz oscillator for the reference clock is HO-12B of HOSONIC ELECTRONIC CO., LTD.The power supplier is GW GPC-3030D.Agilent Infiniium Oscilloscope, 600 MHz, 4 GSa/s, is employed in recording the PLL jitter of the chip.The output waveform is 80 MHz,  as shown in Figure 9.The rise time and fall time are 3.1422 nanoseconds and 2.7747 nanoseconds, respectively.The equivalent load capacitance of the probe is 8 pF.
Figure 10 shows the measured jitter histograms in different conditions.The supply noise of 250 mVrms generated    more than 30% than that without the dual regulators.It shows that the method of using two regulators can reduce the supply noise that affects PLL's output jitter.Besides, the P2P jitter is measured to be 72.7 ps when no supply noise is coupled to the dual regulators or to the CP and VCO directly.The total power consumption of the proposed PLL is 78 mW at 80 MHz.Notably, the measured power consumption includes the power due to the I/O PADs such that the measured power consumption is larger than that based on simulation.Besides, a performance comparison of the proposed design on silicon with several prior PLLs are summarized in Table 1.Notably, the P2P jitter of the proposed design is 43% better than that of Maneatis's design [5].It seems to take the penalty of 8.44 times of power consumption.However, the power consumption of 78 mW of the proposed design includes the excess power consumption of the PADs.Thus, the penalty of power consumption is not really serious.Two figures of merit (FOMs) are given to normalize the performance of those works.FOM1 is the normalization for the power consumption, as shown in where C is to indicate the capacitor's area which can be assumed to be proportional to the square of the feature size of the corresponding process (S).With the normalization, the PLL using self-biased and differential structure consumes the least power.However, the jitter performance is not good enough.On the other hand, FOM2 (= A/S 2 ) is to compare the area with respect to the feature size of the corresponding CMOS process.The normalized area of the proposed PLL is revealed to be better than that of the other works.

CONCLUSION
We have proposed a PLL with two regulators to isolate the supply noise for CP and VCO, respectively.The measurement results verify that the proposed design can reject the supply noise into the output jitter of the PLL.The jitter can be reduced by more than 30% using the proposed design according to the measurement on silicon.

Figure 1 :Figure 2 :Figure 3 :
Figure 1: The block diagram of the proposed PLL.

Figure 8 :
Figure 8: The die-photo of the proposed PLL.

Figure 9 :
Figure 9: The measured output waveform of the proposed PLL at 80 MHz and an 8 pF load from the probe.

Figure 10 :
Figure 10: The measurement jitter histogram of the proposed PLL with the 250 mVrms supply noise.(a) The supply noise is provided to the dual regulators.(b) The supply noise is coupled directly to the CP and the VCO.

Table 1 :
Performance comparison of the proposed PLL and prior works.: FOM1 = P/( f S 2 Vsp 2 ), FOM2 = A/(S 2 ), where S is the feature size of the process.: Assume that the power consumption is measured at the maximum operating frequency. #