Investigating the Effect of the Rock-Socketed Depth of the Hinged Cable-Anchored Pile on the Earthquake Response Characteristics of Supporting Structures

In order to meet the design requirements of the anti-slide pile, the form of the anchor-pull pile is often adopted in engineering applications. In the present study, the seismic response characteristics of hinged cable-anchored piles with dierent rock-socketed depths are analyzed using a large-scale seismic model test platform and numerical simulations. e obtained results show that the rock-socketed depth signicantly aects the seismic response of the pile-anchor system. It is found that, as the rock-socketed depth increases under the same seismic conditions, the peak acceleration at the top of the anchored pile, the peak dynamic Earth pressure behind the pile, the axial force of the anchor rod, and the bending moment of the pile body decrease and the seismic stability of the anti-slide pile improves. It is concluded that, in the seismic design of anchor-pulled piles, increasing the rocksocketed depth of the anchor is an appropriate scheme to improve the seismic performance of anchor-pulled piles. e research results have a certain signicance for improving the understanding of the seismic response law of hinged cable-anchored piles and improving the seismic design.


Introduction
Studies show that the rock-socketed depth of the anchor section is an important parameter that a ects the anti-slide pile design, thereby a ecting the whole supporting system. When the rock-socketed depth is insu cient, the anti-slide pile will not have su cient resistance to the thrust load of the sliding body and will easily fail. Excessive rock-socketed depth, on the contrary, imposes additional engineering expenses and increases the construction di culty. Accordingly, obtaining a safe and economical rock-socketed depth has become one of the most concerning issues for geotechnical engineers. In this regard, many investigations have been carried out on anti-slide piles. However, most scholars have focused on the load-bearing mechanism and pile-soil interaction under static conditions and calculating the anchorage depth [1][2][3][4][5][6][7][8][9][10][11]. For example, Jiang et al. [12] studied rigid piles in di erent conditions and proposed an expression to calculate the anchorage depth of the rigid pile. Although the proposed expression yields promising achievements, there are some limitations. Moreover, Chunmei and Yin [13] determined di erent embedded depths by changing the structural form and section size of the antislide pile. However, since the in uence of rock characteristics of the embedded section was not considered in the calculations, the proposed expression had certain limitations. Hu and Wang [14] demonstrated that the anchorage depth of an anti-slide pile is a ected by random variables and used the cantilever pile method to calculate the anchorage depth of a rigid anti-slide pile. Based on the lower limit theorem of the plastic limit analysis, Ting-kai et al. [15,16] derived analytical solutions for active and passive Earth pressure before and after the anti-slide pile, determined the lateral allowable bearing capacity of the soil around the anti-slide pile, and calculated the anchorage depth of the elastic anti-slide pile. Wu K. [17] established the reliability analysis model to calculate the anchorage depth of rigid piles based on the strength reduction finite element method. Zhang et al. [18] considered different parameters in calculations and established a model to analyze the anchorage depth of rigid piles. Yuan-you et al. [19] introduced the nonlinear optimization theory in the optimal design of anti-slide piles. Furthermore, Chen and Xiao [20] derived an expression to calculate the allowable resistance at the side soil of an anti-slide pile in the anchor section and determine the optimum anchorage depth.
Reviewing the literature indicates that most investigations on the seismic dynamics of anchor-drawn anti-slide piles have focused on the structural responses [21][22][23][24][25][26][27][28][29]. ese investigations are often carried out using numerical simulations and physical tests [30][31][32][33][34][35][36][37][38][39]. For example, Kong et al. [40] studied the embedded depth of anti-slide piles under the action of earthquakes and determined the optimal embedded depth of anti-slide piles in gravel soil. Currently, there is a lack of knowledge on the difference in response characteristics of anchorage piles caused by different rock-socketed depths in anchorage sections under the action of an earthquake.
Anti-slide pile with hinge support at the base refers to an anti-slide pile with complete basement strata but a small rock-socketed depth where the pile bottom is supported with a hinge. In order to control the displacement of the pile top and limit the lateral wall stress of the anti-slide pile to the lateral allowable compressive strength, anti-slide piles are usually anchored. In practical applications, the slope reinforced with prestressed anchor cable and anti-slide piles has a reasonable seismic capability [41,42]. e main objective of the present study is to investigate the performance of hinged-supported anchor piles and the ground motion response characteristics of its support structure under different rock-socketed depths. To this end, tests are carried out on the seismic shaking table and numerical simulations are performed to develop the anti-slide design method of the hinged-supported anchor pile.

Similarity Principle.
According to similarity criteria [43], physical variables can be mainly divided into three categories, including general geometric similarity, dynamic similarity, and kinematic similarity. General geometric similarity refers to elementary geometric similarity, where a specific length is generally taken as the dimension of physical variables. Combining similar characteristics of various physical systems, the positions and significances of three categories can be described as if any two systems that are similar in geometry, dynamics, and kinematics have similar performances. It is worth noting that geometric similarity can be simply achieved, while the kinematic similarity is achieved only when geometric and dynamic similarities are achieved simultaneously. erefore, the kinematic similarity is the most challenging one among the three similarities. Meanwhile, under the condition of geometric similarity, an arbitrary solution obtained from the dynamic similarity satisfies the kinematic similarity.
Pursuant to these principles, geometric similarity and dynamic similarity of the anchor pile support landslide were taken as the basic conditions in this model. Due to limited data, including the selection criteria, about the characteristics of the prototype material, it is a challenge to achieve a complete similarity between the materials of the model and the prototype. Consequently, it is a challenge to achieve consistency between the test results and the prototype failure results. erefore, law similarity was taken as the basic criterion in the model test.

Experimental Equipment and Model
Making. In the present study, the 3-DOF shaking table of Yunnan Institute of Engineering Aseismic with dimensions of 4 m × 4 m was used in all tests. In this table, the maximum load is 30 tons. Moreover, the maximum displacement and velocity are 250 mm and 0.8 m/s, respectively. e maximum acceleration is 1 g under a load of 20 tons, while it reduces to 0.8 g when the load increases to 30 tons. e operating frequency can be set in the range of 0 ∼ 100 Hz and the maximum overturning moment is 30 tm. e whole test consists of many materials, including landslide materials, model box, retaining plate, anti-slide pile, anchor rod, and concrete. e landslide model is made of three parts, including the sliding bed, sliding surface, and sliding body. Silty clay is used as the soil during tests and the sliding-bed soil is compacted. When making the sliding surface, the soil is first screened with a sieve of about 2 mm in diameter, and then, it is dried. In this way, impurities are picked out and 50% of the fine sandy soil is mixed. e prepared sliding surface soil is evenly distributed over the sliding bed with a thickness of 5 cm. e silty clay is used as the slime soil. It is worth noting that instead of sieving, drying, and tamping, the silty clay is stacked above the slime surface and leveled evenly in the present study. e bedrock of the anchoring section of the anti-slide pile is made of C40 concrete. Table 1 shows the physical and mechanical properties of the test materials. e studied anti-slide pile is made of wood and has a cross section of 80 mm × 80 mm and a length of 60 cm. e bottom part of the anti-slide pile is placed in the concrete cast in a steel channel to simulate the rock-socketed depth. e schematic of the model is shown in Figure 1.
2 Advances in Civil Engineering Figure 2 shows that an acceleration sensor is arranged on the pile top to measure the acceleration and convert the displacement of the pile top into xxx. Moreover, strain gauges are arranged on four sides of the anchor cable 0.08 m from the retaining plate to measure the axial force. Figure 3 shows the installed acceleration sensors.
In all experiments, El seismic Centro waves are used. It is worth noting that the El Centro wave is extensive and representative, which is of great significance for seismic research. In this regard, studies show that the horizontal component of the seismic wave reflects the fundamental force that causes the crack propagation and even failure of the landslide and its retaining structure. During the tests, 5 seismic conditions were designed to simulate a 7-degree medium earthquake, 8-degree medium earthquake, 8-degree large earthquake, 9-degree large earthquake, and over 9-degree earthquake. Figure 4 shows that the control peak of horizontal acceleration in each test condition is 0.1 g, 0.2 g, 0.4 g, 0.62 g, and 1.0 g, respectively.
e data of slope acceleration, pile tip displacement, and anchor shaft force are collected. Figure 3 shows that an acceleration sensor is installed on the top of the anti-slide pile to measure the seismic acceleration response of the pile under the action of an earthquake. e pile top displacement under five working conditions is obtained using the quadratic integration. en, the pile top displacement of seismic waves was analyzed, and the results are presented in Table 2. Figure 5 illustrates the displacement at the pile top under different working conditions and the same hinge support. It is observed that the peak displacement of the three anchor piles with different rock-socketed depths increases with the increase of the acceleration of the input seismic wave. When the acceleration peak value of the input seismic wave varies  Advances in Civil Engineering from 0.1 g to 0.6 g, the displacement peak value increases linearly, and then, it decreases when the acceleration exceeds 0.6 g. It is found that, as the acceleration peak of the input seismic wave increases, the corresponding pile-anchor-soil interaction becomes more significant. e comparison of displacements at the top of the anchor-pull pile with different rock-socketed depths reveals that the rock-socketed depth affects the displacement of the top of the anchor-pull pile under the same seismic condition. More specifically, the biggest peak displacement occurs in anchor-pull pile No. 1 with a rock-socketed depth of 5 cm, while the lowest peak displacement occurs in the anchor-pull pile No. 3 with a rock-socketed depth of 15 cm. e stress mechanism of the anti-slide pile with hinged bearing is analyzed to interpret these results. e schematic diagram of the anti-slide pile with a hinged bearing in Figure 6 can be characterized by the integrity of the rock stratum at the bottom of the pile and the hard rock in section AB. However, the embedded pile in this layer is not deep, so the displacement and the bending moment at point B are x B � 0 and M B � 0, respectively. When the base of the pile is the hinge end, the displacement and rotation angle at point A can be calculated using the following expression:

Seismic Displacement Response.
Equation (1) indicates that the height h of the segment AB decreases with the increase of the rock-socketed depth of the anti-slide pile under the hinged bearing, which is equivalent to the decrease of the effective arm of the antislide, decrease of the bending moment M A , and the displacement of the rotation angle at point A. Finally, the experimental results are verified with the theoretical results.

Strain
Response of the Bolt. In this section, axial strain peaks of three bolts embedded in rock with depths of 5 cm, 10 cm, and 15 cm under different working conditions were statistically analyzed, and the results are presented in Table 3. Figure 6 schematically presents the pile diagram. Figure 7 shows that, as the rock-socketed depth of anchor piles with hinged supports under the same seismic conditions increases, the corresponding strain of the anchor rod decreases. is may be attributed to the elongation of the anchor cable, which is equal to the horizontal displacement of the pile. is analysis is also consistent with the achieved conclusions in the previous section regarding the seismic displacement response.
e obtained results indicate that, under different seismic conditions, as the peak acceleration of the input seismic wave increases, the corresponding strain values of the anchor rod increase at different rock-socketed depths. It is inferred that, with the increase of the peak acceleration of the input seismic wave, the pile-anchor-soil interaction becomes more significant. ese results are also consistent with the conclusions of the seismic displacement response in the previous section.

Validation of Numerical Simulation Analysis
In this section, Fast Lagrangian Analysis of Continua in 3-Dimension (FLAC3D) software, which is a powerful tool to perform geotechnical analyses of soil, rock, groundwater, constructs, and ground support [44][45][46], is applied to carry out numerical analyses. Such analyses include engineering design, setting the safety factor, analysis of the test results, and back analysis of failures. In this software, the governing equations are solved using an explicit finite volume method to study the complex behaviors of models. Calculations in this software mainly consist of several stages, including detecting large displacements and strains and calculating nonlinear material behavior, yield/failure over large areas, and total collapse. Studies show that Flac3D software has remarkable advantages. First, it uses the "mixed discrete method" to simulate plastic failure and plastic flow. It is worth noting that this method is more accurate than the "discrete integration method," which is usually used in the finite element method [xx]. Second, even though the   Advances in Civil Engineering simulated system is static, the dynamic equations of motion should be solved, which makes FLAC3D have no numerical obstacles in simulating the physically unstable process. Last, it adopts an explicit solution scheme. erefore, the explicit solution takes almost the same time to obtain the nonlinear stress-strain relation as the linear constitutive relation, while the implicit solution takes a longer time to solve a nonlinear problem. Meanwhile, there is no need to store the stiffness matrix so multielement structures can be solved with less memory capacity. erefore, it is feasible to simulate large deformations because there is no stiffness matrix to be modified. Accordingly, the FLAC3D software is selected in the present study to analyze the problem. To avoid being affected by boundary conditions, three models are established in this numerical simulation. Each model has three anti-slide piles. e rock-socketed depths of the three models are 5 cm, 10 cm, and 15 cm, respectively. In each model, the anti-slide pile in the middle position was selected for data analysis. Table 4 shows the physical and mechanical parameters of the studied materials. During calculations, the retaining plate, anti-slide pile, and anchor rod were considered elastic materials to improve the calculation accuracy and efficiency.
e whole 3D dynamic model is divided into 30,000 elements. e meshed model is shown in Figure 8.

Analysis of the Acceleration Response.
ree anti-slide piles are established in each model, and the accelerationtime curve is obtained at the top of the anti-slide piles at the middle position. Figure 9 reveals that, under the same conditions, the largest and the smallest peak accelerations occur at the top of the anchor-pull pile with a rock-socketed depth of 5 cm and 15 cm, respectively. It is found that, as the rock-socketed depth increases, the corresponding peak acceleration at the top of the anchor-pull pile decreases. is is also consistent with that obtained results from the shaking table test.

Response of Dynamic Earth Pressure behind the Pile.
In the three models, the anchor piles at the middle position are selected to monitor the dynamic Earth pressure along the       6 Advances in Civil Engineering x-direction at the position of 45 cm behind the piles. Figures 10 and 11 show the time-history curves of dynamic Earth pressure for anchor piles with different rock-socketed depths under the same seismic conditions. e peak values of dynamic Earth pressure are presented in Table 5. Figures 10-12 show that the dynamic Earth pressure peak of anchor piles have the same trend under the same seismic conditions, and they are all active Earth pressure; the change of Earth pressure is corresponding to the change of peak acceleration of the ground motion. e dynamic Earth pressure balances with the increase of the earthquake time history. Table 5 and Figure 13 reveal that, as the rocksocketed depth increases, the peak value of the passive Earth pressure after the anchor-pull pile decreases. More specifically, the largest and the smallest peak value of active Earth pressure after the anchor-pull pile occurs with a rocksocketed depth of 5 cm and 15 cm, respectively. It is found that the displacement of the pile head is limited by the increase of the rock-socketed depth, which is verified by the corresponding conclusions of the pile top displacement and anchor stress in the model test.

Axial Force Response of the Anchor Rod.
ere are three anchors with the same inclination angle and the middle anchor piles are selected to analyze numerically. Axial force monitoring points are set on each bolt, and the time-history curves of the axial force under the same seismic condition are shown in Figures 14-16. Peak axial forces of the anchor rod are presented in Table 6. Figures 14-16 and Table 6 show that the time-history curves of axial force values of the three bolts have the same changing trend. Moreover, the comparison of the peak axial force between Table 6 and Figure 17 reveals that the axial force of the anchor rod decreases with the increase of the  1.00 2.00 3.00 Step ×10^6 Y-Axis ×10^6 (Pa) 4.00 5.00 6.00 1.00 2.00 3.00 Step ×10^6 Y-Axis ×10^6 (Pa) 4.00 5.00 6.00     Step ×10^6 Y-Axis ×10^3 (N) 4.00 5.00 6.00  Step ×10^6 Y-Axis ×10^3 (N) 4.00 5.00 6.00    Advances in Civil Engineering different rock-socketed depths is analyzed and the results are presented in Figure 18. Figure 18 shows that, under the same seismic conditions and at the same height, different rock-socketed depths result in different peak moment values in the anchor pile. e maximum bending moment time curve of the anchor-pull piles No. 1

Conclusions
In the present study, the seismic response characteristics of the anchor pile with hinged support at different rocksocketed depths are studied using a large-scale seismic model test platform and numerical simulations. Based on the obtained results, the main conclusions can be summarized as follows: (1) e rock-socketed depth has a significant impact on the seismic response of anchor piles. It is found that, under the same seismic condition, the peak acceleration at the top of the pile, the peak dynamic Earth pressure behind the pile, the axial force of the anchor rod, and the bending moment of the pile decrease with the increase of the rock-socketed depth. is is because the effective force arm and bending moment of the anti-slide pile, and the displacement and rotation angle of the anti-slide pile decreases with the increase of the rock-socketed depth. (2) With the increase of the acceleration peak value of the input seismic wave, the pile-anchor-soil interaction becomes more significant. e performed analyses demonstrate that the displacement of the pile top is limited by the anchor cable.
(3) Increasing the rock-socketed depth improves the seismic stability of the anti-slide pile. is is a promising way to improve the seismic performance of the anchor-pull pile with hinged support. e studied test model for the seismic response of the anchor pile retaining structure subjected to the earthquake load is an effective way to understand the dynamic interactions between the pile-anchor and the pile-soil mass and can provide theoretical support for the seismic design of the slope. However, the dynamic interactions between the pile and soil are complex and further investigations are required in this area.

Data Availability
e data used to support the findings of this study are included within the article.

Conflicts of Interest
e authors declare no conflicts of interest, financial, or otherwise.

Authors' Contributions
Fayou A. and Mingchang Hei are contributed equally to this work.    Advances in Civil Engineering 9