Advances in Materials Science and Engineering

Volume 2013 (2013), Article ID 585714, 7 pages

http://dx.doi.org/10.1155/2013/585714

Research Article

Experimental Study of Correlation of Mechanical Properties of Al-Si Casts Produced by Pressure Die Casting with Si/Fe/Mn Content and Their Mutual Mass Relations

Marcel Fedak, Miroslav Rimar, Ivan Corny, and Stefan Kuna

Faculty of Manufacturing Technologies with Seat in Prešov, Department of Process Technology, Sturova 31, 080 01 Prešov, Slovakia

Received 12 June 2013; Revised 11 October 2013; Accepted 11 October 2013

Academic Editor: Jainagesh Sekhar

Copyright © 2013 Marcel Fedak et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

The submitted contribution addresses problems concerning influence of alloying elements (Si/Fe/Mn) of Al-Si pressure die casts (HPDC) on values of residual deformation. On the basis of results of executed experiments, mutual correlations are analyzed and described, while not only measurements results are evaluated but also metallographic outputs of obtained compounds from the view of their formation, occurrence, and size. The development of intermetallic phases structures Al(FeMn)Si as well as intermetallic ferritic phase Al₃FeSi was observed. More verification experiments follow in order to apply obtained knowledge for improvement and/or preservation of casts properties on required level.

1. Introduction

Parts manufactured by pressure die casting distinguish by suitable properties in relation to their mass. In present, these products/casts are utilized in various spheres of industries, significant share of which is automotive industry [1]. An important requirement in this sphere is resultant mass of products, whilst all claimed properties are preserved. The trend of mass reduction leads to application of aluminium-based materials, while demands on strength, extensibility, and other mechanical properties are on the same level as for Fe-based materials.

The paper describes basic impacts of chosen alloying elements on permanent deformation as a significant mechanical property. Mutual correlations between chosen alloying metals and resulting deformation measured on a group of casts are described. Consecutively these relations are observed during variation of content of the alloying elements in order to increase resulting strength of the cast. Providing stability in casting process is of great importance, since it has direct impact on resulting cast properties [2–4]. Aluminium alloys are die cast under pressure on casting machines with cold chamber [5, 6]. Significant factor of the process is corrosive effect of liquid aluminium alloys particularly at higher temperatures, this effect makes it impossible to employ casting machines with hot chamber [6–8]. Horizontal cold chambers are relatively simple, and it is possible to apply higher specific pressure on the cast metal. Thus, it is possible to cast light-walled casts with smooth surface and high mechanical properties. These advantages of horizontal chamber make it possible to design large casting machines with voluminous loading chamber and closing force up to 30 MN, with gross cast mass 30 kg or more, in casting of aluminium alloys (charge utilization of 80%) [6, 9, 10].

The quality of aluminium casts produced by pressure die casting depends closely on the content of alloying elements [5, 6, 11–15]. The properties of chosen alloying elements are described in Table 1.

Table 1: Characteristic, properties, and impact of chosen alloying elements [11, 12, 14–20].

Element
Characteristic

B
Content refines structure and increases electrical conductivity in technically clean aluminium due to precipitation of V, Cr, Mo, and Ti from solid solution

Bi
Alloying with this element improves mechanical machinability

Sb
It serves for improving of corrosion resistance in salty water solutions; in Al-Mg compositions decreases tendency to crack generation

Cr
Alloying with this element decreases susceptibility of grain growth in Al-Mg alloys; in hardenable alloys it increases hardening capacity

Cu
It decreases solidification shrinkage and enables thermal hardening; undesirable effect is a decrease in corrosion resistance; most often it is used along with Mg

Co
In some Al-Si alloys with Fe present, it is added to transform needle-shape phase rich in iron into sphere morphology; this improves strength and plastic properties

Fe
In Al-Si alloys, it occurs as an impurity; solubility in solid state is low (approx. 0.04%); due to this, it is present in structure as intermetallic compound with aluminium Al₅FeSi; in Al-Cu alloys it creates intermetallic compound Al₇FeCu₂, thus reducing copper content in solid solution which leads to a decrease of strength properties

Mg
It is alloyed in order to increase strength properties by hardening formation of intermetallic compound Mg₂Si; it deteriorates fluidity and improves machinability

Mn
It is alloyed into aluminium alloys in order to improve strength, to increase recrystallization temperature, to refine grains, to block grain growth in the case of its segregation in form of disperse precipitates, and to suppress iron segregation in lamellar form; for elimination of harmful iron influence, it is usually added in half content of the iron content

Mo
It is alloyed up to 0.3% in order to refine structure

Ni
It is alloyed in order to improve strength of Al-Cu, Al-Si alloys at higher temperatures; it improves corrosion resistance

Si
In Al-Si alloys, it is the main alloying element, presence of which improves casting properties; comparing with properties of pure aluminium, depending of silicium content, strength is increased

Ti
It is alloyed together with B in order to refine structure

Concentration of alloying elements in the cast is chosen according to requirements on the cast properties; however, the concentrations are limited by recommended ranges [11].

Iron and silicium are very often contained in aluminium alloys. Both of these elements influence mechanical properties of the casts. Theoretical knowledge shows that iron content higher than 1–1.4% has negative impact on the cast properties [5, 6, 11].

2. Materials and Methods

2.1. Preparation of Experimental Casts

Casting machine CLH 400.01 was applied for the experimental casting. It is horizontal pressure machine with cold chamber, with manual dosing of metal. Other operations of casting process run in semiautomatic cycle, so that all conditions of casting cycle could be replicated. In semiautomatic regime of the machine with horizontal cold chamber, an operator manually scoops up metal with the scoop from the heating furnace and pours it into loading chamber. All other operations including ejection of the cast from the mould are automatic with electrohydraulic safety system for particular operations.

Set of 80 specimens were cast at a given technological order (Table 2). Every eighth cast specimen were selected for experimental evaluation, so that the whole range of usable capacity of the heating furnace would be represented.

Table 2: Technological order and casting parameters.

Basic pressure
 MPa

Path of third velocity
270 mm

Third velocity
2.5 rev.

Chamber diameter
60 mm

Size of pellet
25 mm

Temperature of meltage
660 ± 20°C

Insert under the chamber
40 mm

Dose mass into chamber
1300 g

Dosing scoop number
5

Cycle time
50.42 s

Solidification time
4 s

Pressing time
5 s

Unload discharge time
2 s

2.2. Evaluation Method by Pressure Tests of Residual Deformation

This is a type of pressure test which follows residual deformation; the term residual deformation means deformation measured at partial unload discharge. The load is evoked by force . When maximal value of deformation evoked by this force is reached, the value of the force is decreased to value . Time of force effect is usually 10 s.

It holds true that

Residual deformation tests were carried out on device TIRA test 28200. Initial load force was set on value  kN with loading speed 10 mm s⁻¹. When maximum deformation value was reached, the load was decreased to the value  kN, at which the residual deformation was observed during 10 s. Measurements were carried out on ten specimens, courses were recorded and processed by system TIRA test. Ambient temperature during tests was kept at °C.

2.3. Observing Chemical Composition of the Casts

Analysis of chemical composition was observed on spectrophotometer SPECTROLAB JR.CCD 2000. Measurements provided chemical compositions of the casts in the place of openings (A, B). The samples were detached in such a way that no thermal impacts have occurred. Surfaces were adjusted by milling technology. Shape of the samples was formed to achieve square plane with a side of 20 mm. Three measurements for every sample were carried out according to procedure for chemical composition measurements by spark erosion.

The analysis of the casts provides mass content percentage of the following elements: Si, Fe, Cu, Mn, Mg, Zn, Ni, Cr, Pb, Sn, Ti, Na, Sr, V, Zr, and Al. Table 3 shows values of boundary intervals of contents for particular elements according to the norm STN EN 42 4331.

Table 3: Intervals of contents of particular elements as stated by the norm STN EN 42 4331.

Si (%)
Fe (%)
Cu (%)
Mn (%)
Mg (%)
Zn (%)
Ni (%)
Cr (%)
Pb (%)
Sn (%)
Ti (%)
V (%)
Al (%)

Min.
8.00
0.60
2.00
—
0.05
—
—
—
—
—
—
—
—

Max.
11.00
1.10
4.00
0.55
0.55
1.20
0.55
0.03
0.35
0.25
0.25
—
—

3. Results

3.1. Chemical Composition

The results of chemical composition measurements have shown decrease in the content of observed elements in casting process. Particular casts indicate variations of the contents with decreasing tendency. The results directly correspond to the results of observation of content changes in heating furnace that are described in contributions dealing with casting process variations [21, 22]. The results are given in Table 4.

Table 4: Values of chemical compositions of particular cast samples and values of residual deformation.

Sample
Si (%)
Fe (%)
Cu (%)
Mn (%)
Mg (%)
Zn (%)
Ni (%)
Cr (%)
Pb (%)
Sn (%)
Ti (%)
V (%)
Al (%)
Def. (mm)

A1
9.87
0.91
2.27
0.28
0.14
0.74
0.06
0.03
0.12
0.04
0.03
0.01
85.50
0.293

B1
9.88
0.89
2.31
0.27
0.13
0.76
0.06
0.03
0.12
0.04
0.03
0.01
85.48
0.290

A2
9.72
0.87
2.24
0.26
0.14
0.74
0.06
0.03
0.12
0.04
0.03
0.01
85.74
0.296

B2
9.76
0.88
2.22
0.27
0.13
0.74
0.06
0.03
0.12
0.04
0.03
0.01
85.71
0.292

A3
9.72
0.87
2.29
0.26
0.13
0.76
0.06
0.03
0.12
0.04
0.03
0.01
85.68
0.295

B3
9.51
0.86
2.2
0.27
0.12
0.74
0.06
0.03
0.11
0.04
0.03
0.01
85.99
0.291

A4
9.49
0.87
2.24
0.27
0.13
0.75
0.06
0.03
0.12
0.05
0.03
0.01
85.95
0.316

B4
9.39
0.85
2.21
0.25
0.13
0.73
0.06
0.03
0.12
0.04
0.03
0.01
86.14
0.313

A5
9.41
0.83
2.24
0.25
0.13
0.74
0.06
0.03
0.12
0.05
0.03
0.01
86.08
0.312

B5
9.48
0.85
2.24
0.25
0.13
0.74
0.06
0.03
0.12
0.05
0.03
0.01
86.00
0.311

A6
9.3
0.82
2.19
0.25
0.14
0.76
0.06
0.03
0.12
0.05
0.03
0.01
86.20
0.327

B6
9.47
0.85
2.21
0.25
0.14
0.76
0.06
0.03
0.12
0.05
0.03
0.01
86.02
0.305

A7
9.49
0.85
2.22
0.24
0.13
0.75
0.06
0.03
0.12
0.04
0.03
0.01
86.03
0.316

B7
9.41
0.83
2.16
0.25
0.13
0.75
0.06
0.03
0.11
0.04
0.03
0.01
86.19
0.306

A8
9.32
0.81
2.25
0.22
0.13
0.75
0.06
0.02
0.12
0.05
0.03
0.01
86.23
0.334

B8
9.28
0.83
2.24
0.23
0.13
0.75
0.06
0.02
0.12
0.05
0.03
0.01
86.25
0.338

A9
9.34
0.81
2.28
0.22
0.13
0.75
0.06
0.02
0.12
0.05
0.02
0.01
86.19
0.331

B9
9.23
0.79
2.21
0.23
0.13
0.76
0.06
0.02
0.12
0.05
0.03
0.01
86.36
0.336

A10
9.44
0.81
2.25
0.23
0.13
0.75
0.06
0.03
0.12
0.05
0.03
0.01
86.09
0.33

B10
9.32
0.8
2.24
0.22
0.13
0.73
0.06
0.03
0.12
0.04
0.04
0.01
86.26
0.323

From measurements of the chemical composition of each sample (Table 4), the track of changes to the content of the particular elements, depending on the time, can be kept. These changes are directly reflected in the element content of castings, and interval of the change is 7.04% for Si, 15.19% for Fe, and 27.27% for Mn.

On the basis of the analysis, it was suggested to stabilize or slightly increase iron content and to directly increase manganese content. An iron content should be up to one percent because—as it is given in the theory and also prescribed by the norm—exceeding of iron content above 1.4% causes strong negative effects [6, 11]. Relation of iron and manganese content was determined on the basis of measurements to 3.15 : 1. According to this relation and to cast manufacturer requirements, also taking into account possibilities to change alloy composition, the iron content for further experimental evaluation was set on value 0.90 to 0.95% Fe, and the manganese content was set 0.35% to 0.38% Mn.

The experiment that followed was based on suggested iron and manganese content values. The set of casts was produced with the same methodology as in previous case. Six casts from the set were selected for residual deformation and chemical composition analyses. Obtained values are shown in Table 5.

Table 5: Obtained content values of chosen elements (Si/Fe/Mn) of particular samples of the casts and values of residual deformation after content correction of Fe-Mn.

Sample
Si (%)
Fe (%)
Mn (%)
Def. mm)

A11
9.5
0.95
0.35
0.284

B11
9.58
0.98
0.35
0.282

A12
9.26
0.94
0.35
0.287

B12
9.46
0.96
0.34
0.284

A13
9.22
0.91
0.3
0.29

B13
9.34
0.94
0.34
0.29

A14
9.18
0.94
0.32
0.293

B14
9.3
0.93
0.32
0.293

A15
9.07
0.91
0.31
0.294

B15
9.24
0.91
0.31
0.296

A16
9.06
0.87
0.3
0.296

B16
9.17
0.86
0.3
0.298

Dependence courses of particular casts on chemical composition on casting order of the casts are given in Figure 1.

(a)

(b)

(c)

Figure 1: Values of chemical composition (Si/Fe/Mn) for the experiments.

3.2. Residual Deformation

In this part, dependence courses of residual deformation on chemical composition of the casts are observed. Particular influences of chosen alloying elements are given in introductory part of the paper. An influence of iron and manganese on resulting residual deformation was observed, at the same time, a possible influence of silicium content variation was evaluated. Considering that Si influences fluidity, all observed casts were X-ray tested, and no internal defects were detected. Also, visual and dimensional inspections did not show any negative changes of the casts. Figure 2 gives dependence courses of residual deformation on chosen elements content.

(a)

(b)

Figure 2: Dependence courses of residual deformation on change of Fe and Mn content.

4. Discussion

4.1. Influence of Iron and Manganese Contents on Values of Residual Deformation

For increasing values of iron content, it is possible to see the decrease of residual deformation values (Figure 2, Fe (wt.), exp. I). The decrease is also observed at the manganese content increase (Figure 2, Mn (wt.), exp. I). In proposal for iron content in aluminium alloy, the content intervals were suggested, and these intervals were not exceeded during analyses. In one case, the iron content value (0.98%) exceeded recommended range (0.90 to 0.95% Fe); however, no negative effect was observed.

Figure 2 shows diagrams representing whole range of observed iron and manganese contents and residual deformations which depend on those contents. From the diagrams, the decrease in residual deformations in dependence on alloying elements increase is apparent. The recorded decrease for residual deformation was 19.85% for the observed samples. The coupling of the iron content and manganese content can be observed also; this is represented by residual deformation. The test of functional dependences was carried out. At first, the correlations between iron and manganese contents in aluminium alloy and residual deformation were observed independently. In the following, the complex dependences between the parameters were described. For analyzed places A and B, the value of correlation coefficient for measuring of iron content and residual deformation was determined on −0.868, and for manganese content and residual deformation, it was determined on −0.838. The mutual correlation between iron and manganese content was determined on 0.944. Values of correlation coefficients indicate indirect functional dependences between iron content, manganese content, and residual deformation. Values approach significantly the value −1, so the high degree of the correlation can be noted. Multiple coefficient of correlation for analyses in places A and B has value 0.0954. Cummulative characteristic of residual deformation dependence on Mn and Fe content is shown in Figure 3. Differences between measured-out points and theoretical area fall within supposed range, whilst mutual relations of Mn and Fe changes can be observed. The behaviour can be explained from metallurgy point of view by formation of structures on the Al-Fe-Mn-Si basis and their variations, with an assumption that structures with lesser content of alloying elements contain more massive formations of intermetallic phases Al(FeMn)Si and lower content of Mn causes more frequent occurrence of intermetallic ferritic phase Al₃FeSi [11]. This was the reason to carry out analysis to evaluate the samples. Therefore, the metallographic analysis was carried out to evaluate the particular samples in terms of the formation of structures as well as their possible effect on the mechanical properties of the casts.

Figure 3: Dependence of permanent deformation on iron and manganese.

From the analysis of microscopic images, it follows that structures of A1, A2, B1, and B2 samples (Figure 4) contain fine structural zones of intermetallic phases Al(FeMn)Si and defects in the form of bubbles in dimensional range  μm. Structures of A8, A9, B8, and B9 (Figure 4), on the other side, contain more massive structural zones of intermetallic phases Al(FeMn)Si and internal defects in greater dimensional interval  μm. Also the structures of ferritic phase Al₃FeSi and intermetallic phase FeSiAl₅ are observed as more massive needles. In the case of FeSiAl₅, long needles are forming; these can cause defects due to the notch effect. Variations of ferritic phase Al₃FeSi from massive and more frequent in samples A8, A9, B8, and B9 to finer and less frequent in samples A1, A2, B1, and B2 correspond to the increase in Mn content. All images also show particles of undissolved silicium in a form of irregular objects.

Figure 4: Metallographic images of boundary casts.

More massive structural zones of ferritic phase Al₃FeSi have negative effects on values of residual deformation, while they are compensated by increasing manganese content which causes refining of Al₃FeSi phase and formation of intermetallic Al(FeMn)Si phases. These structures are more beneficial in terms of exposure to residual deformation.

In the case of manganese, it is necessary to observe the correlation, because if it is not saturated, and it is eventually deposited as a thermal compound AlMnSi.

5. Conclusions

Realized experiments and discussions show several important aspects of obtained and verified knowledge. Experiments were focused on a group of three elements (Si, Fe, and Mn) occurring in subeutectic Al-Si alloy. Selection of the group was based on knowledge of realized measurements obtained within monitoring of processes in heating furnaces, where variations of elements concentration have been observed. The variations relate to silicium, iron, and manganese, all in decreasing trends.

Described results also show that in casting process, concentration variation of silicium, iron, and manganese may occur, whilst these variations in the conditions of real experiment have reached values for Fe 15%, for Mn 27%, and for Si 7%. Also, an influence of these variations on values of residual deformation was confirmed; theoretical approach was proved. The change of deformation in such a case is 16% from observed interval. At the same time, it is possible to evaluate correlation coupling of Si/Fe/Mn with regard to the metallographic tests results.

From verification measurements and from overall behaviour of particular ingredients, it can be concluded that even though the iron is an impurity, it can be used to increase compression strength for loads in incomplete unload discharge. The mean deformation value of standard meltage presents value 0.313 mm with standard deviation 0.0163 and variance of residual deformation . Repeated tests with increased values of Fe and Mn contents showed decrease in mean deformation value to 0.2905 mm with standard deviation 0.0053 and variance of residual deformation . Results demonstrated decrease in deformation on an average 7.6%. In such a case, it is suitable to apply interval of Fe content up to 0.95% of mass content. However, it is vital to proportionally increase amount of manganese too, in order to refine structures. If the growth of needle-shape structures is significant, there is a chance of local defects in form of slipping planes; that is, why refined structures are sought for.

Taking into account the variations of alloy content comparing to commercial alloys, it is possible to ensure alloying elements content increase during melting process by subsidizing the particular ingredients or by proper combination of recurrent material.

References

M. Sadeghi and J. Mahmoudi, “Experimental and theoretical studies on the effect of die temperature on the quality of the products in high-pressure die-casting process,” Advances in Materials Science and Engineering, vol. 2012, Article ID 434605, 9 pages, 2012.

E. Ragan, Väzkost’ a Počiatočné Napätie v Intervale Kryštalizacie, FVT TU Košice so sidlom v Prešov, Prešov, Slovakia, 1997.

E. Ragan and M. Fedak:, “Kvalita odliatku v závislosti na procese tlakového liatia,” in Proceedings of Technology Systems Operation Conference (TSO ’07), p. 2, FVT TU, Presov, Slovakia, 2007.

J. Malik, P. Futáš, I. Vasková, et al., “Nehomogenita tlakového odliatku z podeutektického silumيnu,” Slévárenství, vol. 55, no. 7, pp. 307–310, 2007.

E. Ragan, Proces Liatia Pod Tlakom, FVT TU Košice so sídlom v Prešove, Prešov, Slovakia, 1997.

E. Ragan and S. Fabian, Liatie Kovov Pod Tlakom, VMV, Prešov, Slovakia, 2007.

P. Dzugas, J. Vilcko, D. Sulik, and J. Mester, “Experimentálne štúdium tuhnutia odliatkov zo zliatin typu Al–Si liatych s tuhnutím pod tlakom-part III,” Slévárenství, no. 1, pp. 7–8, 1992.

E. J. Vinarcik, High Integrity Die Casting Processes, John Wiley and Sons, New York, NY, USA, 2003.

E. Ragan, M. Fedak, and P. Skok, “Zabiehavosť v dutine formy pri technológií liatia pod tlakom,” in Operation and Diagnostics of Machines and Production Systems Operational States: Scientific Papers, pp. 146–153, Tribun EU, Kraków, Poland, 2008.

J. Laudar, Liatie Pod Tlakom, SVTL, Bratislava, Slovakia, 1964.

D. Bolibruchová and E. Tillova, Zlievarenské Zliatiny Al–Si, Žilinská univerzita v Žiline, Žiline, Slovakia, 2005.

T. Grígerová, R. Koreny, and I. Lukac, Zlievárenstvo neželezných kovov, ALFA, Bratislava, Slovakia, 1988.

J. Jurko, M. Džupon, A. Panda, and J. Zajac, “Study influence of plastic deformation a new extra low carbon stainless steels XCr17Ni7MoTiN under the surface finish when drilling,” Advanced Materials Research, vol. 538–541, pp. 1312–1315, 2012.

J. ] Vilcko and S. Slovak, Zlievarenská Technológia, ALFA, Bratislava, Slovakia, 1987.

V. Zabavnik and M. Bursak, Materiál, Tepelné Spracovanie, Kontrola Kvality, Hutnícka Fakulta-TUKE, Košiciach, Slovakia, 2004.

I. Lukac, Vlastnosti a Štruktúra Neželezných Kovov, ALFA, Bratislava, Slovakia, 1987.

J. Valecky, L. Jeníček, V. Oliverius, et al., Lití Kovů pod Tlakem, SNTL, Praha, Czech Republic, 1963.

J. Vilcko and P. Dzugas, “Liatie s tuhnutím pod tlakom zo zliatin typu Al–Si, Úvod do problematiky technológie výroby vysokokvalitných odliatkov (časť I),” Slévárenství, no. 12, pp. 499–504, 1990.

A. Gorny, J. Manickaraj, Z. Cai, and S. Shankar, “Evolution of Fe based intermetallic phases in Al–Si hypoeutectic casting alloys: influence of the Si and Fe concentrations, and solidification rate,” Journal of Alloys and Compounds, vol. 577, pp. 103–124, 2013.

S. Ji, W. Yang, F. Gao, D. Watson, and Z. Fan, “Effect of iron on the microstructure and mechanical property of Al–Mg–Si–Mn and Al–Mg–Si diecast alloys,” Materials Science and Engineering A, vol. 564, pp. 130–139, 2013.

M. Fedak, P. Semanco, and M. Micko, “Statistical process control method based on weight percent of Al–Si alloy for melting and holding process in die casting,” in Lecture Notes of the Institute for Computer Sciences, Social Informatics and Telecommunications Engineering, vol. 62, pp. 188–190, 2012.

M. Fedak and P. Semanco, “Monitoring of chemical composition of aluminium alloys Al–Si in the maintenance furnace,” in Scientific Papers: Operation and Diagnostics of Machines and Production Systems Operational States, vol. 3, pp. 139–144, RAM, Lüdenscheid, Germany, 2010.