Analytical and Numerical Study of the Ground Pressure of the Work Face Crossing the Fault

-e excavation of coal mine often encounters the fault problem. In this paper, the analytical study of the pressure of the fault that the work face may cross is carried out. -e evolution of the stress and moment of the fault is investigated. Afterwards, a numerical study is performed. -e stress and displacement of the rock mass near the work face and the fault are calculated under each situation (the initial fracture and periodical fracture of the immediate roof, the forward direction fault, and the reverse direction fault), and the changes in the contact pressure and stress near the fault during the excavation are analyzed. -e effect of searching tunnel on the mining pressure is also studied. -e calculation results indicate that although the searching-tunnel can decrease the stress at the roof of the fault (reverse direction fault), it may increase the stress at other positions. It can therefore be concluded that, for the forward direction fault, the effect of the searching tunnel to decrease the contact pressure and dissipate the energy is limited; on the contrary, it will aggravate the fragmentation degree and make the support more difficult, while, for the reverse direction fault, the excavation of searching tunnel can not only provide a better understanding of the characters of the fault but also have a positive effect on the ground control.


Introduction
Coal is one of the most important energy sources in the world and one of the main energy sources used by human beings since the eighteenth century and is known as the "real staple food" in industry. China is the largest country in coal consumption in the world, and coal accounts for more than 55% of the total primary energy consumption. Although the proportion of clean energy sources, such as hydropower, wind power, and nuclear power, continues to increase, the dominant position of coal will be difficult to change in a short period of time. e coal-based energy structure supports the rapid development of Chinese economy. In 2021, the total consumption of coal will stabilize at about 41.8 billion tons [1][2][3][4].
Ground pressure which is induced by the mining disturbance is a major safety problem during coal mining. With the continuous improvement of coal mining equipment, technology, and the improvement of safety supervision system, coal mine accidents have been effectively prevented and controlled, and the number of safety accidents has decreased year by year [5,6]. However, the roof disaster can be induced by many causes, and such disaster is easy to burst and difficult to prevent and control. It is still an important factor effecting the coal mine safety production [7][8][9]. e analysis of the characteristics of roof disaster and the study of the law of roof activities are the key to the prevention and control of surrounding rock disasters [10,11]. Ground pressure can be generally classified as the initial pressure and the periodic pressure. e initial pressure is dramatic, and it may cause a step-like subsidence of the roof and serious damage to the supporting. Compared with the initial pressure, the periodic pressure is relatively moderate and the ground pressure may increase periodically [12]. According to the different actual situation of coal seam, the mine pressure produced by it is also different.
At present, many studies have been carried out to exploration the problem of ground pressure. Yan et al. adopted SOS microseismic monitoring system, numerical simulation to study the microseismic law of fullymechanized work face with a fault [13]. Shi et al. analyzed the special mine pressure law and put forward the mechanical model of special coal pillar [14]. Cai et al. proposed a method of characterizing rock mass damage near excavations based on microseismic event monitoring. And a damage numerical model, which takes the microseismic data as input to determine the damage state described by fracture density, was presented. It was found that when damage related softening based on microseismic data was considered, the predicted displacements of the rock mass were in good agreement with extensometer measurements [15]. Suchowerska et al. identified the relative magnitude of horizontal stress change below a series of parallel longwall panels as a consequence of multiseam mining; the key findings of this research are that the maximum horizontal stress would approximately have a 10% of the original in situ horizontal stress for the case of isotropic rock strata [16]. Jiang et al. provided treatment measures, such as design of the position of the longwall panel, rational arrangement of roadways, stress prereleasing, and enhancement of monitoring [17]. Meanwhile, there are many studies about the mining induced deformation and failure behaviors of the rock. Based on the physical model, Lou et al. pointed out that the tensile principal stress is inversely arched before the first breaking, and the breaking line forms an obtuse angle with the advancing direction of the panel during the periodic breaking [18]. With the mining/excavation disturbance background, Hao et al. studied the crack initiation and propagation under the static-dynamic loading conditions, the evolution of the strength, crack properties such as direction and type are studied with the loading rate and the proportion of the static and dynamic loads, and the anisotropy effected are detailed analyzed [19,20]. Zhang et al. proposed a comparison study of the rock fracture network evolution under the three different stress paths of mining disturbance (top-coal caving mining-TCM, nonpillar mining-NM, and protective coal-seam mining-PCM), and they pointed out that the degree of fragmentation/fracture network complexity of the rock increases by PCM, NM, and TCM conditions [21]. In addition, the mining depth is also a key factor for the properties of the rock; the deformation, damage behavior, and the energy transformation and transition mechanism are significantly different for different depth [22].
A fault that exists in front of a work face will affect the ground pressure greatly. It is necessary to investigate the direction of the work face excavation. Based on a coal mine of Yanzhou area, this paper presents a comparative study on the law of ground pressure behavior of the working face of under the forward direction fault and the reverse direction fault. Based on the theory of material mechanics, the mechanical model of the roof is established. e initial breaking distance and maximum tensile stress of the roof for both of the forward direction fault and reverse direction fault are studied. e simulation of the working face crossing through the fault is carried out. e law of ground pressure behavior of working face through the forward direction fault and reverse direction fault is investigated via a numerical method. e influence of the searching tunnel on the pressure behavior of working face passing through fault is analyzed. e relevant models are established to study whether the contact stress at the fault, displacement, and stress of roof are improved if the searching tunnel is excavated. Here, the concept of the searching should be stressed. It is different from exploration roadway [23] which is used to find out the geological conditions.

The Analysis of Mechanics Model of Work
Face Crossing the Fault e mechanical model of the work face with the fault is shown in Figure 1. e left and right ends of the model are fixed, and a uniformly distributed force q is applied immediately on the roof. e overburden pressure is simplified as q. e faults in this paper are different from the normal faults mentioned in coal geology. After the formation of a fault, the hanging wall is relatively down; the floor that is relatively higher than the fault is called normal fault [24]. Currently, an inclined fault occurs on the roof of the coal seam ( Figure 1). When the mining direction and the fault dip angle are less than 90°, the fault is defined as the forward direction fault; when the mining direction and fault dip angle are greater than 90°, the fault is defined as the reverse direction fault. [25,26]. e schematic diagram of the above fault structure is simplified as a cantilever beam model. e left end of the cantilever beam is the fixed end, and the right end is the free end ( Figure 2). e upside of the beam is subjected to the uniform load p 1 , and the underside is subjected to the uniform load p 2 . e action length of p 2 is a, the right end is subjected to the shear force F. e length of the beam is l, the height of the beam section is h, and the breadth of section is b. According to the cantilever beam and simply supported beam model, the stress of the immediate roof in the initial and periodic fracture can be deduced.

Forward Direction Fault
2.1.1. Initial Facture. When 0 ≤ x ≤ l − a, the bending moment at x can be written as  Figure 3 is the variation of bending moment with the assumption that fracture position is in the range of 0 ≤ x ≤ l − a. Figure 4 is the variation of bending stress with the assumption that fracture position is in the range of 0 ≤ x ≤ l − a.
e initial facture distance is calculated as e cantilever beam produces the maximum bending moment at x.
When l − a < x ≤ l, the bend moment M(x) can be written as e evolution of the bending moment and the stress of the beam is shown in Figures 5 and 6. e maximum stress is produced on the cantilever beam during 0 ≤ x ≤ l − a.
erefore, the section in which the cantilever beam is broken is 0 ≤ x ≤ l − a. Figure 5 is the variation of bending moment with the assumption that fracture position is in the range of l − a < x ≤ l . Figure 6 is the variation of bending stress with the assumption that fracture position is in the range of l − a < x ≤ l. Figures 3-6, the maximum value of the moment and the stress are at x � 7.5 m, which is prone to instability and failure.

Periodical Facture.
Periodical facture can be simplified as a simply supported beam mode ( Figure 7). To set the balance distance of rotation as l 1 , the moment equilibrium equation can be written as us, l 1 can be expressed as e periodical facture distance expression can be obtained by replacing l in x expression with l 1 .

Mechanics Analysis of the Fault.
e fault is shown in Figure 8. It is assumed that the upside of the working face is subjected to uniform load P 1 , the underside is subjected to uniform load P 2 with length a, the angle θ between fault plane and vertical direction is narrow, and the vertical direction load is P 3 . When calculating the stress at the fault, it can be regarded as a problem of variable cross section beam.
erefore, the stress in the fault is a constant. In this section, the theory of materials mechanics is employed to present the equations of the stresses and moments.
e basic equations and assumptions can be found in any books or references of material mechanics. Equations (1)-(10) are also listed in the previous work of our group [25,26]. e parameter calculation and the judgement of the position of initial fracture based on the plots of bending moment and bending stress is discussed in this paper.

Reverse Direction
Fault. Similar to the forward direction fault, the reverse direction fault is also simplified to a cantilever beam model. e corresponding loads are applied as in Figure 9.        If l � 50 m, a � 20 m, h � 1 m, P 1 � 2000 N/m, P 2 � 4500 N/m, F � 4000 N, the evolution of the bending moment and the stress of the beam is shown in Figures 10  and 11. Figure 10 is the variation of bending moment with the assumption that fracture position is in the range of 0 ≤ x ≤ l − a. Figure 11 is the variation of bending stress with the assumption that fracture position is in the range of 0 ≤ x ≤ l − a. Both the maximum values of the moment and the stress occur about 20 m to the left end.
Let M � M max ; the initial facture distance can be obtained: When a < x ≤ l, (14) Figure 12 is the variation of bending moment with the assumption that fracture position is in the range of a < x ≤ l. Figure 13 is the variation of bending stress with the assumption that fracture position is in the range ofa < x ≤ l. e evolution of the bending moment and the stress of the beam is shown in Figures 12 and 13. e maximum stress is produced on the cantilever beam during a < x ≤ l. erefore, the fracture position of the cantilever beam should be in the range of a < x ≤ l.
Based on the results of stress and moment shown in Figures 10-13, the maximum values of the moment and the stress are at the position of 50 m to the left end. erefore, such position is prone to instability and failure.
Let M � M max : us, the bending moment at the coal wall is as follows: e tensile stress at the coal wall is obtained as follows:

Periodical Facture.
Similarly, the periodical fracture of the roof can be simplified to a simply supported beam mode ( Figure 14). To assume that, the rotation balance distance is l 1 , and the moment at the support can be written as It can be obtained that

Mechanics Analysis of the Fault.
e fault is shown in Figure 15.
erefore, the stress in the fault is a constant. And the distribution of the stress on the reverse direction fault is the same as that on the forward direction fault. erefore, we may subdivide the problem as initial fracture and the periodical fracture in the numerical analysis.

Establishment of Simulated Mechanics Model.
According to the actual situation, the four models are established. Every model can be modeled with the searching tunnel or without it.
For the situation with the searching tunnel or not, the same model can be used and the elements of the tunnel are "killed" when the tunnel is needed. e exploitation process for every model is simulated; thus the exact exploitation process and a result close to the actual situation can be obtained. Material parameters are shown in Table 1. As shown in Figures 16 and 17, the "support" is used to model the hydraulic support which is used in mined out area. e sketch of the four models is shown in Figures 16-19. e length of model is 150 meters; the angle of fault is 60°. e simulation is carried out by using the FEM software ANSYS. Table 2. According to Figures 20-25, the roof above the mined-out area is the most dangerous area; the stresses and deformations at the site are significant. For the forward direction fault case, the working face is under fault; the stress above mined-out area redistributes continuously with the increase of the mined-out area. For the reverse direction fault case, the fault is far from the mined-out area and the stress is less affected by mined-out area; the stress in reverse direction fault is mainly in situ stress. erefore, the difference of contact pressure between forward direction fault and reverse direction is great. Figures 20(a), 21(a), and 22(a) can also been found in [25] or [26]. Meanwhile, the nephograms of contact pressure in Figures 20-25 are the initial fracture situation. For the periodical fracture situation, the nephograms are not presented in this paper because of space; the related nephograms can be found in [25].

Result and Analysis of Simulated Calculation. e results of simulation are shown in Figures 20-25 and
As shown in Figures 26 and 27, the contact pressure of reverse fault is generally more than that of forward fault. When the initial fracture occurs, the pressure of the   In the case of periodic fracture, the contact pressure of the upside is increasing as the work face is excavated. When the searching tunnel is excavated, the contact pressure of the upside roof does not decrease but increases slightly. erefore, it can be concluded that the contact pressure cannot decrease with the excavation of the searching tunnel.
In the case of the reverse direction fault, the contact pressure of underside roof is increasing as the work face is excavated and it comes to the maximum 28.94 MPa. When the searching tunnel is excavated, the contact pressure is almost the same as before. In the situation of periodical fracture, the distribution of the underside contact pressure is nearly the same as it in the initial fracture, but the maximum is decreasing to 23.975 MPa. When the searching tunnel is excavated, the contact pressure of underside roof is not decreasing obviously but even increasing sometimes.
According to the calculation result as shown in Figure 28, for the initial fracture model of the forward direction fault, to carve a searching tunnel increases the displacement of immediate roof that above the exploitation center by 6.7%, decreasing the maximal contact pressure, about 0.192 MPa less than before, and increasing the maximal stress of the immediate roof, the maximal increment is about 4%.
As it is shown in Figure 29, for the periodical fracture of the forward direction fault, to carve out a searching tunnel increases the displacement of immediate roof by about 11.2%, and decreases the maximal contact pressure, about 0.386 MPa less than before; it does not release the maximal stress of the roof; on the contrary, the maximal stress increases; the maximal increment is nearly 11.6%.
For the forward direction fault, the development of the searching tunnel, whether the initial fracture or the periodical fracture, has an increasing effect on the displacement and stress of the roof and slightly reduces the contact stress at the fault. e influence on the periodical fracture is greater than that of the initial fracture.
For the initial fracture model of reverse direction fault, as it is shown in Figure 30, to carve out a searching tunnel, may result in increasing of the displacement of immediate roof by      2%, it decreases the maximal contact pressure about 0.384 MPa, and it also has the effect to release the maximal stress of the immediate roof nearly 25.9% at most. But to carve out a searching tunnel increases the displacement or stress of the immediate roof in forward direction fault.
As it is shown in Figure 31, for the periodical model of reverse direction fault, to carve out a searching tunnel decreases the displacement of immediate roof by 19.54%, and decrease the maximal contact pressure of fault about 0.662 MPa, it also has the effect of release the maximal stress of the immediate roof, nearly 38% at most.
For the reverse direction fault, in the case of the initial fracture, the development of the searching tunnel has almost no positive effect on the displacement of the roof and plays a role in releasing the stress of the roof. In the case of periodic fracture, the displacement and stress of the roof are greatly reduced by the excavation of the searching tunnel. e contact stress at the fault is slightly reduced when the searching tunnel is excavated. e optimal plan is the forward direction fault without the searching tunnel or the reverse direction fault with the searching tunnel. erefore, in the process of coal seam mining, it is not necessary to excavate the searching tunnel  when the forward direction fault is encountered, and it is suggested to excavate the searching tunnel when the reverse direction fault is encountered. Table 3 summarizes the influence of searching tunnel on the roof and fault plane. e conclusion of the searching tunnel can be obtained as follows: (1) e contact stress at the forward and reverse direction fault is slightly reduced by the development of the searching tunnel. It can therefore be concluded that its effect to decrease the contact pressure and dissipate the energy is limited. (2) For the forward direction fault, the displacement and stress of the roof are increased by the development of the searching tunnel, especially for the periodical fracture case. It will aggravate the fragmentation degree and make the support more difficult. erefore, for the

Conclusion
In this paper, the analytical and numerical study of the work face crossing a fault is carried out. e stress distribution is investigated with the searching tunnel for both the forward direction fault and the reverse direction fault.
(1) Based on the analytical solution, the initial fracture may occur outside the support range, and the contact pressure is constant based on the beam model. e maximum stress of the roof was also not released, which was increased by nearly 11.6% at its maximum. (4) For the initial fracture model of reverse direction fault, to carve out a searching tunnel may lead to increasing of the displacement of roof by 2%, it decreases the maximal contact pressure about 0.384 MPa, and it also has effect to release the maximal stress of the roof, nearly 25.9% at most. But to carve out a searching tunnel may increase the displacement or stress of the roof in most time. (5) For the periodical model of reverse direction fault, to carve out a searching tunnel decreases the displacement of the roof by 19.54% and decreases the maximal contact pressure of fault about 0.662 MPa; it also has the effect of release the maximal stress of the roof, nearly 38% at most. (6) e optimal plan is the forward direction fault without the searching tunnel or the reverse direction fault with the searching tunnel. erefore, in the process of coal seam mining, it is not necessary to excavate the searching tunnel when the forward direction fault is encountered, and it is suggested to excavate the searching tunnel when the reverse direction fault is encountered.   Elastic modulus (Pa) μ: Poisson's ratio (dimensionless).

Data Availability
e data used to support the findings of this study are available from the first author upon request.

Conflicts of Interest
e authors declare that they have no conflicts of interest.