Fabrication of Nanofiber Flexible Pressure Sensor and Application in Human Motion Monitoring

Nowadays, people are increasingly concerned about body mass index and monitoring human movement has become a necessity for most people, and the nanober exible pressure sensor fully meets people’s needs, so the research on a nanober exible pressure sensor is very meaningful.e purpose of this article is to study a sensor with high sensitivity of the nanober material of PVDF thin lms. And this article conducts experiments through the prepared pressure sensor and other sensors, which test the three movements of humans taking o, squatting, and running. is article calculates the correct recognition rate, false-negative rate, and false-positive rate and then compares them.e experimental data show that the correct recognition rate of PVDF thinlm nanomaterials is as high as 90%, and the recognition rate of non-nanomaterial pressure sensors is even less than 80%. Nanomaterial pressure sensors will have more room for development.


Introduction
With the steady increase in the standard of living, the disadvantage of lacking of exercise is that the human body breathes in too much energy on a daily basis, which leads to some diseases, these diseases harm people's bodies without knowing it, so people must pay attention to the health status of the body, and portable health monitoring equipment in this demand has appeared. Because of its sensitivity, it has attracted people's attention and has become a research hotspot. e daily activities of the human body are diverse, so how to identify these movements is the object of many researchers.
In today's society, people are becoming more active as the pace of life accelerates and there is less time to exercise; it is very necessary to monitor the status of the daily exercise of the human body. en, exible pressure sensors that can monitor these movements are very important. It allows people to reasonably arrange their daily activities and improves people's health. However, in recent years, scholars have studied the application of various pressure sensors and only use nano ber materials. erefore, it is very important to study exible pressure sensors of new material nano bers.
is article describes the advantages of PVDF lms and some fabrication methods. However, this article is mainly experimental, using three sensors (including non-nano bers) for experimental comparison, which are then compared with them using the pressure sensor of this experiment. e innovations of the article are as follows: (1) this article studies the preparation of PVDF, a nanomaterial, and compares various fabrication methods. (2) It designs and implements a prototype system of human motion state monitoring. In this article, experimental tests were performed on 12 people using three pressure sensors, and the article then presents a comparative analysis. (3) In this experiment, the sensor of nanomaterials and non-nanomaterials was compared to make the experiment more convincing. a research topic for national and international scientists. Zhuo B presented 3D printing for the fabrication of microstructured moulds. It was used to microstructure an elastic polydimethylsiloxane (PDMS) dielectric layer into a flexible capacitive pressure sensor. However, the production of these sensors is expensive [1]. Cheng et al. [2] presented a flexible capacitive pressure sensor design [2]. Yu et al. [3] demonstrated a pressure-based biosensor. ey used Cap-teReantibody to achieve sandwich immunoreactivity against the cancer target methacrylonitrile in reactive cells [3].
In addition, Choi et al. [4] have enabled the fabrication of highly scalable and low-cost strain sensors for monitoring human motion. e energy dissipation of the wave-shaped structure was shown to be lower than that of the planar structure for a given strain [4]. Ai et al. [5] proposed the production of stretchable strain sensors made of polynanofiber for monitoring human movements by electrospinning, increasing the sensitivity of the flexible pressure sensor [5]. Zhang et al. [6] developed a flexible and portable strain sensor made of stretchable spandex yarn. Based on the excellent performance of the sensor, they demonstrated the potential of sensors for monitoring human movement, but the accuracy and precision were not as good as expected [6].

Fabrication of Nanofiber Flexible Pressure Sensors
3.1. Nanofibers. Nanofibers refer to linear materials with a diameter of nanometers and a length of a certain aspect ratio [7]. Also, fibers that are modified by filling ordinary fibers with nanoparticles are also referred to as nanofibers. As far as we know, the theory uses nanomaterials whose physical and chemical properties will vary in length. is is due to the lack of coordination on the surface of adjacent atoms, and the surface energy increases instability and easily combines with other atoms.

Flexible Pressure
Sensor. e flexible pressure sensor is based on the traditional rigid pressure sensor, which uses a flexible material as a substrate to sense the surface of an object to fit with a flexible surface such as fabric or even skin [8]. Based on these unique advantages, it has gradually shown function for portable electronic applications, intelligent robots, biomedical devices, and the preparation of dexterous manipulators. It makes the research of the flexible pressure sensor attract more and more attention [9,10]. With the advancement of scientific research and the demand for production, flexible pressure sensing devices can not only sense changes in pressure acting on their surface, but also sense the stretching of the device itself. At present, the flexible materials used to fabricate flexible pressure sensors are mainly polymers. People are increasingly aware of the environment and the economy, and concepts such as low cost, environmental friendliness, wearability, and convenience have been continuously proposed. e pressure sensors based on paper, fabric, etc. as flexible substrates attract attention because of their eco-friendliness.
Flexible pressure sensors are mainly divided into four types ( Figure 1) [11]. e following describes these sensing principles in detail.
e capacitance value C of the capacitive pressure sensor is Here, ε 0 is the dielectric constant of the vacuum, ε r is the relative permittivity, D is the effective electrode area, and s is the spacing between the panels. A resistance pressure transmitter converts pressure changes to other changes. Resistance determination is given as Here, ρ indicates resistivity, l indicates the length, and S indicates the cross-sectional area. e basic principle of piezoelectric pressure sensor induction is the piezoelectric effect of electrical materials. e principle of the triboelectric pressure sensor is triboelectric charging. ey are all mainly studied today, nothing more than optimizing the material, and its sensitivity is expressed as Here, S represents the sensitivity,Y 0 indicates the value of the electrical output signal, ΔY represents the variation in electrical signal, and P represents the pressure on the sensor.

Fabrication of the Nanofiber Flexible Pressure Sensor.
In this research, the flexible sensor is prepared on the basis of the nanofiber material of the PVDF film, and the PVDF film should be prepared before fabrication [12]. e film is formed by spin coating and casting, and it is then annealed at a certain temperature [13]. en, heat setting is performed under tension to fix the oriented macromolecular structure; finally, the ideal film can be obtained by cooling and subsequent treatment. By querying the information, the advantages and disadvantages of various PVDF film preparation methods are summarized in Table 1.
After PVDF is fabricated into thin films, flexible pressure sensors can be fabricated. e fabrication of PVDF flexible pressure array sensors adopts the method of micro-nano processing, which is mainly based on photolithography [14]. Photolithography is to preserve the pattern of the mask through photoresist and then remove the remaining pattern by etching, so as to obtain the pattern of the mask on the substrate [15]. Baking is required to complete the glue leveling, and the UV irradiation causes a chemical reaction of the photoresist in the area not protected by the mask. By developing and dissolving the photoresist that has chemically reacted on the surface of the substrate, the unexposed photoresist areas are protected. Wet etching removes the exposed areas that are not protected by photoresist, resulting in a final pattern consistent with the mask. With the improvement of the dimensional accuracy of the lithography process, the wavelength of ultraviolet exposure is also decreasing, and the wavelength has undergone a change process from 436 nanometers, 365 nanometers, and 246 nanometers. It is now 193 nanometers, and the dimensional accuracy that it can achieve so far is 130 nanometers [16]. e choice of photoresist is also divided into positive photoresist and negative photoresist. Negative photoresist is to copy the pattern opposite to the pattern on the mask to the surface of the silicon wafer; positive photoresist is to copy the same pattern as the pattern on the mask to the surface of the silicon wafer. Positive photoresist can save the area that is not protected by the mask, and negative photoresist can protect the unexposed area. e positive photoresist is decomposed under the action of ultraviolet light and can be dissolved by the developer. Under the action of ultraviolet light, the strength of negative photoresist is enhanced so that it is insoluble in organic solvents. In addition, some experimental equipment such as data collectors and microscopes should be prepared.

Human Body Monitoring Process.
In this study, the nanofiber flexible pressure sensor monitors human motion, which is mainly determined based on acceleration. It then follows the research idea of statistical pattern recognition. e general process of human motion monitoring is shown in Figure 2 [17].
is article will not explain too much about data collection, data preprocessing, feature extraction, and selection.
is article mainly supplements the method of classification and recognition, which classifies the objects to be recognized.
ere are many ways to solve the classification problem. is article mainly explains the decision tree method and Naive Bayes, and other methods will not be explained. e decision tree is mainly used for classification and prediction, and it finds classification rules in a set of data without rules. It is a tree structure where each internal node represents a test on an attribute, each branch represents a test output, and each leaf node represents a category. Supposing A represents a set of a training samples, and there are n classes C 1 , ..., C n in total. a i indicates the number of samples in C i , P i stands for the probability of the sample, which is part of the C i , and a/a i is used to estimate the information entropy, which is I a 1 , ..., a n � −   As can be seen from the above formula, it is assumed that attribute S is selected as the test attribute. Sample set A can be divided into m subsets, A 1 , ..., A m , and if a ij indicates the Sample size of the C i class on a subset A j , the information entropy of the subset divided by the test attribute S can be expressed as Here, Here, p ij � a ij /|a j |, and finally, the information gain entropy of S is obtained by the difference between these two formulas.
e Bayesian classification algorithm is a method that uses Bayes' theorem to calculate the probability of a sample. Bayes' theorem is shown in the following formula: It represents the probability that Y belongs to class X i . Because the distribution function p(Y) is the same for different samples Y, the size of p(Y | X i )p(X i ) is calculated. e likelihood function derived from the conditional density probability p(Y | X i ) is Here, y k represents the components of n-dimensional feature vector Y.

Placement of Sensor Locations.
People have different accelerations in different positions of the body after performing an action. e sensor is placed on the chest, and the obtained acceleration data are stable and easy to carry. A triaxial accelerometer is placed at the chest position of the human body. e three axes of the sensor are X, Y, and Z axes, as shown in Figure 3 [18].
On the ground, the gravitational component of the acceleration sensor is always constant; that is, it always points vertically downward on the ground. e vector synthesis is shown in Figure 4 [19].
Among them, When the person moves, the values on the accelerometer's three axes are the sum of the acceleration component and the gravity component that arise when the human body moves along each axis. e component of the gravitational direction does not affect our research; therefore, the component of the vertical direction in this chapter includes the gravitational component and the human body acceleration component.
Let (b x (t), b y (t), b z (t)) denote the three-axis acceleration vector of the sensor at time t. In order to find the vertical component of the acceleration signal in human motion, it is first necessary to calculate the gravitational component when the sensor is stationary. is gravity component and (b x (t), b y (t), b z (t)) are then used to estimate the actual vertical component. In order to determine whether the sensor is in a stationary state, three parameters need to be Formula (10) calculates the maximum values for acceleration. Formula (11) calculates the minimum value for acceleration. In formula (12), a x , a y , a z represent the average value of the three-axis data of the acceleration X, Y, and Z axes in a sliding window, respectively.
As the above three parameters satisfy the following formulas, this article judges that the state of the three-axis acceleration sensor is a static state: Here, ε represents a small threshold given in the experiment, and the unit component of the gravitational acceleration can be calculated by the following formula: After finding unit component D of the gravitational acceleration, we combine the actual acceleration vector in human motion with its dot product. It can find component y in the vertical direction. e calculation formula is as follows: After correcting with the above algorithm, we can calculate the vertical component of the acceleration even if the position of the acceleration cannot be determined at the start time. is article presents a method for detecting human movement that uses mainly the properties of human body acceleration in the vertical direction.
In this article, threshold values for the peaks and troughs of acceleration signal in the vertical orientation of the human body and interval between two adjacent peaks and troughs are used as characteristic values to build a decision tree for three actions: running, jumping, and squatting. e identification process is shown in Figure 5 [20].
After knowing the specific process of the sensor, it is necessary to understand the difference between the different responses of the sensor after each action. First, the vertical component analysis of the sensor is used to distinguish the two actions of "jumping" and "squatting" in place. In Figure 6, schematic diagrams represent the time-dependent changes in the vertical component of acceleration for a jumping motion and a squatting motion. e abscissa axis represents time t (unit is s), and the ordinate axis represents the vertical component of acceleration y (unit is m/s 2 ).
Compared with jumping and squatting, the schematic diagram of running is relatively more obvious, showing a waveform, as shown in Figure 7 [21].
So now the distribution diagrams of the three states are clear, and then, it can start the experiment.

Comprehensive Experiments.
e experimenters consisted of 6 females and 6 males, a total of 12 people, aged 20-24 years, 150 cm-180 cm in height, and 50 kg-75 kg in weight. It places the sensor on the experimenter's chest. Each experimenter did three kinds of actions 10 times, and the interval between actions was more than 30 s. For the running test, each experimenter was required to run more than 8 steps.
According to the experimental plan, we counted all the data of the 12 experimenters and recorded the recognition of the three actions. e experimental data are displayed in Table 2.
is document contains statistics on the rate of correct detection, the rate of false negatives, and the rate of false positives for the three actions. e statistics of the experimental results of the three actions are shown in Table 3.
It can be seen that the recognition rate of the sensor for running is higher than that of the other two actions, and the recognition accuracy rate is 95.83%. However, the recognition rate of take-off and squat is relatively low, and the recognition accuracy of take-off and squat is 95.00% and 94.17%, respectively. From the jumping movements shown in the table, we can see that the number of jumps detected in females was significantly lower than that in males, which is explained by the differences in weight and jump distance between males and females. e number of detections was significantly lower in males than in females, again due to differences in the body structure, while we did not overly restrict the experimenter's movements. Combining Tables 2 and 3, it can be seen that the sensor has a high successful recognition rate for various actions of men and women in this experiment, reaching the expected results of the experiment.
is article only uses the sensor in this experiment, and it is difficult to see the advantages and disadvantages of this sensor. erefore, in this experiment, a flexible pressure sensor of nonnanofiber material and another pressure sensor of other nanofiber material were used to monitor human motion. For convenience, nanomaterial 1 refers to the material of the PVDF Advances in Materials Science and Engineering 5 thin film. Nanomaterial 2 represents the other nanomaterials used. en, for these two sensors, running, jumping, and squatting were reused, and the experimental subjects were still the people who used them before. e results of the experiment are presented in Tables 4 and 5.
In addition, this article also summarizes the false positives and false positives of these two sensors, as displayed in Tables 6 and 7.
It compares nanomaterial 1 with nanomaterial 2 and a non-nanomaterial sensor, respectively. It uses bar graphs for comparison. Figure 8 shows the correct recognition numbers for the three movements of running, jumping, and squatting by the sensors of three materials, as shown in Figure 8.
And the comparison chart of the recognition rate of a specific person, as shown in Figure 9.
From the figure above, it is difficult to see the specific differences between them, and we can only note a general trend, namely, that the detection rate of the flexible pressure sensor made of nanofiber 1 is higher and more stable than that of the other two nanofibers [22,23]. However, it is difficult to see how big the advantage is, and then, more specific bar graphs are needed, as shown in Figures 10 and  11. ese graphs show both the correct rate and the false positive rate. It more clearly shows the advantages and disadvantages of pressure sensors of three materials: e overall analysis of the data shows that the recognition rate of the pressure sensor made of nanofiber material is higher than 80%, while the recognition rate of the pressure sensor made of PVDF sheet material reaches 90% in this experiment. In general, the recognition rate of flexible pressure sensors of nanomaterials is still very high, but the pressure sensors of non-nanofiber materials are not good, and the recognition rate is not 80%. Moreover, the leakage rate and the wrong report rate of the pressure sensor made of PVDF film material are very low, which has little impact on the entire identification system. In general, this experiment is still very successful. e pressure sensor of nanomaterials has a high recognition rate of human motion, which needs further research.

Discussion
In this article, nanofiber materials are used to fabricate flexible pressure sensors. Based on the acceleration sensor, this article detects the human body's take-off, squat, and start. At present, there are not many research methods in the field of nanofiber flexible pressure sensor. is article adds a human motion monitoring model to the existing sensor model. is article combines it with the working principle of a flexible pressure sensor to make a new attempt. is article initially studies the preparation of nanofibrous materials such as PVDF films. It will be applied to the sensor, and the experiments will be performed on three movements of jumping, squatting, and running. is article then uses a pressure sensor of another nanofiber material together with a pressure sensor of a non-nanofibrous material to conduct human motion monitoring experiments to obtain all the data. e analysis of the data shows that the correct recognition rate of the flexible pressure sensor of nanofiber material is higher than that of the non-nanofiber sensor. e pressure sensor that is also a nanofiber material depends on the sensitivity of the nanofiber material [24,25].         Advances in Materials Science and Engineering rough this experiment, it can be known that the flexible pressure sensor of nanofiber material plays a very important role in human motion monitoring. When choosing a sensor, people should not only pay attention to whether the material prepared by the sensor is a nanofiber material, but also pay attention to whether the nanomaterial is good or bad [26]. Only by choosing the right sensor can we better monitor the physical condition and improve the body index.

Conclusion
In this article, the specific method of fabricating flexible pressure sensor from nanofiber material is not described in detail. It mainly studies the monitoring of the human body by the flexible sensor of the nanofiber. In this article, 12 volunteers (6 females, 6 males) were tested for 10 times of jumping, squatting, and starting movements. By observing the recognition of the three actions by the sensor, the correct recognition rate, the false alarm rate, and the false alarm rate are calculated.
is article also uses two other sensors to conduct experiments together with PVDF thin-film pressure sensors. It is found that the recognition rate of the pressure sensor of the PVDF film is as high as 90%. e other two sensors have a lower recognition rate than it, and the pressure sensor recognition rate of nonnanofiber materials is even lower. However, there are some shortcomings in this experiment; that is, the experimenters may take off, squat, and run at random, which affects the reliability of the data. If conditions permit, experimental tests can be conducted on more people. It increases data reliability, and it can also increase action types. But in general, the experiment was successful, and the pressure sensor of nanofiber materials will be more and more studied in the future, and the recognition rate will be higher and higher.

Data Availability
Data sharing is not applicable to this article as no new data were created or analyzed in this study.

Conflicts of Interest
e authors declare that they have no conflicts of interest.