A High Efficiency Li-Ion Battery LDO-Based Charger for Portable Application

This paper presents a high efficiency Li-ion battery LDO-based charger IC which adopted a three-mode control: trickle constant current, fast constant current, and constant voltage modes. The criteria of the proposed Li-ion battery charger, including high accuracy, high efficiency, and low size area, are of high importance. The simulation results provide the trickle current of 116mA, maximum charging current of 448mA, and charging voltage of 4.21 V at the power supply of 4.8–5V, using 0.18 μm CMOS technology.


Introduction
As we know, portable devices have become the main applications of advanced technical products.Due to their small size, light weight, and recharge ability, Li-ion batteries are well suited to portable electronic manufactures such as cell phones and PDAs [1] because of their high energy density, long cycle life, high voltage, and absence of memory effects.But the life of a rechargeable battery depends not only on charging time, but also on overcharging control and charging strategies [2].To avoid the battery from overcharging, the charging process needs a specific method supporting the constant current (CC) and the constant voltage (CV) modes in order to charge the battery by a degrading current [3][4][5].
In literature, there are several architectures of battery chargers with different approaches of power control methods in order to adapt the supply voltage.The same are characterized by high efficiency such as the DC/DC converter, switching-capacitor, or switching mode power supply [1,[6][7][8], but they are not suitable for single chip integration and, sometimes, they have low accuracy despite their efficiency.On the other hand, the same are using charge pump as an adaptive supply voltage [3]; however this one is distinguished by its high current ripple and low efficiency.LDO-based charger is characterized by a low current ripple and it can be integrated into the chip without descript components [9], but its major problem is the low efficiency.In this work we will improve the efficiency of an LDO-based charger, using the power transistor as a variable current source and minimizing its dropout.
One of the important missed criteria in several works [1,3,6,[8][9][10][11][12] is the control of temperature during charging and the lack of trickle current charge mode in [1,13] which is necessary for the battery protection when it is fully discharged.That makes this work a complete battery charger chip with respect to all charge procedures and the battery protection.
This paper describes the architecture and simulation results of a three-mode control high efficiency battery charger integrated circuit for Li-ion batteries with charging currents from 116 mA up to 448 mA.In Section 2 we describe the typical charging method of Li-ion battery.The architecture and the functionality of major blocks of the proposed integrated circuit are illustrated in Section 3. Simulation results are shown in Section 4. Finally, the conclusion is remarked in Section 5.

Li-Ion Battery Charger Method
Amongst the important criteria of Li-ion battery charger is safety of charging.Yet there are some limitations for the V bat < 2.9 V?
V bat < 4.2 V? current and voltage of charging; thus, the battery temperature will augment severely causing fatal troubles due to some of these limitations.Notably, the typical charging current is 1C, in which the current can completely charge a battery in one hour [14].
The typical charging profile of Li-ion batteries shown in Figure 1 is needed to achieve three fundamental modes: trickle constant current, fast constant current, and constant voltage modes.
So far as the first trickle constant current mode is concerned, when the battery voltage ( bat ) is less than 2.9 V, the internal resistance of Li-ion battery is getting larger; the Li-ion battery, accordingly, has to be charged by a trickle constant current phase; this strategy is called an "overnight charger" [15]; as for the second phase, once the value of  bat is larger than 2.9 V, the process switches from the trickle current to the fast constant current phase.
Ultimately, we use constant voltage to charge the battery when the battery voltage is greater than 4.2 V, whilst the charger is operating within constant voltage mode.
There are two methods to terminate the charging process, the first of which is monitoring the minimum charging current at the CV stage.The charger terminates the charging process when the charging current shrinks to the specified range.To finish the charging process, the other one is based on the maximum charging time [16].
In the proposed design, we have adopted the first method to terminate the charging process; the battery is charging until the charging current is less than 1C/40.
The whole charging flow of our Li-ion battery charger is designed as shown in Figure 2.

Circuit Descriptions
Contrary to the other architectures which use a microprocessor to control the different modes of the charge, our proposed architecture is a purely analogic support of the three modes of Li-ion battery charging, trickle constant current, fast constant currant, and constant voltage, as shown in Figure 3.It is made of many blocks: LDO, current generator, current sense, temperature sense (PTAT circuit), and bandgap multioutput.The supplying tension 4.8 V-5 V is adapted by LDO regulator before generating  adapt .The power transistor MP is equivalent to a variable current source; this technique has been used in [10] with flyback converter.The MP control made by two current sources  ref1 and  ref2 passed through a shifter level composed of 1, 2,   1, and   2, so that the transistor MP provides a constant current order of 116 mA and 448 mA to order the trickle constant current and the fast constant current modes.We use the integrator to control the constant voltage mode.These modes are switched by Op  2 and  3 that compares tensions  fb1 and  fb2 with  ref1 .We use the output of  1 and  4 to stop charging when the battery is full or when the temperature detected by the PTAT circuit exceeds 115 degrees.
Figure 4 shows the complete architecture of the proposed Li-ion battery charger.What distinguishes our architecture is the use of current like a parameter of command to switch the power transistor MP between different modes of charge, and it is utilized like a variable current source.The current generator furnishes two reference currents  ref1 and  ref2 which are copied by current mirror (4 and 3) to command the MP gate with level shifter (this current generator will be discussed in Section 3.1).Unlike trickle constant current and fast constant current (CC mode) witch are under the control of  ref1 and  ref2 , CV mode is controlled by an integrator, following its principles [10]; when  fb1 is getting larger gradually, the integrator output is decreasing, so the MP furnishes a current decrease until the end of charge; we could make use of voltage-to-current conversion to generate CV current.
The end of charge occurs when the current sense detects that  chg (charge current) equals 20 mA or when the die temperature transpasses 115 ∘ C switching off PMOS ( eoc ) integrated into the current generator.

Current Generator.
The current generator furnishes the reference currents,  ref1 and  ref2 , to control the trickle CC and fast CC modes.We have opted for utilizing this architecture, as shown in Figure 5, which is not influenced by the temperature variation [17].It is formed by a conventional architecture (6-6-9-10) where the passive resistor is changed with a PMOS transistor 18 and its gate bias generator.There are two diode-connected NMOS transistors and one PMOS transistor that make up the gate bias generator, for each mode (11, 12, and 7 for  ref1 mode and 13, 14, and 8 for  ref2 mode).Whereas 7 copies the reference current , the gate voltage of 18 is generated by the diode-connected transistors 11 and 12 to generate  ref1 .We can generate the reference current  ref1 or  ref2 by the control switches 15 and 16.We integrate a transistor  eoc switcher to cancel the generation of  ref1 and  ref2 to end the charging process. ref3 , and  ref4 ), hence making use of multioutput bandgap reference tensions.Figure 6 shows a high precision temperature compensates CMOS bandgap reference [18].This latter is improved in order to generate  ref1 = 1.3 V,  ref2 = 1.4 V,  ref3 = 0.53 mV, and  ref4 = 0.99 mV reference voltages by means of adding four out-stages.

V comp
The equation of the two generated currents, which are proportional to  EB and Δ EB , to bias these four added stages, is the following equation: As shown in Figure 6, each current is divided into two other currents passing through two branches containing resistor and bipolar transistor in such a way that We made  2 =  3 , to make the voltage of  equal to .The inputs of the operational amplifier are equalized.From Figure 6,   =  EB1 .Consider So, the outputs reference voltages of the proposed multioutput BGR can be obtained as Unlike  EB1 , which has a negative TC, Δ EB has a positive TC.So, all outputs ( ref1 ,  ref2 ,  ref3 , and  ref4 ) become almost autonomous from temperature.Figure 7 shows the simulation of these aforementioned output reference voltages as a function of temperature over the range −40 ∘ C to 120 ∘ C.

Current Sense.
To sense the current on power transistor MP we have used the  cs transistor in the current sense circuit shown in Figure 8 to make the voltage of  sd of  cs V (V) V (mV)  and MP equal.We have used the OP.The current of  cs MP can be described as the following equation: =  chg . ( chg and  sens are proportional to their aspect ratios.Their ratio can be described as Figure 9 shows the simulation results of sensing currents.

Simulation Results
The results simulation waveforms of the proposed Li-ion battery charger are presented in Figure 10.The reference currents are, respectively, 116 mA and 448 mA for working at the trickle constant current and fast constant current modes.The range voltages are presented as 2.5 V and 4.2 V, correspondingly.The stop current is 20 mA that is equal to around 1C/40 that we have defined.The transition between CC and CV mode occurs, as shown in Figure 11.And as can be observed in Figure 12, the system is stable.
Figure 13 shows a layout of the battery charger integrated circuit.As expected, the Li-ion battery charger was designed using 0.18 m technology; most of the area is occupied by the power PMOS pass device, in which the effective die area is 1.172 mm 2 .Table 1 summarizes the performance characteristics of the proposed battery charger IC herein presented.Apparently, this work presents an average power efficiency up to 87% and better performance in terms of maximum current charge and very small chip size.

Conclusion
The presented Li-ion battery charger has been designed with 0.18 m CMOS processes.The proposed charger is operating

Figure 1 :
Figure 1: Typical charging process of a Li-ion battery.

Figure 3 :
Figure 3: Simplified diagram of the proposed Li-ion battery charger.
Multioutput.In our proposed design, four reference tensions would be prerequisite ( ref1 ,  ref2 ,

Figure 4 :
Figure 4: Complete architecture of the proposed Li-ion battery charger.

Figure 9 :Figure 10 :
Figure 9: Simulation results of sensing currents; from top to bottom, the waveforms are the charging current  chg and the sensed current  sens , respectively.

Figure 11 :Figure 12 :
Figure 11: Transition from CC to CV mode.

Table 1 :
Summary of simulation results.