Computational Intelligence and Neuroscience
Volume 2015 (2015), Article ID 750304, 9 pages
http://dx.doi.org/10.1155/2015/750304

Research Article

Study on the Calculation Models of Bus Delay at Bays Using Queueing Theory and Markov Chain

Feng Sun,¹ Li Sun,¹ Shao-wei Sun,¹ and Dian-hai Wang²

¹College of Transportation, Shandong University of Technology, Zibo 255049, China
²College of Civil Engineering and Architecture, Zhejiang University, Hangzhou 310058, China

Received 9 October 2014; Accepted 18 December 2014

Academic Editor: Yongjun Shen

Copyright © 2015 Feng Sun et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

Traffic congestion at bus bays has decreased the service efficiency of public transit seriously in China, so it is crucial to systematically study its theory and methods. However, the existing studies lack theoretical model on computing efficiency. Therefore, the calculation models of bus delay at bays are studied. Firstly, the process that buses are delayed at bays is analyzed, and it was found that the delay can be divided into entering delay and exiting delay. Secondly, the queueing models of bus bays are formed, and the equilibrium distribution functions are proposed by applying the embedded Markov chain to the traditional model of queuing theory in the steady state; then the calculation models of entering delay are derived at bays. Thirdly, the exiting delay is studied by using the queueing theory and the gap acceptance theory. Finally, the proposed models are validated using field-measured data, and then the influencing factors are discussed. With these models the delay is easily assessed knowing the characteristics of the dwell time distribution and traffic volume at the curb lane in different locations and different periods. It can provide basis for the efficiency evaluation of bus bays.

1. Introduction

In recent years, with the rapid development of public transport, bus bays face an increasing pressure especially during peak hours. While serving passengers at a bus stop, buses can interact in ways that limit their discharge flows. This can increase bus delay at bays and degrade the bus system’s overall service quality [1–3]. So it is necessary to evaluate the operating efficiency of bus bays and analyze the reasons for the increase of bus delay and then put forward the countermeasures to reduce the delay.

Though professional handbooks [4, 5] have long offered formulas and tables for estimating bus-stop discharge flow, these are known to be unreliable [3, 6]. The existing studies are mainly empirical formula based on the statistical analysis of actual survey data [7–10] and lack of theoretical model on computing efficiency. Therefore this paper studied the calculation models of bus delay at bays based on the analysis of the bus operating characteristics.

2. Analysis of Bus Delay at Bays

The form of bus bay is shown in Figure 1.

Figure 1: The behavior of queueing for serving at bus bays.

The berths are numbered 1 and 2 from the front to the back, and three buses arriving at the bus bay are numbered 1, 2, and 3 according to the arrival sequence. When buses 1 and 2 occupied berths 1 and 2 to serve their passengers, bus 3 must queue for entering upstream of the stop, as shown in Figure 1. The waiting time during this process is called entering delay.

In addition, when the serving is over at bus bays, the driver must look for a safe opportunity or “gap” in the traffic flow of curb lane to join them, as shown in Figure 2. The waiting time during this process is called exiting delay.

Figure 2: The behavior of waiting for a gap at bus bays.

Therefore, the bus delays at bays mainly including entering delay and exiting delay are computed by the following equation:

where is the entering delay, s; is the exiting delay, s.

We next derived the calculation models of bus entering delay and then studied the computing models of bus exiting delay. The calculation models of bus delay at single-berth and two-berth bays are proposed, respectively, finally.

3. Calculation Models of Bus Entering Delay

3.1. Queueing Model of Bus Bays

At the bus bays serving some lines, buses enter the berth sequentially, then load and unload passengers, and finally exit the stop. So the buses and the stop constitute a queuing system [11]. According to the present study, buses arrived at the stop as a Poisson process, as may occur when a moderately busy stop serves multiple bus routes [12, 13]. So a stop with a general service time distribution and berths can be denoted as the queueing system. In this system, we define a regenerative point as the instant in time when the buses in all berths have discharged from the stop [14]. (Though the stop is empty at each regenerative point, it may be filled immediately thereafter if a bus queue is present at the entrance.) The time interval between two successive regenerative points is defined as a cycle. Let be the number of buses queued at the stop’s entrance at the beginning of the th cycle (i.e., the th regenerative point); is the rate of Poisson bus arrivals; and recall that is the stop’s number of serial berths. So we claim that the stochastic process is a Markov chain in given , , and the distribution of bus service times at the stop. A Markov chain is a sequence of random variables with the Markov property, namely, that, given the present state, the future and past states are independent. In this system, the average bus delay in queue can be calculated once the Markov chain limiting probabilities are identified.

Based on observations of bus operations in China, three assumptions are adopted in the course of formula derivation as follows.

(1)It is assumed that bus overtaking maneuvers are prohibited, both within an entry queue and within the stop itself. Overtaking restrictions of this kind are common in cities, because an overtaking bus can disrupt car traffic in adjacent travel lanes.(2)The bus operating at bays is isolated from the effects of traffic signals.(3)The bus stop system operates in a stable state; the load rate .

3.2. Single-Berth Stop

In this section, we firstly analyze and compute the transition probabilities of bus stop system; the balance equations are then formulated and solved for the Markov chain limiting probabilities; and, lastly, the models which are used to calculate the average bus entering delay are proposed.

3.2.1. Transition Probabilities

Firstly, we define the Markov chain transition probabilities:

Let be the number of buses that arrived in the th cycle, so there is an equation at single-berth bus stop:

Let , ; then

Let be the matrix of transition probabilities; then can be written as follows:

3.2.2. Balance Equation of Limiting Probabilities

According to (5), the state transition diagram of single-berth bays can be drawn, as shown in Figure 3.

Figure 3: State transition diagram of single-berth bays.

Let be the serving time of the th bus; then is a sequence of independent and identically distributed random variables, so we obtain the following equations:

In (6), represents the probability that the number of bus arrivals during is . Buses arrived at the stop as a Poisson process, so the equation is

Equation (7) was substituted in (6); we have

So the expectation of is computed as follows:

The variance of is computed as follows:

Let be the limiting probability that the Markov chain is in state ; that is, . So represents the limiting distribution of the Markov chain. Thus, is the solution to the balance equation:

The equations are established according to the characteristics of the generating function, and then the balance equation of single-berth stop is resolved, as follows:

3.2.3. Average Bus Entering Delay

At the single-berth bus stop, is the number of bus arrivals at the stop during the waiting time and service time of the ()th bus. Let and be the cumulative distribution functions (CDF) of and whichare mutually independent. So the average number of buses in the system can be calculated by the following formula:

and ; (13) was substituted in it; we have

Combine (13) and (14) to solve the average bus entering delay at single-berth bays:

3.3. Two-Berth Bus Stop

The bus entering delay of two-berth bus bays is studied using the same approach as in Section 3.2.

3.3.1. Transition Probabilities

Let be the number of buses that get served in the th cycle. Thus, for represent the probability that the numbers of buses queueing at the stop’s entrance at the beginning of the th and ()th cycles are and , respectively, and the number of buses served at the th cycle is .

For an queueing system, there are six kinds of state transition occurring [14]. We obtain the transition probabilities by finding all the :

Then we determine the expression of each probability in (16) as follows.

(1) : this probability is equivalent to the probability that there is no bus arriving when the first bus finishes its service; thus

where is the headway following the first bus arrival in the cycle, s; is the first bus’s service time in the cycle, s.

(2) : through the analysis, there would be at least 2 arrivals in the cycle; that is, . Let be the time between the 2nd arrival and its departure. Because the service time of buses is different, there are two possible scenarios at two-berth bus bays: the first bus finishes its service before the 2nd bus; the 2nd bus finishes its service before the first bus; thus

where is the second bus’s service time in the cycle, s.

We can derive the CDF of as

Thus, for , the probability is computed as follows:

(3) : according to [6], the CDF of the platoon service time of two buses entering the stop simultaneously is ; then for and

In summary, the mathematical expectation of transition probabilities of two-berth bus bays is given by

3.3.2. Balance Equation of Limiting Probabilities

The solution method of balance equation uses the -transform of to consolidate the infinite-size balance equation into a single functional equation. Then its solution can be converted back to the original distribution:

From the transition probabilities above, the balance equation of limiting probabilities can be written as

Then, we have

The -transform method is used for this. We can write the balance equation in the -domain as

Let ; then we have

Let ; (28) can be converted to

Hence,

3.3.3. Average Bus Entering Delay

Determining the average bus delay in queue requires the calculation of the average number of buses in queue over time. The average number of buses in queue is equal to the average of the queue length seen by each Poisson bus arrival. So it can be calculated by the next equation:

where is the average number of buses in queue, buses; is the average of the queue length seen by the th bus arrival during , m; is the number of bus arrivals during , buses; is the number of cycles during ; is the number of bus arrivals during cycle , buses; is the sum of the queue lengths seen by each bus arrival during cycle , m; is the average of the sum of the queue lengths seen by each bus arrival during cycle , m; is the average of the number of bus arrivals during each cycle, buses.

To obtain and , we consider the following four scenarios which describe the possible states of the system at the start and end of each th cycle.

(1)No bus queues are present at the stop’s entry, both at the start and at the end of the th cycle; that is, . In this scenario, no bus arriving during cycle encounters a queue, and the number of buses that arrive during cycle is the number served during that cycle. So and can be denoted as

(2)A bus queue is present at the start of cycle , but not at the end of that cycle; that is, , and , and . Then and can be denoted as

(3)A bus queue is present both at the start and at the end of cycle , and the number of buses in queue is less than or equal to the number of berths; that is, , and . In this scenario, the stop is filled during the cycle; that is, , and . The first () arrivals fill unused berths, such that the first () arrivals see no entry queue. The following arrivals will see successively longer queues that range from 1 to (). Thus,

(4)A queue size greater than 2 is present at the start of cycle, and a queue thus persists at the end of that cycle; that is, , and . In this scenario, as in the previous one, , and . And since the earliest bus of cycle is characterized by () buses that remain in the entry queue, arrivals thereafter will see queue lengths in the sequence . Thus

Note from the above that the and only depend on , , and . Thus, and can be obtained by taking weighted averages:

where are the long-run probability of a cycle where , , and are calculated by the next equation:

So,

Let ; (38) is converted to

Therefore, we have

From Little’s formula [15], the average bus delay in the queue is then obtained:

The operability of (41) is not strong in practice because it is too complicated. And therefore, it needs to be simplified. The approximate calculation model of bus entering delay of two-berth bays is obtained using the approximation theory of stochastic service system, as follows:

where is the coefficient of variation in bus service time, which is computed by the next equation:

4. Calculation Models of Bus Exiting Delay

According to the queueing theory and the gap acceptance theory, the average exiting delay is equal to the average number multiplied by the average length of nongaps that bus waits for, as shown in (51). Oliver defined any time interval that is greater than the critical headway as a gap and remaining intervals as nongaps [16]:

where is the average number of nongaps that bus waits for; is the average length of nongaps.

(1) Average Number of Nongaps That Bus Waits for. When headways are assumed to have a negative exponential distribution, the probability that bus will join without delay is

where is the flow at curb lane, pcu/h; is the critical gap, s.

The probability that bus will be delayed is

The number of blocks is

The average number of vehicles between the starts of gaps is

Therefore, the average number of nongaps that bus waits for is

(2) Average Length of Nongaps. The total time spent in the nongaps is

The total number of nongaps is

The average length of nongaps is

From this, it is noted that the average exiting delay is found by multiplying the average number by the average length of nongaps that bus waits for; that is,

5. Calculated Results

5.1. Single-Berth Bay

Based on the above analysis, the average bus delay at single-berth bays is calculated by (54):

The average bus delay is calculated with (54) under different demands at single-berth bays, as shown in Figure 4. It can be seen that the bus delay grows slowly when bus flow is less than 60 buses/h and has a rapid growth once bus flow exceeds 60 buses/h.

Figure 4: The average bus delay at single-berth bays.

5.2. Two-Berth Bay

The average bus delay at two-berth bays is calculated by

The average bus delays are calculated with (55) under different demand at two-berth bays, as shown in Figure 5. It can be seen that the bus delay grows slowly when bus flow is less than 100 buses/h and has a rapid growth once bus flow exceeds 100 buses/h.

Figure 5: The average bus delay at two-berth bays.

6. Model Validation

The proposed model is validated using measured data at two bus bays of Tianmushan Road in Hangzhou city. The arriving time, queueing length, and service time of buses at Jingzhou North Intersection and Gudun Intersection bays during peak hours are surveyed by video. Then the delay of every bus is obtained by processing these data, as shown in Table 1. It can be seen that the average relative error between the calculated and the measured values of the bus delay is 10.44%. It shows that the proposed model can effectively reflect the operating characteristics of bus bays.

Table 1: Comparison of the calculated and measured values of bus delay at bays.

Bus bay
Number of berths
Distribution of dwell time (, )
Bus flow (buses/h)
Car flow at curb lane (veh/h)
Calculated values (s)
Measured values (s)
Relative error (%)

Jingzhou North Intersection
2
(2.856, 0.325)
96
360
5.68
5.12
9.86

Gudun Intersection
2
(2.931, 0.414)
120
420
10.52
11.68
11.03

Average
—
—
—
—
—
—
10.44

7. Influencing Factors Analysis

The calculated results above show that the bus delay depends mainly on the average service time at given bus bays. The longer the average service time, the smaller the capacity of stop, which means the bus delay will increase. In addition, it is also affected by the coefficient of variation in bus service time at multiberth bus bays, and the impact characteristics are shown in Figure 6. Visual inspection of this figure reveals that the value of bus delay grows larger with growing in the same bus flow. This is mainly due to the increasing impact between the servicing buses. Therefore, too many bus lines should not be set on the same stretch of road. Because more bus lines will surely increase the coefficient of variation in bus service time, the interaction between buses will be intensified. According to previous experience, 4 or 5 bus lines at most are set up on the major roads in the city [4, 5].

Figure 6: Impact of coefficient of variation in bus service time on bus delay.

8. Conclusion

Formulas were developed to predict the average bus delay at bays. The formulas use a Markov chain that is embedded in the bus queueing process, the queueing theory, and the gap acceptance theory at these bays. Exact solutions were derived for two special cases: single-berth and two-berth bays. And approximations matched up to the surveyed results. With this methodology, the bus delays at bays are obtained easily if the characteristics of the service time distribution and traffic flow are known. And the results of this paper can provide basis for the efficiency evaluation of bus bays.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

This work is supported by the National Natural Science Foundation of China (no. 51278454) and the Shandong Province Natural Science Foundation (no. ZR2014EL036).

References

R. Fernández, “Modelling public transport stops by microscopic simulation,” Transportation Research Part C: Emerging Technologies, vol. 18, no. 6, pp. 856–868, 2010.

R. Fernandez and R. Planzer, “On the capacity of bus transit systems,” Transport Reviews, vol. 22, no. 3, pp. 267–293, 2002.

C. Leiva, J. C. Muñoz, R. Giesen, and H. Larrain, “Design of limited-stop services for an urban bus corridor with capacity constraints,” Transportation Research Part B: Methodological, vol. 44, no. 10, pp. 1186–1201, 2010.

Transportation Research Board, Highway Capacity Manual, National Research Council, Washington, DC, USA, 2000.

Transportation Research Board, TCRP Report 100: Transit Capacity and Quality of Service Manual, National Research Council, Washington, DC, USA, 2nd edition, 2003.

M. Estrada, J. F. Ortigosa, and F. Robusté, “Tandem bus stop capacity,” TRB 90th Annual Meeting Compendium of Papers 1747, Transportation Research Board of the National Academies, Washington DC, USA, 2011.

J. C. Levine and G.-W. Torng, “Dwell-time effects of low-floor bus design,” Journal of Transportation Engineering, vol. 120, no. 6, pp. 914–929, 1994.

R. Rajbhandari, S. I. Chien, and J. R. Daniel, “Estimation of bus dwell times with automatic passenger counter information,” Transportation Research Record, no. 1841, pp. 120–127, 2003.

S. Jaiswal, J. Bunker, and L. Ferreira, “Influence of platform walking on brt station bus dwell time estimation: australian analysis,” Journal of Transportation Engineering, vol. 136, no. 12, pp. 1173–1179, 2010.

L. Y. Yao, L. S. Sun, W. H. Wang, and H. Xiong, “Adaptability analysis of service facilities in transfer subway stations,” Mathematical Problems in Engineering, vol. 2012, Article ID 701852, 12 pages, 2012.

W. Gu, M. J. Cassidy, V. V. Gayah, and Y. Ouyang, “Mitigating negative impacts of near-side bus stops on cars,” Transportation Research Part B: Methodological, vol. 47, pp. 42–56, 2013.

H. Ge, Traffic impacts of bus stops in urban area and related optimization techniques [Ph.D. thesis], Southeast University, Nanjing, China, 2006.

S. Feng, Z. Wen-Tao, Y. Ying, and W. Dian-Hai, “Optimal skip-stop schedule under mixed traffic conditions for minimizing travel time of passengers,” Discrete Dynamics in Nature and Society, vol. 2013, Article ID 930562, 8 pages, 2013.

W. Gu, Y. Li, M. J. Cassidy, and J. B. Griswold, “On the capacity of isolated, curbside bus stops,” Transportation Research Part B: Methodological, vol. 45, no. 4, pp. 714–723, 2011.

D. Gross, J. F. Shortle, J. M. Thompson, and C. M. Harris, Fundamentals of Queueing Theory, Wiley Series in Probability and Statistics, John Wiley & Sons, Hoboken, NJ, USA, 4th edition, 2008.

N. H. Gartner, J. M. Messer, and A. K. Rathi, Monograph on Traffic Flow Theory, The Federal Highway Administration (FHWA), 1996.