International Journal of Aerospace Engineering
Volume 2019 (2019), Article ID 1802659, 11 pages
https://doi.org/10.1155/2019/1802659

Research Article

Reliable Distributed Integrated Navigation Based on CI during Mars Entry

Tai-shan Lou, Nan-hua Chen, Xiao-qian Wang, Zhen-dong He, and Jie Liu

School of Electric and Information Engineering, Zhengzhou University of Light Industry, Zhengzhou 45002, China

Correspondence should be addressed to Tai-shan Lou; tayzan@sina.com

Received 2 October 2018; Revised 24 February 2019; Accepted 10 March 2019; Published 2 May 2019

Academic Editor: Franco Bernelli-Zazzera

Copyright © 2019 Tai-shan Lou et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

A reliable distributed covariance intersection (CI) fusion integrated navigation algorithm with information feedback during the Mars atmospheric entry is proposed to meet robust, reliable, and high-precision Mars atmospheric entry navigation strategy. A distributed integrated navigation scheme includes four independent subsystems consisting of an IMU and one radio beacon, but each subsystem is weakly observable under limited Mars entry measurements. The scalar weights are fast obtained by maximizing the information contribution of the corresponding estimate. The distributed framework based upon the CI fusion algorithm is designed by using dynamic information distribution coefficients and information feedback strategy. This distributed fusion approach could meet the lower computation cost and robust and reliable capacity and especially is beneficial to the weakly observable or unobservable subsystems during the Mars entry navigation scheme. Numerical simulations show that the proposed distributed CI fusion integrated navigation algorithm can provide consistent navigation accuracy for the Mars entry vehicle and improve the entry navigation robustness under the weakly observable navigation subsystems.

1. Introduction

Future Mars exploration missions require the capability of safely pinpoint landing on a high scientific site to verify some science imaginations or carry out scientific experiments. The Mars entry phase is an important and dangerous period during the Mars entry, descent, and landing (EDL) phases, and its navigation accuracy and reliability play a vital role in the Mars landing mission. Robust, reliable, and high-precision Mars atmospheric entry navigation technology during Mars entry is one of the key EDL autonomous navigation technologies [1, 2].

However, many sensors are encapsulated into the heat shield and plasma sheath to insulate high heat, and only the inertial measurement unit (IMU) is usable during the Mars entry phase. To meet the requirements of the higher navigation accuracy, the Mars networks based the radio communication between the Mars entry vehicle and an orbiting radio satellite, or a preset fixed surface radio beacon is proposed [3, 4]. Subsequently, many new Mars navigation scenarios based on new navigation filtering technologies are proposed to solve some key navigation problems, which include the observability [5–7], uncertain parameters [8–11], and biases [12]. For the above navigation scenarios, the designed navigation frameworks are all centralized, and the measurement information is assumed to send the centralized filtering at the same time to estimate the states. The above centralized navigation schemes all obtained satisfying navigation accuracy to meet the requirements of the Mars entry navigation, but the reliability of the navigation strategies is neglected when the communication between the entry vehicle and the Mars navigation networks breaks off or for other reasons.

Compared to the centralized navigation framework, the two advantages of the distributed navigation framework could provide reliable and flexible estimations of the system [13]. The key idea of the distributed filtering is that all the measurement information is processed in parallel at each node to estimate the states, and then, these estimates are sent to a fusion node to fuse them as an overall estimate. As an important concept in the data fusion field, the distributed filtering has been widely applied in many multisensor data fusion systems [14–16].

For the Mars entry navigation system, there are only finite sensors to provide the navigation information. The on-board IMU could always provide three components of acceleration and three components of the angular rate with random biases. Considering the finite range measurement information coming from finite radio beacons, each subsystem of the distributed navigation scenario is designed including the IMU and only one radio beacon. This design of the subsystem brings another problem; that is, each subsystem is weakly observable. The weakly observability of each Mars entry navigation subsystem may bring unforeseeable navigation errors when the state estimates are fused in the fusion node [5].

This paper presented a reliable distributed covariance intersection (CI) fusion integrated navigation algorithm with information feedback during the Mars atmospheric entry phase to meet the requirement for the future Mars exploration missions. Four navigation subsystems are designed to independently estimate the Mars entry vehicle state, and then, these estimations are sent to the master filtering and fused by using the CI algorithm with information feedback to provide consistent estimate results for the Mars entry navigation scheme. In addition, a new fast-distributed scalar weight selection scheme is designed to obtain the scalar weight by using the infinite norm of the matrix.

The paper is organized as follows. Section 2 introduces the Mars entry dynamical system and analyzes observability of the distributed subsystems for the Mars entry. Section 3 presents the reliable distributed CI fusion algorithm with information feedback based on the extended Kalman filter (EKF) and CI fusion algorithm. Section 4 discusses the results from numerical simulations. The conclusions are summarized in Section 5.

2. Mars Entry Navigation Dynamical System

2.1. Dynamical Model

For the sake of simplicity, the entry vehicle is assumed to fly in a stationary and quiet atmosphere of a nonrotating planet. The entry dynamics equations of the Mars entry vehicle in the Mars-centered Mars-fixed coordinate system are given as [3, 17]

where the altitude is the distance from the mass center of the entry vehicle to the center of the Mars; is the radial velocity of the entry vehicle; is the flight path angle (FPA); is the longitude; and is the latitude. The azimuth angle is defined as a clockwise rotation angle starting at due north, and is the bank angle, which is zero in this work. The gravitational acceleration is , and is the gravitational constant of the Mars. and are, respectively, the aerodynamic drag and lift accelerations given by

where and are the vehicle lift and drag coefficients, respectively; is the lift-to-drag ratio; represents the vehicle reference surface area; is the mass of the vehicle: is the dynamic pressure; and is called the ballistic coefficient. is the Mars atmospheric density, and here, an exponential Mars atmospheric density model is assumed as follows:

where is the density on the surface of the Mars, km is the reference radial position (40 km above the Mars surface), and is the constant scale height ( km).

2.2. Measurement Model

2.2.1. IMU Measurement

The accelerometers of the IMU provide the specific force components along three orthogonal axes, and three components of acceleration are given by

where is the accelerometer output along body axes, is the true linear acceleration, is the random acceleration bias, and is the zero-mean Gaussian white noise.

Here, the true accelerometer measurement model is defined by

2.2.2. Two-Way Range Measurement

The two-way range radio measurement provides the distance between the entry vehicle and the radio beacon [18]. The two-way range measurement is defined by

where is the true two-way range measurements; is the vehicle’s position vector; is the position vector of th radio beacon; and is the th measurement noise, which is distributed to the zero-mean Gaussian distribution.

2.3. Framework of Distributed Integrated Navigation

In the Mars entry integrated navigation scheme, there are orbiting radio satellites and two surface radio beacons within sight to provide the two-way range measurements by the radio communication. That is to say, the measurement information comes from the IMU and four radio beacons in the Mars trajectory or on the Mars surface. The integrated navigation scenario of IMU/radio measurement based on the Mars network is in Figure 1.

Figure 1: Integrated navigation scenario of IMU/radio measurement based on the Mars network.

2.3.1. Dynamic Equation

During the Mars entry phase, is defined as the state variables of the entry vehicle, in which the Mars atmospheric density and the lift-to-drag ratio are augmented. The dynamic model in equation (1) is rewritten with the noise term as follows:

2.3.2. Centralized Navigation Scheme

For the centralized navigation scheme, the measurement information from the IMU and the radio beacons are sent to a single filter to estimate the states. So, the measurement equation for the centralized navigation scheme is defined as [3, 8, 10]

2.3.3. Distributed Navigation Scheme

For the distributed navigation scheme, the measurement information is processed in parallel at each node to obtain multiple estimates, and then, these estimates are sent to a fusion node to fuse them as an overall estimate.

In this work, the IMU is set as the public reference sensor system, and the four radio beacons are separated into four observation subsystems. That is to say, there are four subsystems in this simulation, which are defined as

2.4. Observability Analysis for the Navigation Scheme

Observability is always used to evaluate the performance of the navigation capability and could be observed from measurement information. When the navigation scheme has poor observability degree, the state estimations of the navigation system might be divergent or even unstable [3, 6, 19, 20].

Consider a nonlinear dynamic model:

where is the process state vector and is the measurement vector; and are the nonlinear functions.

The locally weakly observability is analyzed by the Lie algebra for the nonlinear navigation systems , whose observability matrix is given by

where the th-order Lie derivative is given by

and the differential of is defined as

For the navigation system at state , the local observability means the rank of in equation (11) is equal to , which is the dimensional of the state [21].

To represent the observability of the nonlinear system, the observability degree is given by

where and are the maximum and minimum singular numbers of the observability matrix . So, it can be seen that . means , and the above system is locally unobservable; means , and the above system is locally weakly observable.

For the above two navigation schemes, Lie algebra and the singular value decomposition (SVD) method (the details of the SVD are in reference [6]) are associated with analyzing the observability degree of the navigation system.

Figure 2 shows the observability degree of the centralized navigation system with EKF, in which the Mars atmospheric density and the lift-to-drag ratio are augmented into the states. The maximum and minimum observability degrees of the centralized navigation system are 10⁻⁸ and 10⁻⁷ in Figure 2, but for the distributed subsystems, their observability degrees are between 10⁻¹⁶ and 10⁻¹³ in Figure 3, and each subsystem becomes weakly observable. The weakly observable navigation system may bring unforeseeable navigation errors during Mars entry [22]. To avoid this problem, a new CI fusion algorithm is proposed to deal with this weakly observable navigation scenario.

Figure 2: Observability degree of the centralized navigation system.

Figure 3: Observability degree of the navigation system.

3. Design of the Distributed Navigation Fusion Algorithm

3.1. System Description

Consider the discrete nonlinear dynamic and measurement models defined as

where is the state vector and is the measurement vector. and are the nonlinear process and nonlinear measurement vector-valued function, respectively. and are independent zero-mean Gaussian white noises, and their covariance are positive semidefinite and positive definite , respectively. They satisfy

where is the Kronecker delta function.

3.2. Extended Kalman Filter

In this work, the classical EKF algorithm is used as the navigation filtering algorithm in the simulation. Here, the classical EKF algorithm is given by three steps as follows:

Firstly, initialize the state and covariance as and , respectively.

Secondly, time update equations are

Thirdly, measurement update equations are

where the symbol “–” denotes a priori estimate and superscript “+” denotes a posteriori estimate. and are the coefficient matrices. and are, respectively, the a priori error covariance propagation matrix and the a posteriori state estimate error covariance matrix at time-step .

3.3. Covariance Intersection Fusion Algorithm

Covariance intersection (CI) provides consistent state estimates by combining the estimations and covariance matrices. The estimate accuracy generally is not better than that of the centralized estimates when the cross-covariance is known exactly, because the centralized filter incorporates the cross-covariance, and the CI method only uses the a posterior information to fuse. But, when the cross-covariance is unknown, the CI method still provides a consistent estimate [13]. Compared with the centralized filtering system, the CI fusion algorithm as a distributed filtering can degrade the computation cost and has better fault tolerance.

Consider three estimate covariance pairs, , , , and . A consistent estimate with four scalar weights is obtained by

where and .

Generally, the scalar weights can be obtained by minimizing the trace or determinant of the covariance matrix . Many approaches are proposed to solve the above optimization problem [23–26]. To fastly obtain the suitable scalar weights for real-time applications, some fast solution has been proposed [26, 27]. Franken and Hupper have used the information matrix of the estimation error variance matrix as considering estimation certainty [27]. The information matrix represents the information contribution of the corresponding estimate to overall estimation. Inspired by the above theory, the infinite norm of the information matrix is used to maximize the information contribution of the corresponding estimate. So, the scalar weight selection scheme by using its orientation sensitivity is given by

where are the estimation information matrices. Obviously, the results for four subsystems can be generalized to subsystems.

3.4. Distributed CI Fusion Algorithm with Information Feedback

Generally, the CI fusion algorithm only provides a consistent estimate and does not feedback the fusion information to the subsystems. However, when the subsystems are unobservable, the state maybe has a poor estimate, and the CI fusion results maybe have a poor performance under the above algorithm. So, feeding back the fusion results in the master filter to the local filters for the subsystems is a suitable choice for the Mars entry navigation scheme.

In this section, the information feedback rule will be given, and the rule includes the feedbacks of the state estimate and covariance. Figure 4 shows the distributed CI fusion algorithm with information feedback (DCIFAIF) for four local filters.

Figure 4: CI fusion algorithm with information feedback for four local filters.

The dynamic information distribution coefficients of the DCIFAIF are the same as the above scalar weights denoted . By applying the information distribution coefficients, the information of the master filter is feedback to four subfilters, and the local state estimate is given by

The DCIFAIF algorithm is given by three steps as follows:

Firstly, initialize the state and covariance as and , respectively.

Secondly, the four subsystems all use the EKF algorithm in Section 3.2. Each subsystem outputs its a posteriori state estimate and covariance .

Finally, the CI fusion estimation of the master filter is given by equations (19) and (20).

4. Simulation Results and Analysis

To evaluate the performance of the proposed DCIFAIF for the IMU/radio measurement integrated navigation scenario during Mars entry, MATLAB/Simulink simulations have been carried out. Three methods which are EKF, CI, and DCIFAIF are used in the Mars entry navigation simulations. The CPU of the simulation computer is Intel® Core™ i3-4150 @3.50 GHz, and the RAM of the computer is DDR3 1600 MHz 12 GB.

Initial condition in simulations is all listed in Table 1. The Mars gravitational constant is  m³/s². The true value and the estimated value of the ballistic coefficient of the Mars entry vehicle in simulation are set as 0.016 m²/kg and 0.0176 m²/kg. The acceleration bias coming from IMU is -0.03 m/s². Four possible beacons are selected to provide the two-way range measurements in the simulations, and their initial position and velocity are listed in Table 2. The initial covariance is , process noise covariance is , and measurement noise covariance is for the centralized EKF navigation scheme and and for the surface beacon and the orbiting beacon, respectively.

Table 1: Initial condition for integrated navigation.

Initial parameters
True
Estimated

Altitude
3518.2 km
3519.2 km

Velocity
5515 m/s
5525 m/s

FPA
-11.8 deg
-12 deg

Longitude
-89.872 deg
-90.072 deg

Latitude
-28.02 deg
-28.22 deg

Azimuth
5.156 deg
5.356 deg

Surface density
2-4
2.2-4

Lift-to-drag ratio
0.156
0.17

Table 2: Positions and velocities of beacons.

Beacons
Initial position (km)
Initial velocity (m/s)

Surface beacon 1
(3300, 420, 1350)
(0, 0, 0)

Surface beacon 2
(3290, 570, 755)
(0, 0, 0)

Orbiting beacon 1
(7855.7, -461.8, 749.82)
(66.2, 2206.4, -413)

Orbiting beacon 2
(3492.7, 3659.2, 215.11)
(-605.1, 97, 3232.8)

The simulation lasts 300 s, and the sampling frequency is 1 Hz. 5000 simulations are run to compute the error ellipse of the parachute deployment point and the root mean squared error (RMSE).

4.1. Simulations with No Fault Beacon

In these simulations, there are two orbiting radio satellites and two surface radio beacons to provide the two-way range measurements for the navigation system all the time. That is to say, there is no fault for the radio measurement system during the Mars entry phase.

Figure 5 shows the results for three methods in one single simulation. It can be seen that the navigation accuracy of the CI is the worst in three methods because four subsystems are all unobservable. The altitude, velocity, FPA, longitude, and azimuth are divergent in the simulation in Figure 5. The EKF has the best performance in simulation, because all the measurements are sent to the centralized filter algorithm, the system has stronger observability, and the uncertain parameters are augmented into the state to estimate. The performance of the proposed DCIFAIF between the CI and the EKF, the feedback state estimates, and covariance are conducive to degrade the uncertainties in the CI algorithm and increase the navigation accuracy. Furthermore, the required one-step CPU times for the above filters are listed in Table 3. In this table, it can be seen that the proposed DCIFAIF is the most efficient algorithm. The CI algorithm is the slowest, because the suitable scalar weights are computed by the determinant of the covariance.

Figure 5: State estimate errors for three algorithms.

Table 3: CPU time of one-step simulations in MATLAB.

Filter
EKF
CI
DCIFAIF

CPU time (sec)
0.0417
0.0600
0.0190

The state estimate errors and 3σ bounds of the DCIFAIF are shown in Figure 6. From Figure 6, all the six state errors of the DCIFAIF are captured by its three-sigma covariance bounds. Figure 7 shows the information distribution coefficients in the same simulation with Figure 6. Obviously, the coefficients change frequently to adapt the estimates of four subsystems and obtain better navigation accuracy. and are the coefficients of the surface radio beacons, and and are the coefficients of the orbiting radio beacons. From Figure 6, it can be seen that the surface beacons provide more contribution than the orbiting beacons during the Mars entry phase.

Figure 6: State estimate errors and 3σ bounds for DCIFAIF.

Figure 7: Information distribution coefficients in one simulation.

Figure 8 shows the RMSEs of EKF, CI, and DCIFAIF by using the logarithmic scales under 5,000 simulations. Obviously, the CI method has the biggest RMSEs, the EKF has the smallest RMSEs, and the RMSEs of the proposed DCIFAIF are between that of CI and that of EKF.

Figure 8: RMSEs for three methods during Mars entry.

4.2. Simulations with One Fault Beacon

In these simulations, one beacon breaks down in some times and cannot provide the two-way range measurements for the navigation system. Here, we assume that the last orbiting beacon has a fault after 200 s in the simulations, and only three two-way range measurements are provided for the navigation system during the Mars entry phase.

Figure 9 shows the state estimate errors and 3σ bounds of the DCIFAIF in one single simulation when the last orbiter has a fault from 200 s to 300 s. From Figure 9, the navigation errors become bigger when the fault occurs, but all the six state errors of the DCIFAIF are also captured by its three-sigma covariance bounds.

Figure 9: State estimate errors and 3σ bounds for DCIFAIF when fault occurs.

Figure 10 shows the RMSEs of EKF, CI, and DCIFAIF under 5,000 simulations when the last orbiter has a fault from 200 s to 300 s. In these simulations, the EKF is divergent from 200 s to 300 s, because no measurements are provided for the centralized navigation system. Obviously, the results of the CI and proposed DCIFAIF all become worse when the fault occurs. Also, the proposed DCIFAIF has a better performance in altitude, longitude, and latitude.

Figure 10: RMSEs for three methods when faults occur during Mars entry.

As a whole, the proposed DCIFAIF uses the distributed framework for the Mars entry navigation scheme and provides robust and reliable state estimates for the Mars entry vehicle.

5. Conclusions

Robust, reliable, and high-precision Mars atmospheric entry navigation is the key requirement for the future Mars exploration missions. Based on the CI fusion algorithm and distributed framework, this paper presented a distributed CI fusion integrated navigation algorithm with information feedback during the Mars atmospheric entry. A distributed integrated navigation scheme includes four subsystems, in which each subsystem consists of an IMU and one radio beacon. Each subsystem independently estimates the Mars entry vehicle state by using EKF, and then, these estimations are sent to the master filtering and fused by using the CI algorithm. Unfortunately, each subsystem is weakly observable under limited Mars entry measurements. A new fast-distributed scalar weight selection scheme is proposed to maximize the information contribution of the corresponding estimate by using the infinite norm of the matrix. The distributed framework with dynamic information distribution coefficients based on the CI fusion algorithm is designed to meet the lower computation cost and robust and reliable capacity. Especially, the proposed DCIFAIF can provide consistent estimate results when the subsystems are weakly observable or unobservable during the Mars entry navigation scheme with only IMU and one radio measurement. Numerical simulations show that the distributed CI fusion integrated navigation algorithm can provide consistent navigation accuracy and improve the entry navigation robustness and fault tolerance under the weakly observable navigation subsystems.

Data Availability

The data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

The work described in this paper was supported by the National Nature Science Foundation of China (grant number 61603346), the Key Science and Technology Program of Henan Province (grant numbers 172102210541 and 82102110014), the Key Research Projects of Henan Higher Education Institutions (grant number 18A413003), the Henan Province Natural Science Foundation (grant number 182300410191), and the Fundamental Research Programs for the Provincial Universities (grant number 15KYYWF01). The authors fully appreciate the financial support.

References

S. Li and X. Jiang, “Review and prospect of guidance and control for Mars atmospheric entry,” Progress in Aerospace Sciences, vol. 69, pp. 40–57, 2014.

R. D. Braun and R. M. Manning, “Mars exploration entry, descent, and landing challenges,” Journal of Spacecraft and Rockets, vol. 44, no. 2, pp. 310–323, 2007.

J.-F. Lévesque and J. D. Lafontaine, “Innovative navigation schemes for state and parameter estimation during mars entry,” Journal of Guidance, Control, and Dynamics, vol. 30, no. 1, pp. 169–184, 2007.

E. G. Lightsey, A. E. Mogensen, P. D. Burkhart, T. A. Ely, and C. Duncan, “Real-time navigation for mars missions using the mars network,” Journal of Spacecraft and Rockets, vol. 45, no. 3, pp. 519–533, 2008.

Z. Yu, P. Cui, and S. Zhu, “Observability-based beacon configuration optimization for mars entry navigation,” Journal of Guidance, Control, and Dynamics, vol. 38, no. 4, pp. 643–650, 2015.

T. Lou, H. Fu, Y. Zhang, and Z. Wang, “Consider unobservable uncertain parameters using radio beacon navigation during Mars entry,” Advances in Space Research, vol. 55, no. 4, pp. 1038–1050, 2015.

Y. Ou, H. Zhang, W. Zheng, and Y. Wang, “Autonomous land beacon selection for spacecraft navigation around Mars,” in 2017 Chinese Automation Congress (CAC), pp. 2707–2710, Jinan, China, 2017.

T. Lou and L. Zhao, “Robust Mars atmospheric entry integrated navigation based on parameter sensitivity,” Acta Astronautica, vol. 119, pp. 60–70, 2016.

S. Li, X. Jiang, and Y. Liu, “High-precision Mars entry integrated navigation under large uncertainties,” Journal of Navigation, vol. 67, no. 2, pp. 327–342, 2014.

T. S. Lou, Research on self-calibration filtering method of the dynamic model and measurement model during Mars entry, [Ph.D. thesis], Beihang University, Beijing, China, 2015.

S. Li, X. Jiang, and Y. Liu, “Innovative Mars entry integrated navigation using modified multiple model adaptive estimation,” Aerospace Science and Technology, vol. 39, pp. 403–413, 2014.

T. Lou, H. Fu, Z. Wang, and Y. Zhang, “Schmidt-Kalman filter for navigation biases mitigation during Mars entry,” Journal of Aerospace Engineering, vol. 28, no. 4, 2015.

J. L. Crassidis and J. L. Junkins, Optimal Estimation of Dynamic Systems, Chapman & Hall\CRC Press, Boca Raton, FL, USA, 2nd edition, 2012.

Y. Wang and X. R. Li, “Distributed estimation fusion with unavailable cross-correlation,” IEEE Transactions on Aerospace and Electronic Systems, vol. 48, no. 1, pp. 259–278, 2012.

N. A. Carlson, “Federated filter for fault-tolerant integrated navigation systems,” in IEEE PLANS '88.,Position Location and Navigation Symposium, Record. 'Navigation into the 21st Century', pp. 110–119, Orlando, FL, USA, 1988.

X. Wang, Z. You, and K. Zhao, “Inertial/celestial-based fuzzy adaptive unscented Kalman filter with covariance intersection algorithm for satellite attitude determination,” Aerospace Science and Technology, vol. 48, pp. 214–222, 2016.

M. K. Lockwood, R. W. Powell, and C. Graves, “Entry system design considerations for Mars landers,” in AAS Guidance and Control Conference, AAS 01-023, pp. 311–345, Breckenridge, CO, USA, 2001.

R. A. Boehmer, Navigation analysis and design for Mars entry, [Ph.D. thesis], Massachusetts Institute of Technology, Cambrigde, MA, USA, 1999.

Y. Ou and H. Zhang, “Observability-based mars autonomous navigation using formation flying spacecraft,” Journal of Navigation, vol. 71, no. 1, pp. 21–43, 2018.

Z. Yu, P. Cui, and S. Zhu, “On the observability of mars entry navigation using radiometric measurements,” Advances in Space Research, vol. 54, no. 8, pp. 1513–1524, 2014.

M. Anguelova, Observability and identifiability of nonlinear systems with applications in biology, [Ph.D. thesis], Chalmers University of Technology, Gothenburg, Sweden, 2007.

Y. Ou and H. Zhang, “Mars final approach navigation using ground beacons and orbiters: an information propagation perspective,” Acta Astronautica, vol. 138, pp. 490–500, 2017.

J. C. B. de Campos Ferreira et al., “Covariance intersection-based sensor fusion for sounding rocket tracking and impact area prediction,” Control Engineering Practice, vol. 15, no. 4, pp. 389–409, 2007.

M. A. Bakr and S. Lee, “Distributed multisensor data fusion under unknown correlation and data inconsistency,” Sensors, vol. 17, no. 11, p. 2472, 2017.

O. Hlinka, O. Slučiak, F. Hlawatsch, and M. Rupp, “Distributed data fusion using iterative covariance intersection,” in 2014 IEEE International Conference on Acoustics, Speech and Signal Processing (ICASSP), pp. 1861–1865, Florence, Italy, 2014.

C. Nebelecky, Improved Decentralized Attitude Estimates Using the Covariance Intersection Algorithm, State University of New York, Buffalo, NJ, USA, 2009.

D. Franken and A. Hupper, “Improved fast covariance intersection for distributed data fusion,” in 2005 7th International Conference on Information Fusion, pp. 154–160, Philadelphia, PA, USA, 2005.