We described a wireless and monitoring system to obtain several classes of vehicle data and send them to the server via General Packet Radio Service (GPRS) in real-time. These data are consisted by on-board diagnostic (OBD) which get from the vehicle’s OBD interface, Tire-Pressure Monitoring system (TPMS) and Global Positioning System (GPS). The main content of this paper is the hardware design of the system, especially RF modules and antennas.
With the rapid development of automobiles, people need a more efficient way to manage cars. Sometimes we wish that not only drivers know the information about their cars, but also the administrator could do the same to all the cars which are the scope of his management in real-time. Even more we would like to store all the information data in the database so that we can analyze and check the history database, if needed. So the car networking has been put forward. Car networking means that we transform kinds of vehicle information into electronic singles, and we could exchange message with the outside communication systems, such as other cars, internet, and transport facilities [
Car networking architecture in early stage.
Many services which are based on Geographic Information System (GIS) are similar to this architecture, and supervisory system of school bus’s track and the remote assistance system are examples of these services. They all need to upload the GPS data in real-time and store these data for check in the future [
The in-vehicle terminal is comprised of Microprogrammed Control Unit (MCU), Single chip OBD protocol converter, GPS module, GPRS module, and RF receiver chip. Its hardware design and the function modules are shown in Figure
Hardware design structure and function of the terminal.
Even though OBD have the unified standard of application layer, there are different physical layers and network layers from different manufacturers. In order to be compatible with more manufacturers and increase the stability of the system, we choose single chip protocol converter TL718 as the protocol converter between MCU and the car’s OBD interface. TL718 supports up to 16 kinds of OBD physical layers, so it could meet the requirement completely. TL718, GPS module and GPRS module are all connected with MCU via serial port, and the communication between RF module and MCU is based on a single data line. After receiving all data from TL718, GPS, and RF receiver chip, MCU will encapsulate those data as one data packet and sent it to GPRS module, then it uploaded it to server.
As we can see, the TPMS’s communication, GPS data reception and GPRS data transmission all involve wireless communication, so we dig into the discussion on how to optimize the choice of those modules and which antennas which to match those modules to.
Some data show that there are more and more car accidents which are caused by tire burst, especially when a car is running at a high speed in summer. In most cases, the tire is very critical for the safety of the running automobile. Now, the most effective way to prevent tire burst is to monitor the temperature and pressure of the tires.
As we know, the sensor for tire pressure monitoring is installed in the tire, while the module for receiving tire pressure data should be placed within the carriage, considering that the tire is a relatively independent unit which is located outside the carriage. Moreover, it is in the high-speed rotating state when the car is running. Thus the only way to realize the communication of real-time tire pressure monitoring system is to use the wireless communication technology.
Two of the commonest frequencies used in RF communication are 433 MHz and 2.4 GHz. Compared to 433 MHz, 2.4 GHz frequency band has a lot of advantages, such as fast communication rate, good safety and convenient protocol extension. However, our system does not need a high communication rate, because the kinds of data about tire are only temperature and pressure, and they all change at a relatively slow rate (checked once per half minute). Besides, there are a limited number of tires in one car, so we can set up a simple communication network by an easy protocol.
Moreover, the higher the frequency of the electromagnetic wave, the faster the attenuation. And the attenuation is more apparent, as the main material of car is metal. With comprehensive consideration, 433 MHz frequency is a better choice, which can be used easily, and the diffraction is better as its wavelength is longer [
Although there are many types of transceiver chip in 433 MHz frequency band, considering the actual application that the tire pressure sensor works in a single launching state and the car terminal works in a single receiving state, we choose independent single launching and receiving chip to save costs and bring down power consumption. From the application perspective, the low power consumption and stable performance are the most critical factors in the TPMS system then we find that launching chip MICRF112 and receiving chip MICRF211 of Micrel company can fulfill our requirement.
Next, we need to select the matching antenna for the RF chip. According to antenna theory, when the antenna length is proportional to the wavelength of the electromagnetic wave, sending and receiving efficiency will be the highest. This brings up the question if we chose the diffraction better and longer wavelength frequency band, it also means that we choose a longer antenna. At the same time, considering the rotation of the tire, omnidirectional antenna is more suitable antenna selection. As a result, we select helical antenna for the tire pressure sensor. According to the antenna theory, as the ratio of the wavelength and the diameter of the helical antenna
For all kinds of car networking applications, GPS information is almost essential information. Because the location for moving objects is one of the most critical attributes, so, we need to improve GPS signal quality as much as possible.
In the case of the original GPS design, two frequencies are utilized; one at 1575.42 MHz called L1; and a second at 1227.60 MHz called L2. And, in order to eliminate the Faraday rotation effect of the ionosphere to signal, GPS signal is a right-handed circularly polarized, so receiving antenna is also the right circular polarization mode [
Now, we consider two GPS antennas that are commonly used, patch antenna and helical antenna. Researches indicated that it is particularly difficult to achieve the crosspolarization rejection ratio and also to achieve adequate impedance matching at both the L1 and L2 frequencies using patch antenna. Patch antennas are narrow band, and a special feed is required to achieve the desired circular polarization. However, the study on the design based on an array of square helical antennas showed that the values of cross polarization rejection patterns slope satisfy the requirements to design a high-performance GPS receiving antenna [
Taking all above factors into account, we choose the helical antennas with a low noise amplifier. In order to reduce the signal attenuation, we extend the length of the antenna and place the receiver close to the window in the same time.
The only way to send the car’s information data to server is via wireless communication. Currently, there are multiple ways to construct wireless communication system, which are mainly divided into two classes, building their own private network and directly accessing to the public network. The first way, building their own private network, can significantly improve the communication efficiency and enrich vehicular networking functions. However, the biggest problem is the huge upfront cost to build communication infrastructure. Therefore, most of the prophase vehicular networking programs choose the second way, directly accessing to the public network. The greatest advantage of this way is that initial investment is lower and it can quickly come into use. Besides, another benefit of this way is that it has a large coverage area.
As we all know, there are two types of public communication technology, 2G like GSM and 3G like WCDMA. Compared with each other, the coverage area of GSM network is very wide because GSM technology has developed for so many years, but the disadvantage of GSM is that the bandwidth is small and the relative cost is high. 3G is the most advanced communication technology, which has been used. It greatly increases the communication bandwidth, so it is suitable for the transmission of large amounts of data, such as real-time video information. However, its main disadvantage is the limited network coverage area. Currently, 3G signal only covers the downtown with a lot of crowd. This limits the use scope of 3G communication systems.
The system described in this paper aims at vehicles which do not just move among densely populated urban. However, there are many areas without 3G signal, such as the lonely stretch of highway. At present, the information monitored by the system is only some character data, no images or video information. The bandwidth requirement is small but it requires a larger network coverage area. Therefore, the final selection of the system is GPRS. The system adopts SIM900A module of SIMcom company which uses SMT package and compact size of GSM/GPRS single-chip solution. This module has been maturely used in many fields. SIM900A connected with the MCU via the serial port receives the command and data packets sent by the MCU and then send them to the specified internet address.
GPRS operates at three frequency bands, 900 MHz, 1800 MHz, and 1900 MHz. The antennas of GPRS are called Flexible Printed Circuit Board (FPCB) Antennas which are frequently used in mobile phones and other mobile devices at present. FPCB antenna has wide bandwidth which is enough to support all three frequency bands of GPRS, as well as flexible and variable forms. It is easy to be integrated into a variety of terminal equipment [
As GPRS communications just need connecting with nearby base stations (much easier than GPS communications which have to connect directly with satellites), the quality of the communication signal is generally good.
In the end, the power of the in-vehicle terminal is supplied by OBD interface which outputs 12 V DC. Then the pictures of the in-vehicle terminal are shown in Figures
The top view of the terminal.
The reverse side view of the terminal.
The server will receive three kinds of data packets, each of which has different frame formats.
The frame header “AM,” as shown in Table
Frame Format of Frame’s Header is “AM”.
1 2 | 3 7 | 8 29 | 30 41 | 42 45 | 46 48 |
| |||||
AM | Vehicle ID | GPS data 1 | GPS data 2 | Time | Vehicle speed sensor data |
49 52 | 53 55 | 56 59 |
|
116 |
| ||||
Engine RPM | Vehicle speed sensor data | Engine RPM |
|
END |
The frame header “BM,” as shown in Table
Frame Format of Frame’s Header is “BM”.
1 2 | 3 7 | 8 29 | 30 41 | 42 45 | 46 48 |
| |||||
BM | Vehicle ID | GPS data 1 | GPS data 2 | Time | Engine coolant temperature |
49 51 | 52 54 | 55 59 | 60 |
| |||
Battery voltage | Intake air temperature | Distance travelled while MIT is activated | END |
The frame header “CM,” as shown in Table
Frame Format of Frame’s Header is “CM”.
1 2 | 3 7 | 8 29 | 30 41 | 42 45 | 46 49 |
| |||||
CM | Vehicle ID | GPS data 1 | GPS data 2 | Time | Tire A1 pressure |
50 52 | 53 57 | 58 61 |
|
74 |
| ||||
Tire A1 temperature | Tire A2 pressure | Tire A2 temperature |
|
END |
Based on this data, user could check the car’s information via a browser to access the server. People can review the history vehicle track and the running state of the car, as shown in Figure
User interface via a browser of the system.
Software interface of TPMS data.
The results successfully show that the system can acquire and transmit a lot of imported data about vehicle. As making the most of those vehicle information, this system has broad prospects. This system can play the roles of Black Box for car. The running state data are very useful to analyze traffic incidents causation then it can be applied to insurance claims processing. And it could also be used in remote assistance system, by analyzing the diagnostic trouble codes.
The authors are thank for the help provided by the “The Key Technology And Application of Intelligent Identification” Priority Scientific and Technological Innovation Team from Zhejiang province (2010R50010).