Switchable Electromagnetic Bandgap Surface Wave Antenna

This paper presents a novel switchable electromagnetic bandgap surface wave antenna that can support both a surface wave and normal mode radiation for communications at 2.45GHz. In the surface wave mode, the antenna has a monopole-like radiation pattern with a measured gain of 4.4 dBi at ±49 and a null on boresight. In the normal mode, the antenna operates like a back-fed microstrip patch antenna.


Introduction
Many types of wearable antennas have been proposed in recent years designed for body area networks (BANs).Antennas may operate in either of two modes, on-body and offbody.On-body communication refers to the transmission of signals across the human body as a surface wave, which requires the wearable antenna to have maximum directivity along the body surface while, in the off-body (normal) mode, the communication occurs away from body to a node such as a base station, which demands that the antenna have the maximum radiation in the boresight direction.Therefore ideally such antennas have to be designed to support each mode of operation.For many antennas, it is useful if they are able to operate without being affected by their environment, for example, radiating into the human body or placing them on metal surfaces such as vehicles.Hence, a large ground plane or electromagnetic bandgap (EBG) structure may be also necessary to reduce the detuning effect and the backward radiation.Some antenna designs using EBGs as artificial magnetic conductors (AMCs) have been reported in [1][2][3][4][5] for off-body communication and in [6][7][8] for on-body communication.Only a small number of papers have studied a switchable system which can support both on-and off-body communications [9][10][11].
The mushroom-like EBG structure has been well studied and widely used in various designs to improve antenna performance [1,12,13].Recent research also observed that the surface wave bandgap may disappear when the vertical vias are removed from the mushroom-like EBG structure.Hence instead of being suppressed, a strong surface wave can be exited and radiated on the via-less EBG material.Based on this feature, several surface wave antennas (SWA) have been designed to achieve a monopole-like radiation pattern on a thin, planar structure [14,15].However, in previous designs, the antenna could only support surface wave communication, and it was difficult to achieve the normal mode communication feature as the antenna was fully covered by the EBG cells.
This paper presents a novel switchable surface wave antenna based on bandgap materials which keeps the planar structure and low thickness but can support both surface wave (on-body) and normal (off-body) modes of communication at 2.45 GHz.Although not designed on textile materials, this paper shows the techniques for generating a dual mode switchable antenna.The performance of the antennas is investigated based on numerical and experimental methods.CST Microwave Studio was used for the antenna simulations.The surface wave communication mode is further investigated by studying the use of an EBG to couple antennas/sensors together around the body.

Antenna Design
The proposed switchable surface wave antenna comprises three layers.The radiating antenna is a 27 mm × 26.5 mm microstrip patch printed on a grounded slab and back-fed by a SMA connector (Figure 1).The feeding point is 6 mm offset

Simulation and Measurement
3.1.Simulation.Initially, the EBG layer, with parasitic patch inclusion, was spaced a distance, t, from the fed patch.Figure 3 plots the simulated y-z plane radiation patterns of the patch antenna alone and the patch antenna with the EBG surface for varying distances, t.For easy comparison, all radiation patterns in this paper are normalized.From Figure 3, the peak power from the radiation pattern varies from boresight for the patch antenna to approximately 50 ∘ with the EBG when the separation, t, is set to 4 mm and a null appears at boresight.There is an appreciable amount of radiation directed sideways from the antenna, along the EBG.It is also found in Figure 4 that the antenna matching performance was not significantly affected, maintaining the resonance at about 2.4 GHz.The operation of the EBG antenna is clearly shown by the current distributions on the surface in the two modes (Figure 5).For the PIN diodes shorted in Figure 5(a), the currents are confined to the parasitic patch and the six elements of the EBG closest to it which form the antenna radiating away from the patch.With the PIN diodes open circuit, the whole of the EBG is excited directing the radiation along the antenna surface.caused by the inaccuracy of the manufacture as a thin air gap is noticed when the antenna top layer and lower layer are assembled together.Unlike in previous EBG surface wave antennas reported in [14,15], where the resonant frequency highly depends on the EBG, the matching performance of proposed antenna in this paper is only slightly affected when the top EBG structure is switched, giving an opportunity to tailor the antenna radiation pattern without changing the resonant frequency.

Measurement.
The measured y-z plane radiation patterns for the switchable surface wave antenna are plotted in Figure 7.In the surface wave mode, the antenna has the maximum directivity at ±49 ∘ with a measured gain of 4.4 dBi and a null is also obtained in the boresight direction.When switched to the normal mode, the antenna mainly radiates towards the boresight direction (red dotted line in the figure) with a gain of 3.7 dBi.It is also noted, due to the large ground plane, that the antenna has low backward radiation in both modes.Overall, the simulated and measured performance of the antenna are in good agreement.

EBG Waveguide
The switchable antenna presented in the previous sections allows reconfiguration of the radiation pattern.For applications such as body worn antennas, there is a need to acquire data from a number of sensors and antennas around the body to a central node for transmission to a base station far away from the body.This is difficult to achieve by line of sight due to blockage by the body and losses tend to be very high at >40 dB.Transmission lines could be used to connect the sensors but in this section, the potential use of an EBG propagating the surface wave mode will be presented.This follows directly from the study above.The concept is shown in Figure 8 where two switchable antennas are connected together using the EBG designed in Section 2 and operating in the surface wave mode.The antennas remain switchable and are separated from centre to centre by 315 mm.The bandgap surface is shown as 3 elements wide by 6 elements long but this is for demonstration only and can be extended lengthwise as required.Three unit cell elements in width are sufficient for the EBG to operate satisfactorily rather than 2 elements.Five-element width was also tested, but there was no significant improvement obtained on transmission performance.
Figure 9 shows the surface currents for the cases with the PIN diodes both open and short circuit and it is clear that the EBG propagates a wave from one antenna to the other when the diodes are open circuit.The transmission coefficients, S 21 , for both cases are plotted in Figure 10 where simulations and measurements are compared.When the PIN diodes are    open circuit, the measured transmission was −21 dB between the antennas while the calculated value was about −23 dB.
When the PIN diodes were short circuited, the transmission between the antenna and the EBG is considerably reduced (see Figure 5(a)) and hence the EBG carries little signals to the other antenna and the measured transmission falls to −33 dB for the measurement and −41 dB in the simulation.Manufacturing difficulties probably account for the discrepancy between the measured and calculated results as there was a small uneven air gap between the layers of the structure.In addition, for the simulation, the PIN diodes are assumed to be perfect switches.
Figure 11 shows the simulated 3D radiation pattern from the whole structure when operating in the normal mode showing that the full structure with the EBG was able to switch between the normal mode (radiation away from antenna) and the surface wave mode with the EBG acting as a transmission medium as in Figure 9.
To further demonstrate propagation across the antennas with and without the connecting EBG, the antenna system is bent around a tissue equivalent phantom [6] with a diameter of 100 mm as shown in Figures 12(a) and 12(b) respectively.In Figure 12(c) the surface currents excited on the antenna structure are shown in both cases.From Figure 12(c), it is clear that the EBG propagates the wave around the bend to the second antenna.
The simulated transmission coefficients (S 21 ) are plotted in Figure 13 for the bent geometry and compared with the value when the surface was flat.The coupling for the curved surface with the EBG increases from −45 dB without the EBG to −23 dB, although it does not reach the value of −18 dB for the flat surface with EBG.Typical S 21 between antennas located at top and bottom of this tissue equivalent phantom is below −40 dB [6].

Conclusion
This paper presents a novel EBG surface wave antenna which can be switched by PIN diodes to support surface wave and normal mode communications at 2.45 GHz.In the surface wave mode, a monopole-like radiation pattern is obtained with a measured gain of 4.4 dBi at ±49 ∘ .In the normal mode, the antenna mainly radiates towards the boresight direction.Coupling two antennas together using the EBG design in surface propagation mode allows the wave to travel round a bent surface while maintaining the radiation pattern switching ability.Due to the thin and planar structure, the EBG surface wave antenna could be easily incorporated into clothing for body worn applications.Coupling losses using the EBG are better than direct radiation coupling between the antennas (typically −50 dB) when the signal travels round the torso.

Figure 6
presents the measured reflection coefficient of the switchable surface wave antenna to be compared with the simulation in Figure4.In both modes (pin open and short circuit), the antenna has −10 dB bandwidth covering 2.4 GHz to 2.47 GHz.The antenna working band is shifted upwards by 20 MHz, covering the band from 2.42 GHz to 2.49 GHz in the measurements.This may be

Figure 7 :Figure 8 :
Figure 7: Measured radiation patterns of switchable surface wave antenna in y-z plane for pin diodes open and short circuit.

Figure 9 :
Figure 9: Surface currents on EBG coupled antenna system.

Figure 11 :
Figure 11: Radiation pattern for complete antenna/EBG with PIN diodes short circuit, normal mode.