Novel Low-Cost Integrated Multiband Antenna Design Customized for Smartwatch Applications with SAR Evaluation

+is paper presents a novel low-cost integrated multiband antenna design customized for smartwatch applications and wearable devices. +e design consists in using a broadband planar patch antenna with circular microstrip lines and a miniaturized feedingpoint with a structure of 30× 30×1.6mm, and it is easy to deploy inside the smartwatch and cost-effective for the wearable device industry. +e parametric study and final dimensions of the design and the measured results of the reflection and radiation pattern are discussed. +e antenna with maximum gain up to 6.6 dBi and S11 up to −22 dB exhibits excellent performance for all the frequencies required in wearable systems such as 1.9GHz, 2.3GHz, 2.4GHz, 2.6GHz, 5.2 GHz, and 5.8 GHz. We drew a comparison between similar research and this work in terms of antenna performance. Furthermore, we investigate the specific absorption rate (SAR) performance of the antenna for the smartwatch application, using both human hand wrist multilayer and SAM head mouth models. +e SAR results in different positions for all the frequencies are compared to the Federal Communication Commission (FCC) standards.


Introduction and Motivation
Wearable intelligent devices are nowadays an exciting new frontier and have become widely used in daily life. ey are rendering the coming era of the Internet of ings (IoT); especially, smartwatches, after the success of smartphones, have attracted a lot of attention from industries and audiences [1]. Today, smartwatches and smart wristbands are experiencing a speedy development with strong demand in the mobile component market. However, they lack a multitechnology network connectivity [2]. Most of the smartwatches, due to their small size, contain antenna operating only in the ISM Band (Bluetooth and Wi-Fi) [3].
Significant progress is noticed in research regarding smartwatches and wearable devices antennas. An excellent comparison between microstrip patch, helical, and conical spiral antenna is developed in [4]. A multiband antenna operating in GSM900, LTE2300, and UMTS1900 is proposed in [5], the structure of the design sizes 55 × 12 × 4 mm 3 which make the antenna unsuitable for smartwatches. A miniaturized implantable ARRAY antenna was proposed in [6] and in [7], both array designs cover the GPS band entirely, but both of them do not cover the LTE bands and present big size. Wang et al. proposed a miniaturized antenna for GPS applications in [8], but the proposed antenna is difficult to manufacture and does not cover the UMTS or the LTE bands. Also, using a low-profile miniaturized antenna in [9], the authors present a good antenna that covers the LTE bands but the ISM band is not covered. In [10], a built-in antenna works perfectly in GPS and ISM bands, and the antenna is suitable for wearable devices such as smartwatch, but it is built with complex materials. In [11], Mehedi et al. designed a compact metamaterial-inspired antenna which operates at LTE and WiMAX frequency bands. Still, the ISM band is missing and the antenna presents a large size for smartwatch implementation. Zhao et al. proposed in [12] three cellular antenna designs for the smartwatch application by using the metal watch belt. e three designs cover the ISM, UMTS, and GSM bands entirely, but all of them are big-sized and complex for implementing inside the smartwatch. In [14], Hasan et al. suggested a tri-band microwave perfect metamaterial absorber with miniature structure up to 10 × 10 × 1.6 mm 3 ; however, the design resonates at higher frequency bands 6.22 GHz,8.76 GHz, and 13.05 GHz, which are not suitable for smartwatch application. Cheuk et al. designed in [15] a miniaturized printed inverted-F antenna for the Internet of ings, which sizes 15 × 30 mm 2 but works only in the ISM and. An Electrically Compact SRR-Loaded Metamaterial Inspired Quad-Band Antenna for Bluetooth, Wi-Fi, WLAN, and WiMAX System is proposed in [16]; despite its complexity, the design is miniaturized sizing 30 × 31 mm 2 and potentially suitable for wearable devices. e objective of this research is to design a miniaturized integrated multiband antenna for smartwatches and wearable devices. e proposed antenna must operate in the following technologies UMTS1900, LTE2300, ISM2400, LTE2600, WIMAX5200, and ISM5800, satisfying the prerequisites in terms of gain, radiation pattern, current distribution, total efficiency, and reflection coefficient in each. Furthermore, the parametric study of the proposed antenna is discussed, and the influence of each parameter on the antenna performance in term of the reflection coefficient is presented. To ensure the compliance of the antenna against the FCC standards, the impact of design in terms of the SAR performance for the smartwatch application was evaluated. We used both the SAM head model provided by CST Studio and the human hand wrist model, designed based on the following layers: skin, fat, muscle, and bone. e SAR evaluation is calculated for the all selected frequencies and for different antenna positions: d � 1 mm, d � 2 mm, d � 4 mm, and d � 7 mm for antenna on hand wrist configuration and d � 1, d � 5 mm, and d � 9 mm for antenna next to SAM mouth configuration.

Smartwatch Evolution and Hand
Model. Smartwatches are now enjoying great success as the new technological trend in the mobile device market. anks to their ideal portability while inheriting the charm of classic watches, these devices are becoming more and more competitive by acquiring the features existing in smartphones. e criteria for the progression of smartwatches are reflected in their design, battery autonomy, and especially the development of applications compatible with the miniature display.
While internal hardware layers differ from a brand to another, most smartwatches have an electronic front display, either backlit LCD, OLED, or hologram [4]. Some use transflective or electronic paper, to consume less power. A rechargeable lithium-ion battery generally recharges them. Peripheral devices may include digital cameras, thermometers, accelerometers, pedometers, heart rate monitors, altimeters, barometers, compasses, GPS receivers, tiny speakers, and microSD cards, which are recognized as storage devices by many other kinds of computers. e software may include digital maps, schedulers and personal organizers, calculators, and various types of watch faces.
In smartwatches, efficient wireless performance is essential. Users expect these devices to last all day and stay connected all day. With the added challenges of implementing multiple antennas in an ultracompact form, it is absolutely essential to consider a multiband design to minimize space. is design should not contain any active component to reduce power consumption and should be miniaturized as much as possible to fit inside the device. As smartwatches can communicate with external devices such as sensors, wireless headsets, or machines, several wireless technologies may be required. In fact, a smartwatch can collect information from internal or external sensors and control or retrieve data from other instruments or servers via a local wireless network and then send it to an external server via the internet or long-range wireless network. For this reason, the proposed antenna should support the most popular wireless technologies such as UMTS1900, LTE2300, ISM2400, LTE2600, WIMAX5200, and ISM5800.

Antenna Requirement.
e objective of this research is to design an integrated antenna having a planar structure and easy to manufacture, and such antenna is very suitable for smartwatch applications. e antenna should be miniature as possible and easy to deploy inside the smartwatch. e antenna must fit inside the smartwatch configuration as presented in Figure 1. e fact of implementing the antenna inside the smartwatch protects the antenna from vandalism, but it makes the wireless communication much difficult within a metal environment where the communication path is strongly influenced by the shielding of conductive layers. Since the smartwatch contains already conductive printed circuit boards (PCBs).
To ensure a general use case of the antenna, we selected the famous common bands in which our terminal should radiate. e target bands are listed in Table 1.
Regarding this frequency band specification, the antenna will ensure the IoT data acquisition through the IoT band and the data transmission through UMTS/LTE/WIMAX bands. e ISM bands can be used for local data transmission and to enable the IoT (communication with other devices). In each of the frequency bands listed in Table 1, the antenna must demonstrate compliance regarding its influence in terms of SAR on the wrist hand model presented in Figure 2 and the SAM head model.

Configuration and Parametric Study.
We started from an off-the-shelf planar antenna to obtain a low-cost design. We first design the UMTS/LTE2300/ISM band using the correlation between frequency and wavelength. Afterward, we create step by step the other bands also based on wavelength and taking into account that each new arm must not interfere in terms of the frequency band with the neighbor arm and must fit the sizing specifications of the antenna. In each designing step, we observe and study the current distribution in each frequency in order to adjust and optimize the structure.
e configuration (a) refers to the coupling 2 International Journal of Antennas and Propagation between circuit (A) and the ground, giving the UMTS1900 and WIMAX5200 bands, whereas the configuration (a + b) refers to the coupling of circuits (A) and (B) ensuring the ISM2400 and LTE2600 bands and the enhancement of WIMAX5200 band. e configuration (a + b + c) is the coupling of circuits (A), (B), and (C) and the ground giving the band LTE2300 and providing additional enhancement to the other bands. Figure 3 shows the four necessary steps of the conception of the design. Each step represents a target band, and in each stage, there was many simulations and iteration performed to obtain the best reflection coefficient. In Figure 4, we show the S 11 result of each step and how the antenna resonates with each arm. e final results show additional frequencies obtained due to the mutual coupling between the components of the antenna.

Final Design.
e feeding line sizes 2 × 7 mm 2 . e substrate made of FR4 material has a relative permittivity of 4.3 and a dielectric tangent loss up to 0.02, and it sizes 32 × 35 × 1.6 mm 3 . e soldering spaces are modelled as PEC surfaces sizing 2 × 4 mm 2 . Table 2 summarizes the dimensions of the proposed antenna design and gives the value in mm of each parameter of the structure of the configuration shown in Figure 3.

Manufacturing and Measurement Results
In this section, the fabricated antenna is presented and obtained measurement results for the S 11 , radiation pattern, gain, and current distribution are discussed.

Manufacturing.
e proposed antenna model is fabricated using the LPKF ProtoLaser S systems which can process highly complicated tasks with printed circuit boards (PCBs). e machine is very efficient for cutting assembled PCBs, flexible PCBs, and cover layers. e manufactured antenna shown in Figure 5 was printed on an FR4 substrate, where the characteristics are listed in Table 2, and cut using the Maestro3 machine.

Measurement Setup.
To measure the S 11 of the antenna, the vector network analyzer (VNA) Agilent N3383 A 300 kHz-9 GHz is used, and it is calibrated in each simulation with the Agilent 85033E 3.5 mm calibration kit. e antenna was attached to the VNA through the Keysight 8121-0027 cable.
To perform the radiation pattern measurements, the double-ridged TEM horn antenna is used with Lens GZ0226DRH intended for indoor and outdoor ultrawideband applications. e radiation measurement setup is described in Figure 6. e far-field antenna measurement system principle of operation is based on pulse measurement technique (time-domain measurements, TD). is system is applicable for most types of antennas and carries up sizes at distances R between antenna under test (AUT) and measuring antenna larger than far-field criteria [27]: where D is the section (aperture) of antenna and λ is the wavelength. As main measurement instrument, the digital sampling converter is used. Its characteristics are optimized according to the system's parameters. e ultrashort-pulse electrical generator serves as measurement signal source. e systems are built for frequency ranges 6 GHz, 12 GHz, 18 GHz, 26 GHz, and 40 GHz [27].

S 11 Measurement Results.
e simulation results compared to the measurement results in free space in terms of S 11 with respect to 50 ohms are represented in Figure 7.
e measurement results confirm the results of simulation done with CST Studio software where all the target frequency bands fit the simulation resonance bands with small shift for the lowest frequencies up to 0.2 GHz. e first main reason is the line added in the manufactured design and one of the possible reasons explaining the larger bandwidth obtained in measurements is the multipath effect obtained by the environment where the measurements are performed and which is absent in the simulations. e results prove that the antenna meets perfectly the requirements in all the frequency bands discussed previously.  e radiation pattern of the gain in 2D plot (Phi � 0 and Phi � 90) is presented for each frequency at elevation view in Figure 8, and at azimuth view in Figure 9.
From the results plotted in Figures 8 and 9, it is observed that the antenna is approximately omnidirectional and it exhibits a higher gain for all the specified frequency bands. e best result in terms of radiation pattern shape is obtained for 2.3 GHz, for 2.4 GHz, and for 2.6 GHz where the antenna is clearly omnidirective and the corresponding maximum measured gains, respectively, are 3 dBi, 4.9 dBi, and 4.4 dBi. e antenna is more directive at 5.8 GHz with a maximum gain up to 6.6 dBi. e Figure 10 shows the variation of the measured maximum gain in dBi in function of the frequency. It is noticeable that the minimum gain is 2 dBi obtained at 1.9 GHz and the maximum gain is 6.6 dBi at 5.8 GHz, and this means that the antenna has a high maximum gain over all the target frequency bands. e total efficiency over frequency of the proposed design is presented in Figure 11. For the UMTS1900 and WIMAX5200 bands, the efficiency varies from 60% to 80%, but only around 60% for WIMAX5200 and LTE2300. e best results are obtained for ISM2400 and LTE2600 where the antenna total efficiency is 80%.
e Figure 12 represents the current distribution of the antenna in each frequency, showing which parts of the design interact to construct the target band.

Influence of the Smartwatch.
After evaluating the reflection and the radiation measurements of the antenna in free space, the impact of the smartwatch on the performance of the antenna in terms of S 11 is investigated. e radiation is not concerned since the smartwatch is a dielectric box with a relative permittivity of 2.3 and thus it does not prevent and or reflect the propagation of the antenna waves.   Figure 13 shows the influence of the smartwatch cover on the S 11 parameter of the antenna. e S 11 results of the antenna inside the smartwatch are compared to the S 11 results of the antenna in free space. Four positions of the antenna were selected for this comparison: 0 mm (antenna attached to the cover of the smartwatch), 1 mm, and 2 mm separation of the antenna to the cover. As shown in Figure 13, it is noticeable that when the antenna is attached to the cover, the measured S 11 of the antenna is increased dramatically. Starting from 1 mm as a separation, the S 11 results get closed to the free space results. is explains why a gap between the antenna and the cover of the smartwatch is necessary. Table 3 shows the comparison between the proposed antenna and existing antennas based on size, coverage, bandwidth, gain, and applications.

SAR Studies
In this section, we evaluate the SAR performance of the antenna in two main scenarios: antenna mounted on the human hand wrist and antenna next to the human head mouth relevant for smartwatch with integrated microphone functionality. e SAR values are examined according to the standard limits defined by the FCC standards, which is 2 W/ kg averaged over 10 g of tissue of the human head and 4 W/ kg averaged over 10 g of tissue of the hand wrist [17,[19][20][21][22][23][24][25][26]. Figure 14(a) shows the position of the smartwatch antenna on the hand model with human hand tissues layers used for the SAR simulation with CST studio software, and Figure 14(b) shows the position of the smartwatch antenna next to the SAM head model provided by CST studio software. Figure 15 shows the setup of the antenna on the hand model. e antenna is placed in the center of the wrist at the top. To evaluate the SAR in each frequency, we choose four central values for the distance as separation between the antenna and the hand wrist: d � 1 mm, d � 2 mm, d � 4 mm, and d � 7 mm. We designed a three-dimensional human hand model with four tissue layers: skin, fat, muscle, and bone. Table 4 summarizes the characteristics in terms of dielectric property and conductivity at each frequency for each tissue.

Antenna on the Hand Wrist.
e SAR values averaged over a mass of 10 g of hand wrist tissue, for d � 1 mm, d � 2 mm, d � 4 mm, and  International Journal of Antennas and Propagation d � 7 mm, for each frequency and at each tissue layer, are summarized in Table 5. From the results obtained, it can be seen that the maximum SAR values in hand wrist case are below the limits 4 W/kg specified by the FCC standards. We notice that for all the frequencies in scope and at each distance, the SAR value calculated in fat tissue is in average 0.01 W/kg higher than the SAR value calculated in skin tissue. is can be explained by electrical properties ε r and σ (S/m) of the fat tissue that are lower than the electrical properties of the skin tissue. In the other hand, the maximum SAR value decreases from the fat tissue to muscle tissue, and then from the muscle tissue to the bone tissue. We notice that the maximum SAR within the same tissue decreases as the frequency increases. In average, the maximum SAR decreases from 2.3 GHz to 5.8 GHz by 70% at the skin, fat, and muscle layers and by 45% at the bone layer. Figure 16 shows the three-dimensional distributions of the SAR (W/kg) averaged over a mass of 10 g simulated inside the hand wrist model at the frequencies of 2.3 GHz, 2.4 GHz, 2.6 GHz and 3.500 GHz, 5.2 GHz, and 5.8 GHz with 5 mm spacing, using software CST MWS.
We notice that the averaged SAR over 10 g decreases slightly from the skin layer to the fat layer then decreases highly at the muscle layer to the bone. e values of the average SAR is higher in the center top of the wrist than the edges, which can be explained by the position of the antenna placed on the center of the hand wrist.  Based on results obtained, we notice that all SAR values, at each hand wrist layer, fit the SAR requirements defined by the FCC standards 4 W/kg for the hand wrist.

Antenna next to SAM Mouth.
In this configuration, the antenna is placed next to SAM mouth. We selected three values of the separation between the antenna and SAM International Journal of Antennas and Propagation mouth: d � 1 mm, d � 5 mm, and d � 9 mm. e simulated values of the maximum SAR averaged over a mass of 10 g of the tissues of the head for the SAM phantom head, at selected frequencies, using CST MWS software, are summarized in Table 6. From the results of electromagnetic simulations, we notice that the maximum SAR values for 10 g of the head model tissue decreases when the spacing between the antenna to SAM mouth changes from d � 1 mm to d � 9 mm. In average, the SAR value decreases by 60% from d � 1 mm to d � 9 mm. It is also noticeable that the SAR value is higher at higher frequencies 3500 MHz, 5200 MHz, and 5800 MHz. We notice from the plots of SAR distribution inside SAM head that for the lowest frequencies 2300 MHz, 2400 MHz,       Based on the results shown in Table 6 and Figure 17, all the values of the SAR averaged over 10 g inside SAM head obtained at each frequency starting from a separation of 1 mm are below the SAR limits 2 W/kg defined by the FCC standards.

Conclusions
In this paper, a novel miniaturized antenna experimentally verified for wearable device applications is presented. e antenna with its simple low-cost planar structure allows manufacturer to save considerable amount of money accounting of the number of antennas required in such application in the worldwide. Comparatively, to the existing propositions, the presented antenna sizing 32 × 35 × 1.6 mm 3 is distinguished by its simplicity for manufacturing, ease of deployment inside smartwatches, and excellent performance in terms of radiation pattern, total efficiency, gain, and reflection coefficient. e antenna was fabricated and measured in terms of the radiation pattern and the reflection coefficient, the results confirm the simulations and show that the antenna is approximately omnidirectional with a maximum gain up to 6.6 dBi and S 11 up to −22 dB, and it covers all the specified technology bands used in the smartwatch devices such as UMTS1900, LTE2300, ISM2400, LTE2600, WIMAX5200, and ISM5800. For the compliance of antenna against the FCC standards, the SAR averaged for 10 g of tissue was evaluated for each frequency and for two configurations: antenna on the hand wrist model with four tissue layers and antenna next to the SAM mouth model. e maximum SAR results obtained starting from a separation of 1 mm shows compliant values below the limit 4 W/kg in the case of the hand wrist and values below 2 W/kg limit in case of SAM head.

Data Availability
e data used to support the findings of this study are available from the corresponding author upon request.  International Journal of Antennas and Propagation 13