Solid-liquid batch extraction of total polyphenol content from curry leaves (Murraya koenigii L.) was studied in this paper. The effect of different solvent concentrations and temperatures on total polyphenol content was investigated by performing batch experiments. The experimental studies showed that the kinetics of solid-liquid batch extraction was influenced by different solvent concentrations and temperatures. In solid-liquid batch extraction, more recovery of total polyphenols was obtained for 50% (v/v) aqueous methanol and at 333 K temperature. The total polyphenol obtained at optimum conditions was 79.34 mgGAE/L. Mathematical modelling is an important engineering tool used to study the kinetics of extraction as well as in the design of the extraction process to reduce time, energy, and chemical reagents. Peleg and Power law, the two mathematical models, were used to study the kinetics of the batch extraction process. The Peleg model showed the best fit to explain the kinetics of process with R2 > 0.99. Further conventional extraction methods are compared with the novel extraction method.
1. Introduction
The extraction of bioactive compounds mainly polyphenols has increased in recent years because of their medicinal value. Polyphenols are the plant secondary metabolites which constitute phenolic acids, flavonoids, stilbenes, and lignans. These are the natural antioxidants that replace synthetic antioxidants such as propyl gallate (PG), butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), and tertiary butylhydroquinone (TBHQ). The consumption of food rich in polyphenols offers better protection against the development of cancers, cardiovascular diseases, diabetes, osteoporosis, and other diseases. These compounds are found in fruits, vegetables, spices, cereals, and plants with varied concentrations [1–4]. Herbal plants are loaded with bioactive compounds such as lipids, phytochemicals, pharmaceutics, flavours, fragrances, and pigments [5]. Curry leaves (Murraya koenigii L.), a member of the family Rutaceae, is used as a spice and easily available in India. It is mostly used in curry preparation because of its characteristic flavour and aroma [6]. Curry leaves have the properties of anti-inflammatory, antidysenteric, antioxidant, antidiabetic antimicrobial, antibacterial, positive inotropic, and cholesterol-reducing activities [7, 8].
The polyphenols present in plant materials can be extracted by solid-liquid extraction process. Solid-liquid extraction is a mass transfer phenomenon in which separation and isolation of desired bioactive compounds or group of compounds from the plant matrix take place by using a suitable solvent. The extraction is a two-stage process: the fast washing stage and the slow diffusion stage. To study the extraction process, the physical and chemical properties of solute and solvent are important and solute-solvent interactions must be known [9]. The studies have been carried out by many researchers for the solid-liquid batch extraction of polyphenols from different raw materials under different extraction conditions such as solvent composition, particle size, solid-to-solvent ratio, time, and temperature [2, 10–13]. The kinetics of the extraction process is well predicted using suitable models [14]. Mathematical modelling is an important engineering tool which is used to facilitate simulation, optimisation, design, and control of processes [2]. By applying the experimental data to model equations, the parameters like mass transfer coefficients in washing and diffusion steps as well as diffusivity can be determined. Fick’s law of diffusion [15–17], first- and second-order kinetic modelling [4, 18, 19], Peleg model [2, 13, 20], Power law model [21], and two-site kinetic model [14, 19, 22] are used in the extraction study of polyphenols and other bioactive compounds from plant matrix using conventional and advanced extraction methods.
The present paper focuses on the study of the effect of solvent concentration and temperature on the recovery of total polyphenols from curry leaves by solid-liquid batch extraction. Literature data on mathematical modelling of total polyphenols from the curry leaves are scarce. To have insights into the mathematical modelling, an attempt has been made to study the extraction kinetics by the application of Peleg model and Power law model to the obtained experimental data. The conventional extraction methods are compared with the novel method in terms of percentage recovery of polyphenols.
2. Materials and Methods2.1. Plant Material
The curry leaves (Murraya koenigii L.) were collected from local market. In laboratory, the leaves were separated from stem and washed with water and finally with distilled water to remove dust and impurities. Sejali and Anur [23] found that the medicinal quality of plant parts was affected due to thermal degradation of active constituents and investigated the effect of drying process on phenolic compounds present in neem leaves powder. They observed that phenolic contents were higher in shade drying powder than oven drying at 45°C and at 70°C. So, the cleaned curry leaves were shade dried at ∼ 30–35°C for 10 days. Periodically, the weight was checked to ensure complete removal of moisture. Cleaned and dried samples were ground using a grinder machine (Jaipan). Ground samples were sieved and separated, and 36-mesh (0.425 mm) particle size material was used for further experimentation. The sample was stored in airtight containers at 4°C to avoid the direct contact with air.
2.2. Chemicals
Gallic acid (Sigma-Aldrich), Folin–Ciocalteu reagent, methanol, and anhydrous sodium carbonate (Na2CO3) of Merck were used in the study.
3. Methods3.1. Soxhlet Extraction
The thimble containing 10 g of 0.425 mm of plant material packed in a white muslin cloth was placed between condenser and round-bottom flask containing 400 mL of 50% (v/v) methanol-water solvent [24]. After boiling the solvent, the extraction chamber progressively furnishes with new solvent from the round bottom flask. When meeting the maximum level in the extraction chamber, the condensed solvent from the extraction chamber was flushed back into the round bottom flask by a siphon. This condensed solvent carries the solutes into the solvent. The extraction was performed for 7 h and sample was analysed for the total polyphenol content. The result obtained from the Soxhlet method is considered as maximum value of polyphenol concentration and the rest of the experimental values from batch and ultrasound-assisted extraction were compared with this.
3.2. Batch Extraction
The solid-liquid batch extraction was performed in a glass reactor of 300 mL capacity equipped with a three-blade marine propeller of diameter 4 cm to provide the stirring. The stirring helps in avoiding the settling of the solid particles due to gravity. The experiments were performed to study the effect of methanol-water solvent compositions (0%, 50%, and 100% v/v) and temperatures (313, 323, and 333 K) for the particle size of 0.425 mm and solid-to-solvent ratio of 1 : 40 (g/mL). The batch extraction was performed for 7 h. The samples were withdrawn at fixed intervals and filtered with Whatman No. 42 filter paper prior to analysis.
3.3. Ultrasound-Assisted Extraction
Ultrasound-assisted extraction (UAE) was performed by using ultrasound probe DP 120 model supplied by PCI Analytics, Mumbai, of 20 kHz frequency and 250 W power. The probe was operated in pulse mode (10 s on-off) to avoid heat dissipation and loss of solvent due to heat [25]. The other experimental conditions were kept similar as in batch extraction. The mixture was sonicated for 1 h using 50% (v/v) methanol-water solvent concentration and samples were withdrawn at fixed time interval, filtered, and analysed.
3.4. Determination of Total Polyphenol Content (TPC) by Folin–Ciocalteu Method
TPC was determined by the Folin–Ciocalteu method [26]. For all analysis, 1.0 mL of sample was added to at least 60 mL of distilled water in a 100 mL volumetric flask. 5 mL of Folin–Ciocalteu reagent was added to the flask and mixed. After 1 min and before 8 min, 15 mL of 20% sodium carbonate solution was added and the volume was adjusted to 100 mL with distilled water. The samples were kept in water bath at 40°C for 30 min, and the absorbance was measured at 765 nm wavelength in a 3 mL cuvette using UV double beam spectrophotometer (Model: Shimadzu UV1800, Japan). A calibration curve was prepared from gallic acid standard solutions (50, 100, 150, 200, 500, and 1000 mg/L) (R2 = 0.996) and the blank was prepared with distilled water. The total polyphenol content was expressed as mgGAE/L.
3.5. Mathematical Models
The kinetics of total polyphenols extraction by batch process was studied by fitting the obtained experimental data to Peleg and Power law model equations.
3.6. Power Law Model
The Power law model is one of the empirical equations used in kinetic study of solid-liquid extraction. The model has been used in kinetic study of camptothecin from Nothapodytes nimmoniana [21] and vanillin from Vanilla planifolia Andrews [27] by microwave-assisted extraction.
The equation for Power law model is(1)Ct=Btn,where Ct is a concentration of total polyphenols in extraction solvent (mgGAE/L) at time t (s), n is Power law exponent (<1), and B is constant related to extraction rate (L/g s).
3.7. Peleg Model
Peleg proposed a nonexponential empirical equation in 1988 for sorption curves, i.e., moisture versus time [28]. Because of the similarity between the sorption curves and concentration curves, Peleg model can also be used to explain the kinetics of solid-liquid extraction [2]. The model has been used to explain the kinetics of solid-liquid extraction of polyphenols from soybeans [13] and grape seeds [2]. The equation for Peleg model is(2)Ct=C0+tK1+K2t,where C(t) is the concentration of total polyphenols at time t (mgGAE/L), Co is the concentration of total polyphenols (mgGAE/L) at time t = 0, K1 = Peleg’s rate constant that relates the initial extraction rate (min.g/mg), and K2 = Peleg’s capacity constant that relates the maximum extraction yield (g/mg). In the solvent, the initial concentration of polyphenols is zero; hence, the term Co can be excluded from equation (2). Therefore, equation (2) is modified as(3)Ct=tK1+K2t.
3.8. Statistical Analysis
The consistency between the predicted and the experimental data was examined using the coefficient of correlation (R2) and root mean squared error (RMSE), which are defined as(4)R2=1−∑i=1nxi−x^i2∑i=1nxi−x¯2,RMSE=1n∑i=1nxi−xi^2,where n is the number of samples, xi is the experimental value of the ith sample, x^i is the predicted value of the ith sample, and x¯ is the mean value of all experimental data, with a high R2 value and low RMSE value indicating high consistency between the experimental and predicted data.
4. Results and Discussion4.1. Effect of Solvent Concentration on TPC
The selection of an appropriate solvent or solvent mixture is an important step in extraction of polyphenols from the plant matrix. The polyphenols mainly consist of phenolic acids, flavonoids, stilbenes, and lignans and have a complex structure. Hence, it is difficult to predict the solute-solvent interactions. The choice of a solvent depends on polarity, the solubility of solute in the given solvent, reactivity, safety, and cost. The polar compounds are soluble in polar solvents such as methanol, ethanol, ethyl acetate, and acetone, whereas nonpolar compounds are soluble in nonpolar solvents such as toluene, benzene, hexane, and cyclohexane. It was found that the mixtures of alcohol and water work best in extracting phenolic compounds compared to the monocomponent solvent [29]. The effect of methanol-water solvent compositions (0%, 50%, and 100% v/v) on extraction of total polyphenols by batch extraction for particle size of 0.425 mm and solid-to-solvent ratio of 1 : 40 (g/mL) and at room temperature (27°C) was studied. It was observed from Figure 1 that maximum amount of total polyphenol content of 75.42 mgGAE/L was obtained for 50% (v/v) methanol-water composition, while less concentration of total polyphenols was obtained for absolute water and absolute methanol solvents. For all solvent compositions, it was seen that initially the rate of extraction of polyphenols was higher and afterwards it remains constant approaching towards equilibrium. The concentrations obtained at 7 h were considered as equilibrium concentrations attained during extraction. The probable reason for obtaining the higher amount of polyphenols in 50% (v/v) methanol-water composition is that the addition of small amount of water to methanol increases the polarity of the medium and breaking of hydrogen bonding, thus facilitating the extraction [30]. The polarity index of 50% (v/v) methanol-water mixture is 7.05 which is higher than methanol. Also, the addition of water increases the swelling of the plant material which in turn enhances the contact surface area for solvent-solid. Increasing the concentration of methanol in solvent mixture causes protein denaturation and prevents the dissolution of polyphenols in the solvent and hence affects the extraction rate [31]. Our findings are in accordance with Jovanovic et al. [32]. They reported a maximum yield of total polyphenol of 19.6 mgGAE/L by maceration, 22.6 mgGAE/L by heat-assisted extraction, and 24.9 mgGAE/L by UAE from Thymus serpyllum leaves at 50% ethanol-water concentrations. Costa et al. [33] found 50% ethanol-water as the best solvent for the extraction of polyphenols from Thymus lotocephalus. Jokic et al. [13] also found 50% ethanol-water as the best solvent for extraction of polyphenols from soybeans by solid-liquid batch extraction. It was found from the literature that 40–60% (v/v/) alcohol-water (ethanol or methanol) works best to get the higher yield of polyphenols from the plant material. It was also reported that extraction of polyphenols from curry leaves was carried out by using water, ethanol, ethanol-water (1 : 1), hexane, and chloroform as the solvents [6] and obtained a highest yield of 168 mgGAE/g of extract from 1 : 1 ethanol-water mixture. The specific difference in results exists due to methodologies followed, experimental work, variety, and location of plant material.
Effect of solvent composition on the concentration of TPC by batch extraction.
4.2. Effect of Temperature on TPC
The temperature is an important factor influencing the extraction of polyphenols from the different plant matrices. With increasing temperature, the solubility and diffusivity of phenolic compounds increase and enhance the extraction of polyphenols. Also increasing the temperature reduces the surface tension and viscosity of the extraction medium, thus accelerating the mass transfer rate and hence extraction of polyphenols [4]. The batch extraction was performed at 313, 323, and 333 K for particle size of 0.425 mm, solid-to-liquid ratio 1 : 40 (g/mL), and methanol-water composition 50% (v/v). Figure 2 shows the positive influence of temperature on the concentration of polyphenols. The extraction of polyphenols has increased from 313 to 333 K. This increase in the concentration of TPC might be due to increased diffusivity of polyphenols into solvent. The maximum amount of polyphenols obtained at 333 K was 79.34 mgGAE/L. The rate of extraction was fast in the initial 1.5 hours, i.e., washing stage, and thereafter, it was slow in the diffusion stage. However, a too high temperature may cause loss of solvent by evaporation and thermal degradation of polyphenols may affect the efficiency of extraction [34]. Ghitescu et al. [35] observed similar results for the temperatures of 313–333 K for extraction of polyphenols from spruce wood bark by UAE. Wang et al. [36] also achieved similar results of extraction of phenolic compounds from wheat bran by increasing temperature from 298 K to 348 K.
Effect of temperature on the concentration of TPC by batch extraction.
4.3. Comparison of Kinetic Models
The experimental data obtained by performing batch extraction were analysed by using two kinetic models: the Peleg model and the Power law model. The mathematical modelling of the process helps to understand the complex diffusion and mass transfer phenomena. Evaluation of best fit among the models was done based on the value of correlation coefficient (R2) and root mean squared error (RMSE).
4.4. Peleg Model
The graph of 1/Ct versus 1/t yields the values of Peleg model constants K1 and K2. The lower values of K1 and K2 imply the faster rate of extraction and the maximum concentration at equilibrium, respectively. The calculated Peleg’s model constants K1 and K2, experimental and predicted equilibrium concentrations, and values of R2 and RMSE are shown in Table 1. The values of R2 are in the range of 0.997–0.998 and RMSE are in the range of 0.343–1.267 (Table 1). The higher values of correlation coefficients and lower values of RMSE signify that the model fits the experimental data well compared to the Power law model. With higher values of R2, Figure 3 shows good correlation between all experimental and predicted values of total polyphenol concentration for Peleg model at different temperatures and methanol-water solvent compositions.
Kinetic parameters for Peleg model and experimental and predicted equilibrium concentration values at different extraction conditions.
Parameter
K1 (g min/mg)
K2 (g/mg)
Experimental Ce (mgGAE/L)
Predicted Ce (mgGAE/L)
R2
RMSE
Temperature (K)
313
0.0046
0.0156
62.62
61.51
0.997
1.031
323
0.0041
0.0140
70.34
68.56
0.998
0.827
333
0.0047
0.0124
79.34
76.41
0.997
1.267
Methanol-water conc. (%v/v)
0
0.0112
0.0151
59.78
59.88
0.998
0.686
50
0.0156
0.0108
75.42
76.50
0.998
0.954
100
0.0006
0.0162
58.87
58.62
0.997
0.343
Correlation between experimental versus predicted values for concentrations TPC obtained using Peleg model for different temperatures (a) and solvent compositions (b).
4.5. Power Law Model
In this model, a plot of ln Ct versus ln t yields the values of Power law constants n and B. The values of the Power law model constants, R2, and RMSE are shown in Table 2. The values of R2 are in the range of 0.954–0.991, while RMSE are in the range of 0.543–4.0 (Table 2). Figure 4 shows experimental and predicted concentration values of total polyphenols for Power law model at different temperatures and methanol-water solvent compositions.
Kinetic parameters for Power law model and experimental and predicted equilibrium concentration values at different extraction conditions.
Parameter
B (L/g s)
n (g/mg)
Experimental Ce (mgGAE/L)
Predicted Ce (mgGAE/L)
R2
RMSE
Temperature (K)
313
31.14
0.116
62.62
63.01
0.978
0.613
323
35.67
0.112
70.35
70.25
0.966
0.770
333
33.36
0.142
79.34
78.85
0.991
0.543
Methanol-water conc. (%v/v)
0
15.30
0.232
59.78
62.11
0.961
1.481
50
9.252
0.357
75.42
70.25
0.954
4.00
100
26.68
0.134
58.87
59.97
0.959
0.865
Correlation between experimental versus predicted values for concentrations of TPC obtained using Power law model for different temperatures (a) and solvent compositions (b).
4.6. Comparison of Extraction Methods
UAE is a novel, clean, and green extraction method. UAE requires less time, solvent, and energy compared to conventional extraction methods. The Soxhlet extraction and batch extraction methods were compared with the UAE method. The comparison of methods in terms of percent extraction of total polyphenol content is shown in Figure 5. In all three methods, a particle size of 0.425 mm, solid-to-solvent ratio of 1 : 40 g/mL, and solvent concentration of 50% (v/v) methanol-water were maintained. Soxhlet extraction that was performed for 7 h results in total polyphenols concentration of 100.66 mgGAE/L and was considered as 100% extraction and the remaining values were compared with this base value [25]. The percentage extraction obtained by batch extraction for 7 h was 74.92% whereas percentage extraction by ultrasound assistance was 65.68% in 1 h of duration. Though higher recovery of polyphenols was obtained in Soxhlet extraction, it requires more time and energy. UAE results in better recovery of polyphenols than the conventional methods. Since in UAE due to acoustic cavitation, the rupture of plant cells occurs, facilitating the diffusion of solute into the solvent and thus enhancing the efficiency.
Comparison of extraction methods for particle size 0.425 mm, solid-to-solvent ratio 1 : 40 (g/mL), and solvent concentration of 50% (v/v) MeOH-water.
5. Conclusion
The kinetics of solid-liquid batch extraction of total polyphenols from curry leaves was investigated. The results showed that the temperature and solvent concentration have a great impact on extraction efficiency. The optimal batch extraction conditions found are temperature of 333 K and methanol-water concentration of 50% (v/v). Under these optimal conditions, the maximum concentration of total polyphenol content of 79.34 mgGAE/L was obtained. Mathematical modelling study showed that Peleg model fits the experimental data well. The positive correlation was found between all experimental and predicted values of total polyphenol concentration. The comparison of conventional Soxhlet and batch extraction methods with novel UAE method showed that less time and energy were required for UAE to get higher recovery of polyphenols than conventional methods.
AbbreviationsTPC:
Total polyphenol content
GAE/L:
Gallic acid equivalent/litre
UAE:
Ultrasound-assisted extraction
RMSE:
Root mean squared error
C(t):
Concentration of total polyphenols at time t
Ce:
Equilibrium concentration
CS:
Concentration of total polyphenols at saturation
k:
Rate constant of extraction
K1:
Peleg’s rate constant
K2:
Peleg’s capacity constant
n, B:
Model fitting parameters (Power law model)
t:
Time
R2:
Coefficient of correlation.
Data Availability
The results reported in the article are available from the corresponding author to other researchers upon request. Codes cannot be shared with other researchers.
Conflicts of Interest
The authors declare that they have no conflicts of interest.
StalikasC. D.Extraction, separation, and detection methods for phenolic acids and flavonoids200730183268329510.1002/jssc.2007002612-s2.0-37849002920Bucić-KojićA.PlaninićM.TomasS.BilićM.VelićD.Study of solid–liquid extraction kinetics of total polyphenols from grape seeds200781123624210.1016/j.jfoodeng.2006.10.0272-s2.0-33846582014PandeyK. B.RizviS. I.Plant polyphenols as dietary antioxidants in human health and disease20092527027810.4161/oxim.2.5.94982-s2.0-77953474824LazarL.TalmaciuA. I.VolfI.PopaV. I.Kinetic modeling of the ultrasound-assisted extraction of polyphenols from Picea abies bark20163219119710.1016/j.ultsonch.2016.03.0092-s2.0-84961583684WangL.WellerC. L.Recent advances in extraction of nutraceuticals from plants200617630031210.1016/j.tifs.2005.12.0042-s2.0-33646127620NingappaM. B.DineshaR.SrinivasL.Antioxidant and free radical scavenging activities of polyphenol-enriched curry leaf (Murraya koenigii L.) extracts2008106272072810.1016/j.foodchem.2007.06.0572-s2.0-34548252360SasidharanI.MenonA. N.Effects of temperature and solvent on antioxidant properties of curry leaf (Murraya koenigii L.)201148336637010.1007/s13197-010-0134-x2-s2.0-79960017192JainV.MominM.LaddhaK.Murraya koenigii: an updated review2012204607627RostagnoM. A.PradoJ. M.2013London, UKThe Royal Society of Chemistry, UK6465HerodežŠ.S.HadolinM.ŠkergetM.KnezŽ.Solvent extraction study of antioxidants from Balm (Melissa officinalis L.) leaves200380227528210.1016/S0308-8146(02)00382-52-s2.0-0037290913CacaceJ. E.MazzaG.Mass transfer process during extraction of phenolic compounds from milled berries200359437938910.1016/s0260-8774(02)00497-12-s2.0-0037680655PineloM.SineiroJ.NúñezM. J.Mass transfer during continuous solid-liquid extraction of antioxidants from grape byproducts2006771576310.1016/j.jfoodeng.2005.06.0212-s2.0-33747517635JokićS.VelićD.BilićM.Bucić-KojićA.PlaninićM.TomasS.Modelling of solid-liquid extraction process of total polyphenols from soybeans201028320621210.17221/200/2009-CJFSBaiao DiasA. L.Arroio SergioC. S.SantosP.BarberoG. F.RezendeC. A.MartinezJ.Ultrasound-assisted extraction of bioactive compounds from dedo de moca pepper (Capsicum baccatum L.): effects on the vegetable matrix and mathematical modeling20161983610.1016/j.jfoodeng.2016.11.0202-s2.0-84998772433WongkittipongR.PratL.DamronglerdS.GourdonC.Solid-liquid extraction of andrographolide from plants-experimental study, kinetic reaction and model200440214715410.1016/j.seppur.2004.02.0022-s2.0-11244289081Espinoza-PérezJ. D.VargasA.Robles-OlveraV. J.Rodrı´guez-JimenesG. C.Garcı´a-AlvaradoM. A.Mathematical modeling of caffeine kinetic during solid-liquid extraction of coffee beans2007811727810.1016/j.jfoodeng.2006.10.0112-s2.0-33846565005GujarJ. G.WaghS. J.GaikarV. G.Experimental and modeling studies on microwave-assisted extraction of thymol from seeds of Trachyspermum ammi (TA)201070325726410.1016/j.seppur.2009.08.0052-s2.0-72049118181PoojaryM. M.PassamontiP.Extraction of lycopene from tomato processing waste: kinetics and modelling201417394395010.1016/j.foodchem.2014.10.1272-s2.0-84911486042PatilD. M.AkamanchiK. G.Ultrasound-assisted rapid extraction and kinetic modelling of influential factors: extraction of camptothecin from Nothapodytes nimmoniana plant20173758259110.1016/j.ultsonch.2017.02.0152-s2.0-85013469474TušekA. J.BenkovićM.CvitanovićA. B.ValingerD.JurinaT.KljusurićJ. G.Kinetics and thermodynamics of the solid-liquid extraction process of total polyphenols, antioxidants and extraction yield from Asteraceae plants20169120521410.1016/j.indcrop.2016.07.0152-s2.0-84989886877PatilD. M.AkamanchiK. G.Microwave assisted process intensification and kinetic modelling: extraction of camptothecin from Nothapodytes nimmoniana plant201798606710.1016/j.indcrop.2017.01.0232-s2.0-85010188988DubaK. S.CasazzaA. A.MohamedH. B.PeregoP.FioriL.Extraction of polyphenols from grape skins and defatted grape seeds using subcritical water: experiments and modeling201594293810.1016/j.fbp.2015.01.0012-s2.0-84927537252SejaliS. N. F.AnuarM. S.Effect of drying methods on phenolic contents of neem (Azadirachta indica) leaf powder201117211913110.1080/10496475.2011.5842932-s2.0-79958783079GujarJ. G.ChattopadhyayS.WaghS. J.GaikarV. G.Experimental and modeling studies on extraction of catechin hydrate and epicatechin from Indian green tea leaves201088223224010.1002/cjce.202712-s2.0-77949990713PatilS. S.PathakA.RathodV. K.Optimization and kinetic study of ultrasound assisted deep eutectic solvent based extraction: a greener route for extraction of curcuminoids from Curcuma longa20217010526710.1016/j.ultsonch.2020.105267SingletonV. L.OrthoferR.Lamuela-RaventósR. M.Analysis of total phenols and other oxidation substrates and antioxidants by means of folin-ciocalteu reagent199929915217810.1016/s0076-6879(99)99017-12-s2.0-0031790242DongZ.GuF.XuF.WangQ.Comparison of four kinds of extraction techniques and kinetics of microwave-assisted extraction of vanillin from Vanilla planifolia Andrews2014149546110.1016/j.foodchem.2013.10.0522-s2.0-84887375572PelegM.An empirical model for the description of moisture sorption curves19885341216121710.1111/j.1365-2621.1988.tb13565.x2-s2.0-84985261051BelwalT.DhyaniP.BhattI. D.RawalR. S.PandeV.Optimization extraction conditions for improving phenolic content and antioxidant activity in Berberis asiatica fruits using response surface methodology (RSM)201620711512410.1016/j.foodchem.2016.03.0812-s2.0-84961876790BourasM.ChadniM.BarbaF. J.GrimiN.BalsO.VorobievE.Optimization of microwave-assisted extraction of polyphenols from Quercus bark20157759060110.1016/j.indcrop.2015.09.0182-s2.0-84942740759DahmouneF.NayakB.MoussiK.ReminiH.MadaniK.Optimization of microwave-assisted extraction of polyphenols from Myrtus communis L. leaves201516658559510.1016/j.foodchem.2014.06.0662-s2.0-84903978344JovanovićA. A.ĐorđevićV. B.ZdunićG. M.Optimization of the extraction process of polyphenols from Thymus serpyllum L. herb using maceration, heat-and ultrasound-assisted techniques201717936938010.1016/j.seppur.2017.01.0552-s2.0-85013059742CostaP.GonçalvesS.ValentãoP.AndradeP. B.CoelhoN.RomanoA.Thymus lotocephalus wild plants and in vitro cultures produce different profiles of phenolic compounds with antioxidant activity201213531253126010.1016/j.foodchem.2012.05.0722-s2.0-84865780572GoulaA. M.Ultrasound-assisted extraction of pomegranate seed oil - kinetic modeling2013117449249810.1016/j.jfoodeng.2012.10.0092-s2.0-84881632679GhitescuR.-E.VolfI.CarausuC.BühlmannA.-M.GilcaI. A.PopaV. I.Optimization of ultrasound-assisted extraction of polyphenols from Spruce wood bark20152253554110.1016/j.ultsonch.2014.07.0132-s2.0-84906786164WangJ.SunB.CaoY.TianY.LiX.Optimisation of ultrasound-assisted extraction of phenolic compounds from wheat bran2008106280481010.1016/j.foodchem.2007.06.0622-s2.0-34548263152