Journal of Chemistry

Volume 2013 (2013), Article ID 383985, 6 pages

http://dx.doi.org/10.1155/2013/383985

Research Article

Removal of Methylene Blue from Wastewater by Adsorption onto ZnCl₂ Activated Corn Husk Carbon Equilibrium Studies

Maryam Khodaie, Nahid Ghasemi, Babak Moradi, and Mohsen Rahimi

Department of Chemistry, Sciences Faculty, Islamic Azad University, Arak Branch, P.O. Box 38135-567, Arak, Iran

Received 29 June 2012; Accepted 30 January 2013

Academic Editor: Huu Hao Ngo

Copyright © 2013 Maryam Khodaie et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

The removal of methylene blue by activated carbon of corn husk by ZnCl₂ activation () was investigated in the present study. Adsorption studies were performed by batch experiments. The effect of pH, initial dye concentration, adsorbent dose, the particle size of , agitation speed, temperature, and contact time was explored. The equilibrium adsorption data were analyzed using two widely applied isotherms: Langmuir, Freundlich. Best fits were found to be Freundlich isotherm. Langmuir adsorption capacity () in 298, 308, and 318 K is 462.96, 546.45, and 662.25 mgg⁻¹. The amount of indicates that has a favorable adsorption. Maximum MB removal was observed at pH 4.0. The results indicate that is an efficient adsorbent for removing dye from wastewater.

1. Introduction

More than 10,000 dyes have been widely used in textile, paper, rubber, plastics, leather and cosmetic, pharmaceutical, and food industries [1]. The discharge of colored wastes into the receiving water bodies not only affects their aesthetic nature but also interferes with the transmission of sunlight and therefore reduces the photosynthetic activity [2]. As dyes are designed to resist breakdown with time, exposure to sunlight, water, soap, and oxidizing agent cannot be easily removed by conventional wastewater treatment processes due to their complex structure and synthetic origins [3]. Methylene blue (MB) is cationic dyes. MB will cause increased heart rate, vomiting, shock, Heinz body formation, cyanosis, jaundice, quadriplegia, and tissue necrosis in humans [4]. Various conventional methods such as physical, chemical, and biological processes have been tried for the removal of dyes from aquatic media [5–7]. Adsorption is one of the physical-chemical methods, which is found to be the most simple and economical to remove the dyes from effluents [8]. The adsorption attempts have been made to find alternative low-cost adsorbents [9]. Activated carbon prepared from these wastes helps to solve the waste disposal problem. Agricultural wastes include orange peel [10], jute fiber [11], wheat shells [12], soy meal hull [13], rice husk [14], activated date pit [15], and bamboo dust [16]. Most of the activated carbons are produced by a two-stage process carbonization followed by activation. The first step is to enrich the carbon content and to create an initial porosity and the activation process helps in enhancing the pore structure. Basically, the activations are two different processes for the preparation of activated carbon: physical activation and chemical activation. Among the numerous dehydrating agents, zinc chloride in particular is the widely used chemical agent in the preparation of activated carbon. Knowledge of different variables during the activation process is very important in developing the porosity of carbon sought for a given application. Chemical activation by zinc chloride improves the pore development in the carbon structure, and because of the effect of chemicals, the yields of carbon are usually high [17, 18]. In the present study, activated carbons prepared from husk corn have been used as an adsorbent for dye removal of MB. The effects of operating parameters such as initial dye concentration, adsorbent dosage, pH, agitation speed, contact time, particle size, and temperature were studied.

2. Materials and Methods

The raw material, husk corn, was repeatedly washed with distilled water to remove dirt, dust, and other impurities. The husk corn was dried 24 hours in oven with 383 K and then crushed and garbled. This material was impregnated with concentrated solution of husk corn powder to ZnCl₂with ratio 1 : 1 in the mixed system and then dried in the oven at 383 K. The activation of the samples was performed in the furnace at 723 K for 5 h, washed thoroughly with distilled water until it attained the neutral pH, and soaked in KOH solution overnight in order to remove any excess alkali present. The material was then washed with distilled water until it reached neutral pH and dried at 723 K. A stock solution () of MB was prepared by dissolving an appropriate amount of each dye in double distilled water, which was diluted to desired batch adsorption experiments that were carried out to investigate the effect of pH, adsorbent dose, initial dye concentration, contact time, particle size, agitation speed, and temperature on the adsorption of MB. The experiments were carried out in 100 mL conical flasks by mixing a preweighed amount of adsorbent with 50 mL of dye solution and the solution was agitated at 150 rpm on a stirrer at constant temperature, and after shaking the solution, the reaction mixtures were centrifuged and the filtrate was analyzed using spectrophotometer. The adsorption isotherm experiment was carried out in a thermostatic orbital shaker at a constant speed of 150 rpm at different temperatures (298, 308, and 318 K) by adding agitating 50 mL of dye solution of various concentrations. After agitation, the dye solutions were separated from the adsorbent by centrifugation for 10 min. The dye removal was determined by a spectrophotometer using 665 nm as the maximum absorbance wavelength. The percentage removal of dye and the amount of dye adsorbed on adsorbent () were calculated, respectively, as follows:

where is the amount of dye adsorbed on adsorbent at equilibrium (), and are the initial and equilibrium of dye concentration () in solution, respectively, is the volume of solution , and is the weight of adsorbent .

3. Results and Discussion

3.1. Effect of pH

The pH of the dye solution plays an important role in the whole adsorption process, particularly on adsorption capacity [19]. Figure 1 shows the effect of pH on the adsorption of MB onto the CHACZ at initial concentration of 50  MB and the amount of adsorbent ) at 150 rpm agitation speed and at 298 K. If the pH of the dye solution was changed from 3 to 11, the adsorption capacity of CHACZ was raised from 120.08 to . In the process of adsorption, at a lower pH, the adsorbent surface is positively charged, favoring adsorption of anionic contaminants. Because MB is a cationic dye, positive charge which occupied the feasible adsorption position competes with dye molecules, resulting in a lower adsorption of dyes; while at a higher pH, negatively charged surface facilitates adsorption of cationic contaminants [20].

Figure 1: Effect of pH (, adsorbent , ,  ,  ).

3.2. Effect of Adsorbent Dose

This effect was studied using a dose of CHACZ from 0.1 to that was shown in Figure 2. The results show that the percentage of adsorption was increased by increasing the dose of CHACZ until . It is apparent that by increasing the dose of the CHACZ, the number of sorption sites available for sorbent-biosolute interaction is increased, thereby resulting in the increased percentage of MB removal from the solution. The decrease in sorbent capacity, that is, the amount of MB sorbed per unit weight of sorbent with increase in CHACZ dose, may be attributed to two reasons. The increase in sorbent dose at constant MB concentration and volume will lead to unsaturation of sorption sites through the sorption process and secondly may be due to particulate interaction such as aggregation resulting from high sorbent dose. Such aggregation would lead to a decrease in total surface area of the sorbent and an increase in diffusional path length [21].

Figure 2: Effect of adsorbent dose (,  , ,  , ).

3.3. Effect of Initial MB Concentration

The effect of initial MB concentration (between 40 and ) on the adsorption of MB onto the CHACZ was studied. The adsorption capacity of CHACZ increased with increasing initial MB concentration and percent adsorption decreased with the increase in initial MB concentration, just as also shown in Figure 3. It means that the adsorption is highly dependent on initial concentration of MB. It is because of that, at lower concentration, the ratio of the initial number of MB molecules to the available surface area is low and subsequently the fractional adsorption become independent of initial concentration. However, at high concentration the available sites of adsorption becomes fewer and hence the percentage removal of MB is dependent upon initial concentration.

Figure 3: Effect of initial MB concentration (, adsorbent , , , ).

3.4. Effect of Contact Time

Contact time is also an important factor affecting removal; most of adsorption occurs in the initial half hour and increases very slowly later. These experiments have been carried out at variation of time of contact (0–120 minutes). Figure 4 shows that adsorption of MB onto the CHACZ reached to the equilibrium in 80 minutes. It was reported that during adsorption of dyes, initially the MB molecules reach the boundary layer; then they have to diffuse into the adsorbent surface; and finally, they have to diffuse into the porous structure of the adsorbent. Therefore, this phenomenon will take a relatively longer contact time [22].

Figure 4: Effect of contact time (, adsorbent , , ,   ).

3.5. Effect of Agitation Speed

Agitation is an important parameter in adsorption phenomena influencing the distribution of the solute in the bulk solution and formation of the external boundary film. The effect of biosorption of MB onto CHACZ was studied at different agitation speeds. The result is shown in Figure 5. It was observed that the adsorbed MB by CHACZ increased with the increase in agitation speed. By further increasing the speed, there was a further increase in biosorption because all binding sites were available for further biosorption. With agitation, the external mass transfer coefficient increases resulting in quicker adsorption of the MB.

Figure 5: Effect of agitation speed (, adsorbent , , , ).

3.6. Effect of Particle Size

The effect of variation in particle size CHACZ for an initial MB concentration of is shown in Figure 6. The experiments were carried out using CHACZ with several particle sizes (125–279 μm). The results also showed that biosorption increases with an increase in particle size of biosorbents. The relatively higher adsorption with smaller adsorbent particle may be attributed to the fact that smaller particles yield large surface areas. The particle size decreases and surface area exposed to biosorption of MB increases as particle size increases. This may be due to an increase in the accessibility of the adsorbate to the pores of the biosorbents with the decrease in particle size. With biosorption being a surface phenomenon, the smaller biosorbent particle size offers comparatively larger surface area and higher biosorption occurs at equilibrium [23].

Figure 6: Effect of particle sizes (, adsorbent , , ,  , ).

3.7. Effect of Temperature

This effect was investigated at (298–338 K). Figure 7 shows the adsorption capacity of CHACZ increased from 164.13 to , when the temperature was increased from 298 to 328 K. Increasing the temperature is known to increase the rate of diffusion of the adsorbate molecules across the external boundary layer and in the internal pores of the adsorbent particle, owing to the decrease in the viscosity of the solution. In addition, changing temperature will change the equilibrium capacity of the adsorbent for a particular adsorbate [24].

Figure 7: Effect of temperature (, adsorbent , , ,  ).

3.8. Isotherm Studies

Equilibrium uptake of MB was investigated at 297 K with sorbent weight of 0.015 g of CHACZ in contact with 50 mL of MB solutions and at pH 4.00. The flasks were shaken at 150 rpm and the equilibrium concentration of the remaining MB was determined spectrophotometrically. The equilibrium adsorption isotherm is of importance in the design of adsorption systems [25]. In general, the adsorption isotherm describes how adsorbents interact with adsorbents and thus is critical in optimizing the use of adsorbents. Several isotherm equations are available, and two important isotherms were selected for this study: the Langmuir and Freundlich isotherms. The Langmuir adsorption isotherm assumes that adsorption takes place at specific homogeneous sites within the adsorbent, and it has been used successfully for many adsorption processes of monolayer adsorption [25].

The linearized Langmuir equation is represented as follows [26]:

where is the equilibrium constant or Langmuir constant related to the affinity of binding sites (Lmg⁻¹) or (Lmol⁻¹) and represents a partial limiting adsorption capacity when the surface is fully covered with MB molecules which assists in the comparison of adsorption performance. and were calculated from the slope and interception of the straight lines of the plot versus [27]. The Langmuir maximum adsorption capacity () is 462.96, 546.45, and 662.25 mgg⁻¹ at 298, 308, and 318 K, respectively.

Essential characteristics of the Langmuir isotherms can be described by a separation factor which is defined by the following equation [28]:

where is the initial concentration of MB and is the Langmuir adsorption constant . The value of separation factor indicates the nature of the absorption process [21]. In the absorption of MB onto CHACZ, values were in the range of 0.063–0.080; this result shows that the absorption of MB onto CHACZ is favorable. In Figure 8 the seen values of absorption of MB onto CHACZ decrease with increasing the temperature.

Figure 8: Comparison of absorption of MB onto CHACZ in three temperatures.

The Freundlich isotherm is an empirical equation used to describe heterogeneous systems [26]. The Freundlich isotherm is given in logarithmic form as follows:

where and are roughly an indication of the adsorption capacity of adsorbent and the adsorption intensity, respectively. and () can be determined from the linear plot of log versus log [25]. is a Freundlich constant that shows the strength of the relationship between adsorbate and adsorbent, and the values of CHACZ for MB adsorption are 114.55, 135.21, and 125.89 at 298, 308, and 318 K, respectively. The value of Freundlich equation could give an indication on the favorability of sorption. It is generally stated that the values of in the range of 1 to 10 represent good adsorption [27]. The values of CHACZ for MB adsorption were obtained between 1 and 10,and therefore this adsorption is favorable.

Figures 9, 10, and 11 show the plots comparing the Langmuir and Freundlich isotherms with the experimental data for the adsorption of MB onto CHACZ at a pH of 4. The parameters and correlation coefficients obtained from the plots of Langmuir and Freundlich isotherms are listed in Table 1. By comparing the correlation coefficients obtained from the two isotherm models, the Freundlich isotherm gave the best correlation for the sorption process and adsorption of MB by the CHACZ followed the Freundlich isotherm.

Table 1: Langmuir and Freundlich constants for the adsorption of MB onto CHACZ.

K
Langmuir
Freundlich

mg 

L 

L 

298
462.96
0.087
0.995
0.080
114.55
3.47
0.996

308
546.45
0.097
0.958
0.072
135.21
3.41
0991

318
662.25
0.103
0.962
0.063
125.89
2.58
0.997

Figure 9: The Langmuir and Freundlich isotherms for the adsorption of MB onto CHACZ (adsorbent dose: ; pH: 4; temperature: ).

Figure 10: The Langmuir and Freundlich isotherms for the adsorption of MB onto CHACZ (adsorbent dose: ; pH: 4; temperature: ).

Figure 11: The Langmuir and Freundlich isotherms for the adsorption of MB onto CHACZ (adsorbent dose: ; pH: 4; temperature: ).

4. Conclusion

(i)CHACZ can be used as an efficient and cheap absorbent for refining wastewater.(ii)The amount of MB removed by CHACZ increases with increasing these parameters: SFACH dose, pH, contact time, agitation speed (rpm), and temperature, and thus, removal was increased by decreasing CHACZ particle size, and initial MB concentration.(iii)Adsorption behavior of the CHACZ is described by Freundlich isotherm.(iv)The amount of showed that CHACZ can be used for dye removal.(v)Adsorption behavior is multilayer Freundlich type isotherms for the activated carbons.(vi)The result indicates that ; therefore this adsorption process is physical.

References

S. Mondal, “Methods of dye removal from dye house effluent—an overview,” Environmental Engineering Science, vol. 25, no. 3, pp. 383–396, 2008.

K. Rastogi, J. N. Sahu, B. C. Meikap, and M. N. Biswas, “Removal of methylene blue from wastewater using fly ash as an adsorbent by hydrocyclone,” Journal of Hazardous Materials, vol. 158, no. 2-3, pp. 531–540, 2008.

L. Wang, J. Zhang, and A. Wang, “Removal of methylene blue from aqueous solution using chitosan-g-poly(acrylic acid)/montmorillonite superadsorbent nanocomposite,” Colloids and Surfaces A, vol. 322, no. 1–3, pp. 47–53, 2008.

R. Ahmad and R. Kumar, “Adsorption studies of hazardous malachite green onto treated ginger waste,” Journal of Environmental Management, vol. 91, no. 4, pp. 1032–1038, 2010.

N. Barka, S. Qourzal, A. Assabbane, A. Nounah, and Y. Ait-Ichou, “Photocatalytic degradation of an azo reactive dye, Reactive Yellow 84, in water using an industrial titanium dioxide coated media,” Arabian Journal of Chemistry, vol. 3, no. 4, pp. 279–283, 2010.

M. F. Elahmadi, N. Bensalah, and A. Gadri, “Treatment of aqueous wastes contaminated with Congo Red dye by electrochemical oxidation and ozonation processes,” Journal of Hazardous Materials, vol. 168, no. 2-3, pp. 1163–1169, 2009.

M. Khadhraoui, H. Trabelsi, M. Ksibi, S. Bouguerra, and B. Elleuch, “Discoloration and detoxicification of a Congo red dye solution by means of ozone treatment for a possible water reuse,” Journal of Hazardous Materials, vol. 161, no. 2-3, pp. 974–981, 2009.

A. R. Tehrani-Bagha, H. Nikkar, N. M. Mahmoodi, M. Markazi, and F. M. Menger, “The sorption of cationic dyes onto kaolin: kinetic, isotherm and thermodynamic studies,” Desalination, vol. 266, no. 1–3, pp. 274–280, 2011.

G. Crini, “Non-conventional low-cost adsorbents for dye removal: a review,” Bioresource Technology, vol. 97, no. 9, pp. 1061–1085, 2006.

R. Sivaraj, C. Namasivayam, and K. Kadirvelu, “Orange peel as an adsorbent in the removal of acid violet 17 (acid dye) from aqueous solutions,” Waste Management, vol. 21, no. 1, pp. 105–110, 2001.

S. Senthilkumaar, P. R. Varadarajan, K. Porkodi, and C. V. Subbhuraam, “Adsorption of methylene blue onto jute fiber carbon: kinetics and equilibrium studies,” Journal of Colloid and Interface Science, vol. 284, no. 1, pp. 78–82, 2005.

Y. Bulut and H. Aydin, “A kinetics and thermodynamics study of methylene blue adsorption on wheat shells,” Desalination, vol. 194, no. 1–3, pp. 259–267, 2006.

M. Arami, N. Y. Limaee, N. M. Mahmoodi, and N. S. Tabrizi, “Equilibrium and kinetics for the adsorption of direct acid dyes from aquous solution by soy meal hull,” Journal of Hazardous Materials, vol. 135, no. 1–3, pp. 171–179, 2006.

P. K. Malik, “Use of activated carbons prepared from sawdust and rice-husk for adsoprtion of acid dyes: a case study of acid yellow 36,” Dyes and Pigments, vol. 56, no. 3, pp. 239–249, 2003.

F. Banat, S. Al-Asheh, and L. Al-Makhadmeh, “Evaluation of the use of raw and activated date pits as potential adsorbents for dye containing waters,” Process Biochemistry, vol. 39, no. 2, pp. 193–202, 2003.

N. Kannan and M. M. Sundaram, “Kinetics and mechanism of removal of methylene blue by adsorption on various carbons—a comparative study,” Dyes and Pigments, vol. 51, no. 1, pp. 25–40, 2001.

J. Acharya, J. N. Sahu, C. R. Mohanty, and B. C. Meikap, “Removal of lead(II) from wastewater by activated carbon developed from Tamarind wood by zinc chloride activation,” Chemical Engineering Journal, vol. 149, no. 1–3, pp. 249–262, 2009.

J. Acharya, J. N. Sahu, B. K. Sahoo, C. R. Mohanty, and B. C. Meikap, “Removal of chromium(VI) from wastewater by activated carbon developed from Tamarind wood activated with zinc chloride,” Chemical Engineering Journal, vol. 150, no. 1, pp. 25–39, 2009.

S. Wang, Y. Boyjoo, and A. Choueib, “A comparative study of dye removal using fly ash treated by different methods,” Chemosphere, vol. 60, no. 10, pp. 1401–1407, 2005.

G. Zhang and Y. Bao, “Study of adsorption characteristics of methylene blue onto activated carbon made by salix psammophila,” Energy Procedia, vol. 16, pp. 1141–1146, 2011.

E. N. El Qada, S. J. Allen, and G. M. Walker, “Adsorption of basic dyes onto activated carbon using microcolumns,” Industrial & Engineering Chemistry Research, vol. 45, no. 17, pp. 6044–6049, 2006.

S. Senthilkumaar, P. R. Varadarajan, K. Porkodi, and C. V. Subbhuraam, “Adsorption of methylene blue onto jute fiber carbon: kinetics and equilibrium studies,” Journal of Colloid and Interface Science, vol. 284, no. 1, pp. 78–82, 2005.

A. G. Liew Abdullah, A. G. Mohd Salleh, M. A. Siti Mazlina et al., “Azo dye removal by adsorption using waste biomass: sugarcane bagasse,” International Journal of Engineering and Technology, vol. 2, no. 1, pp. 8–13, 2005.

Z. Al-Qodah, “Adsorption of dyes using shale oil ash,” Water Research, vol. 34, no. 17, pp. 4295–4303, 2000.

Y. Bulut and H. Aydin, “A kinetics and thermodynamics study of methylene blue adsorption on wheat shells,” Desalination, vol. 194, no. 1–3, pp. 259–267, 2006.

V. Vadivelan and K. V. Kumar, “Equilibrium, kinetics, mechanism, and process design for the sorption of methylene blue onto rice husk,” Journal of Colloid and Interface Science, vol. 286, no. 1, pp. 90–100, 2005.

Y. H. Magdy and A. A. M. Daifullah, “Adsorption of a basic dye from aqueous solutions onto sugar-industry-mud in two modes of operations,” Waste Management, vol. 18, no. 4, pp. 219–226, 1998.

T. W. Weber and P. K. Chakravorti, “Pore and solid diffusion models for fixed bed adsorbent,” AIChE Journal, vol. 20, no. 2, pp. 228–238, 1974.