Cost of biodiesel produced from virgin vegetable oil through transesterification is higher than that of fossil fuel, because of high raw material cost. To minimize the biofuel cost, in recent days waste cooking oil was used as feedstock. Catalysts used in this process are usually acids, base, and lipase. Since lipase catalysts are much expensive, the usage of lipase in biodiesel production is limited. In most cases, NaOH is used as alkaline catalyst, because of its low cost and higher reaction rate. In the case of waste cooking oil containing high percentage of free fatty acid, alkaline catalyst reacts with free fatty acid and forms soap by saponification reaction. Also, it reduces the biodiesel conversions. In order to reduce the level of fatty acid content, waste cooking oil is pretreated with acid catalyst to undergo esterification reaction, which also requires high operating conditions. In this review paper, various parameters influencing the process of biofuel production such as reaction rate, catalyst concentration, temperature, stirrer speed, catalyst type, alcohol used, alcohol to oil ratio, free fatty acid content, and water content have been summarized.
1. Introduction
Fuels, generated from biological feed stocks, are termed as “biofuels.” In general, biofuels can be broadly classified into first-generation fuels and second-generation fuels. First generation fuels or conventional biofuels are generally derived from sugar, starch, and vegetable oil source. Whereas, second-generation biofuels are generated from sustainable feedstocks. The major classification of biofuels is shown in Figure 1.
Classification of biofuels.
Because of high viscous nature, direct application of vegetable oil as a fuel in compression ignition engines has been limited [1]. It is possible to reduce its viscosity by converting vegetable oil into alkyl esters using transesterification reaction [2–4]. Nowadays, biodiesel production has been increased enormously to compete with fossil fuels. The production of biodiesel in recent years around the world is shown in Figure 2. Biofuels are mostly derived from edible oil, nonedible oil, fats, waste cooking oil, and algae. Advantage of using virgin vegetable oil (edible oil) as raw material for production of biodiesel is their low free fatty acid content [5]. Similarly, the main advantage of biodiesel synthesis over nonedible oil source is due to their high free fatty acid content [6].
Production of biodiesel in recent years [7].
Instead of using virgin vegetable oil, waste cooking oil can be used as raw material for biodiesel production [8]. In most of hotels, restaurants, and in other food industries, the waste cooking oil is either simply discharged into the river or dumped into the land. Inspite of this, the waste cooking oil can be used effectively for the biodiesel synthesis. Biodiesel production from waste cooking oil is found to be economically feasible method [9]. Different sources of raw material used for the production of biodiesel are shown in Figure 3. The property of biodiesel depends on the type of fresh cooking oil used [10]. Biodiesel can also be blended with mineral oil [11]. Even the wastes (byproducts) generated from biodiesel production can be used for power production [12].
Production of biodiesel from different feed stock [13].
2. Basic Reaction Mechanism Involved in the Production of Biodiesel2.1. Transesterification
The major component of vegetable oil is triglycerides. When the triglycerides react with alcohol in the presence of base catalyst, this is called “transesterification.” In this reaction, triglycerides are converted to diglyceride, monoglyceride, and finally converted to glycerol. The reaction mechanism is shown in Scheme 1.
2.2. Side Reaction 1 (Saponification Reaction)
If vegetable oil contains free fatty acid, it will react with homogenous base catalyst to form soap and water. The saponification reaction is represented as shown in Scheme 2.
The main drawback in this reaction is the consumption of catalyst and increased difficulty in separation process, which leads to high production cost. In addition to that, formation of water in the product will also inhibit the reaction.
2.3. Side Reaction 2 (Hydrolysis Reaction)
Water generated either from vegetable oil or formed during saponification reaction will hydrolyze triglyceride to form more free fatty acid. The hydrolysis reaction is given as shown in Scheme 3.
Various methods of biodiesel production through transesterification of waste cooking oil are shown in Table 1.
Various methods used for production of biodiesel from waste cooking oil through transesterification.
(1) Less corrosive(2) Less toxicity(3) Less environmental problem
(1) Low acid concentration(2) High cost (3) Diffusion limitation
[10, 17, 27, 31]
Enzyme
Candida antarctica fraction B lipase, Rhizomucor mieher lipase, E. aerogenes lipase, lipase immobilized on hydrotalcite and zeolites
(1) By product of process can be easily removed(2) Free fatty acid can be completely converted into methyl esters, regeneration and reuse of immobilized enzyme catalyst are possible
(1) High reaction time required (2) Expansive, activity loss, agglomeration of enzyme
[10, 16, 20, 21, 32–38]
2.4. Esterification
In order to eliminate saponification reaction (formation of soap when FFA reacts with homogenous base catalyst) vegetable oil can be pretreated with acid catalyst, which esterifies free fatty acid to form esters of free fatty acid (biodiesel). This reaction is very much useful when raw material contains high percentage of free fatty acid (esterification of free fatty acid to form free acid esters). But this reaction is slower than base catalyzed transesterification reaction. The esterification reaction is given as shown in Scheme 4.
3. Factors Affecting the Production of Biodiesel from Waste Cooking Oil3.1. Water Content
Water content in waste cooking oil will accelerate the hydrolysis reaction and simultaneously reduce the amount of ester formation [20]. Water content should not always exceed 0.5% to obtain 90% yield of biodiesel and it is more critical for an acid-catalyzed reaction than base-catalyzed reaction [49]. When acid catalysts are used for esterification of free fatty acid to form esters, water is obtained as by-product. Water will naturally inhibit acid-catalyzed reaction [8] and also its presence in the product will decrease the efficiency of engines. In most cases waste cooking oil is preheated to 120°C to evaporate water molecules [50] and those water molecules present in the product can be removed by using anhydrous sodium sulfate (Na2SO4) [51] or magnesium sulfate anhydrous [15]. Some enzymes require certain amount of water to be active, which is lesser than monolayer amount of water molecules around the enzyme molecules [52]; if water present in raw material exceeds this limit, it will decrease the conversion by deactivating the lipase [33].
3.2. Free Fatty Acid
Waste cooking oil contains high free fatty acid content than the fresh cooking oils [44]. Hence, it is know that higher free fatty acid contents will lead to formation of soap and water. Similarly, if free fatty acid content exceeds 3%, transesterification reaction will not proceed even with homogenous base catalyst [51]. Hence this problem could be solved by using heterogeneous catalyst [12, 27, 53] and also on pretreatment with acid homogenous catalyst [18, 54–56] or heterogeneous catalyst [11, 17, 57–59] to esterify the free fatty acid to form free fatty acid ester. Usually, the acid-catalyzed reaction rate is low and high reaction conditions are required [10]. Soaps formed while neutralizing free fatty acid using homogenous base catalyst can be converted back to free fatty acid by adding phosphoric acid to decanted glycerol and soap mixture obtained from final product [6].
3.3. Type of Alcohol
In most cases, methanol is used for the production of biodiesel, because recovery of methanol from the final product is much easier [58]. Yield of biodiesel obtained from waste cooking oil using methanol is higher than other alcohols (ethanol, butanol) [45, 46] and viscosity of biodiesel obtained using methanol is lesser than that of biofuel obtained from other alcohols [46]. The cost of methanol is lesser than that of other alcohols, but ethanol is less toxic than methanol [21]. Ethanol can be obtained from renewable source [39]. When ethanol or isopropanol is used it will form azeotrope with water, which inturn makes difficulty in separation of water from alcohol during distillation process [55]. In some cases, i-butanol or t-butanol is added as solvent to the reaction mixture to avoid the inhibition of lipase by methanol or glycerol. But in most of enzymatic reactions, ethanol is being used instead of methanol [33, 60].
3.4. Alcohol to Oil Ratio
To produce three moles of alkyl esters, three moles of alcohol and one mole of triglyceride are required [19]. Alcohol to oil ratio always has positive, effect on biofuel conversion [61]. According to Le Chateliers principle, the rate of formation of product increases as reactant concentration is increased. Therefore, if the concentration of alcohol is increased automatically, the rate of product formation will be accelerated. Further increase in the molar ratio of alcohol to oil will increase the product formation. The recovery of glycerol and unreacted methanol becomes tedious [21, 56] and also increases the cost of product biodiesel by increasing its posttreatment cost. Hossain et al. [46] used methanol for transesterification of waste sunflower oil and studied using various molar ratio of alcohol to oil with NaOH catalyst and found that 6 : 1 molar ratios of alcohol to oil gave the highest yield of 99.5% methyl ester [15]. But when they studied the transesterification of waste canola oil using 1 : 1 molar ratio of methanol to oil, the yield was reported to be 49.5% [46].
3.5. Catalyst Type
In recent years, various catalysts (homogenous, heterogeneous, and enzyme catalyst) had been tested for the production of alkyl esters. Vicente et al. [14] studied using various base catalysts for production of alkyl esters and concluded that NaOH is the fastest catalysts among the catalysts used (NaOH, KOH, sodium methoxide, the potassium methoxide). Refaat et al. [43] reported that KOH gives the highest yield for feedstock he had used. Some of the researchers used concentrated sulfuric acid as acid catalyst [62, 63], but it requires high reaction time and high reaction condition. Even 1% (mole) can give up to 99% conversion [21]. In the case of raw material having higher free fatty acid content, acid catalyst (homogenous/heterogeneous) are used for esterification reaction [19]. Acid catalyst can be used simultaneously for both esterification and transesterification reactions [49]. One of the main disadvantages in using homogenous catalyst is the recovery of catalyst from the final product and formation of soap [14]. To overcome this issue most of researchers used heterogeneous catalyst because heterogeneous catalyst is not affected by free fatty acid and moisture present in the raw material [64]. Enzyme catalytic reaction is the slowest reaction among all other catalytic reactions. They can be used for both esterification and transesterification processes. Though the separation of product is easier while using enzyme catalyst, preparation of enzyme catalyst is most critical [21, 52].
3.6. Catalyst Concentration
In the absence of catalyst, conversion of waste cooking oil into biofuel requires high temperature conditions [65]. When catalyst concentration is increased, the yield of the product will also increase. This is due to enhancement in rate of reaction. However, the conversion decreases with excess catalyst concentration, which may be due to increased viscosity of the reaction mixture [66]. Many researchers studied by varying the catalyst concentration and also optimized the concentration of catalyst based on product yield and catalyst recovery. Chen et al. [59] used CuVOP and reported that 1.5% of catalyst concentration is most effective for the production of biodiesel from soya bean oil. Increase of enzyme concentration will increase the percentage conversion. But beyond the certain limit, agglomeration of enzyme will take place. It will decrease the active site available on substrate [33, 34]. Dehkordi and Ghasem [67] studied with heterogeneous solid catalysts comprising CaO- and ZrO2-mixed oxides, with different molar ratios of Ca and Zr. It was reported that by increasing Ca/Zr ratio, biodiesel yield was increased. But the stability of catalyst was decreased [67]. Hence the optimum catalyst concentration would vary depending upon the type of raw material and catalyst [19].
3.7. Stirrer Speed
The mixing of reactants is very important to achieve completion of transesterification reaction and also it increases the yield of product [68]. Agitation increases the collision between the particles and diffusion of one reactant into another, thorough mixing of catalyst with reactants and rate of reaction. Increase in stirrer speed will shorten the reaction time [53] and increase the conversion [69]. Beyond certain speed of stirrer, there would not be significant rise in the yield. Therefore, optimization of stirrer speed is necessary for different raw materials based on the different physical properties. Using enzyme catalyst or heterogeneous porous catalyst, the reactants have to diffuse from bulk liquid to surface of catalyst and further into interior surface of catalyst. Kumari et al. [33] found out that there is increase in conversion by increasing the stirrer speed from 100 to 200 rpm. But at 250 rpm, there was no significant increase in the conversion because of shearing in the enzyme molecules. Hence, it was suggested that 200 rpm was the optimum speed for production of biodiesel using enzymatic reaction.
3.8. Temperature
Temperature has significant influence on transesterification reaction [72]. If the reaction temperature is increased, then the rate of reaction and yield of product will also tend to increase [19, 53]. The temperature should not exceed the boiling point of alcohol. This will avoid vaporization of alcohol [64]. But if the reaction temperature is maintained below 50°C, then the viscosity of biodiesel will increase [73]. In some cases, waste cooking oil is preheated to 120°C to remove water particles present in the raw material and then cooled to 60°C [74]. For an enzymatic reaction, conversion increases over a temperature range of 30–55°C. In case of lipase as catalyst, Jatropha oil reported maximum conversion at 55°C [33] and for cotton seed oil maximum conversion was obtained at 50°C [46, 60]. Freedman et al. [62] found that there was no difference in conversion for temperatures 45°C and 60°C. But at 32°C, conversion was much lower than conversion obtained at 45°C and 60°C. After 4 hours, conversion at 32°C was slightly higher than conversion obtained at other temperatures [63]. Refaat et al. [43] studied fresh and waste cooking oil from both domestic and commercial sources and reported highest yield at 65°C for all the feed stocks using KOH catalyst. Chen et al. [75] found that the reaction time was reduced significantly to get maximum yield of biodiesel by using of microwave heating.
3.9. Reaction Time
When the reaction was carried out for a longer time, even 99% of yield could be obtained, but it depends on the availability of reactants in the reaction mixture. If the reaction parameters are not properly adjusted, there are possibilities for the backward reaction, which will decrease the yield of product [45, 76]. For lipase-catalyzed reaction, time required varies over a range of 7–48 hours [60]. Kapilakarn and Peugtong [73] found that reaction time also affects the product cost. Al-Widyan and Al-Shyoukh [39] reported that when the reaction time increases, specific gravity of the product decreases in an exponential manner and ends with an asymptotic value with respect to time. Refaat et al. [43] obtained a yield of 96.10% for 1 h duration and for reaction time > 1 h < 3 h, it was reported that there was no significant increase in biodiesel yield (96.350%). Hence, reaction time should be optimized to reduce the production cost.
3.10. pH
pH is not a major factor, when base/acid catalyst are used in the reaction. When lipase was used as catalyst, pH needs to be considered, because at lower or higher pH value, enzymes may decompose. Devanesan et al. [38] studied biodiesel production from Jatropha oil using immobilized Pseudomonas fluorescence and studied the effect of pH and concluded that pH value of 7 is optimum for production for biodiesel.
4. Process Description
If the acid value of waste cooking oil exceeds 1-2 mg KOH/mg of feed stock [8, 17, 18, 54], then pretreatment of waste cooking oil is required before it gets reacted with alkaline base catalyst.
4.1. Process I
Waste cooking oil may contain particulate matter and other impurities. Such impurities are removed by allowing the waste cooking oil through the filter. Feed stock oils are usually preheated to 60°C by heat exchangers.
Alcohol and acid catalysts are properly mixed in mixer before they were allowed into the esterification reactor. The mixing temperature is usually maintained at 60°C [68]. Catalyst mixture and preheated feedstock are allowed into the esterification reactor. Esterification reaction was carried out between 80 and 90°C and at 1 atmospheric pressure. Products from esterification reactor were cooled to 45°C, and catalyses are removed or neutralized before allowing into the settling tank to remove the methanol and water mixture. From the top of the settling tank, methanol and water mixture is removed and taken to distillation column to separate methanol from methanol water mixture and methanol is reused. The bottom product of separating vessel is taken to process II for transesterification reaction. Schematic representation of the process I is shown in Figure 4.
Pretreatment of high free fatty acid feed-stock with acid-catalyzed reactor—process I [70, 71].
4.2. Process II
Catalyst and alcohol are mixed in the mixer and products obtained from process I are taken into the transesterification reaction column along with catalyst and alcohol mixture. Reactor temperature is usually maintained at 65°C, 1 atmospheric pressure, and 1 : 6 molar ratio of oil to alcohol. Products of transesterification reactor are feed into separator 2. From the separation tank, biodiesel and alcohol mixture is distilled to separate methanol and biodiesel. Methanol from distillation column is recycled and reused. Biodiesel is washed with hot water and sent to separator to remove water and biodiesel. From the third separator tank, biodiesel is sent to storage tank. Bottoms of second separator section are moved to the alcohol and glycerol distillation column. From the top of distillation column methanol is recycled. Bottom product of distillation column is taken as byproduct. Schematic representation of the process II is shown in Figure 5.
Alkali-catalyzed treatment of pretreated waste cooking oil—process II [70, 71].
The recent research works on various waste cooking oils under different operating parameters as shown in Table 2.
Recent research on waste cooking oil and operating parameters.
Oil types
Type of alcohol
Process method
Parameters
Catalyst type
References
T°C
C (catalyst percentage)
M (alcohol to oil ratio and wt%)
Speed (rpm)
Time
A (acid catalyst)%
B (base catalyst)%
Palm oil
Ethanol
Acid-catalyzed transesterification
90°C
0.5, 1.0, 1.5, and 2.25 wt%
—
25, 50, and 100%
—
—
HCL, H2SO4
Al-Widyan and Al-Shyoukh (2002) [39]
Waste frying oil
Methanol
Alkali-catalyzed transesterification
65°C
—
5.3% of the KOH/MeOH solution
5.3% of the KOH/MeOH solution
—
90 min
KOH
Cvengroš and Cvengrošová (2004) [40]
Waste frying oil
Methanol
Base-catalyzed transesterification
65°C
—
Between 0.2% and 1.0%
3.6–5.4
—
1 h
NaOH
Felizardo et al. (2006) [41]
Waste cooking-oil collected from restaurant
Two-step catalyzed process
95°C & 65°C
0, 1, 2, 3, and 4 wt%
1%
3, 5, 7, 8, and 10 : 1, and 6 : 1
—
0.25 h, 0.5, 1, 2, 3 h, and 4 h
Ferric sulfate, KOH
Wang et al. (2007) [42]
Sunflower oil
Methanol
Base-catalyzed transesterification
25°C & 65°C
—
0.5 and 1.0%
3 : 1, 6 : 1, and 9 : 1
—
1–3 h
KOH, NaOH
Refaat et al. (2008) [43]
Canola oil
Ethanol
Base-catalyzed transesterification
60°C
—
0.2, 0.4, 0.6, 0.8, 1.0, and 1.2%
—
—
25 min
NaOH
Refaat et al. (2008) [44]
Sunflower oil
Base-catalyzed transesterification
40°C
—
0.5–2.0%
1 : 4.1 : 3, 3 : 1, 4 : 1, 6 : 1
350 rpm
3 h
KOH, NaOH
Hossain and Boyce (2009) [15]
Soybean oil
Methanolethanol, butanol
50°C–65°C
—
0.5%
1 : 4, 1 : 3, 1 : 2, 1 : 1
—
2 h and 6 h
NaOH
Hossain et al. (2010) [45]
Canola oil
Methanolethanol, butanol
Base-catalyzed transesterification
—
0.5%
1 : 4, 1 : 3, 1 : 2, 1 : 1
250 rpm
2 h and 6 h
NaOH
Hossain et al. (2010) [46]
Palm oil
Methanol
Heterogeneous transesterification
90°C–150°C
2–4
—
20 : 1, 30 : 1, 40 : 1
120, 180, and 240 min
ZrO2
Wan Omar and Saidina Amin (2011) [47]
Palm oil
Methanol
Esterification
50°C–65°C
1–4%
—
1 : 6, 1 : 1-0, 1 : 15
700 rpm
15–90 min
Ion-exchange resin catalysts
Gan et al. (2012) [48]
5. Conclusion
Cost of biodiesel can be reduced by using waste cooking oil as feed stock. High fatty acid content in waste cooking oil could be reduced by pretreating waste cooking oil with acid catalyst. Water produced during the esterification process can inhibit acid catalyst, and this can be eliminated by stepwise reaction mechanism. Methanol is the most suitable alcohol because of its low cost and easy separation from biofuel. Methanol to oil ratio for the acid-catalyzed reaction depends on amount of free fatty acid. For base-catalyzed reaction, 6 : 1 is optimum ratio for transesterification reaction. Concentration of catalyst depends on nature of catalyst used: either heterogeneous or homogenous. Stirrer speed helps to enhance rate of reaction. In most cases, optimum speed of stirrer was maintained in the range of 200–250 rpm.
GuptaP. K.KumarR.PanesarB. S.ThaparV. K.Parametric studies on bio-diesel prepared from rice bran oil20079EE 06-007AlamuO. J.AkintolaT. A.EnweremaduC. C.AdelekeA. E.Characterization of palm-kernel oil biodiesel produced through NaOH-catalysed transesterification process2008373083112-s2.0-69149089952FarikuS.NdonyaA. E.BitrusP. Y.Biofuel characteristics of beniseed (Sesanum indicum) oil2007621244224432-s2.0-36048994563ConnemannJ.FischerJ.Biodiesel processing technologiesProceedings of the International Liquid Biofuels CongressJuly 1998UllahF.NosheenA.HussainI.BanoA.Base catalyzed transesterification of wild apricot kernel oil for biodiesel production2009814328932932-s2.0-68949162830DiwaniG. E.AttiaN. K.HawashS. I.Development and evaluation of biodiesel fuel and by-products from jatropha oil2009622192242-s2.0-63449113648LichtF. O.The Global Renewable Fuels Alliance is a non-profit organization dedicated to promoting biofuel friendly policies internationally2011CanakciM.The potential of restaurant waste lipids as biodiesel feedstocks20079811831902-s2.0-3374814779710.1016/j.biortech.2005.11.022SuppleB.Howard-HildigeR.Gonzalez-GomezE.LeahyJ. J.The effect of steam treating waste cooking oil on the yield of methyl ester20027921751782-s2.0-0036474207LeungD. Y. C.WuX.LeungM. K. H.A review on biodiesel production using catalyzed transesterification2010874108310952-s2.0-7314912378310.1016/j.apenergy.2009.10.006RiceB.FröhlichA.LeonardR.Bio-diesel production from camelina oil, waste cooking oil and tallow1998FengY.YangQ.WangX.LiuY.LeeH.RenN.Treatment of biodiesel production wastes with simultaneous electricity generation using a single-chamber microbial fuel cell201110214114152-s2.0-7795735993410.1016/j.biortech.2010.05.059The Endress+Hauser Group, http://www.au.endress.com/VicenteG.MartınezM.AraciJ.Integrated biodiesel production: a comparison of different homogeneous catalysts systems200492297305HossainA. B. M. S.BoyceA. N.Biodiesel production from waste sunflower cooking oil as an environmental recycling process and renewable energy20091543123172-s2.0-77951170742HossainA. B. M. S.NasrulhaqB. A.SallehA.ChandranS.Biodiesel production from waste soybean oil biomass as renewable energy and environmental recycled process2010927423342402-s2.0-77954877820CorroG.TellezN.AyalaE.Marinez-AyalaA.Two-step biodiesel production from Jatropha curcas crude oil using SiO2·HF solid catalyst for FFA esterification step20108910281528212-s2.0-7795478236710.1016/j.fuel.2010.04.023LiuS.McDonaldT.WangY.Producing biodiesel from high free fatty acids waste cooking oil assisted by radio frequency heating2010284500518HighinaB. K.BugajeI. M.UmarB.Biodiesel production from Jatropha caucus oil in a batch reactor using zinc oxide as catalyst201129146149ArunN.SampathM.SiddharthS.PrasaanthR. A.Experimental Studies of base catalyzed transesterification of karanja oil201122351356MarchettiJ. M.MiguelV. U.ErrazuA. F.Possible methods for biodiesel production20071113001311LeungD. Y. C.GuoY.Transesterification of neat and used frying oil: optimization for biodiesel production200687108838902-s2.0-3374891763810.1016/j.fuproc.2006.06.003GuzattoR.De MartiniT. L.SamiosD.The use of a modified TDSP for biodiesel production from soybean, linseed and waste cooking oil20119210208220882-s2.0-7996055524510.1016/j.fuproc.2011.06.013VicenteG.MartınezM.AracilJ.Integrated biodiesel production: a comparison of different homogeneous catalysts systems200492297305WuY. G.LinY.ChangC. T.Combustion characteristics of fatty acid methyl esters derived from recycled cooking oil20078628102816OkulloA.TemuA. K.OgwokP.NtalikwaJ. W.The physico-chemical properties of jatropha and castor oils2012214752ZhangJ.ChenS.YangR.YanY.Biodiesel production from vegetable oil using heterogenous acid and alkali catalyst20108910293929442-s2.0-7795479762310.1016/j.fuel.2010.05.009BoeyaP. L.GanesanaS.ManiambG. P.KhairuddeanaM.Catalysts derived from waste sources in the production of biodiesel using waste cooking oil2012190117121TaufiqurrahmiN.MohamedA. R.BhatiaS.Production of biofuel from waste cooking palm oil using Nano crystalline zeolite as catalyst: process optimization studies20111021068610694ZhengaS.KatesbM.DubeaM. A.Mc LeanD. D.Acid-catalyzed production of biodiesel from waste frying oil200630267272OmarW. N. N. W.AminN. A. S.Biodiesel production from waste cooking oil over alkaline modified zirconia catalyst20119223972405PerezG.2003KumariA.MahapatraP.GarlapatiV. K.BanerjeeR.Enzymatic transesterification of Jatropha oil20092article 12-s2.0-6084910951710.1186/1754-6834-2-1MacEirasR.CancelaA.VegaM.MárquezM. C.Enzymatic alholysis for biodiesel production from waste cooking oil19103107IsoM.ChenB.EguchiM.KudoT.ShresthaS.Production of biodiesel fuel from triglycerides and alcohol using immobilized lipase200116153582-s2.0-003592338310.1016/S1381-1177(01)00045-5BalasubramaniamB.PerumalA. S.JayaramanJ.ManiJ.RamanujamP.Comparative analysis for the production of fatty acid alkyl esterase using whole cell biocatalyst and purified enzyme from Rhizopus oryzae on waste cooking oil (sunflower oil)20123215391547YagizF.KazanD.AkinA. N.Biodiesel production from waste oils by using lipase immobilized on hydrotalcite and zeolites20071341–32622672-s2.0-3454822202610.1016/j.cej.2007.03.041DevanesanM. G.ViruthagiriT.SugumarN.Transesterification of Jatropha oil using immobilized Pseudomonas fluorescens2007621249725012-s2.0-36049043708Al-WidyanM. I.Al-ShyoukhA. O.Experimental evaluation of the transesterification of waste palm oil into biodiesel20028532532562-s2.0-003697807210.1016/S0960-8524(02)00135-9CvengrošJ.CvengrošováZ.Used frying oils and fats and their utilization in the production of methyl esters of higher fatty acids20042721731812-s2.0-194247014610.1016/j.biombioe.2003.11.006FelizardoP.Neiva CorreiaM. J.RaposoI.MendesJ. F.BerkemeierR.BordadoJ. M.Production of biodiesel from waste frying oils20062654874942-s2.0-3364493657110.1016/j.wasman.2005.02.025WangY.Pengzhan LiuS. O.ZhangZ.Preparation of biodiesel from waste cooking oil via two-step catalyzed process20074811841882-s2.0-3374966231110.1016/j.enconman.2006.04.016RefaatA. A.AttiaN. K.SibakH. A.El SheltawyS. T.ElDiwaniG. I.Production optimization and quality assessment of biodiesel from waste vegetable oil20085175822-s2.0-38849121281ChhetriA. B.WattsK. C.IslamM. R.Waste cooking oil as an alternate feedstock for biodiesel production20081131810.3390/en1010003HossainA. B. M. S.NasrulhaqB. A.SallehA.ChandranS.Biodiesel production from waste soybean oil biomass as renewable energy and environmental recycled process2010927423342402-s2.0-77954877820HossainA. B. M. S.BoyceA. N.SallehA.ChandranS.Impacts of alcohol type, ratio and stirring time on the biodiesel production from waste canola oil2010514185118592-s2.0-77956002393Wan OmarW. N. N.Saidina AminN. A.Optimization of heterogeneous biodiesel production from waste cooking palm oil via response surface methodology2011353132913382-s2.0-7945147390110.1016/j.biombioe.2010.12.049GanS.NgH. K.ChanP. H.LeongF. L.Heterogeneous free fatty acids esterification in waste cooking oil using ion-exchange resins20121026772LoteroE.LiuY.LopezD. E.SuwannakarnK.BruceD. A.GoodwinJ. G.Synthesis of biodiesel via acid catalysis20054414535353632-s2.0-2294444804810.1021/ie049157gAhmadM.RashidS.KhanM. A.ZafarM.SultanaS.GulzarS.Optimization of base catalyzed transesterification of peanut oil biodiesel2009834414462-s2.0-60549104242AhmadM.AhmedS.HassanF. U.ArshadM.KhanM. A.ZafarM.SultanaS.Base catalyzed transesterification of sunflower oil biodiesel2010950863086352-s2.0-78650621687ShahS.SharmaS.GuptaM. N.Enzymatic transesterification for biodiesel production20034063923992-s2.0-3042806596JiangS. T.ZhangF. J.PanL. J.Sodium phosphate as a solid catalystfor biodiesel preparation20102711371442-s2.0-77952018953El SherbinyS. A.RefaatA. A.El SheltawyS. T.Production of biodiesel using the microwave technique2010143093142-s2.0-7864975992910.1016/j.jare.2010.07.003Van GerpenJ.Biodiesel processing and production20058610109711072-s2.0-1814441862910.1016/j.fuproc.2004.11.005KnotheG.SteidleyK. R.A comparison of used cooking oils: a very heterogeneous feedstock for biodiesel200910023579658012-s2.0-6864910012810.1016/j.biortech.2008.11.064MuthuH.SelvabalaV. S.VarathacharyT. K.SelvarajD. K.NandagopalJ.SubramanianS.Synthesis of biodiesel from neem oil using sulfated zirconia via tranesterification20102746016082-s2.0-78651476398MathiyazhaganM.GanapathiA.JaganathB.RenganayakiN.SasirekaN.Production of biodiesel from non-edible plant oils having high FFA content201122119122ChenL.YinP.LiuX.YangL.YuZ.GuoX.XinX.Biodiesel production over copper vanadium phosphate20113611751802-s2.0-7865074703510.1016/j.energy.2010.10.056RoyonD.DazM.EllenriederG.LocatelliS.Enzymatic production of biodiesel from cotton seed oil using t-butanol as a solvent20079836486532-s2.0-3374857528910.1016/j.biortech.2006.02.021NoshadiI.AminN. A. S.ParnasR. S.Continuous production of biodiesel from waste cooking oil in a reactive distillation column catalyzed by solid heteropolyacid: optimization using response surface methodology (RSM)201294156164FreedmanB.ButterfieldR.PrydeE.Transesterification kinetics of soybean oil1986631013751380FreedmanB.PrydeE. H.MountsT. L.Variables affecting the yields of fatty esters from transesterified vegetable oils1984611016381643LiS.WangY.DongS.ChenY.CaoF.ChaiF.WangX.Biodiesel production from Eruca Sativa Gars vegetable oil and motor, emissions properties2009347187118762-s2.0-6094908524710.1016/j.renene.2008.12.020TanK. T.LeeK. T.MohamedA. R.Potential of waste palm cooking oil for catalyst-free biodiesel production2011364208520882-s2.0-7995241867010.1016/j.energy.2010.05.003KiakalaiehA. T.AminN. A. S.ZareiA.NoshadiI.Transesterification of waste cooking oil by heteropoly acid (HPA) catalyst: optimization and kinetic model2013102283292DehkordiA. M.GhasemM.Transesterification of waste cooking oil to biodiesel using Ca and Zr mixed oxides as heterogeneous base catalysts2012974551CanakciM.Van GerpenJ.A pilot plant to produce biodiesel from high free fatty acid feedstocks20034649459542-s2.0-0242381942AdeyemiN. A.MohiuddinA.JameelT.Waste cooking oil transesterification: influence of impeller type, temperature, speed and bottom clearance on FAME yield2011104489148929SivasamyA.CheahK. Y.FornasieroP.KemausuorF.ZinovievS.MiertusS.Catalytic applications in the production of biodiesel from vegetable oils2009242783002-s2.0-6554914131710.1002/cssc.200800253ZhangY.DubéM. A.McLeanD. D.KatesM.Biodiesel production from waste cooking oil.1: process design and technological assessment20038911162-s2.0-003741173310.1016/S0960-8524(03)00040-3DarnokoD.CheryanM.Kinetics of palm oil transesterification in a batch reactor20007712126312672-s2.0-0034318182KapilakarnK.PeugtongA.A comparison of costs of biodiesel production from transesterication200781162-s2.0-74049104710DiasJ. M.FerrazC. A.AlmeidaM. F.Using mixtures of waste frying oil and pork lard to produce biodiesel200844ChenK. S.LinY. C.HsuK. H.WangH. K.Improving biodiesel yields from waste cooking oil by using sodium methoxide and a microwave heating system201238151156RefaatA. A.Different techniques for the production of biodiesel from waste vegetable oil201071183213