Mathematical Problems in Engineering

Volume 2014 (2014), Article ID 151095, 12 pages

http://dx.doi.org/10.1155/2014/151095

Research Article

Enhanced Control Design of Discrete-Time Takagi-Sugeno State-Multiplicative Noisy Systems

Dušan Krokavec and Anna Filasová

Department of Cybernetics and Artificial Intelligence, Faculty of Electrical Engineering and Informatics, Technical University of Košice, Letná 9, 042 00 Košice, Slovakia

Received 4 December 2013; Revised 21 February 2014; Accepted 25 February 2014; Published 13 April 2014

Academic Editor: Shuping He

Copyright © 2014 Dušan Krokavec and Anna Filasová. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

Design conditions for existence of the state feedback control for Takagi-Sugeno fuzzy discrete-time stochastic systems with state-multiplicative noise, stabilizing the closed-loop in such way that the quadratic performance in the mean is satisfied, are presented in the paper. Using newly introduced enhanced form of the bounded real lemma for such stochastic systems, the LMI-based procedure is provided for computation of gain matrices of the state control law, realized in the parallel distributed compensation structure. The approach is illustrated on an example, demonstrating the validity of the proposed method.

1. Introduction

The control design for systems with stochastic uncertainties is an area of study for several decades (see [1] and the references therein) and so far these practically and theoretically attractive fields derived numerous solutions. An approach, in which the parameter uncertainties were modeled as white noise processes in a linear system, was firstly applied for discrete-time systems [2] and continuous-time systems [3–5]. Unfortunately, this way of doing it on linear quadratic optimal control principle and reflecting the control input as a deterministic function of system state naturally led mainly to a nonstandard Riccati equation. Representing the system uncertainty by unknown disturbance signal in the system equations, stayed the most prominent method of dealing with the corresponding control problem of disturbance relaxation [6]. Combining both representations of uncertainty, adapting approach towards the disturbance attenuation for stochastic systems, and including those that ensure a performance bound in the sense, new accessions have been made in diverse practical problems for finite and infinite time horizons for continuous-time [7, 8] as well as for discrete-time stochastic systems [9–11], denoting later such systems as linear stochastic systems with multiplicative noise. The stochastic control for linear and nonlinear systems with multiplicative noises has founded its applications in many fields in control theory. Such models are encountered mainly in constrain control [12] and in gain scheduling when the scheduling parameters are corrupted with measurement noise [13].

In contrary to the linear framework, nonlinear systems are too complex to be represented by unified mathematical resources, and so a generic method has not been developed yet to design a controller valid for nonlinear stochastic systems with multiplicative noise [14]. An alternative is Takagi-Sugeno (TS) fuzzy approach [15], which benefits from the advantages of suitable linear approximation. Using the TS fuzzy model, each rule utilizes the local system dynamics by a linear model and the nonlinear system is represented by a collection of fuzzy rules. Recently, TS model based fuzzy control approaches are being fast and successfully used in nonlinear control frameworks. As a result, a range of stability analysis conditions [16], as well as control design methods [17–20], have been developed for TS fuzzy systems, relying mostly on the feasibility of an associated set of linear matrix inequalities (LMI) [21, 22]. An important fact is that the design problem is a standard feasibility problem with several LMIs. According to the T-S fuzzy model with multiplicative noise, there exist only few approaches investigated to solve the above-mentioned problems of control design and stability analysis for continuous-time [23, 24], as well as for discrete-time TS models [25–27] and these papers only present some results on stability analysis, mean-square stabilization, and control for TS fuzzy stochastic systems with multiplicative noises.

Considering actual results in bounded real lemma forms for discrete-time stochastic systems [8, 14], new design conditions, based on an enhanced form of the bounded real lemma for TS fuzzy discrete-time stochastic systems with state-multiplicative noise and control of such systems, are derived in the paper. For some potential numerical problems, there are also posed viewpoints and clarification for discrete-time TS fuzzy model [28], used in simulation.

To present this, the paper is arranged in the next sections as follows. Following the introduction in Section 1, the control design task for discrete-time TS fuzzy stochastic systems with state-multiplicative noise is presented in Section 2. The preliminary results, focused in consequence on two rudimentary bounded real lemma forms for such defined stochastic systems, are presented in Section 3 and, subsequently, Section 4 provides the controller design conditions in equivalent forms of LMIs. Section 5 illustrates the control design task by a numerical solution and Section 6 draws some conclusions.

Throughout the paper, the notations are narrowly standard in such way that , denote the transpose of the vector and matrix , respectively, , (≥0), means that is a symmetric positive definite (semidefinite) matrix, designates a block diagonal matrix, the symbol indicates the th-order identity matrix, is the set of all positive integers, indicates the set of real numbers, remits expectation with respect to the variable , , refer to the set of all -dimensional real vectors and real matrices, respectively, entails the space of square summable functions over , and is the Kronecker delta function [29].

2. Problem Formulation

Through the paper, the task is concerned with state feedback design to control a TS fuzzy stochastic discrete-time dynamic system, given by the set of equations

where the initial condition is known, , , and are the state, input, and output vectors, respectively, is an exogenous disturbance vector, , , , , and are real matrices and . The scalar function is the weight for th fuzzy rule, satisfying, by definition, the property

which is the vector of the premise variables, where , are the numbers of fuzzy rules and premise variables, respectively. It is supposed in the next that all premise variables are measurable and independent of  . More details can be found, for example, in [18, 21].

It is assumed that , , satisfies the condition

and disturbance is a random vector sequence .

The problem of interest is to design in the mean square sense stable closed-loop system by the overall fuzzy state feedback controller in the parallel distributed compensation (PDF) form

which uses the same set of normalized membership functions (3) and , is the set of feedback controller gain matrices. It is supposed that all couples are controllable.

3. Basic Preliminaries

Lemma 1 (a TS sector approximation of the function sine). The function sine can be approximated on the interval as

where , are the sector bounds and the fuzzy membership functions take the forms

Proof (compare [30]). Since it can be considered that

and (3) implies

then (7) can be written as

Thus, evidently, the real fuzzy membership functions have to take the forms

Approximating for the left bounded sector, that is, , , then (12) implies (8).

It is evident that if and , then (7) gives a trivial solution

Remark 2. Very often the fuzzy membership functions in the above given task are defined as simple triangles [31]; that is,

Moreover, the minimal sector value is often considered approximately as , or .

Lemma 3. If , are matrices of appropriate dimension and is a symmetric positive definite matrix, then

Proof. Since , then

respectively. It is evident that (17) implies (15).

Lemma 4. If is a symmetric positive definite matrix, are matrices of appropriate dimension, is a real scalar, , and is a positive integer, then

and, if ,

Proof. Considering (18), it can be written as

then, using (15), we have

Evidently, (21) implies (18).

Lemma 5 (bounded real lemma). The deterministically unforced system (1) and (2) is stable in the mean square sense and with the quadratic performance if there exist a positive definite matrix and a positive scalar such that for all

Here and hereafter, denotes the symmetric item in a symmetric matrix.

Proof. Let the Lyapunov function candidate be

where is square of the norm of the transfer function matrix for the disturbance input and the system output .

Taking expectation with respect to , then it yields

Solving for the deterministically unforced system (1) and (2), the following is obtained:

Considering (19), then the substitution of (5) and (26) in (25) gives

Defining the composite vector

the next inequality has to be satisfied

if

Writing (30) as follows

and using the Schur complement property, (31) can be rewritten in the next form:

Applying twice again the Schur complement property, (32) implies (23). This concludes the proof.

Remark 6. The inequality (23) represents the standard bounded real lemma form (compare, e.g., [32, page 66], for continuous-time linear systems). If it is necessary to reduce the range of setting (defined by ), Lyapunov function candidate can be selected in the form

Now the conditions that also satisfied are

Note, in the same way, the structure of (35) is used in the following lemmas and theorems.

Lemma 7 (enhanced bounded real lemma). The deterministically unforced system (1) and (2) is stable in the mean square sense and with the quadratic performance if there exist positive definite matrices and a positive scalar such that for all

Proof. Since , for the deterministically unforced system (1), it is implied that

Then, with an arbitrary symmetric positive definite matrix , it is yielded that

and also

respectively. Adding (40) as well as its transposition to (25) gives

Defining the composite vector

and using (19), then (41) can be written as

where, for all ,

Using Schur complement property to construct the LMI form, (44) can be rewritten as (37). This concludes the proof.

Remark 8. The inequality (37) is an enhanced representation of bounded real lemma for a given class of TS stochastic systems. The inequality is linear with respect to the system variables and does not involve any product of the Lyapunov matrix and the system matrices . This offers its main possibility to be applied in systems with polytopic uncertainties.

Remark 9. To incorporate noise variance into design condition, the choice of (39) is not unique. Another, but more conservative, solution can be obtained if (39) is chosen, for example, as

4. State Feedback Control

This section addresses the problem of finding the state feedback control law (6), working on the parallel distributed compensation concept that stabilizes the system (1), (2) and achieves some level of attenuation. Moreover, since the LMI solvers mostly limit the maximal number of LMIs entering a solution, the number of LMIs in the following design conditions is minimized.

Theorem 10. The state feedback control (6) to system (1), (2) exists if there exist a symmetric positive definite matrix , matrices , and a positive scalar such that

for all , , , and , respectively.

When the above conditions hold, the control law gain matrices are given as

Proof. Considering the control law (6), then (27) implies

where

Permuting the subscripts and in (50) gives

and with (28) it yields

where, in analogy with (30),

Rearranging the computation, (30) can be written as

respectively.

Replacing in (23) by the closed-loop system matrix (51) then, with respect to (55) and (56), it is

respectively. Defining the transform matrix

then premultiplying and postmultiplying of the left-hand side and the right-hand side of (58) and (59) by (51) give

Thus, with the notations

Equations (60) and (61) imply (47) and (48), respectively. This concludes the proof.

Applying this result directly to system (1), (2) would lead, in the case of a large number of rules, to a possibly conservative analysis, since a common symmetric positive definite matrix is used to verify all Lyapunov inequalities. Considering the enhanced bounded real lemma form (36), (37), main aim of next theorem is to extend the affine TS model properties using slack matrix variables to decouple Lyapunov matrix and the system matrices in LMIs.

Theorem 11. The state feedback control (6) to system (1) and (2) exists if there exist symmetric positive definite matrices , matrices , and a positive scalar such that for all

When the above conditions hold, the set of control law gain matrices is given as (49).

Proof. With respect to the control law form (6), then (41), (43), and (44) give

where is given in (51). Thus, considering (42) and (43), it is

where

Permuting the subscripts and in (69) leads to

and so

respectively. Subsequently, exploiting the Schur complement property, it can be obtained that

Since it was supposed that is positive definite, performing a congruence transformation by

that is, premultiplying and postmultiplying the left-hand side and the right-hand side of (74) and (75) by (76), then

Thus, with the notations

Equations (77) and (78) imply (65) and (66), respectively. This concludes the proof.

Note, the LMIs in Theorem 11 are linear and the equivalent Lyapunov matrix , used to verify all inequalities, is a symmetric positive definite matrix.

5. Illustrative Example

To demonstrate the control properties, the trailer-like mobile robot kinematics is considered [33], described by the following set of differential equations:

where is the steering angle (rad), is the angle difference between truck and trailer (rad), is the angle of trailer (rad), is position of rear end of trailer (m), is position of rear end of trailer (m), is the constant speed of the backward movement (m/sek), is the length of truck (m), and is the length of trailer (m).

The control purpose is to realize the backward movement of the trailer-like mobile robot along the , that is, to regulate by manipulating the steering angle , where, without forward movements,

Consequently, the variable is not necessary to take into account.

If and are always small values, the above model can be simplified as

Applying Euler discretization, the next difference equation forms are obtained (compare, e.g., [34]):

where (s) is the sampling period.

Defining the premise variable and the sector values as

then (12) implies

and the solitary nonlinear difference equation can be approximated as

Considering the external disturbance and the multiplicative noise only in the indirect measurement of , it is given that [35]

where is the constant gain of multiplicative noise and is the constant gain of disturbance. Subsequently, the output equation is defined as

Now, introducing the state vector

the discrete-time TS fuzzy model takes the form

where

Note, the main reason of using the above approximation for is to obtain a controllable pair . Be aware that for very small value of , the stability of the system may be close to the limit.

To demonstrate the control properties, the next system parameters were considered:

Solving (64)–(66) with respect to the LMI variables ,, , , and using Self-Dual-Minimization (SeDuMi) package of MATLAB [36], the feedback gain matrix design problem was feasible with the results

giving the feedback gain matrices

In consequence, the linear state feedback control law was obtained for such system.

The obtained control law insures the stable control in the mean square sense. The closed-loop subsystem matrix eigenvalue spectra are as follows:

which implies also the whole closed-loop system stability.

To compare, using the same system parameters, (46)–(48) give

and, by Theorem 10, the design parameters were computed as follows:

which give less relative damping of closed-loop system solutions than there were obtained in the first case.

Since the conditions of Theorems 10 and 11 are all satisfied and the design tasks were feasible, it is possible to conclude that the TS fuzzy control of given stochastic system with state-multiplicative noise is asymptotically stable in the mean with the quadratic performance by applying the linear control law.

The simulation presents the closed-loop system properties, where the multiplicative noise parameters were chosen as in (5), the disturbance was modeled as noise with covariance , and the initial system state vector was (in degrees)

Figure 1 shows the output response of the controlled nonlinear system with the TS fuzzy controller (6) designed according to the conditions of Theorem 11, where the associated input signal is presented in Figure 2. For comparison, Figures 3 and 4 show the responses of and the control input for the closed-loop system with the fuzzy controller designed according to the conditions of Theorem 10, respectively.

Figure 1: The response of for the system with TS fuzzy controller designed according to the conditions of Theorem 11.

Figure 2: Input signal for the system with TS fuzzy controller designed according to the conditions of Theorem 11.

Figure 3: The response of for the system with TS fuzzy controller designed according to the conditions of Theorem 10.

Figure 4: Input signal for the system with TS fuzzy controller designed according to the conditions of Theorem 10.

6. Concluding Remarks

The paper presents the control design principle for TS fuzzy discrete-time stochastic multivariable dynamic systems with state-multiplicative noise. The stability of the control scheme is established in the mean square sense and with the quadratic performance using an enhanced representation of bounded real lemma for such TS fuzzy stochastic systems. As a result, the Lyapunov matrix and the system parameter matrices are decoupled in the resulting LMIs. This provides a suitable way for determination of state control by solving these naturally affine LMI problems. Compared with the previous results, the number of assumptions is reduced since the solutions obtained according to the conditions of both presented theorems tend to receive a linear state controller.

Presented applications can be considered as a task concerning the class of stabilization control problems where the design conditions were newly formulated. This formulation poses the problem as a stabilization problem with a fuzzy state feedback controller in the parallel distributed form whose gain matrices take no special structures and allows finding a solution to the control law without restrictive assumptions and additional specifications on the design parameters. The procedures used here for discrete-time TS fuzzy stochastic systems with state-multiplicative noise can be similarly extended for the continuous-time case.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The work presented in this paper was supported by VEGA, the Grant Agency of the Ministry of Education, and the Academy of Science of Slovak Republic under Grant no. 1/0348/14. This support is very gratefully acknowledged.

References

E. Gershon, U. Shaked, and I. Yaesh, H ∞ Control and Estimation of State-Multiplicative Linear Systems, vol. 318, Springer, London, UK, 2005.

S. M. Joshi, “On optimal control of linear systems in the presence of multiplicative noise,” IEEE Transactions on Aerospace and Electronic Systems, vol. 12, no. 1, pp. 80–84, 1976.

P. McLane, “Optimal stochastic control of linear systems with state- and control-dependent disturbances,” IEEE Transactions on Automatic Control, vol. 16, no. 6, pp. 793–798, 1971.

Y. A. Phillis, “Controller design of systems with multiplicative noise,” IEEE Transactions on Automatic Control, vol. 30, no. 10, pp. 1017–1019, 1985.

L. El Ghaoui, “State-feedback control of systems with multiplicative noise via linear matrix inequalities,” Systems & Control Letters, vol. 24, no. 3, pp. 223–228, 1995.

K. Zhou, J. C. Doyle, and K. Glover, Robust and Optimal Control, Prentice Hall, Upper Saddle River, NJ, USA, 1996.

D. Hinrichsen and A. J. Pritchard, “Stochastic ,” SIAM Journal on Control and Optimization, vol. 36, no. 5, pp. 1504–1538, 1998.

H. Gao and C. Wang, “Improved bounded real lemma for continuous-time stochastic systems with polytopic uncertainties,” in Proceedings of the American Control Conference (AAC '04), pp. 2654–2658, Boston, Mass, USA, July 2004.

O. L. V. Costa and C. S. Kubrusly, “State feedback -control for discrete-time infinite-dimensional stochastic bilinear systems,” Journal of Mathematical Systems, Estimation, and Control, vol. 6, no. 2, pp. 1–32, 1996.

A. El Bouhtouri, D. Hinrichsen, and A. J. Pritchard, “-type control for discrete-time stochastic systems,” International Journal of Robust and Nonlinear Control, vol. 9, no. 13, pp. 923–948, 1999.

E. Gershon and U. Shaked, “ output-feedback control of discrete-time systems with state-multiplicative noise,” Automatica, vol. 44, no. 2, pp. 574–579, 2008.

D. Krokavec and A. Filasová, “Constrained control of discrete-time stochastic systems,” in Proceedings of the 17th World Congress, International Federation of Automatic Control (IFAC '08), pp. 15315–15320, Seoul, Korea, July 2008.

E. Todorov, “Stochastic optimal control and estimation methods adapted to the noise characteristics of the sensorimotor system,” Neural Computation, vol. 17, no. 5, pp. 1084–1108, 2005.

E. Gershon and U. Shaked, Advanced Topics in Control and Estimation of State-Multiplicative Noisy Systems, vol. 439, Springer, London, UK, 2013.

T. Takagi and M. Sugeno, “Fuzzy identification of systems and its applications to modeling and control,” IEEE Transactions on Systems, Man and Cybernetics, vol. 15, no. 1, pp. 116–132, 1985.

M. Johansson, A. Rantzer, and K.-E. Årzén, “Piecewise quadratic stability of fuzzy systems,” IEEE Transactions on Fuzzy Systems, vol. 7, no. 6, pp. 713–722, 1999.

I. Abdelmalek, N. Goléa, and M. L. Hadjili, “A new fuzzy Lyapunov approach to non-quadratic stabilization of Takagi-Sugeno fuzzy models,” International Journal of Applied Mathematics and Computer Science, vol. 17, no. 1, pp. 39–51, 2007.

D. Krokavec and A. Filasová, “Optimal fuzzy control for a class of nonlinear systems,” Mathematical Problems in Engineering, vol. 2012, Article ID 481942, 29 pages, 2012.

J. Pan, S. Fei, Y. Ni, and M. Xue, “New approaches to relaxed stabilization conditions and H-infinity control designs for T-S fuzzy systems,” Journal of Control Theory and Applications, vol. 10, no. 1, pp. 82–91, 2012.

M. P. A. Santim, M. C. M. Teixeira, W. A. de Souza, R. Cardim, and E. Assunção, “Design of a Takagi-Sugeno fuzzy regulator for a set of operation points,” Mathematical Problems in Engineering, vol. 2012, Article ID 731298, 17 pages, 2012.

K. Tanaka and H. O. Wang, Fuzzy Control Systems Design and Analysis. A Linear Matrix Inequality Approach, John Wiley & Sons, New York, NY, USA, 2001.

G. Feng, Analysis and Synthesis of Fuzzy Control Systems. A Model-Based Approach, Taylor & Francis, Boca Raton, Fla, USA, 2010.

C.-C. Ku, P.-H. Huang, and W.-J. Chang, “Passive fuzzy controller design for nonlinear systems with multiplicative noises,” Journal of the Franklin Institute: Engineering and Applied Mathematics, vol. 347, no. 5, pp. 732–750, 2010.

W.-J. Chang, C.-C. Ku, and C.-H. Chang, “PDC and non-PDC fuzzy control with relaxed stability conditions for contintuous-time multiplicative noised fuzzy systems,” Journal of the Franklin Institute: Engineering and Applied Mathematics, vol. 349, no. 8, pp. 2664–2686, 2012.

W.-J. Chang, L.-Z. Liu, and C.-C. Ku, “Passive fuzzy controller design via observer feedback for stochastic takagi-sugeno fuzzy models with multiplicative noises,” International Journal of Control, Automation and Systems, vol. 9, no. 3, pp. 550–557, 2011.

W.-J. Chang and B.-J. Huang, “Variance and passivity constrained fuzzy control for nonlinear ship steering systems with state multiplicative noises,” Mathematical Problems in Engineering, vol. 2013, Article ID 687317, 10 pages, 2013.

W.-J. Chang, C.-C. Ku, and H.-J. Liang, “Actuator saturation constrained fuzzy control for discrete stochastic fuzzy systems with multiplicative noises,” Mathematical Problems in Engineering, vol. 2013, Article ID 732939, 10 pages, 2013.

K. Tanaka, S. Hori, and H. O. Wang, “Multiobjective control of a vehicle with triple trailers,” IEEE/ASME Transactions on Mechatronics, vol. 7, no. 3, pp. 357–368, 2002.

K. E. Atkinson, An Introduction to Numerical Analysis, John Wiley & Sons, New York, NY, USA, 2nd edition, 1989.

K. Tanaka and M. Sano, “A robust stabilization problem of fuzzy control systems and its application to backing up control of a truck-trailer,” IEEE Transactions on Fuzzy Systems, vol. 2, no. 2, pp. 119–134, 1994.

W.-J. Chang, W.-Y. Wu, and C.-C. Ku, “ constrained fuzzy control via state observer feedback for discrete-time TakagiSugeno fuzzy systems with multiplicative noises,” ISA Transactions, vol. 50, no. 1, pp. 37–43, 2011.

R. E. Skelton, T. Iwasaki, and K. M. Grigoriadis, A Unified Algebraic Approach to Linear Control Design, Taylor & Francis, London, UK, 1998.

M. Sampei, T. Tamura, T. Itoh, and M. Nakamichi, “Path tracking control of trailer-like mobile robot,” in Proceedings of the IEEE/RSJ International Workshop on Intelligent Robots and Systems (IROS '91), pp. 193–198, Osaka, Japan, November 1991.

K. Tanaka and T. Kosaki, “Design of a stable fuzzy controller for an articulated vehicle,” IEEE Transactions on Systems, Man, and Cybernetics B: Cybernetics, vol. 27, no. 3, pp. 552–558, 1997.

W. J. Chang, C. C. Shing, and W. Chang, “Constrained discrete fuzy control for a perturbed trailer type mobile robot stochastic system,” in Proceedings of the IEEE/ASME International Conference on Advances Intelligent Mechatronics (AIM '03), pp. 175–180, Kobe, Japan, 2003.

D. Peaucelle, D. Henrion, Y. Labit, and K. Taitz, User's Guide for SeDuMi Interface 1.04, LAAS-CNRS, Toulouse, France, 2002.