A New Approach for Enhancing the Services of the 5G Mobile Network and IOT-Related Communication Devices Using Wavelet-OFDM and Its Applications in Healthcare

The heart of the current wireless communication systems (including 5G) is the Fourier transform-based orthogonal frequency division multiplex (OFDM). Over time, a lot of research has proposed the wavelet transform-based OFDM as a better replacement of Fourier in the physical layer solutions because of its performance and ability to support network-intensive applications such as the Internet of Things (IoT). In this paper, we weigh the wavelet transform performances against the future wireless application system requirements and propose guidelines and approaches for wavelet applications in 5G waveform design. This is followed by a detailed impact on healthcare. Using an image as the test data, a comprehensive performance comparison between Fourier transform and various wavelet transforms has been done considering the following 5G key performance indicators (KPIs): energy efficiency, modulation and demodulation complexity, reliability, latency, spectral efficiency, effect of transmission/reception under asynchronous transmission, and robustness to time-/frequency-selective channels. Finally, the guidelines for wavelet transform use are presented. The guidelines are sufficient to serve as approaches for tradeoffs and also as the guide for further developments.


Introduction
e number of devices connected to the internet is on the increase. e advent of the IoT will make it an explosive one [1,2]. Almost every 10 years, a new generation of wireless communication standard is developed to meet the exponentially growing demand for fast and reliable connections. these classifications are subsets of IOT's requirements. eir requirements are not limited to multi-gigabit-persecond (Gbps) data rates, low latency, high spectral efficiency, high mobility, and high connection density [3]. We can, therefore, conclude that 5G will have to cope with a high degree of heterogeneity in terms of services and requirements. Surprisingly, the increasing number of certain new applications as well as newer, yet to be conceived applications, will require even greater data rates among other requirements than what 5G NR can offer [4], and some of those applications might not even fall completely within a single defined use-case [5]. A few of them are virtual/augmented reality (VR/AR), wireless cognition, and wireless backhaul. Furthermore, because of 5G's diversity, there possibly exist other undiscovered areas of applications such as in healthcare, of which IoT is obviously the enabler. Advances in a research area will impact the other; it is like a chain reaction; for example, 5G (as the underlying technology) will unlock IoT capabilities that were previously unattainable on 4G networks. It will introduce major innovations, such as higher connection speed, greater capacity, and lower latency. Over time, these benefits will lead to technological milestones that will have a significant impact on healthcare and other areas.
erefore, for an efficient IoT system, there is a need for a diverse network such as 5G. e advent of 5G has led to further exploration of new methodology, hardware, waveform design, underutilized millimeter-wave (mmwave) frequency, etc. e most prominent of these explorations but most challenging would be to design waveform for efficient signaling in 5G. e summary of the proposed waveforms is given in [6].
OFDM remains the key ingredient in waveform design for many multicarrier wireless communication schemes [7]. Proposed waveforms for 5G are mostly OFDM-inspired.
is reason is partly due to OFDM's use in 4G LTE and other standards, familiarity among the wireless society, and its maturity as a technology [8,9]. However, the gradual migration from cell-centric to user-centric processing is rendering OFDM unfeasible due to its intrinsic drawbacks. erefore, OFDM limitations such as the reduction in transmission throughput due to the use of cyclic prefix (CP), high peak-to-average power ratio (PAPR), sensitivity to carrier offset, and out-of-band emissions (OOB) are some of the problems solved in the proposed waveforms.
Attempts at combating some of the OFDM's limitations require an understanding of the root causes. For example, OOB emission (or spectral leakage) is introduced by band egress noise to neighboring bands and ingress noise from neighboring bands. is is because the spectral localization of the subcarriers is weak, resulting in spectral leakage. Filter bank multicarrier (FBMC) attempts to solve the aforementioned problem by direct suppression of the sidelobes using special filters. FBMC is spectrum-efficient, does not require redundant CP, and is robust to narrowband jammers. However, practical applications indicate that FBMC is vulnerable to multipath distortion due to a lack of CP. As a result, in practical cases whereby channel state information is not perfect, OFDM will perform better. Attempt to improve FBMC and adopt it in MIMO channels has been reported in [10] with a focus on channel uncertainty.
ere are other evident disadvantages of FBMC such as the introduction of overhead in overlapping symbols in the filter bank in the time domain and loss in bandwidth efficiency when transmitting short data packets. As a result, FBMC was extended to the generalized frequency division multiplex (GFDM) in [11]. GFDM is based on controlling the OOB of the transmitted signal by an adjustable pulse shaping filter applied to the individual carriers [12]. GFDM can be applied successfully in nonaccurate synchronization of users without problems. However, the GFDM scheme is not perfect; adjacent synchronization is affected by some level of interference. Attempts at solving this problem have been exploited in [12,13], but not without a significant increase in the transmitter's complexity.
Research progress led to circular FBMC (C-FBMC), a concept developed from GFDM and FBMC. C-FBMC is less complex, is easily extensible to the multiple-input multipleoutput (MIMO) antenna, and preserves the orthogonality of the subcarrier's symbols. Most of the other proposed waveforms are based on the schemes described above. ey either apply filtering or windowing operation (or both) in either the time or frequency domain. e aim of this section is not to review the literature but provide the basis for the waveform design. erefore, to keep the content of this article concise, no further review will be pursued here. A detailed review is given in [14]. e discrete wavelet transform (DWT) is another potential waveform candidate for OFDM design. Its application in the OFDM is known as orthogonal wavelet division multiplex (OWDM). e DWT-based signal coding was introduced in [15] followed by many research studies. Some of them are documented in [16][17][18][19][20][21][22]. However, these research scopes are generally not broad enough to support the research insights into future wireless application requirements. OWDM's fit for 5G is scarcely reported in the literature. e contribution of this paper is addressing this by checking for both merits and demerits of using OWDM and weighing them against what the future wireless applications require. e 3rd Generation Partnership Project (3GPP) group has selected CP-OFDM (a holdover from 4G) as the signaling option for 5G for the 3GPP's Release 15. erefore, we compared OWDM to CP-OFDM. We made a detailed comparison between Fourier transform-based CP-OFDM and OWDM using MATLAB, detailed its impact on healthcare, and proposed a guideline on how to approach wavelet application in 5G and beyond. e rest of this paper is organized as follows: 5G design criteria and its impacts on healthcare are discussed in Section 2. Sections 3 and 4 are about the OFDM and OWDM system model. Section 5 contains simulations and results. Section 6 evaluates the results based on the requirements, while Section 7 draws conclusions and reviews based on the results.

5G Design Criteria and Its Impacts on Healthcare
In order to give detailed simulation and comparison, we have taken into consideration all the necessary 5G KPIs [23] in gaging transmitter/receiver systems' efficiency.

High Energy Efficiency.
In Section 1, we defined PAPR as the peak-to-average power ratio of the transmission and reception energy. Energy efficiency is mostly defined by the PAPR and degree of computational complexity. At the physical layer, waveforms exhibit peaks and lows. e implication is that, at transmission (or reception), if the difference (ratio) between the peaks and lows is large, higher transient energy will result in the power amplifiers which in turn will lead to higher energy consumption. erefore, low PAPR is necessary for power-efficient transmissions at uplink (UL), downlink (DL), and side link (SL). Furthermore, computational complexity should be minimal, especially in power-stringent (battery-operated) devices such as the mobile phone or an IOT field sensor. In an IoT system, a further attempt at increasing the energy efficiency at the network layer has been reported in a recent study in [24]. It presents an information-centric networking (ICN) caching strategy that fits well in the energy-efficient IoT environment by utilizing Packet Update Caching (PUC). Considering all these advancements in research, it is safe to say the longevity of battery life and performance will be improved to ensure continuous and uninterrupted remote monitoring. Actually, in 5G, low-power sensors will be designed to operate on the same battery for the full duration of medical operation. is duration can be as much as 10 years [25].

Low Device Complexity.
is section could also be termed as transceiver baseband complexity. It is the number of operations required to be performed to transmit and, more importantly, receive a signal successfully with the minimum possible processing overhead. At a very high frequency (e.g., millimeter-wave) and large bandwidths, severe RF impairments may result. With the presence of impairments, the waveform design standard should maintain the least possible computational complexity and processing overhead that could result from filtering, reduction of intersymbol interference (ISI) and intercarrier interference (ICI), windowing, interference cancellation, etc. e direct implication of this is battery longevity. is is similar to what is discussed above.

High Reliability.
Reliability is evaluated by bit error rate (BER); it is the capability of a network to carry out a preferred operation with very low error rates. Biomedical sensors with IoT capabilities generate a huge amount of data, therefore error-sensitive. More so, considerable amounts of errors might lead to an increase in latency. Considering the signaling traffic from a massive number of these sensors would even lead to more increase in latency as each sensor is trying to retransmit. e low BER scheme will be supported by the 5G network. One of the main advantages of the proposed wavelet-OFDM scheme in this article is low BER compared to OFDM.

Low Latency.
Ultralow latency defines the network which is optimized to process huge amounts of data packet with a very low tolerance for delay. 5G maximum allowed latency for the ultrareliable low-latency communication (URLLC) applications is less than 1 ms. is is due to services such as machine-to-machine communication requiring fast response time to allow efficient sporadic transmission of small packets. So, it requires a transmission mode with low air-interface latency enabled by very short frames. e efficient transmission of short frames is very much essential for medical IoT. For example, in telesurgery, the maximum acceptable latency (end-to-end) is 200 ms [26]. Comparing this to the 5G network typical latency of less than 1 ms, "telesurgeons" can be guaranteed low latency communication and optimum stability in receiving haptic feedback and improved wireless data rates for better visualization and greater precision. In the future, this will serve as an enabling technology for new telesurgery applications alongside other real-time applications with stricter latency requirements. is can also serve as an enabling technology for emerging e-health fields requiring some forms of wireless transfer of big data and machine learning for early detection of certain diseases. ese diseases are not limited to heart disease [27], Parkinson [28], and breast cancer [29]. For further studies about latency reduction in 5G, refer to [30].

High Spectral Efficiency or High Bandwidth.
Bandwidth refers to the transmission capacity of a network per given time. Spectral efficiency refers to the efficient use of the available bandwidth. In the 3G and 4G networks, biomedical sensors can only send a limited amount of data due to restricted bandwidth [31]. is limitation is mitigated in 5G by exploring the available (untapped) spectrum at higher frequencies (as high as 10 GHz). Also, at such high frequencies, a higher transmission rate on the order of Gbps is achieved. With this, seamless remote monitoring can be achieved; physicians can view ultra-high-definition contents (videos and pictures) and be able to make better-informed decisions. Furthermore, online consultations can be carried out whereby patients, ordinary citizens, different civic associations, experts, and executive bodies can contribute and exchange medical information.
Having discussed the benefits of 5G's high spectral efficiency, it is necessary to note that several factors could also contribute to the degradation of its spectral efficiency (Sections 5.3 and 5.4).
is is why the nature of the waveform is more important. is is one of the problems addressed in the waveform scheme proposed in this article.

Massive Asynchronous Transmission.
Massive asynchronous transmission or asynchronous coexistence of a huge number of nodes will be achieved with 5G. is will be achieved with D2D [32]. In D2D communications, each Scientific Programming terminal can communicate with each other directly without routing through gateways and base stations. erefore, a highly dense network problem can be solved through D2D communications. D2D communications will enable asynchronous coexistence between a large number of medical sensors, wearables, and devices, and monitoring equipment can communicate with minimal interference.
In the 4G network, all communications are routed through gateways and base stations. is routing is inefficient, especially when devices are near each other. Achieving D2D communication will require waveforms with less strict synchronization requirements [33]. e effect of poor synchronization is phase noise. Phase noise including carrier frequency offset (CFO) is both caused by differences in the transmitter and receiver oscillator. e mathematical description of the CFO is the multiplication of a signal in the time domain by a time-varying complex exponential function. CFO will cause a received signal to be shifted in the frequency. erefore, sampling of the received signal will be done at an offset point, which is not the peak point. e result is a raised ICI [8].

MIMO Compatibility.
Massive MIMO is a key technology in delivering mobile 5G. is is essentially grouping together large-scale antennas at the transmitter and receiver to increase throughput and improve spectrum efficiency at the access nodes. Other benefits of massive MIMO are lower latency, simplification of the media access control (MAC) layer, and robustness against (intentional) jamming. Furthermore, beamforming is necessary for overcoming high propagation losses especially at very high frequencies. One of the direct impacts and implications of this is large file transfers. Hospitals will possess the ability to transfer large image files such as medical images. Overall, hospitals will be able to process more patients, given the same amount of time.
One of the various checks of our proposed waveform is its suitability and ease of integrating MIMO with it. It should be less complex and practicable.

Robustness to Frequency-Selective and Time-Selective
Channels. Very harsh propagation conditions can cause poor performance in a wireless communication system and result in a loss of signal power without loss of noise power, consequently resulting in a poor signal-to-noise ratio (SNR). OFDM is generally used to combat selective fading because of its robustness to frequency-selective channels. Among other methods are MIMO, rake receivers, spacetime codes, forward error correction, interleaving, etc. e robustness of the 5G waveform design should include adapting to this impairment as well as time-selective fading occurring in high-speed scenarios. An example of such a case is the vehicle to anything (V2X). In this case, we can consider the (efficient) transmission of the medical ultrasound video stream from a fast-moving ambulance to the host hospital.

OFDM System Model
OFDM is the most popular multicarrier modulation scheme that is currently being employed in many standards such as the downlink of 4G LTE and the IEEE 802.11 family [34]. In an OFDM system, at the transmitter, data to be transmitted are mapped to a constellation, split into parallel, and modulated using the inverse fast Fourier transform (IFFT). e modulation process is shown in Figure 1. Guard band and cyclic prefix (CP) are inserted to prevent a delayed version of symbol overlapping with the adjacent symbol and mitigate the delay spread, respectively. e orthogonal signals are then mixed. e key process here is modulation, where signals are mapped from the frequency domain to the time domain and multiplexed. e modulation process is mathematically the summation of N tones described in [35] and mathematically expressed in the following equation: (1) x n [t] is the summation of the number of complex-valued sinusoids N with period T in the continuous-time domain t. n denotes the discrete-time index. e data symbol is s k [n], with frequency component k � 0, 1, . . ., N − 1. e multiplexed data symbol y n (t) on the baseband is passed through a channel with transfer function H(f), which is expressed mathematically in the following equation: e sinusoids N are located at frequencies f � 0, 1/T, 2/T, . . . , (N − 1)/T for orthogonality. e orthogonality between two adjacent sinusoids is defined in the following equation: After modulation, the CP denoted as p is added by copying the last part of the modulated IFFT signal and appending it to the beginning as a guard interval to prevent ISI. In the 4G LTE system, the CP is hard-coded into the waveform, while for 5G NR Release 15, the CP is determined by the maximum delay present in individual channels.
At the receiver, the transmitting process is reversed to decode the received data. For demodulation, the fast Fourier transform (FFT) is employed. OFDM, as opposed to a single-carrier system, has the ability to cope with frequencyselective fading because data are divided and transmitted in parallel streams on a modulated set of subcarriers. is approach results in the efficient use of bandwidth.

OWDM System Model
Some of the wavelet transform applications are in source and channel coding, signal denoising, and data compression [36,37]. DWT and inverse discrete wavelet transform (IDWT) are used in OWDM [38,39]. is replacement is due to its properties such as orthonormality [40][41][42] and the ability to decompose signals effectively in the time-frequency domains by scaling and shifting. In DWT, the scaling (j) and shifting (k) results are generated by the mother wavelet denoted by Ψ as a function of time (t) and mathematically expressed in the following equation: e discrete wavelet and the inverse discrete wavelet representation of a signal are given by equations (5) and (6), respectively [43]: x is the input signal in the time domain. erefore, the OWDM symbol can be expressed as the weighted sum of wavelet and scale carriers and is mathematically expressed in the following equation: w j,k is the sequence of the wavelet, and a J,k are the approximation coefficients. e OWDM transmission and reception concept is the same with the OFDM; however, the modulation process is different. It makes use of IDWT for modulation and DWT for demodulation. is is highlighted in Figure 2. Starting with the modulation process, the data bits are mapped into OFDM symbols of parallel data stream corresponding to the number of subcarriers. is signal is converted to serial X(n) and fed into IDWT. Here, the signal is vector-transposed (V t ), upsampled (u s ), and convoluted with a low-pass filter (LPF) and high-pass filter (HPF) [44] using approximated coefficients (A c ) and detailed coefficients (D c ), respectively. e decomposed outputs from the LPF and HPF are L(n) and H(n), respectively. Different wavelet families have different filter lengths, so the length of the zero pads is adjusted accordingly to maintain orthonormality and orthogonality in L(n) and H(n). L(n) and H(n) are mixed and then transmitted.
At the receiver, the modulation process is simply reversed to decode the received data. e received data are decomposed back into L(n) and H(n) using the LPF and HPF, respectively. H(n) contains noise, so it is discarded, while L(n) is processed for data recovery. In this paper, for our analysis, we considered Haar, Daubechies (DB2), biorthogonal (Bior5.5), and Symlet (Sym4) wavelet transforms. Our consideration is based on the results in [45][46][47]. e results show that these transforms are the most suitable for waveform design because of their resiliency to channel noise.

Haar Wavelet.
e Haar wavelet, discovered by a Hungarian mathematician [48], is a sequence of rescaled "square-shaped" functions which together form a wavelet family or basis. Both wavelet function and scaling function are square-shaped as shown in Figures 3 and 4. e simplest example of an orthogonal wavelet is the Haar function  [49] and mathematically expressed in equations (8) and (9): Its scaling function φ(t) can be described as

Daubechies Wavelet.
Daubechies wavelet is orthogonal, and it is characterized by a maximal number of vanishing moments for some given support. Daubechies wavelets are usually characterized by dbN, N referring to the order number. Figures 5 and 6 demonstrate the Db4 wavelet and scaling functions. In this paper, the Db4 wavelet is used.

Symlet Wavelet.
e Symlet wavelet transforms are in the N order (Sym4); in this paper, we used the Sym4 wavelet.
e Symlets are orthogonal, nearly symmetrical, and biorthogonal wavelets. ey are a modification of the Db family to improve symmetry [50]. Figures 7 and 8 represent the Sym4 wavelet and scaling functions.

Biorthogonal Wavelet.
is is a wavelet function where the associated wavelet transform is invertible but not necessarily orthogonal. In many cases, it is required to choose a wavelet and scaling function such that they meet the condition of mirrored impulse response filters, without the loss of orthogonality [51]. In the biorthogonal case, there are two scaling functions for decomposition and reconstruction which must satisfy the following biorthogonality condition and are expressed mathematically in equation (10)

Simulation Results' Analysis
Here, a grayscale image having resolution 800 × 800 pixels of 8 bits depth is fed into the MATLAB simulator as the test data. In total, the image has 5,120,000 bits, which are enough for our simulation. e simulation parameters for the OFDM and OWDM are shown together in Table 1. e major impacting factor is the communication channel. For a more practical approach, we considered the additive white Gaussian noise (AWGN) channel.

BER Performance Analysis.
Here, we present the BER versus SNR plot for each candidate and also some images to show their qualities at a varied SNR. An AWGN channel is assumed. From the graphical result, the wavelet transforms show a lower BER than the Fourier transforms and wider BER performance with increasing SNR in Figure 11. e lower BER result is due to the wavelet-based waveform having properties such as orthonormality and the ability to encode signals both with time and frequency localization simultaneously as opposed to Fourier transform which can  Scientific Programming only analyze signals with time localization only. is wavelet transform property enables efficient encoding (and decoding) of signals, hence the robustness to the channel error.

PSD and PAPR Performance.
e PAPR is a KPI of a wireless communication system as it goes a long way in shaping the design of the power amplifier's level of linearity and therefore its cost. PAPR is evaluated by computing the complementary cumulative distribution function (CCDF) of the waveform with respect to the number of subcarriers and constellation order. Transmit PAPR performance is given in Table 2, and the plot of the received PAPR against a varied SNR is shown in Figure 12 for the Fourier-OFDM and the wavelet modulations.
At transmission and at reception with a varied SNR of 1 dB to 10 dB, all the wavelet variants have better and distinct PAPR performance than the OFDM with the Haar wavelet having the best performance. Although the wavelet transforms have lower PAPR, they use more transmit power than Fourier. In Figure 12, a plot of the received PAPR at various SNRs is shown, including the power spectral density performance (PSD images) of various transforms at 128 subcarriers each.
In a nonlinear amplifier, OFDM is susceptible to spectral regrowth compared to other wavelets due to its high PAPR. e theory behind this is the broadening of a bandwidth of a modulated signal with large envelope fluctuations due to nonlinearities that generate mixing products between the individual frequency components of the spectrum. e end result is adjacent channel interference. Figures 13-17 are the PSD plots of various transforms. OFDM has a higher sidelobe (noise) than the rest of the wavelet transforms. Table 3 is the bandwidth result from transmitting the test data at 7 GHz as specified at the beginning of this section. e very high use of bandwidth by Fourier (low spectral efficiency) is as a result of the need for cyclic prefixing.

Effect of the Carrier Frequency Offset.
In this section, we assume that both users are perfectly synchronized in the time domain but with an offset between their respective carrier frequencies. In Figure 18, we present the BER curve at CFO � 0.1 kHz. e simulation result shows that OFDM suffers the most effect from CFO, while Haar incurs the least effect. Also, it is observed that the performance disparity between the transforms increases roughly with the SNR.    e test data as described at the beginning of Section 5 are transmitted and received using various transforms to measure the impact of multipath fading on them. e simulation parameters are also exactly as given in the aforementioned section, i.e., four taps with their respective channel gains in a Rayleigh multipath fading channel. In order to observe the maximum BER per SNR, channel state     Scientific Programming information (CSI) and equalization were not considered. It is observed that the OWDM transforms are considerably robust to the multipath fading effect. In Figure 19, OFDM and OWDM's BER vs. SNR in the frequency-selective Rayleigh fading channel are graphically demonstrated.

Overhead Cost and Complexity of Implementation.
e time and memory requirements for both at the transmitter and at the receiver are simulated and shown in Table 4. e simulation of the overhead cost is based on the transmission and reception of the image with the size as described at the beginning of Section 4. For the purpose of accuracy, the time and memory computation costs are limited to IFFT/FFT and IDWT/DWT only.
In Table 4, it is observed that although OWDMs might seem like an attractive choice, they generally require more computational resources than the OFDM.

OFDM and OWDM Evaluation Metrics
Using the simulation results above, we assess OFDM and OWDM for a number of KPIs, taking the 5G set standards into consideration. ese comparisons are outlined in Table 5.    PAPR is low, and computational complexity is high. Haar has the lowest processing time, but memory requirement is higher than other wavelet pairs.
Low device complexity Needs one block per process; IFFT and FFT.
Require a larger device processing capacity. Wavelet transforms generally need two blocks (i.e., their filter banks) for each process (i.e., IDWT and DWT) and more memory than Fourier. However, advances in the clock speeds and memory sizes of communication devices have increased by 4 to 6 orders of magnitude in the past 40 years [52]. erefore, future wise, complexity might not be a challenge.

High reliability
Has poorer BER performance compared to OWDM. Have better BER performance under a wide varied SNR.
Low latency Requires the use of CP to reduce ISI which resultantly reduces throughput. Do not require CP.
High spectral efficiency It has a considerable spectral efficiency. ey have better spectral efficiency compared to Fourier due to Fourier's requirement of higher bandwidth (CP).

Massive asynchronous transmission
Spectral localization of the subcarriers is weak and highly susceptible to the CFO effect.
ey are more localized in time and space. Consequently, they are more immune to the CFO effect.
MIMO compatibility OFDM is quite compatible with MIMO because of its ease of implementation.
e use of OWDM with MIMO is feasible and has been documented in the literature [36].

Frequency-time channel selectivity
OFDM is robust to frequency-selective channels and can be made robust to time channel selectivity by a proper choice of subcarrier spacing.
OWDM is more robust to frequency-selective channels, especially at low SNRs.

Flexibility and scalability
By proper choice of design parameters, OFDM is a flexible waveform that can support diverse services, with several evolved versions.
OWDM is also a flexible waveform. More so, there are different wavelet transforms with different scalable properties. erefore, its flexibility [53] could be explored and tailored to the requirements of the 5G NR classifications. e proposed application guidelines are given in Table 6 based on the 5G NR design criteria and waveform assessment discussed in [54].

Conclusion
e research presented in this paper provides a deep insight into the consideration of OWDM for 5G NR physical layer design and beyond. KPI assessment of OFDM and OWDM and their respective performance simulation results have been carried out. Our results show that OWDM outperforms OFDM in many of the KPIs, and it is, therefore, a more efficient IoT enabler for healthcare and other vital areas. However, our results also show that the main drawback of OWDM is high memory and time cost. In view of this, careful tradeoff considerations are required. Furthermore, we also include uplink, downlink, side link, V2X, and backhaul links as further assessments.
ese various link assessments are necessary for OWDM waveform numerology establishments for 5G's diverse applications. Finally, we observed that, in the establishment of OWDM waveform numerologies for 5G, CP will not be required. is means the establishment process can be less complicated than that of OFDM.

Data Availability
No data were used to support this study.

Conflicts of Interest
e authors declare that there are no conflicts of interest regarding the publication of this paper.