The Scientific World Journal

Volume 2013 (2013), Article ID 828313, 7 pages

http://dx.doi.org/10.1155/2013/828313

Research Article

Design and Synthesis of Metal Complexes of (2E)-2-[(2E)-3-Phenylprop-2-en-1-ylidene]hydrazinecarbothioamide and Their Photocatalytic Degradation of Methylene Blue

P. Murali Krishna,¹ N. B. Gopal Reddy,¹ Nagaraju Kottam,¹ B. C. Yallur,¹ and Hussain Reddy Katreddi²

¹Department of Chemistry, M. S. Ramaiah Institute of Technology, Bangalore 560 054, India

²Department of Chemistry, Sri Krishnadevaraya University, Anantapur 515 006, India

Received 1 August 2013; Accepted 20 August 2013

Academic Editors: A. Hursthouse and C. Zhang

Copyright © 2013 P. Murali Krishna et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract.

The photocatalytic degradation has been considered to be an efficient process for the degradation of organic pollutants, which are present in the effluents released by industries. The photocatalytic bleaching of cationic dye methylene blue was carried out spectrometrically on irradiation of UV light using Cu(II), Ni(II), and Co(II) complexes of (2E)-2-[(2E)-3-phenylprop-2-en-1-ylidene]hydrazinecarbothioamide (HL). The effects of pH and metal ion were studied on the efficiency of the reaction. Cu(II) complex shows better catalytic activity and the highest percentage degradation (88.8%) of methylene blue was observed at pH 12. A tentative mechanism has also been proposed for the photocatalytic degradation of methylene blue.

1. Introduction

Water pollution can be defined as any physical, chemical, or biological alteration in water quality that affects living organisms. Industries and human communities are the main sources, which mainly caused the pollution of surface waters like rivers, lakes, and seas [1]. Dye is a common contaminant or pollutant compound that can be easily found in wastewater [2]. Many industries are using dyes to colour their products, and they consume substantial volumes of water. The presence of small amounts of dyes in water is highly visible and undesirable [3]. Dyes are mainly applied in textile manufacturing, leather tanning, paper production, and food technology industries. The discharge of the major constituent of pollutants in wastewater into water sources from textile and other industries affects water quality including temperature, turbidity, pH, alkalinity, acidity BOD, COD, and colour. The discharge of those coloured wastewaters in the ecosystems causes serious environmental problems like aesthetic pollution and eutrophication and can originate dangerous by-products through oxidation, hydrolysis, or other chemical reactions in the wastewater phase [4, 5]. Therefore, the wastewater treatment is desirable to overcome this problem. Methylene blue is a kind of cationic dye (basic dye) containing heterocyclic aromatic chemical compound with the molecular formula C₁₆H₁₈N₃SCl. This dye is generally classified as a basic dye and cationic species due to the presence of positively charged quaternary nitrogen atoms (as or = ). These groups enhance the solubility of dye in water due to their ionic characteristic [6]. Several methods of treatment of effluents have been undertaken from time to time; the most common methods are chemical precipitation and biological methods. However, these methods suffer from many disadvantages, but photocatalytic degradation seems to be the most promising advanced oxidation processes (AOPs) since it is of low cost and less time consuming [7] and is based on the generation of hydroxyl radicals [8, 9], which can be used for nonspecific oxidation of a wide range of organic compounds. AOPs include the classical Fenton reaction as well as its modifications (e.g., light assisted Fenton oxidation or ferrioxalate-photo Fenton oxidation) as well as H₂O₂/UV or ozonization [10–14]. However, Fenton’s reagent can work only under acidic conditions (pH 2–4), and some dyes are not completely decomposed [15, 16]. Another set of AOP reactions makes use of transition metal ions (mostly Cu) in combination with ligand molecules for the decomposition of hydrogen peroxide and the resulting production of hydroxyl radicals. The main advantage of such systems is the broad substrate specificity and the ability to perform at pH 3–9 [16, 17]. Copper(II) complex systems have been used for the degradation of lignin [18], polycyclic aromatic hydrocarbons [19], and synthetic dyes [17, 20]. Hence, researchers are keen to search for a low-molecular weight ligand with high decolonization efficiency to be used in these reactions and to demonstrate the involvement of hydroxyl radicals in the decolonization reaction. The literature survey reveals that the metal complexes used for the degradation of dyes are nitrogen and oxygen containing copper complexes, and we are not aware of the literature about the usage of copper, nickel, and cobalt complexes containing sulphur and nitrogen as donor atoms. Herein, we report for the first time the results of our attempts to reduce/remove the methylene blue dye from sewage water using copper(II), nickel(II), and cobalt(II) complexes of (2E)-2-[(2E)-3-phenylprop-2-en-1-ylidene]hydrazinecarbothioamide.

2. Experimental

2.1. Materials and Methods

All the reagents used were of analytical grade and used without further purification. Thiosemicarbazide and (2E)-3-phenylprop-2-enal were purchased from Sigma-Aldrich, Bangalore, India. Metal chlorides were purchased from Merck. Methylene blue (MB) was purchased from S D Fine Chem. Limited, Mumbai. All the solvents were used as supplied without further purification.

The ligands and complexes were analyzed for their C, H, and N estimated on Perkin-Elmer 2400 CHN elemental analyser. Infrared spectra were recorded in the 4000–400 cm⁻¹ region (KBr disc) on a Nicolet protege 460 FT-IR spectrophotometer. The molar conductance () in DMF at 30    2°C was measured with a CC180 model (ELICO) direct reading conductivity bridge. Magnetic susceptibility measurements were made for all the complexes at 298 K using magnetic susceptibility balance (Sherwood Scientific, Cambridge, UK). High purity hydrated copper sulphate was used as a standard.

2.2. Preparations of Ligand (HL)

The ligand was prepared by condensing thiosemicarbazide with (2E)-3-phenylprop-2-enal by following the general procedure [21] given in Scheme 1. To a 5% glacial acetic acids in water solution (20 mL) of thiosemicarbazide (1 mol), add ethanolic solution (10 mL) of (2E)-3-phenylprop-2-enal (1 mol) the mixture was refluxed for 2-3 hrs. The crystalline product was collected by filtration, washed several times with hot water, and dried. All the thiosemicarbazones were recrystallised from ethanol.

Scheme 1: Synthesis of ligand and its complexes.

2.3. Preparation of Complexes

The synthesis of complexes was based on the general procedure. To a solution of Ligand (HL) in 15 mL of methanol, appropriate metal chlorides were added and refluxed for 3 hrs. The formed precipitate was then filtered off, washed with cold methanol, and dried.

2.4. Photocatalytic Activity

A photocatalytic activity of metal complexes (MC) on the degradation of methylene blue (MB) in water was examined with and without UV-light (Figure 1). A 300 W high pressure mercury-vapour lamp () is a light source. It is well known that the adsorption and degradation of methylene blue in aqueous solution by the catalyst take place simultaneously. Hence, the effect of aqueous pH on the adsorption and degradation of methylene blue was investigated at the pH values of 3, 8.2, and 12, respectively. Then, the percentage degradation of dye was calculated using the following equation:

where and are the initial and final concentration of the dye. The initial and final concentration of the dye were measured at regular intervals using a UV-visible spectrophotometer.

Figure 1: Photocatalytic experimental setup.

3. Results and Discussion

3.1. Analytical Data and Magnetic Moments

All the three complexes were found to be air stable and readily soluble in aprotic solvents such as DMF and DMSO due to the substituted groups which increase repulsion and thereby reduce the aggregation of molecules. The solubility decreases in strongly polar solvents such as methanol, ethanol, and water because the alkyl groups and other substituted groups are lipophilic and weakly polar [22]. The conductivity data suggest nonelectrolytic nature of complexes [23]. Room temperature magnetic moment data (Table 1) of the complexes suggest that the complexes were monomeric in nature and that the metal-metal interaction was absent.

Table 1: Analytical data of ligands and their complexes.

Complexes
Yield

(%)
M.P

(°C)
Elemental analysis found (Cal.)

Molar conductance

Electronic spectral data

Carbon
Hydrogen
Nitrogen
Sulphur
(BM)
Electronic transition
Assignment

HL·H₂O
90
114-115
58.41 (58.50)
5.20 (5.40)
20.49 (20.48)
15.51 (15.62)
—
—
—
—

Co(L)₂Cl₂
75
116–118
44.08 (44.45)
4.20 (4.10)
15.14 (15.55)
15.36 (11.87)
1.79
6
8710 (20.3)
→,

15385 (14.7)
(F)→(F)

29412 (151.2)
(F)→(P)

Ni(L)₂
80
255-256
52.26 (51.42)

4.82 (4.64)
17.88 (17.98)
13.85 (13.73)
3.39
15
12658
(F)→(F)

21505
(F)→T1g(F)

28985
(F)→(F)

Cu(L)₂Cl₂·2H₂O
72
185–188
41.60 (41.34)
4.23 (4.51)
14.45 (14.46)
11.20 (11.03)
1.58
10
12658 
d-d band

charge transfer band

22222

3.2. Infrared Spectra

The IR spectra of the complexes are compared with the ligand spectra. Important infrared spectral data and their tentative assignments are presented in Table 2. The band assigned to (C=N) at 1621 cm⁻¹ in the spectrum of the ligand shifts to 1567–1615 cm⁻¹ in the spectra of complexes suggesting coordination of the imine nitrogen. Coordination of azomethine nitrogen is confirmed with the presence of new band at 355–443 cm⁻¹, assignable to (M–N) [24, 25]. The IR spectrum of free ligand exhibits a medium band at 3153 cm⁻¹, which is assigned to (N–H) vibration. The absence of (N–H) band in the spectrum of complex provides a strong evidence for the ligand coordination around metal ion in its deprotonated form in nickel complex (except for copper and cobalt complexes). The absorption attributed to (C=S) at 1178 cm⁻¹ in the spectra of the free ligand shifts to 1159 cm⁻¹ in the spectra of the copper complex, indicating coordination through a thioketonic sulphur, whereas in Ni(II) complex the disappearance of (C=S) and the presence of new band at 677 cm⁻¹ indicate the coordination of thiolate sulphur [26] and also the presence of (M–S) band at 472 cm⁻¹ [27, 28].

Table 2: Infrared vibrational bands (cm⁻¹) of ligands and their complexes with tentative assignment.

Ligand/complex
(NH₂)
(NH)
(C=N)
(C=S)
(C–S)
(M–N)
(M–S)

HL.H₂O
3417 (br), 3261 (s)
3153 (br)
1621 (br)
1178 (s)
—
—

Co(L)₂Cl₂
3416 (br), 3261 (s)
3154 (br)
1610 (br)
—
—
443 (s)
—

Ni(L)₂
3426 (br), 3228 (s)
—
1567 (s)
—
677
355 (s)
472

Cu(L)₂Cl₂·2H₂O
3463 (br), 3211 (s)
3050 (br)
1615 (br)
1159 (s)
—
—

3.3. Electronic Spectra

The electronic spectra of the complexes are recorded in DMSO solvent and are given in Table 1. The electronic spectra of copper complex show charge transfer bands in high energy region and d-d bands in low energy region. The d-d band is assigned to → transition suggesting distorted octahedral structure with moderate Jahn-Teller effect. But in the case of nickel(II) and cobalt(II) complexes, three bands are observed. These bands are assigned to the following transitions in the favour of octahedral structure:

 for Nickel(II) complex: , and , for Co(II) complex: , and .

Based on the analytical data and spectral data, tentative structures of the complexes are shown in Figure 2.

Figure 2: Tentative structures of copper(II), Ni(II), and Co(II) complexes.

3.4. Photocatalytic Activity of Metal Complexes

The activities of the catalysts were evaluated in the photodegradation of MB at room temperature. 100 mg of MC was added into 100 mL of aqueous MB solution (5 mg/L), and the solution was stirred for about 15 min. The solution was then exposed to UV light at a distance of 4-5 cm between the liquid surface and the lamp. The solution kept stirring during irradiations. Photocatalytic degradation using different MCs viz copper, nickel, and cobalt complexes was studied (Figure 3). Experimental results show that copper complex shows maximum degradation at 12 pH (Figure 4). The observed high photocatalytic activity is awkward due to the delocalization of electrons in the conjugated MC as the photocatalytic effect depends on the enhancement in electron-hole (/) separation [29].

Figure 3: Degradation of methylene blue under UV light.

Figure 4: % degradation of methylene blue at different pH conditions.

3.4.1. The Effect of Solution pH

The effect of pH on the adsorption of methylene blue on metal complex has been studied by selecting the pHs 3, 8.2, and 12. The results are summarized in Table 3. In general, the photochemical degradation depends strongly on the pH of the reaction medium and the same is observed in the present study. The uptake of methylene blue increased rapidly with the increase of pH. The dye degradation is more favorable at higher pH condition due to the formation of more OH radicals, which will be utilized for oxidative degradation of methyl blue. A similar investigation reported that the adsorption of dye increased by increasing the solution pH [7].

Table 3: Decolorization of dyes using Cu(II), Ni(II), and Co(II) complexes.

Dye/metal complex (5 mg)
% of removal at pH’s without UV
% of removal at pH’s with UV

3.0
8.2
12.0
3.0
8.2
12.0

Methylene blue
No change
13.82
24.0
5.69
29.93
47.73

Co(L)₂Cl₂
14.78
14.78
44.66
9.24
9.24
83.07

Ni(L)₂
7.9
29.93
35.72
38.8
22.18
80.44

Cu(L)₂Cl₂·2H₂O
33.92
8.83
33.44
43.33
3.3
88.80

Mechanism. Metal complex system produced hydroxyl radicals during the catalytic reaction. This is not surprising, since the production of –OH was already confirmed in other metal-based AOP systems [17, 30]. The radicals are strong oxidizing agents that react with dyes and cause their decolorization. The tentative mechanism has been proposed for the degradation of methylene blue in the presence of copper, nickel, and cobalt complexes and light (Figure 5).

Figure 5: Photodegradation mechanism of metal complex.

Consider

4. Conclusions

Co(II), Ni(II), and Cu(II) complexes of (2E)-2-[(2E)-3-phenylprop-2-en-1-ylidene]hydrazinecarbothioamide (HL) are synthesized and characterized based on the various spectroscopic techniques. The rate of photocatalytic degradation of methylene blue using prepared metal complexes was successfully carried out under UV light. The increasing order of the rate with different metal complexes is as follows: Cu(II)    Co(III)    Ni(II). The generation of the hydroxyl radical is responsible for the degradation of dye photocatalytically. The dye has been successfully degraded 88.8% in the presence of copper complex in UV light at pH 12.

Conflict of Interests

The authors declare that they have no conflict of interests.

Acknowledgments

The authors are thankful to Visvesvaraya Technological University, Belgaum, for financial support (VTU/Aca./2010-11/A-9/13261 dated January 17, 2011) and M. S. Ramaiah Institute of Technology, Bangalore, for providing facilities.

References

V. J. Inglezakis and S. G. Poulopoulos, AdsorptIon, Ion Exchange and Catalysis: Design of operatIons and Environmental applicatIons, Elsevier, 2006.

E. Forgacs, T. Cserháti, and G. Oros, “Removal of synthetic dyes from wastewaters: a review,” Environment International, vol. 30, no. 7, pp. 953–971, 2004.

S. Naghiloo, A. Habibi-Yangjeh, and M. Behboudnia, “Adsorption and photocatalytic degradation of methylene blue on Zn1-xCuxS nanoparticles prepared by a simple green method,” Applied Surface Science, vol. 257, no. 6, pp. 2361–2366, 2011.

A. B. Prevot, C. Baiocchi, M. C. Brussino et al., “Photocatalytic degradation of Acid Blue 80 in aqueous solutions containing TiO₂ suspensions,” Environmental Science and Technology, vol. 35, no. 5, pp. 971–976, 2001.

B. Neppolian, H. C. Choi, S. Sakthivel, B. Arabindoo, and V. Murugesan, “Solar light induced and TiO₂ assisted degradation of textile dye reactive blue 4,” Chemosphere, vol. 46, no. 8, pp. 1173–1181, 2002.

R. M. Christie, Colour Chemistry, Royal Society of Chemistry Paperbacks, 2001.

S. Lodha, A. Jain, V. K. Sharma, and P. B. Punjabi, “Photocatalytic degradation of rhodamin-b using metal complexes and hydrogen peroxide,” Indonesian Journal Chemistry, vol. 42, pp. 42–46, 2008.

A. R. Khataee and M. B. Kasiri, “Photocatalytic degradation of organic dyes in the presence of nanostructured titanium dioxide: influence of the chemical structure of dyes,” Journal of Molecular Catalysis A, vol. 328, no. 1-2, pp. 8–26, 2010.

A. Kajbafvala, H. Ghorbani, A. Paravar, J. P. Samberg, E. Kajbafvala, and S. K. Sadrnezhaad, “Effects of morphology on photocatalytic performance of Zinc oxide nanostructures synthesized by rapid microwave irradiation methods,” Superlattices and Microstructures, vol. 51, no. 4, pp. 512–522, 2012.

W. G. Kuo, “Decolorizing dye wastewater with Fenton's reagent,” Water Research, vol. 26, no. 7, pp. 881–886, 1992.

D. F. Ollis and H. Al-Akabi, Photocatalytic Purification and Treatment of Water and Air, Elsevier, Amsterdam, The Netherlands, 1993.

I. Arslan and I. A. Balcioglu, “Degradation of commercial reactive dyestuffs by heterogenous and homogenous advanced oxidation processes: a comparative study,” Dyes and Pigments, vol. 43, no. 2, pp. 95–108, 1999.

I. Arslan, I. A. Balcioǧlu, and D. W. Bahnemann, “Advanced chemical oxidation of reactive dyes in simulated dyehouse effluents by ferrioxalate-Fenton/UV-A and TiO₂/UV-A processes,” Dyes and Pigments, vol. 47, no. 3, pp. 207–218, 2000.

F. Herrera, J. Kiwi, A. Lopez, and V. Nadtochenko, “Photochemical decoloration of Remazol Brilliant Blue and Uniblue A in the presence of Fe³⁺ and H₂O₂,” Environmental Science and Technology, vol. 33, no. 18, pp. 3145–3151, 1999.

K. H. Gregor, “Oxidative decolorization of textile waste with advanced oxidation processes,” in Chemical Oxidation: Technologies for Nineties, W. W. Eckendfelder, A. R. Bowers, and J. A. Roth, Eds., pp. 161–193, 1992.

F. Nerud, P. Baldrian, J. Gabriel, and D. Ogbeifun, “Decolorization of synthetic dyes by the Fenton reagent and the Cu/pyridine/H₂O₂ system,” Chemosphere, vol. 44, no. 5, pp. 957–961, 2001.

P. Verma, P. Baldrian, and F. Nerud, “Decolorization of structurally different synthetic dyes using cobalt(II)/ascorbic acid/hydrogen peroxide system,” Chemosphere, vol. 50, no. 8, pp. 975–979, 2003.

T. Watanabe, K. Koller, and K. Messner, “Copper-dependent depolymerization of lignin in the presence of fungal metabolite, pyridine,” Journal of Biotechnology, vol. 62, no. 3, pp. 221–230, 1998.

J. Gabriel, V. Shah, K. Nesměrák, P. Baldrian, and F. Nerud, “Degradation of polycyclic aromatic hydrocarbons by the copper(II)-hydrogen peroxide system,” Folia Microbiologica, vol. 45, no. 6, pp. 573–575, 2000.

I. A. Salem, “Kinetics of the oxidative color removal and degradation of bromophenol blue with hydrogen peroxide catalyzed by copper(II)-supported alumina and zirconia,” Applied Catalysis B, vol. 28, no. 3-4, pp. 153–162, 2000.

P. Murali Krishna, K. Hussain Reddy, J. P. Pandey, and D. Siddavattam, “Synthesis, characterization, DNA binding and nuclease activity of binuclear copper(II) complexes of cuminaldehyde thiosemicarbazones,” Transition Metal Chemistry, vol. 33, no. 5, pp. 661–668, 2008.

Z. Chen, Y. Wu, D. Gu, and F. Gan, “Nickel(II) and copper(II) complexes containing 2-(2-(5-substitued isoxazol-3-yl)hydrazono)-5,5-dimethylcyclohexane-1,3-dione ligands: synthesis, spectral and thermal characterizations,” Dyes and Pigments, vol. 76, no. 3, pp. 624–631, 2008.

H. H. Willard, L. L. Merritt, J. A. Dean, and F. A. Settle, Instrumental Methods of Chemical Analysis, C.B.S. Publishers, 1986.

V. Suni, M. R. P. Kurup, and M. Nethaji, “Structural and spectral investigations on some new Ni(II) complexes of di-2-pyridyl ketone N(4)-phenylthiosemicarbazone,” Polyhedron, vol. 26, no. 13, pp. 3097–3102, 2007.

D. X. West, A. A. Nassar, F. A. El-Saied, and M. I. Ayad, “Nickel(II) complexes of 2-aminoacetophenone N(4)-substituted thiosemicarbazones,” Transition Metal Chemistry, vol. 23, no. 4, pp. 423–427, 1998.

K. Alomar, A. Landreau, M. Kempf, M. A. Khan, M. Allain, and G. Bouet, “Synthesis, crystal structure, characterization of zinc(II), cadmium(II) complexes with 3-thiophene aldehyde thiosemicarbazone (3TTSCH). Biological activities of 3TTSCH and its complexes,” Journal of Inorganic Biochemistry, vol. 104, no. 4, pp. 397–404, 2010.

K. Nag and D. S. Joarder, “Metal complexes of sulfur-nitrogen chelating agents. V. 2-N-Ethylaminocyclopentene-1-dithiocarboxylic acid complexes of Ni(II), Pd(II), Pt(II), Co(II), Co(III), and Cu(I),” Canadian Journal of Chemistry, vol. 54, pp. 2827–2831, 1976.

R. Roy, M. Chaudhury, S. K. Mondal, and K. Nag, “Metal complexes of sulphur-nitrogen chelating agents. Part 11: synthesis, characterisation, and thermodynamics of nucleophilic substitution reactions of monohalogeno nickel(II) complexes of tridentate ligands of the type SNN in solution and the solid state,” Journal of the Chemical Society, Dalton Transactions, no. 8, pp. 1681–1686, 1984.

K. K. Senapati, C. Borgohain, K. C. Sarma, and P. Phukan, “Photocatalytic degradation of methylene blue in water using CoFe 2O₄-Cr₂O₃-SiO₂ fluorescent magnetic nanocomposite,” Journal of Molecular Catalysis A, vol. 346, no. 1-2, pp. 111–116, 2011.

G. Tabbì, S. C. Fry, and R. P. Bonomo, “ESR study of the non-enzymic scission of xyloglucan by an ascorbate-H₂O₂-copper system: the involvement of the hydroxyl radical and the degradation of ascorbate,” Journal of Inorganic Biochemistry, vol. 84, no. 3-4, pp. 179–187, 2001.